Used Scrapers for sale (675)

Condition: good (used), functionality: fully functional, We offer a used Liebherr scraper, semi and fully automatic. Dodpfx Asrpmlrenfscg Fully functional, with control system.

Year of construction: 2011, condition: used, functionality: unexamined, Scraper conveyor for sale. The conveyor consists of two sections – a horizontal and an inclined part. Length of the horizontal section: 6,870 mm, length of the inclined section: 5,120 mm, outer width: 1,580 mm, outer height: 1,780 mm, inner width: 1,270 mm, inner height: 1,090 mm, drive motor: 5.5 kW, slat pitch: approx. 280 mm. The conveyor is dismantled and ready for transport. The machine can be inspected at: Sępólno Krajeńskie, Kuyavian-Pomeranian Voivodeship, Poland. Dcedpfx Answxb Tpefog

Condition: used, Wood chip screening plant Chip screening plant Width 1,9m Length 5.3m Height 0.8m 1st grid 40x40mm 2nd grid 15x15xmm Dcodpfstxblkex Anfog Double scraper for screening system Total length 7.5m (2m straight, 5m upwards) Outer flange width 760x610mm Scraper width 400mm + 250mm Gear motor 4 kW Speed 39 rpm

Condition: ready for operation (used), Year of construction: 2009, machine/vehicle number: 26, functionality: fully functional, operating hours: 2,216 h, total height: 1,700 mm, total length: 6,100 mm, total width: 1,450 mm, overall weight: 2,500 kg, Equipment: CE marking, TECHNICAL DETAILS The machine has the following configuration: Pre-milling unit (tools included) Gluing unit (tools included) End trimming unit (tools included) Rough milling unit (tools included) Corner rounding unit (tools included) Radius scraper unit (tools included) Flat scraper unit (tools included) MACHINE DETAILS Power consumption: 39.5 A Voltage: 400 V Fuse: 50 A Dimensions & Weight Dodpfx Ansy Nxz Sefscg Dimensions (L x W x H): 6,100 x 1,450 x 1,700 mm Weight: 2,500 kg Operating hours: 2,216 h EQUIPMENT CE marking

Condition: used, Used Becomix model Beco Mini RW 2.5 lab scale homogenising mixer.  Manufacturer: Becomix. Capacity: Working capacity 0.5-3.5L. Dimensions: 800mm x 800mm x 900mm high. Dcedeyx Ibgepfx Anfsg Also includes: -Integrated CIP system. -Agitator with scrapers. -Intuitive touch panel PLC control.  -Compact device with tempering unit. -Vacuum pump. - PLC control integrated into a mobile table. -Mixing vessel full vacuum to 1 bar, double jacket 4 bar.

Condition: reconditioned (used), Year of construction: 2014, functionality: fully functional, workpiece height (max.): 80 mm, edge thickness (max.): 15 mm, height adjustment type: electric, overall weight: 7,000 kg, year of last overhaul: 2023, compressed air connection: 6 bar, power of the milling unit: 3,000 W, space requirement length: 10,500 mm, Fully refurbished Topedge Duo-melt, year 2014 2 x 3Kw each Pre-milling motors 80 mm panel thickness 1 x Synchroflex top driven belt system 2 x Glue heads and tanks, Duo Melt system (For instant glue colour changes) 1 x rough trim station 1 x Bevel fine trim (can also be used for fine finishing wood in “flat” setting - adjustable angle 1 x Radius trimming machine 1 x AKF station 1 x 4 position per side AZK4 radius scraper 1 x Flat scraper Dodpfx Anox Nbprjfocg 1 x Cleaning spray, front, middle and back - LCM 1 x Buffing station 2 x free spaces Infeed fence alignment for narrow panels Nesting package LCM iRelease cleaning system BrushTec ES - not included

Condition: used, capacity 1.000L. all stainless steel double jacket 36 kW tiltable drum stirring system with scrapers electric heating Djdpfjy Nawhox Anfscg dimensions (l x w x h) : ± 1.900 x 1.900 x 1.800 mm

Condition: ready for operation (used), Year of construction: 2011, functionality: fully functional, operating hours: 1,651 h, workpiece height (max.): 60 mm, edge thickness (max.): 3 mm, feed rate X-axis: 25 m/min, HOMAG KAL 310 + panel return system TFU 140! TECHNICAL DETAILS Profile milling unit FK11 manual Edge thickness: max. 3 mm Motors: 2 units Motor power: 0.4 kW per motor Frequency: 200 Hz Speed: 12,000 rpm Feed speed: max. 20 m/min Feed speed for continuous trimming without profile trimming: max. 30 m/min Dedpfx Asyzxa Esnfecg Panel length single-sided: min. 240 mm Panel length double-sided: min. 120 mm Panel thickness: 12 - 60 mm Panel spacing with PC22: min. 500 mm Minimum workpiece gap for workpiece thickness over 22 mm: min. 600 mm Multi-scraper MN21 Automatic Number of profiles: max. 5 different profiles Edge thickness: max. 3 mm Panel thickness for radius R = 3 mm: min. 13 mm Panel thickness for bevel 0.5 x 45°: min. 10 mm TC knives: 2 units Bevel angle: 20° Radius: R = 1.5 / R = 2 / R = 3 / R = 5 Pre-milling unit BF10 Motors: 2 units Motor power: 0.55 kW per motor Frequency: 200 Hz Speed: 12,000 rpm Swivel range: +/- 1° TC cutter: 70 x 25 mm HSK: 25 Cutting angle: 54° Feed speed: 18-25 m/min Workpiece thickness: 8-60 mm Edging material (roll): 0.3-3 mm MACHINE DETAILS Operating hours Operating hours: 6,358 h Feed time: 1,651 h EQUIPMENT Pre-milling Automatic adjustment of the infeed fence Infeed device with 2 rollers Quickmelt application station 2-roller magazine infeed Automatic adjustment of the pressure zone HL84 end trimming unit with pneumatic adjustment BF10 flush milling unit with pneumatic adjustment FK11 profile milling unit MN21 multi-profile scraper unit for 5 different profiles Grooving unit Glue joint scraper Buffer Return system TFU140

Condition: excellent (used), Year of construction: 2014, Ref:11081 . 2014 Kolbus DA-270 Casemaker For high-speed production of hard book covers, Lever Arch files and games boards. Comprising: ‘Co-pilot’ system with touch screen for automatic size setting, menu guided make-ready and fault indication. Twin board magazine feeders Central soft spine feeder with double reel holder for auto-splice and cutter for waste *Special board centre strip cutting device Magazine feeder of pre-cut cloth with miss control Mobile hot-melt gluing unit with pre-melter* Heated glue application roller with scraper roller Cloth cylinder with grippers & exchangeable plates for rubber pad Counter shingle delivery with roller conveyor External glue application adjustment Glue viscosity device for automatic water supply control Pressing roller for crease-free cover to board application Single case request for operator set-up Variable DC drive Automatic lubrication Including accessories & manuals. N.B. Compressed air and water supplies to client’s account. Accessories: Board centre-strip cutting device for cutting rigid centre board strips to width, with possible width variance from product to product for digital book production. ° Board sheet thickness max. 2 mm ° Width max. 1,500 mm | height min. 140 mm | max. 390 mm Dcjdpfsyzy Rrox Anfeg ° Board centre-strip max. 7 mm | max. 60 mm Kolbus ECK standalone corner cutter to work with case maker Specification: Size of opened case, Max: 670 x 390 mm Min : 205 x 140 mm Centre strip width : 6 - 90 mm, thickness 1 – 4 mm Joint width : 4 - 15 mm Turn-in width, closed : 8 – 15 mm Output, variable : up to 65 cycles/min Floor space : L: 6700 x W: 3000 x H: 2,200 mm Electrical loading : 15 kW (3ph, 400V, 50 Hz) Air requirement : 33 Nm3/h 6 bar.

Condition: new, Year of construction: 2025, cutting diameter 335 mm saw band length 4400 x 34 x 1.1 mm table height 750 mm feed 5.0 - 2300 mm pro Hub capacity 90 degrees: flat 500 x 335 mm capacity 45 degrees: round 330 mm capacity 45 degrees: flat 320 x 335 mm capacity 45 degrees: round links 305 mm capacity 45 degrees: flat links 305 x 335 mm capacity 30 degrees: round 180 capacity 30 degrees: flat 170 x 335 15 - 150 m/min workpiece weight max. 250 kg/m 3.0 kW 2550 kg 4350 x 2300 x 1900 mm - The ergonomic panel control can be networked and offers various option packs * Teleservice for remote maintenance * Setting of sawing programs in the AV * Import of saw programs from CAD with DSTV interface and data export - Automatic material feed: Dcsdpfx Aeulnb Djnfsg - In a compact design for shorter sections or with flexible insertion tongs available in almost all lengths - Exact positioning of the material using servo positioning technology - Forward-looking electric saw feed with ball screw: highest Cutting performance and quality, while being gentle on the saw blade - Consistent use of the most modern recirculating ball guides: smooth-running, highly resilient, low-maintenance and backlash-free - Unique and patented double miter system: material is always stretched at right angles - Insertion tongs can be extended as required in 1000 mm increments Furnishing: - Automatic cutting pressure and feed monitoring - Frequency-controlled AC drive 15-150 m/min, 3 kW - Hydraulic material full stroke clamping - Automatic movement of the vice - Automatic saw frame height adjustment - Minimum speed and saw band monitoring - Electric miter swiveling via servo motor - Visualized program input with CNC control - Integrated MEBA tong insertion system from 5-2300 mm per stroke with integrated roller conveyor *Optional equipment: - Laser light for cutting line indication/scribing saws - Driven chip brush - Micro dosing system - Job menu - MEBA NC Server comfort package - Scraper belt conveyor for optimal chip disposal, 2000 mm length - Installation elements (4 pieces) - Adjustable deflector plate 335 DGA

Condition: used, Year of construction: 2012, total height: 1,600 mm, total length: 5,250 mm, total width: 1,440 mm, Edgebander HEBROCK AKV 3006 DK FS maximum edge thickness 3/8 mm min/max. workpiece thickness 10/40 mm min. workpiece length approximately 200 mm min. workpiece width approx. 80 mm feed speed about 10 m/Min. ready in about 6 minutes. maximum power consumption 12 kW electrical connection 400 V / 3 Ph / 50 Hz Pre-mill Glue unit Pressure roller Chopping saw Milling unit Milling unit Corner rounder Dcjdpfx Anjwnhb Sjfeg Radius scraper Flat scraper Cleaning unit Dimensions (length x width x height) 5250x1445x1600 mm, weight 1550kg - Year: 2012 - Documentation available: No - CE certificate present: No - Transport dimensions: 5250mm x 1445mm x 1600mm (l x w x h) Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 2015, machine/vehicle number: 100007528, functionality: fully functional, power: 13 kW (17.68 HP), type of input current: three-phase, total height: 1,700 mm, total length: 9,000 mm, total width: 3,000 mm, Biesse Akron 1440 A With Automatic Return Table And Conveyer, PUR Glue Pot NC Controlled , Pre miller, fence, Radius Trimmer And Scraper. Edging Thickness Selectable From Pc with automatic Setting Dcsdpfxoxmi E Ho Anfsg Delivery can be arrange in the Republic of Ireland

Condition: used, Year of construction: 1994, punching force max. 50 t throat 510 mm stroke 32 mm stroke - stepless adjustable 10 - 32 mm no. of strokes 35 bei 10 mm Hub/min Working height 1070 mm daylight 350 mm table width 255 mm dimensions ca. 1080 x 650 x 1680 mm material layer 630 X 535 Dsdpjyrhyuofx Anfecg weight ca. 1400 kg Scraper, height-adjustable and removable, with interchangeable plate Hydraulic low-pressure finder for foot switch operation Two-stage foot switch and electrical controls Integrated hydraulic unit With punching saddle for dies no. 3, up to Ø 32.5 mm Quick-change device for punches 2 and 5 up to Ø 31.5 mm Peddinghaus blue series with material support table no. 513, dimensions 630 x 535 mm

Condition: reconditioned (used), Technical data feed hopper with hydraulic moving floor and bag opener for recyclables from yellow bags and residual waste: Manufacturer BRT HARTNER GmbH Type HP5-3035 Year of construction 2015 Hopper volume 30 m³ Drive line 17.5 kW Dimensions in current state 13,200 x 3,050 x 4,350 mm (l x w x h) Condition of the machine: The feed hopper with bag opener was used at a large recycling plant, where recyclable materials from yellow bags or commercial waste were tipped into the hopper using wheel loaders, the bags were opened using the bag opener, and the recyclable materials were transported to a sorting plant or the commercial waste was transported in measured quantities for further processing. The system functioned flawlessly until it was dismantled and replaced with a larger system with higher throughput capacity. The machine was dismantled into individual parts in our workshop, partially overhauled, reassembled, and tested during operation. The following overhaul work was carried out and the following spare parts were replaced: Dismantling of the feed hopper and bag opener into individual parts. Cleaning, partial sandblasting, priming and painting of the steel parts. Various wear and cover plates were newly manufactured and installed. Cutting off the worn ends (approx. 40cm) of the push floor pipes. Welding on the new pipes and smoothing the push floor pipes. Replacement of all plastic sliding plates for the hydraulic push floor. Removal of the hydraulic unit from the push floor, emptying of the hydraulic oil tank, replacement of the oil filters, refilling with new hydraulic oil. Replacement of the three hydraulic blocks, all valves, the oil sight glass and all hydraulic hoses from the hydraulic unit. The seal kit and hydraulic hoses were replaced on all three hydraulic cylinders of the push floor. All six limit switches (proximity sensors) on the push floor were replaced. The conveyor chains on the left and right of the scraper conveyor were replaced. Seven carrier bars on the scraper conveyor were replaced. The drive motor for the ripper blades was replaced. All nine pneumatic cylinders for the pressure pipes were replaced. All pneumatic lines and connections were replaced. All of the plastic sliding plates for the hydraulic operation of the bag opener were replaced. The bag opener can be moved vertically so that the system can also be used for commercial waste or residual waste without the bag opener. The side impact protection plates on both sides were replaced. Various wear parts of the bag opener have been replaced. Dodpfjyizxrex Anfjcg The entire system has been rewired and reconnected. The system control in the control cabinet has been retrofitted by the manufacturer BRT Hartner to a self-sufficient individual control system and the standard programme has been reloaded into the control system. The system has been commissioned and tested by the manufacturer BRT Hartner, see the function video. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, year of last overhaul: 2024, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the turbulator replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Dodpfx Anou Thhrjfocg Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: used, Year of construction: 1994, Used machine Year of manufacture: 1994 Condition: as is/was in production until recently Equipment and technical data: Glue application unit with glue pot and applicator roller Pressing station Cut-off unit with linear guides Flush trimming unit with horizontal and vertical sensing with 200 Hz motors swivelable 0 - 30° with radius scraper with buffing unit Edge thickness 0.4 - 5 mm Coil separation 0.8 x 60 or 3 x 30 mm Workpiece width min. 55 mm Workpiece length min. 160 mm Workpiece thickness 10 - 55 mm Feed rate 11 m/min Pneumatic connection 6 bar Dimensions 3855 x 1000 x 1610 mm Extraction connection 100 mm Dcsdpfx Ajy Nuhbsnfsg Weight 1000 kg Availability: approx. June 2026 Location: Baden-Württemberg

Condition: new, Year of construction: 2024, New machine Year of manufacture: 2024 (arrived 2025) MACHINESEEKER ENQUIRIES: Please understand that we do not offer this new machine outside our sales territory in Germany (Rhine-Main area and North Rhine-Westphalia). Such enquiries will not be answered. Technical specifications: Edge thickness, coil material: 0.4 – 3 mm (material dependent) Edge thickness, strip material: 0.4 – 8 mm (material dependent) Edge cross-section: max. 6 x 42 mm Edge height: max. 65 mm Workpiece thickness: 6 – 60 mm (restrictions possible for certain units) Workpiece width: min. 65 mm Workpiece length: min. 160 mm (without corner copying) Workpiece length: 180 mm Dcedpsy Nuf Tjfx Anfjg Feed speed: 10 m/min Configuration: - Motorised pressure bridge adjustment - Pull-out workpiece support XL, spacing 600 mm - LED light at infeed, 3-colour - Motorised infeed fence adjustment - Extended infeed fence, 1,252 mm - I-Tronic package - Edge Control PPC 322 W controller - IntelliSet: intelligent tool offset - f.a.s.t = fast setting technology - ECO-Mode energy saving function - Prepared for RETURN connection (third-party product) - BS 501 guiding system; precise right-angle workpiece feed for edgebanding of narrow parts on end grain - Workpiece thickness: min. 10 mm - Workpiece width: min. 60 mm - Workpiece length: approx. 140 – 450 mm - FG201 jointing unit with 2 milling heads, 64 mm high - MG 301 edge feeder - GluJet GJ 725 NC PUR PRO glue application system - Automatic glue height adjustment via dosing sleeve and sensing nozzle to compensate for panel tolerances - NC axis for height adjustment - 90° swivelling for easy cleaning of the Glue Jet nozzle - Includes vacuum pump for professional processing of PUR adhesives. The vacuum pump removes the reaction partner (water molecules) from the PUR, allowing uncured PUR adhesive to remain in the system. The pump operates independently of the machine’s power supply and automatically compensates for vacuum loss. - Full control of PUR! - DW 301 pressure unit with motorised NC axis; first roller driven with pneumatic plunge control, 2 conical follow-up pressure rollers - GM301 spray unit after pressure section for high-gloss edges (slip agent) - KA 501 end trimming unit, pneumatic (60 mm) - Extraction hoods for end trimming unit - FR301 MOT6 multifunction milling unit - Shelf program - FF 301 MOT1 profile milling unit - ZK301 MOT4 scraper unit incl. high-gloss kit - FK702 surface scraper - Spray unit for separation and cleaning agent, complete - GM 301 spray unit after pressure section (high-gloss edges) - SW 501 buffing unit Piping above the machine is not included in the scope of delivery. Availability: short notice Location: Hochheim

Condition: like new (used), Year of construction: 2020, functionality: fully functional, operating hours: 1,500 h, USED Akira Seiki 1600XP Fanuc 0iMF Open Fronted Vertical Machining Centre with Fanuc Ex Stock - Subject to Prior Sale. YOM 2020, Machine with Very Low Hours Usage. Approx 1500 Hours  12,000 RPM Spindle with Refrigeration System  36 Station Arm Type ATC  Full Splash Guard Dcedpfju A U Nksx Anfog  Fully Integrated Detron GXA-255h 4th Axis Nc Rotary Table with SR255H Tailstock Support Unit  Chip Conveyor & Chip Bin (Scraper Type)  Chip Flushing System Including Coolant Wash Gun  Through Spindle Coolant System - 35 Bars with Filter  Fanuc Memory Extension - 2 Mb  Fanuc 10.4 “ Screen with Manual Guide-I  Coolant Tank Capacity - 640 Litres  THK Heavy Duty Linear Guideways  Manual Pulse Generator  3 Colour Signal Lamp  Automatic Lubrication System  Rigid Tapping & Helical Interpolation Function TABLE Working Surface 1,750 X 800 MM Tee Slots 18 x 125 x 6.0 MM Spindle Nose to Table 100 ~ 915 MM Spindle Centre to Column 865 MM Table Load Capacity 2,300 KGS TRAVEL X-Axis Travel 1,630 MM Y-Axis Travel 850 MM Z-Axis Travel 815 MM SPINDLE Spindle Nose Taper BT-40 Spindle Speed - Max 12,000 RPM FEED Rapid Traverse (X & Y-Axis) 33 M / MIN Rapid Traverse (Z-Axis) 25 M / MIN Cutting Feedrates - Max 12 M / MIN ACCURACIES Positioning 0.01 MM Repeatability + - 0.003 MM ATC Tool Storage Capacity ARM TYPE - 36 STATIONS Maximum Tool Weight 7.0 KGS Tool Diameter - Max 75 MM Tool Length - Max 250 MM Tool Shank BT-40 Tool Exchange Time 2.2 SEC MOTOR Spindle Drive Motor (FANUC) 18.5 KW POWER SUPPLY Voltage 415V / 3PH / 50HZ Power Requirement 30.0 KVA MACHINE DIMENSIONS Machine Floor Space Requirement 4,820 x 3,576 MM Machine Weight 12,600 KG

Condition: like new (used), Year of construction: 2020, functionality: fully functional, operating hours: 1,500 h, USED Akira Seiki 1600XP Fanuc 0iMF Open Fronted Vertical Machining Centre with Fanuc Ex Stock - Subject to Prior Sale. YOM 2020, Machine with Very Low Hours Usage. Approx 1500 Hours  12,000 RPM Spindle with Refrigeration System  36 Station Arm Type ATC  Full Splash Guard  Fully Integrated Detron GXA-255h 4th Axis Nc Rotary Table with SR255H Tailstock Support Unit  Chip Conveyor & Chip Bin (Scraper Type)  Chip Flushing System Including Coolant Wash Gun  Through Spindle Coolant System - 35 Bars with Filter  Fanuc Memory Extension - 2 Mb  Fanuc 10.4 “ Screen with Manual Guide-I  Coolant Tank Capacity - 640 Litres  THK Heavy Duty Linear Guideways  Manual Pulse Generator  3 Colour Signal Lamp  Automatic Lubrication System  Rigid Tapping & Helical Interpolation Function Dedeq Nmm Tepfx Anfocg TABLE Working Surface 1,750 X 800 MM Tee Slots 18 x 125 x 6.0 MM Spindle Nose to Table 100 ~ 915 MM Spindle Centre to Column 865 MM Table Load Capacity 2,300 KGS TRAVEL X-Axis Travel 1,630 MM Y-Axis Travel 850 MM Z-Axis Travel 815 MM SPINDLE Spindle Nose Taper BT-40 Spindle Speed - Max 12,000 RPM FEED Rapid Traverse (X & Y-Axis) 33 M / MIN Rapid Traverse (Z-Axis) 25 M / MIN Cutting Feedrates - Max 12 M / MIN ACCURACIES Positioning 0.01 MM Repeatability + - 0.003 MM ATC Tool Storage Capacity ARM TYPE - 36 STATIONS Maximum Tool Weight 7.0 KGS Tool Diameter - Max 75 MM Tool Length - Max 250 MM Tool Shank BT-40 Tool Exchange Time 2.2 SEC MOTOR Spindle Drive Motor (FANUC) 18.5 KW POWER SUPPLY Voltage 415V / 3PH / 50HZ Power Requirement 30.0 KVA MACHINE DIMENSIONS Machine Floor Space Requirement 4,820 x 3,576 MM Machine Weight 12,600 KG

Condition: excellent (used), Edge Banding Machine HEBROCK K36 Airtronic -used- - PC control with display - Touchscreen - Swiveling control panel - Program memory - Automatic pressure bridge adjustment - Feed via transport chain - Extendable workpiece support - Motorized adjustable infeed fence - Diamond jointing cutter, both with and against feed direction - Quick heating gluepot - Gluepot change system - Suitable for PUR adhesives - Cross-cut saw with HF motor - Flush milling unit Dedpfxoymyp Rs Anfocg - Flush, radius, and chamfer milling unit - Pneumatic changeover of milling unit - Multi-milling tool - Multi-radius scraper blade - Chip collection box for radius scraper blade - Air jet nozzle at the radius scraper - Flat scraper blade - Air jet nozzle at the flat scraper - Exchangeable motor for corner rounding - Spray device for separator agent - Spray device for cleaning agent - Spray device for antistatic coolant - Spray device for lubricant - LED lighting in the machine area - Exchange gluepots - Zero Joint Airtronic System ----- Technical Data ----- - Edge thickness, coil material: 0.5-3 mm - Max. edge thickness for corner rounding: 3 mm - Workpiece thickness: 8-60 mm - Workpiece thickness for corner rounding: 45 mm - Min. workpiece length: 200 mm - Feed speed: 7-10 m/min - Support plate Ø for edge material: 850 mm - Guillotine for coil material up to: 3 mm - Jointing cutter power: 2x2.2 kW - Cross-cut saw power: 0.37 kW - Milling station power: 2x0.37 kW - Corner rounding unit power: 0.37 kW - Buffing unit power: 2x0.18 kW - Extraction port Ø jointing unit: 60 mm - Compressed air connection: 7 bar - Total length: 5,540 mm - Dimensions (LxWxH): 5,540x1,210x1,450 mm - Weight: 1,700 kg Quality Information: - All settings checked - Complete basic inspection - Complete basic cleaning - Electrical system checked - Pneumatics checked - Immediately ready for operation

Condition: good (used), Chip conveyor, chip conveyor belt, coolant cleaning, chip disposal, scraper conveyor, scraper conveyor belt, chip chain conveyor, hinge belt conveyor, scraper belt conveyor -Manufacturer: COMAR, chip conveyor comes from a MIKRON VC 500D -Type: VC 500D -Conveyor belt width: 230 mm -Outlet height: 1100 mm -Drive: 0.15 kW / 14 rpm (2.40 m/min) -Individual components: see photos -Dimensions: 720/2630/H1575 mm -Weight: 727 kg Dsdpfxsy Ezace Anfscg

Condition: ready for operation (used), Year of construction: 2005, operating hours: 16,700 h, spindle speed (max.): 6,300 rpm, total height: 2,750 mm, overall weight: 10,200 kg, travel distance X-axis: 800 mm, travel distance Y-axis: 700 mm, travel distance Z-axis: 600 mm, controller manufacturer: HEIDENHAIN, controller model: iTNC 530, spindle motor power: 16,000 W, product length (max.): 6,600 mm, table load: 600 kg, number of axes: 5, This 5-axis DECKEL MAHO DMU 80P hi-dyn was manufactured in 2005. It features impressive travels of 800 mm in X, 700 mm in Y, and 600 mm in Z. The machine is equipped with a Heidenhain iTNC 530 control and a maximum spindle speed of 6,300 rpm. If you are looking to get high-quality machining capabilities, consider the DECKEL MAHO DMU 80P hi-dyn universal machining centre we have for sale. Contact us for further details. Dedpfxjy I Aqus Anfecg • Spindle torque: 475 Nm (40% DC) • Tool changer: 60 positions (chain magazine) • Rapid traverse (X/Y/Z): 50 m/min • Feed rate (X/Y/Z): 50,000 mm/min • Table: NC swivel rotary table (d 630 mm) • Swivel range: -45° to +30° • Cooling: 40 bar internal coolant supply (IKZ) through spindle center • Power consumption: 50 kVA • Defect: Transmission damage Additional equipment • Chip conveyor: Scraper belt type, discharge height 956 mm Technical Specification Taper Size SK 40

Condition: excellent (used), Year of construction: 2004, Deckel Maho 3 axis vertical machining center in good condition with 15781 spindle hours. Dcjdpfjy H Hz Ijx Anfeg Well maintained by DMG services in the Netherlands. Immediately available for delivery. Viewing possible upon appointment. More info available on request. Cnc control Siemens Sinumerik 840D Number of axes 3 Maximum Reach X 2200 mm Maximum Reach Y 560 mm Maximum Reach Z 720 mm Maximum Clamping Height 600 mm Table Size (LxW) 2600x600 mm Maximum Table Load 2200 kg Guide Type Linear Max. Speed 18,000 rpm Max. Power 35 kW Tool Holder SK40 Tool Magazine Capacity 60 Tool Change Duration 9.6 sec Including: ELECTRONIC HANDWHEEL 18.000 RPM HEIDENHAIN MEASURING PROBE MODE 4 DIVIDING WALL CHIP CONVEYOR SCRAPER BELT TYPE IKZ WITH PAPER BELT FILTER BLOWN AIR THROUGH SPINDLE EXTERNAL COOLING OIL MIST SEPARATOR BREAK REMOVAL TOOL WITH LASER RESIN GUN NET SERVICE EXTENSION IBN NET SERVICE Optional: Large set of SK40 tooling and vises/clamping systems available. Please note: The information on this page has been obtained to the best of our ability and belief. This information is provided in good faith, but its accuracy is not guaranteed. Accordingly, this information is not binding and does not constitute a contractual condition. We recommend that you check all essential details during an inspection of the machine. To save unnecessary travel costs for our customers, in most cases we recommend organizing a live video inspection.

Condition: excellent (used), Year of construction: 2012, machine/vehicle number: 2418, functionality: fully functional, Availability: Mid-July 2026 The machine can be inspected and demonstrated at the customer's site. Last major inspection by "HEBROCK" in 8/2024 - Machine equipped with Pro-Face Panel touch control - Glue application via glue roller and granulate container Dcedpoy N U S Hefx Anfog - Quick-heating glue pot - 2 additional glue stations - Coil material 0.4 - 3 mm incl. automatic coil separation - Strip material max. 8 mm - Minimum workpiece width: 90 mm - Minimum workpiece thickness: 10 mm - Minimum workpiece length: 220 mm - Feed rate: 10 m/min - Jointing unit (counter-/co-rotation) with 2 DIA tools - Pressure unit with 4 pressure rollers - End trimming unit 0.37 kW, 15,000 rpm - Flush/chamfer/radius milling unit 2 x 0.37 kW, 15,000 rpm - Radius scraper unit - Corner rounding unit - Surface scraper unit - Buffing unit - "RIEPE" release agent spray unit - "RIEPE" cleaning agent spray unit - Extendable workpiece support - Chip collection box

Year of construction: 2016, condition: used, Manufacturer : IMMEQUIP Engineering Model : CEMH 360 Year: 2016 Width: 36 cm Type : Cutter / Laminator Structure & design: All-stainless steel 304L mechanically welded frame Fitted with 4 pivoting wheels with brakes Conveyor: Entry conveyor belt – Motor: 0.25 kW – three-phase 400V – Product guidance via stainless steel comb Conveyor: Outfeed belt – Motor: 0.37 kW – three-phase 400V – Integrated air blow-off ramp Cutting unit – Cutting wheel Ø350 mm – 3 blade holders (45° and 90°) – 3 ground hardened steel blades (Z30C13 – 40/42 HRC) – Option to add more – Rotation speed: 72 rpm – Motor: 0.37 kW – three-phase 400V – Guide with stainless steel bearings – Cutting kit available: 90° and 45° Product orientation kit: 1 symmetrical set, each comprising 1 cell, 1 stop flap and 1 pneumatic cylinder Rolling function – Non-motorised stainless steel roller, Ø140 x 350 mm – Gap adjustment: manual – Adjustable anti-clogging scraper Power supply: Three-phase 400V – 50 Hz Danfoss VLT frequency converters Operator display (HMI) Full machine control Buzzer + power-on indicator light Emergency stop buttons (including 1 on the cutting unit side) Dcsdpfx Aey Hdqasnfjg Electrical documentation available