Used Operating Resolution for sale (26,653)

Condition: ready for operation (used), Year of construction: 2018, This DENSO RC8A was manufactured in 2018. It features a robotic cell with two SCARA robots, each capable of a maximum reach of 550 mm and a Z-axis stroke of 320 mm. The system includes a controller RC8A, offline programming software, and self-diagnostic functions. Ideal for applications requiring high-speed robotic manipulation. Contact us for more information about this machine. • Motion & Control: • Point-to-point control system • Linear and circular movement in 3 dimensions • Memory Capacity: • Variables memory: 1.75 MB (approx. 65000 points) • Program memory: 400 MB • Up to 256 programs • 5000 instructions per program • I/O Signals: • Inputs: • 8 user inputs at robot wrist (Hand I/O) • 8 user inputs at controller (Mini I/O) • 8 system inputs • Outputs: • 8 user outputs at robot wrist (Hand I/O) • 7 user outputs at controller (Mini I/O) • 8 system outputs • Communication Interfaces: • 1 × RS-232C • Gigabit Ethernet • 2 × USB • Additional Features: • Self-diagnostic functions • Operating conditions: • Temperature: 0–40 °C • Humidity: ≤ 90% RH • Controller Dimensions & Weight: • Standard RC8A: 357 × 320 × 94 mm • RC8A with Safety Motion: 411 × 320 × 94 mm • Volume: 12.4 liters • Weight: 12 kg • Cables: • Power cable: 5 m • I/O cable: 8 m (optional) • Teaching Pendant: • Quantity: 1 unit (for both robots) • Cable length: 4 m (optional 8 m / 12 m) • Display: • 7.5" TFT LCD touchscreen • Resolution: 640 × 480 pixels • Power supply: 24 V • Protection class: IP65 (dust & splash resistant) • Dimensions: 290 × 198 × 80 mm • Weight: approx. 1 kg • Functions: • Program creation and editing • Parameter configuration • Robot jogging and motion control • Program start • Teaching and verification mode • I/O management • Communication setup • Error displayRobots • Quantity: 2 units • Type: SCARA • Mechanical Characteristics: Klsdpfx Adox Uty Hjdsl • Maximum reach: 550 mm • Z-axis stroke: 320 mm • Repeatability (J1 + J2): ±0.012 mm • Repeatability (Z-axis): ±0.01 mm • Repeatability (T-axis): ±0.004° • Payload capacity (wrist): 8 kgSpeed • Maximum composite speed: 8780 mm/sec • Z-axis speed: 2760 mm/sec • T-axis speed: 220°/secRobot Arm Connections • Pneumatic connections: • 4 air tubes, Ø 6 mm • Electrical signals: • 24 signals via connectorRobot Features • Offline programming software • Absolute encoders • Sealed AC servo motors, brushless and maintenance-free • Power supply: Single-phase or three-phase 230 VAdditional Equipment • 2 gripping devices with sensors for detecting picked quantity • 1 electrical control cabinet interfacing the entire systemMachine History • Functional Description: The robotic cell was originally designed to feed a cutlery packaging machine. The system picked stacked forks from dedicated crates and transferred them onto a packaging conveyor at a loading speed of 100 pieces per minute. While the two SCARA robots were operating correctly, the crate exchange system (empty vs. full crates) was not optimally designed. For this reason, the robotic cell was eventually decommissioned. A short video of the robot in operation is available.

Condition: used, This listing is for a Varian Autosampler Model 410 unit on it's own. The Varian ProStar 410 HPLC Autosampler has variable injection volumes and automixing/autodiluting. The ProStar 410 is perfect for laboratories with changing needs. It provides flexible operation without sacrificing reliability or performance. Multiple injection modes for flexibility, ease of use, and precision. Full loop filloverfills the sample loop for maximum precision. Partial loop fill allows easily programmed variable injection volumes. Microliter pickup withdraws the exact amount to be injected without sample loss. The Varian ProStar 410 AutoSampler offers the best of both worlds. It is intelligent for research applications yet rugged enough for routine quality control work. With Pressure Assisted Sampling Aspiration (PASA), the Varian 410 ProStar AutoSampler applies pressure within the vial while the sample is withdrawn by a high-resolution syringe. Air bubbles and in-vial vacuum problems are eliminated resulting in excellent reproducibility. Flexibility with multiple injection modes Optimal performance with integrated column oven Biocompatible and sample cooling options available Specifications: Standard sample tray 84 x 1.5 mL vials with 3 x 10 mL vials Optional sample trays 96 x 2.5 mL vials or 24 x 10 mL vials Dispenser unit 50 µL syringe standard; 1000 µL or 2500 µL syringes, optional Injection volume 1 to 5000 µL with preparative option up to 10 mL Injection methods nine methods in memory Needle wash integrated, programmable large reservoir Vial detection Yes Reproducibility Full Loop: < 0.3% RSD Partial Loop: < 0.5% RSD Microliter Pickup: < 1.0% RSD Carryover < 0.05% Optional sample cooling 4°C to 15°C programmable Can be refurbished on request, refurbishment not included in price. Klsdpfx Adsxzh Amjdol

Condition: used, This listing is for 1 of 2 Grant-Bio PHMP Thermo-Shaker Excellent temperatures uniformity across the platform/microplate (patented bi-directional heating of microplates) combined with variable speed and variable temperature produces the ideal thermoshaker for microplate incubations. Can be used with all types of standard depth microplates and offers three devices in one for maximum versatility and efficiency. A microplate thermoshaker A compact benchtop incubator without shaking A microplate shaker in cold or ambient temperatures Features Temperature setting range: + 25°C to 100°C Temperature stability ± 0.1°C, temperature uniformity ± 0.2°C due to the bi-directional heating system (platform and lid) Shaking speed: 250 to 1200rpm Rapid heat-up Continuous or timed operation, with alarm buzzer and automatic switch-off facility Choice of two models with capacity for two (PHMP) or four (PHMP-4) 96- or 384-well microplates The heated lid completely covers the flat heating plate to provide bi-directional heating and excellent temperature stability and uniformity, whilst preventing condensation Combination of bi-directional heating and powerful orbital shaking capability produces the maximum yield from incubations Very easy to operate, with simple set-up of temperature, shaking speed and time via push buttons and the 2-line LCD status display Dimensions (h x d x w) - 125 x 250 x 265mm Temperature range - +25 to 60°C Temperature control range - Ambient +5 to 60°C Klodoxzgvfepfx Addjl Stability - 0.1°C Uniformity - 0.25°C Display - 2 line x 16 character LCD Shaking speed - 250 to 1200rmp Speed setting resolution - Increment 10rpm Average heat up speed - 12 minutes from 25 to 37,35 minutes from 25 to 60 Maximum height of microplates - 18mm Capacity - 2 microplates Orbit diameter - 2mm Timer - (with auto-off and audible alarm) 1 minute to 96 hours (1 minute increment) External power supply - Input AC 120-230V, 50/60Hz Output DC 12V Power consumption - 40W (3.3A) Weight - 6.1kg

Condition: used, Year of construction: 2020, CNC-CONTROLLED MACHINING CENTER WITH MULTIFUNCTIONAL TABLE - WORK CELL VERSIONX400 CELLDrilling and milling made for you!The numerically controlled machining center is equipped with a wide range of milling/drilling tools to meet every need in the processing of wood and similar materials.- More powerful, with drilling spindles with 8,000 rpm and . Technology, the toughest spindle available on the market, with over 1,000 maintenance-free hours of use. Better and more comprehensively equipped, with various configuration options thanks to the multifunctional table to optimally equip the machine according to your needs. Easier and more understandable programming thanks to the integrated MAESTRO CNC CAD-CAM module. Easier to use: the work table is accessible at all times, the electrical cabinet and vacuum pump are integrated, and in the PRO SPACE configuration there are no guards. Supporting structure. The supporting structure consists of a particularly strong monolithic steel base, heavily ribbed and very rigid. The particularly wide support was specifically designed to give the machine stability, ensuring consistent precision regardless of the working conditions and eliminating the need to anchor the machine to the floor. The base forms a large and solid support for the mobile column: the work unit is thus equipped with a balanced, stable, and durable support that can withstand the most extreme stresses, ensuring higher quality performance and greater precision. The mobile gantry consists of a single, solid unit anchored to the base on both sides and slides on pyrotechnic guides with top-quality ball-return slides. The dual motorization along the X-axis ensures top performance even under demanding working conditions. The movement of the lower moving unit (X-axis) and the working unit along the rod of the moving unit (Y-axis) is achieved thanks to a rack/pinion transmission with helical teeth. this creates a greater tooth-to-tooth thrust which achieves greater acceleration and greater speed along the X and Y axes. The specially designed helical gearing ensures less wear on the mechanical components and less noise. The vertical Z axis is driven by a screw with ball return which ensures perfect balance with dynamic loading and strong acceleration and deceleration. The main milling unit is directly coupled to the Z axis carriage and ensures absolute quality of finishes as any vibrations are completely eliminated. Translation along the X-Y-Z axes is carried out by brushless motors driven by static inverters; These ensure: - Reduced processing times thanks to improved acceleration - Better positioning accuracy thanks to the high-resolution encoder - Zeroing of setup operations when switching on the machine thanks to absolute encoders - Zeroing of general maintenance operations since there are no brushes with the "brushless" system The management of the axis displacement and, in general, of the machine's working elements is carried out by an industrial NS module with digital D Kledpfovvi N Iox Addsl

Condition: used, Year of construction: 2019, Incl. tools CNC-CONTROLLED MACHINING CENTER morbidelli m100 Drilling and milling made for you! This numerically controlled machining center is equipped with a wide range of milling and drilling tools to meet every woodworking requirement. - Highly powerful - with 8,000 rpm drilling spindles and . technology, the most stable spindle available on the market, with more than 1,000 maintenance-free hours of use. - Optimally and comprehensively equipped - the vacuum cleaners can be individually configured with the TV FLEX work table to customize the machine to meet individual requirements. - Easy and understandable programming thanks to the integrated Cad-Cam MAESTRO CNC software - Easy to operate; the lowered machine frame makes the work table accessible at all times. The control cabinet and vacuum pump are integrated into the machine bed, and in the PRO SPACE version, no additional structural protective measures are necessary. Supporting structureThe supporting structure consists of a particularly strong monolithic steel base, ribbed and very robust. The particularly wide support was specifically designed to give the machine stability, ensuring constant precision in all working conditions. The machine does not need to be anchored to the ground. The base provides a large and solid support for the mobile column: the work unit is equipped with a balanced, stable and resistant support that can withstand the most extreme stresses, ensuring superior performance and greater precision. The mobile gantry consists of a solid single part anchored to the base and the work unit is fixed to it and moves along Y and Z axes, also on prismatic guides with ball return sliding blocks of the highest quality. The movement of the lower moving unit (X-axis) and the working unit along the crosshead of the moving unit (Y-axis) is achieved thanks to the power transmission via a rack and pinion with helical teeth; This creates a greater tooth-to-tooth thrust, which achieves greater acceleration and higher speed along the X and Y axes. The specially designed helical gearing ensures less wear on the mechanical components and less noise. The vertical Z axis is driven by a screw with ball return, which ensures perfect balance with dynamic loading and strong acceleration and deceleration. The main milling unit is directly coupled to the Z axis carriage and ensures very high quality finishing as vibrations are completely eliminated. Translation along the X-Y-Z axes is carried out by brushless motors driven by static inverters. These ensure:- Reduced machining times thanks to improved acceleration- Better positioning accuracy thanks to the high resolution encoder- Elimination of setup operations when switching on the machine thanks to absolute encoders- Elimination of general maintenance operations as there are no brushes with the "brushless" systemThe management of the axis displacement and in general of the working elements of the machine is done via e Kjdpfx Ajvvi Scoddsll

Condition: used, Eagle Pro Pack 240 PRO – Advanced X-Ray Inspection for Packaged Products The Eagle Pro Pack 240 PRO is a high-performance X-ray inspection system designed for maximum product safety, quality assurance, and production efficiency. Ideal for food, pet food, pharmaceutical, and consumer goods applications, this system combines cutting-edge detection technology with robust industrial design. ----- Key Features & Benefits - Reliable detection of foreign contaminants, even in dense or metallized packaging - Multiple quality checks in a single inspection - High inspection accuracy at high production speeds - Hygienic, stainless-steel construction for demanding production environments Technical Specifications Inspection Area - Maximum inspection width: up to 242 mm - Maximum inspection height: up to 101 mm - Conveyor width: approximately 298 mm Detection Capabilities - Detection of metal, glass, stone, mineral bone, and dense plastics - Product integrity checks: - Missing or broken items - Shape and position verification - Fill level and mass/weight control (2-, 3- or 5-zone analysis) X-Ray Technology - Detector resolution: - Up to 0.4 mm (PXT™ dual-energy) - 1.2 mm single-energy Software & Controls - 15” full-color touchscreen HMI - Eagle SimulTask™ PRO image processing software - Windows 10 Enterprise operating system Kljdpfx Aex Srn Reddel - Remote diagnostics via TeamViewer™ Conveyor & Speed - Variable belt speed: 17 – 114 m/min, depending on configuration and product Connectivity - USB 2.0 - Ethernet 10/100/1000 - Optional EtherNet/IP Fieldbus integration Construction & Safety - Hygienic stainless-steel design (IP65/IP66 optional) - Low radiation emission: < 1 µSv/h - Compliant with international X-ray and electrical safety standards (CE / FDA) Operating Conditions - Operating temperature: 0 – 40 °C - Power supply: 230 V AC, 50/60 Hz, single phase Why Choose the Eagle Pro Pack 240 PRO? - Superior detection performance - Increased production uptime - Reduced false rejects - Designed for modern, high-speed production lines

Condition: new, functionality: fully functional, The Table Top Print bagging machine enables efficient packaging and sealing of products in pre-made bags and is suitable for various formats. The machine is easy to operate and features a user-friendly display for setting up, saving jobs, and controlling operating parameters. For maximum flexibility, it offers automatic and manual operating modes with a secure sealing bar. Training a packaging operator takes less than five minutes. With integrated thermal transfer printing technology, bags can be directly printed with high-resolution graphics, text, and barcodes—eliminating the need for separate labeling. Features: - Multi-color display for straightforward settings - Pre-selection of desired product quantity for packaging - Integrated total product counter (with reset function) - Roll change in under one minute - Sealing via foot pedal, automatically, or manual push-button - Feed systems for automatic bag filling available on request Technical Parameters: 1. Maximum bag length: 450 mm 2. Maximum bag width: 250 mm 3. Maximum bag thickness: 0.04–0.1 mm per layer 4. Packaging speed: up to 25 units/minute 5. Supply voltage: 1Ph. 220V 50Hz Kedpoxlzr Ajfx Addoll 6. Power consumption: approx. 1 kW 7. Machine weight: approx. 70 kg (including printer) 8. Machine dimensions: approx. 670 x 665 x 860 mm 9. Print area: 53 x 75 mm 10. Bag type: wicketed bags on rolls Base machine: €12,500 + Thermal transfer printer: €5,500 + Label dispenser: €2,900 + SATO label printer incl. dispenser: €6,500 to €9,000

Year of construction: 2025, condition: as good as new (ex-display), Universal testing machine PM10 Kledpfxjd R Dpme Addol Force: 10 kN cross beam stroke: 700 mm Installation space: 400 mm total height: 1230 mm Weight: ca.85 Kg Travel resolution: 0.01 mm testing speed: 1-500 mm / min Return speed: 700 mm / min Force transducer: 10kN incl. evaluation electronics and basic software. Our testing machines can be operated in stand-alone mode via a numeric keyboard, so that a "quick test" can be carried out without a PC. For tests that require data storage and recording of the curve progression, we offer you the possibility of control and evaluation with the basic software. This allows to generate different test sequences and to create a test protocol. Furthermore, you have the possibility to process the raw data in your own programs. Optional: - Delivery & commissioning -DAkkS or factory calibration according to DIN EN ISO 7500-1 - Clamps: Pressure plates, bending devices, shearing devices, wedge clamps, shear clamps, peeling clamps, screw clamps, pneumatic clamps and hydraulic clamps.

Year of construction: 2024, condition: as good as new (ex-display), Universal testing machine PM5 Kjdpfxod R Dqbo Addell Force: 5 kN crosshead stroke: 520 mm working chamber depth: 66 mm total height: 1036 mm Weight: approx.48 Kg travel resolution: 0,01 mm test speed: 1-500 mm / min Return speed: 700 mm / min Force transducer: 5 kN incl. evaluation electronics and basic software. Our testing machines can be operated in stand-alone mode via a numeric keypad, so that a "quick test" can also be carried out without a PC. For tests that require data storage and recording of the curve progression, we offer you the possibility of control and evaluation with the basic software. This enables you to generate different test sequences and to create a test protocol. Furthermore, you have the possibility to process the raw data in your own programs. Optional: - Delivery & Commissioning -DAkkS or factory calibration according to DIN EN ISO 7500-1 - Clamping fixtures: Pressure plates, bending fixtures, shear fixtures, wedge grips, shear grips, peeling grips, screw grips, pneumatic grips and hydraulic grips.

Condition: as good as new (ex-display), Year of construction: 2025, functionality: fully functional, Universal testing machine PM3 Ksdpefdzupsfx Addjll Force: 3 kN cross beam stroke: 520 mm Working area depth: 66 mm total height: 1036 mm Weight: ca.40 Kg Travel resolution: 0.01 mm testing speed: 1-500 mm / min Cc7d2rmq Return speed: 700 mm / min Force transducer: 3 kN incl. evaluation electronics and basic software. Our testing machines can be operated in stand-alone mode via a numeric keyboard, so that a "quick test" can be carried out without a PC. For tests that require data storage and recording of the curve progression, we offer you the possibility of control and evaluation with the basic software. This allows to generate different test sequences and to create a test protocol. Furthermore, you have the possibility to process the raw data in your own programs. Optional: - Delivery & commissioning - DAkkS or factory calibration according to DIN EN ISO 7500-1 - Clamps: Pressure plates, bending devices, shearing devices, wedge clamps, shear clamps, peeling clamps, screw clamps, pneumatic clamps and hydraulic clamps.

Year of construction: 2025, condition: new, Universal testing machine PM50 Force: 50 kN Kledod R Dp Eopfx Addol cross beam stroke: 1200 mm Installation space: 400 mm Overall height: 1817 mm Weight: ca.380 Kg Travel resolution: 0.01 mm Testing speed: 0.03-1000 mm / min Return speed: 1000 mm / min Force transducer: 50 kN incl. evaluation electronics and basic software. Our testing machines can be operated in stand-alone mode via a numeric keyboard, so that a "quick test" can be carried out without a PC. For tests that require data storage and recording of the curve progression, we offer you the possibility of control and evaluation with the basic software. This allows to generate different test sequences and to create a test protocol. Furthermore, you have the possibility to process the raw data in your own programs. Optional: - Delivery & commissioning - DAkkS or factory calibration according to DIN EN ISO 7500-1 - Clamps: Pressure plates, bending devices, shearing devices, wedge clamps, shear clamps, peeling clamps, screw clamps, pneumatic clamps and hydraulic clamps.

Year of construction: 2025, condition: as good as new (ex-display), Universal testing machine PM3 Force: 3 kN cross beam stroke: 520 mm Working area depth: 66 mm Kjdpfxsd R Dpue Addsll total height: 1036 mm Weight: ca.40 Kg Travel resolution: 0.01 mm testing speed: 1-500 mm / min Return speed: 700 mm / min Force transducer: 3 kN incl. evaluation electronics and basic software. Our testing machines can be operated in stand-alone mode via a numeric keyboard, so that a "quick test" can be carried out without a PC. For tests that require data storage and recording of the curve progression, we offer you the possibility of control and evaluation with the basic software. This allows to generate different test sequences and to create a test protocol. Furthermore, you have the possibility to process the raw data in your own programs. Optional: - Delivery & commissioning -DAkkS or factory calibration according to DIN EN ISO 7500-1 - Clamps: Pressure plates, bending devices, shearing devices, wedge clamps, shear clamps, peeling clamps, screw clamps, pneumatic clamps and hydraulic clamps.

Condition: as good as new (ex-display), Year of construction: 2021, measuring range X-axis: 500 mm, measuring range Y-axis: 500 mm, measuring range Z-axis: 300 mm, Equipment: documentation/manual, lighting, AIM coordinate measuring centers are the technical successors of the Mahr Mahr multisensor coordinate measuring coordinate measuring machines. Technical data: Measuring range: 500 x 500 x 300 mm Dimensions: 1520 x 1040 x 2040 mm weight: approx. 1.200 kg max. workpiece weight: on glass plate approx. 40 kg Accuracies: U1=1,9 + L/200 U2=2,4 + L/150 U3=2,9 + L/100 (L= measuring length in mm) increased accuracy on request traversing speed: 200 mm/s acceleration: 400 mm/s scale resolution: 0.0001 mm Multisensor sensor unit (MSH) optical/tactile/laser -incl. high-precision USB camera with 2-stage zoom with telecentric beam path Kjdpfx Aeg Ewk Reddell -incl. PTL01 TTL point laser, highly accurate, telecentrically coupled in -incl. Renishaw TP200 integrated tactile probe system, optionally extendable -incl. Quad-Light LED Power Ringlight, programmable incident light -incl. LED power transmitted light -incl. Nikon precision lens 5x (optional 3x, 10x, 20x, 50x) C-Mount Technology -incl. calibration standard with factory calibration certificate, consisting of glass plate "circle", calibration sphere and ring gauge Transfer -State-of-the-art PT200 CNC controller system in a solid, industry-standard control cabinet -PCI-BUS system for fast internal data transfer in real-time operation -Extendable 19" controller rack for optimum access in case of servicing -modular controller concept open for later upgrades and retrofits -service-optimized controller design fast access and service times -Integrated 64-bit broadband bus technology with Ech [...]

Condition: new, Year of construction: 2026, The ERBA EVP-RA 550 vibratory finishing machine features a rising work bowl floor with integrated separation. It is equipped with an easily interchangeable screening unit and is distinguished by high operational efficiency thanks to the integrated drop stage. Discharge and separation are performed via the integrated flap (manual/pneumatic operation). Upon request, reinforced suspension and a more powerful motor can be installed for higher loads. The motor speed can be continuously adjusted via a frequency converter (optional). Thanks to its lateral discharge, the EVP-RA 550 can be linked with other machines. The system can optionally be equipped with fully automatic PLC control. ERBA vibratory finishing systems are known for their durability and longevity, which are largely attributed to the hot-poured polyurethane lining of the work bowl. Technical data: - Gross volume: 550 l - Working channel width: 390 mm - Unbalance motor output: 4.0 kW Kodpfx Adjn Ut Uvedjll - Speed: 1,400 rpm - Internal bowl diameter: 1,400 mm Prices listed are net plus the currently applicable statutory VAT and shipping costs. Some images may show the machine with optional accessories that are available at extra cost. If you are interested, we look forward to hearing from you. We are happy to provide you with free and non-binding advice. The European Commission provides an online dispute resolution (ODR) platform for out-of-court settlements. This offer is for online presentation purposes only. Contract negotiations are conducted via telecommunications (email, telephone, messaging portal). In the first step, we will send you a non-binding offer, together with our general terms and conditions, imprint, and the right of withdrawal, before a purchase/contract is concluded.

Condition: new, Year of construction: 2026, The ERBA Separator Line YE-60 is used for separating workpieces from abrasive media. It can be operated as a mobile standalone machine or in combination with other machines, such as the ERBA Turbo (centrifugal finishing system). The separation deck can be quickly and easily swapped, depending on your requirements. An optional frequency inverter can be installed, enabling stepless adjustment of the motor speed. The YE-60 can be equipped with many optional extras to simplify the separation process, such as magnetic separation for small parts, a washing nozzle, or a parts hopper. Technical Data: - Gross volume: 60 L - Motor output: 0.3 kW - Weight: 140 kg - Screen area dimensions: 1000 x 500 mm - Installation dimensions: 1185 x 540 x 575 mm (Length x Width x Height) Kedpfxon Ut N He Addjll All prices are net, VAT at the current legal rate and shipping costs are additional. Some images may show the machine including accessories that are optionally available at extra cost. If you are interested, we look forward to hearing from you. We are happy to advise you without obligation. The European Commission provides a platform for online dispute resolution (OS platform). This offer serves solely as an online presentation of our products. All contract negotiations are conducted via telecommunications (email, telephone, messaging portal). As a first step, we will provide you with a non-binding offer, which will also include information on our general terms and conditions with legal notice and the right of withdrawal, before a purchase/contract is concluded.

Condition: new, Year of construction: 2026, Machine type: EVP 550 Manufacturer: ERBA Power kW: 4.0 Total volume: 585 liters Kledpfxen Ut Tmj Addjl Description: The ERBA EVP 550 vibratory finishing machine features a flat-bottomed working container without an internal separator. The emptying or separation process takes place via bottom discharge (manual/pneumatic operation). Upon request, the machine can be equipped with reinforced suspension and a more powerful motor for heavier-duty applications. Motor speed can be continuously adjusted using a frequency converter (optional). The system can also be fitted with a fully automatic PLC control unit (optional). ERBA vibratory finishing machines are renowned for their durability and longevity, backed by the hot-cast polyurethane lining of the processing container. All prices are net, plus the applicable statutory VAT and shipping costs. Photographs may show the system with accessories that are optionally available at additional cost. If you are interested, we look forward to your inquiry. We would be happy to offer you a consultation without obligation. The European Commission provides a platform for out-of-court online dispute resolution (ODR platform). This offer serves exclusively as an online presentation of our goods. Contract negotiations are conducted via telecommunication (email, telephone, messaging portal). In the initial step, we will send you a non-binding offer, which also includes our terms and conditions, legal notice, and information on the right of withdrawal, prior to any purchase or contract being concluded.

Condition: new, Year of construction: 2026, The EVP-RA 550 vibratory finishing machine from ERBA features a flat working container bottom with integrated separation, designed for processing medium to large workpieces. It is equipped with an easily replaceable screening unit. Emptying and separation are carried out through the integrated flap, which can be operated either manually or pneumatically. Upon request, reinforced suspension and a more powerful motor can be fitted to handle higher loads. The motor speed can be infinitely adjusted using a frequency converter (optional). With its side discharge system, the EVP-A 550 can be linked with other machines for integrated workflows. The system can also be equipped with a fully automated PLC control (optional). ERBA vibratory finishing systems are known for their durability and longevity, which is also attributable to the hot-cast polyurethane lining of the working container. Technical specifications: - Gross volume: 550 liters - Working channel width: 390 mm - Unbalance motor power: 4.0 kW Kjdjn Ut Ugepfx Addell - Speed: 1,400 rpm - Container inside diameter: 1,400 mm All prices are net plus the currently valid statutory VAT and shipping costs. The images may show the machine including optional accessories that are available at additional cost. If you are interested, please feel free to contact us. We are happy to offer professional, non-binding advice. The European Commission provides a platform for out-of-court online dispute resolution (ODR platform). This offer is intended solely as an online presentation of our goods. Contract negotiations are conducted via telecommunication (email, telephone, messaging portal). In the first step, we will make you a non-binding offer, which will also include information about our general terms and conditions, company details, and your right of withdrawal, before any purchase or contract is concluded.

Condition: new, Year of construction: 2026, Take advantage of our range of plastic grinding media for processing softer materials such as brass, copper or aluminium. Plastic grinding media provide a gentler and more delicate surface treatment. Like ceramic media, our plastic grinding media are available in a wide variety of grit grades, shapes and sizes. We work closely with you to select the optimal media for your specific workpieces and process requirements. Overview of the different shapes and their characteristics: - Cones (K): Have a high specific weight, ensuring effective material removal. Their rounded shape offers gentle processing. - Pyramids (P): Their edges make them particularly suitable for deburring operations. The pointed shape allows access to hard-to-reach areas such as bores. - Tri-Prongs (DZ): Excellent for processing complex components such as gear parts or workpieces with grooves. - Paraboloids (PA): Similar to cones, their rounded form is ideal for smoothing and polishing. Workpieces are treated softly and uniformly. - Lenses (L): Due to their lower weight, they are suitable for soft materials, offering gentle and even material removal. - Wedges (K): The versatile geometry makes them ideal media for deburring. The sharp point accesses narrow or hard-to-reach slots. - Tetrahedrons (T): Like pyramids, their edges enable efficient deburring. Tetrahedrons, however, have more sharply tapered corners, making them better suited for complex geometries. If you are interested, we look forward to hearing from you. We will be pleased to offer you advice, obligation-free. The European Commission provides a platform for out-of-court online dispute resolution (ODR platform). Kljdpfx Adjx A Eq Dodsl This offer serves exclusively as an online presentation of our products. Contract negotiations are conducted via telecommunications (e-mail, phone, messaging portal). As a first step, we will provide a non-binding quotation, along with our general terms and conditions, legal notice, and your right of withdrawal before any purchase or contract is concluded.

Condition: new, Year of construction: 2026, Machine type: YE 200 Manufacturer: ERBA Power kW: 2 x 0.3 Klodjx Aqvxepfx Addjl Total volume: 200 lt Description: The ERBA Separation Unit YE 200 is used for separating workpieces from abrasive media. Two motors provide the necessary movement of the screen. The YE 200 can be operated as a standalone machine or integrated with other systems, such as the ERBA Turbo (centrifugal finishing unit). The separation deck can be quickly and easily changed as required. Optionally, a frequency inverter can be installed, allowing stepless adjustment of motor speed. The stated price is net, plus the currently applicable VAT and shipping costs. The pictures may show the system including accessories, which are optionally available at additional cost. The price quoted refers to the base machine only. Sample photos are used. Actual appearance and dimensions may differ from the images. If you are interested, we look forward to hearing from you. We are happy to provide you with non-binding advice. The European Commission provides a platform for extrajudicial online dispute resolution (OS platform). This offer serves solely as an online presentation of our goods. Contract negotiations are concluded via telecommunications (e-mail, telephone, messaging portal). In the first step, we will make you a non-binding offer, in which we will also inform you about our general terms and conditions with legal notice and the right of withdrawal, before any purchase/contract is concluded.

Condition: new, Year of construction: 2026, Machine type: EVT 80 Manufacturer: ERBA Power kW: 0.75 Total capacity: 80 liters Description: The EVT 80 long-tub vibratory finishing machine from ERBA features a durable, hot-cast polyurethane lining. Discharge and separation are carried out via bottom discharge, which can be operated manually or pneumatically. Removable partition walls allow division of the processing tub into compartments for individual part processing. The machine is equipped with an electric control cabinet, and can optionally be fitted with a fully automatic PLC process controller. On request, a reinforced suspension and a more powerful motor can be installed for heavier workloads. The motor speed can be continuously adjusted using a frequency inverter (optional). Kodpfx Adex Aqxgjdoll The stated price is net, plus the currently applicable statutory VAT and shipping costs. Photos may show the system with accessories, which are optionally available and subject to additional costs. The price applies to the base machine. The photos are for illustrative purposes; actual appearance and size may vary from the pictures shown. If you are interested, we look forward to hearing from you. We are happy to provide you with consultation, without obligation. The European Commission provides a platform for online dispute resolution (ODR). This offer is solely for presenting our products. Contract negotiations are conducted via telecommunications (email, telephone, messaging portal). In the first step, we will send you a non-binding offer, which also includes our general terms and conditions with legal notice and information on your right of withdrawal, before any purchase or conclusion of contract takes place.

Condition: new, Year of construction: 2026, functionality: fully functional, air demand: 1.13 m³/h, pressure: 7 bar, warranty duration: 24 months, total width: 1,370 mm, total height: 2,080 mm, total length: 1,150 mm, overall weight: 350 kg, Equipment: cabin, lighting, The Vapormatt PUMA is a high-quality and versatile manual wet blasting cabinet from Vapormatt, the leading company in the wet blasting sector and the inventor of this technology in the 1950s. Over more than 70 years of development, Vapormatt has engineered the PUMA to be both ergonomic and efficient. With an optional insertable basket, small batch parts can be processed, and a clamping device enables easy handling of rims or wheels. Large workpieces weighing up to 125 kg can also be placed on the robust stainless steel grid. For easier operation, an optional stainless steel rotary table is available. The integrated recirculating water system with cascade tank, filter unit, and return pump ensures efficient use of water and blasting media. Compared to sandblasting, wet blasting allows for gentler and more uniform processing, thanks to water as the carrier medium. This technique enables you to achieve smooth and consistent surfaces on your parts. Technical data: - Internal dimensions: 1100 x 1100 x 1200 mm (LxWxH) - External dimensions: 1400 x 1200 x 2100 mm (LxWxH) - Pump output: 2.2 kW (400 V / 50 Hz) - Sump volume: approx. 142 L water / approx. 15–40 kg abrasive media - Work surface load capacity: 125 kg Prices are net plus the current applicable statutory VAT and shipping costs. The images may show the machine including optional accessories, which are available at additional cost. If you are interested, we look forward to hearing from you. We are happy to provide professional and non-binding advice. The European Commission provides a platform for extrajudicial online dispute resolution (the OS platform). Klsdstqmh Eopfx Addjl This offer serves exclusively as an online presentation of our products. Contract negotiations are conducted via telecommunication (email, telephone, online messaging platform). In the first step, we will provide you with a non-binding offer, together with information about our general terms and conditions with legal notice and your right of withdrawal, before any purchase or conclusion of contract takes place.

Condition: new, Year of construction: 2026, The ERBA EVP-RA 350 vibratory finishing machine features a rising, sloped process bowl floor with integrated separation. It is equipped with an easily replaceable screening unit and offers high operational efficiency thanks to the built-in drop step. Discharge and separation are carried out via the integrated flap (manual or pneumatic operation). Upon request, a reinforced suspension and a more powerful motor can be installed for higher loads. The motor speed can be continuously adjusted using a frequency inverter (optional). The EVP-RA 350 can be linked with other machines via its side discharge port. The system can be equipped with a fully automatic PLC control system (optional). ERBA vibratory finishing systems are distinguished by their durability and long service life, based in part on the hot-cast polyurethane lining of the process bowl. Technical data: - Gross volume: 385 liters - Channel width: 340 mm - Vibration motor power: 2.2 kW - Speed: 1,400 rpm Kedpfen Ut Urox Addell - Inner bowl diameter: 1,200 mm All prices are net, excluding the currently applicable statutory VAT and freight costs. Some images may show the machine with accessories that are available as options and subject to additional charges. If you are interested, please contact us. We would be happy to advise you without obligation. The European Commission provides a platform for out-of-court online dispute resolution (ODR platform). This listing serves solely as an online presentation of our products. Contract negotiations are conducted via telecommunications (e-mail, phone, or messaging portal). You will first receive a non-binding offer from us, which will also provide information about our general terms and conditions, legal notice, and your right of withdrawal before any purchase or contract is concluded.

Condition: used, Year of construction: 2018, 1 x CNC-CONTROLLED DRILLING, GLUING AND DOWEL INSERTING MACHINE GANNOMAT "INDEX 130 PRO" (with options as Index 180 Pro) 400V, 3Ph, 50Hz complete in standard design with: - Support with linear guide consisting of: 1 x single-spindle horizontal drilling unit, 1.1 kW motor, tool speed selectable via operator software (3000/5000/8000 rpm) 1 x blow-out, gluing and dowel inserting station in reinforced design for dowels Æ 8 mm, dowel length 30 mm - fully automatic, electronically controlled central lubrication - X-axis NC controlled, with working length 1300 mm, travel speed max. 78 m/min. - Z-axis, position via support table 5-40 mm programmable with NC-controlled Z-axis option - Dowel driving overhang of 7-20 mm, programmable with NC-controlled Y-axis option, drilling depth of 0-35 mm (with drill length GL 70 mm) is automatically set with driving overhang - Closed glue system with 6 bar glue pressure via glue nozzle, for glues with a viscosity of 150 to 350 mPas - Glue quantity continuously adjustable via operator software - GL/WATER selector switch for rinsing the glue system, 1 stainless steel container each for 5 kg glue and 5 l water - Control lamp for residual glue quantity display in the glue container - 1 side stop left, 1 side stop right and 1 center stop (all removable) - 4 start buttons for individual working with 1-4 workpieces - 4 pcs. Pneumatic inclined clamping cylinder 10° for workpiece thicknesses up to max. 80 mm, workpiece length (Y) min. 70 mm - 1 pc. suction funnel, connection Æ 80 mm - 1 pc. TCT control with: built-in industrial PC, incl. Soft PLC type Beckhoff TWINCAT, operating temperature range 0-50°C, TFT industrial display 15" resistive touchscreen, resolution 1024 x 768, CPU 2 GHz, 256 MB RAM, 2x network interface adapters, IDE hard disk, 4x USB rear, 1x USB front, operating system: WINDOWS 7 - programming via menu-driven user software, drilling distances freely programmable with ABSOLUTE, RELATIVE or GRID dimensioning, automatic workpiece mirroring and work step optimization, 4 work fields can be assigned with different programs, graphic workpiece display, parametric programming, 0-point shift, programmable work lists, error diagnosis with plain text OPTIONS: 1 electronic, optical glue monitoring system G.I.C. (Glue Insert Control) for 1 glue nozzle 4 vertical inclined clamping cylinders 10° with holder, additionally, (total 8 clamping cylinders) 1 surcharge for machine bed length 1800 mm with working length 1800 mm 1 surcharge for: 1 horizontal drilling unit, motor 1.5 kW, with multi-spindle drilling head with 3 individually controllable drilling spindles, pitch 32 mm arranged in X-axis, tool speed 3000 rpm. (The standard working length is not reduced) 1 Y-axis NC-controlled, with recirculating ball screw and dynamic traversing speed of 300 mm/sec. The dowel driving overhang 7-30 mm and the drill hole depth 0-42 mm can be programmed via software. (with drill length GL 77 mm) for vertical drilling unit drilling from TOP, Y-axis position 5-42 mm 1 surcharge Y-axis NC-controlled position 5-62 mm instead of 5-42 mm 1 surcharge for: 1 vertical drilling unit drilling from TOP, motor 1.5 kW, with multi-spindle drilling head with 3 individually accessible drilling spindles, 32 mm pitch arranged in X-axis, tool speed 3000 rpm. Y-axis position 5-42 mm, workpiece length (Y) min. 130 mm, (the standard working length is not reduced) 1 Z-axis NC-controlled, with K Kodpfoxwaz Hex Addsll

Condition: new, Year of construction: 2025, CONDOR VC plus The new dimension in conventional precision lathes. A high-quality, powerful and energy-efficient precision lathe for the highly productive area of production and toolmaking, but also for training and further education High-quality, energy-efficient, precise and universally applicable in production, training and further education. It impresses with: future-oriented technology maximum accuracy durability user-friendly ergonomics minimum space requirement and a wide range of accessories. The consistent and innovative further development of the tried-and-tested Condor series is the economical and intelligent solution for your daily applications. Technical data: WORKING AREA Center height 180 mm Swing diameter over bed 360 mm Swing diameter over facing slide 190 mm Center width 800 mm TURNING SPINDLE Spindle head DIN 55027/DIN ISO 702-3 size 6 Spindle bore 57 mm Spindle diameter in front bearing 90 mm MAIN DRIVE Drive power 60 %/100 % ED - / 10.5 kW Speed range 25 - 4,000 min-1 Number of speeds infinitely variable FEED RANGE Number stepless Longitudinal 0.01 - 6 mm/rev Plan 0.003 - 2 mm/rev THREAD CUTTING RANGE Metric thread 0.1 - 20 mm REITSTOCK Quill diameter 50 mm Quill stroke 110 mm Internal taper DIN 228 MK 3 ACCEPTANCE ACCURACY DIN 8605 Equipped with WEILER WTS 15 VC plus screen display - Large, clearly arranged 15" touch screen, rotatable and tiltable, resolution 1366 x 768 - Change of operating screens via swipe movements - Operating functions can be called up via app manager - Control panels can be freely configured, Klsdpfx Adeqwipnjdjl placed and scaled as required - Drawings / sketches can be imported from PDF files Can be zoomed individually via USB interface - Video-supported maintenance of the machine - Context help menu (instead of screen display WEILER VC plus) The machine is located in our showroom in 71334 Waiblingen-Beinstein and is available immediately. Please contact us regarding equipment.

Condition: new, Intern VC plus The new dimension in the field of conventional precision lathes. High-quality, energy-efficient, precise and universally applicable in production, training and further education. It convinces through: future-oriented technology highest accuracy durability user-friendly ergonomics smallest footprint and extensive accessories. The consistent and innovative further development of the practice-proven Praktikant series is the economical and intelligent solution for your daily applications. Technical data: WORKING RANGE Center height 160 mm Swing over bed 320 mm Swing over cross slide 190 mm Center width 650 mm ROTATING SPINDLE spindle head DIN 55027/DIN ISO 702-3 size 5 spindle bore 43 mm Spindle diameter in front bearing 70 mm MAIN DRIVE drive power 60 %/100 % ED - / 8 kW speed range 25 - 5.000 min-1 Number of speeds stepless FEED RANGE Number stepless longitudinal 0.01 - 6 mm/rev plane 0.003 - 2 mm/rev THREAD CUTTING RANGE Metric thread 0.1 - 20 mm REITSTOCK quill diameter 40 mm quill stroke 85 mm Inner taper DIN 228 MK 3 Kodpfx Aohw N Ntsddell ACCEPTANCE ACCURACY DIN 8605 Equipped with WEILER WTS 15 VC plus screen display - Large, clear 15" touch screen, rotatable and tiltable, resolution 1366 x 768 - Change of operating screens via swiping movements - Operating functions can be called up via App Manager - Control panels can be freely configured,