Used Sleeve for sale (853)

Condition: new, Year of construction: 2025, 1A Gmatick Storage Paternoster (roll rack) The foil storage Paternoster foils is suitable to use for the storage of all 3D-films, it is used as a high storage at the membrane press or as a space-saving storage solution for the 3D foils. With our Paternoster you can storage on very small area approximately 2, 4m x 1, 2m a lot of film rolls (up to 32 rolls of a Ø 300 mm). The required film is thus immediately available at the push of button. Our Paternoster are available from 2.8 m up to 6, 0 m as standard Paternoster. Also special solutions are offered by us, please contact us, we will then find the right solution for your storage. As additional equipment we offer center sleeves, a manual cutting station or the full automatic cutting device and we have also ionization solutions available at Gmatick. • Storage rods ø 42.4 mm • Sleeves inside Ø max. 82 mm,. • Load chain as a hollow pin chain with a breaking load of 100 kN, • Chain pitch is 50 mm hole to hole and this is the raster for the positioning of the mounting foil bars. • Control with a key switch (dead man) for on / off • Rotational speed of the chain is approx. 5.5 m / min • Voltage 400 V, 3N; 50/60 Hz or as USA Version 480V 60Hz • Mains cable with CEKON plug 16A fuse protection (by the customer) 10A slow blow • ground load data at least 2, 2 kg / cm² • Side covering over the entire height of the Paternoster, guards from 2, 2 m above floor to top edge of the Paternoster. Iedoff Huwspfx Adiea • Requirement for the installation of the Paternoster is a viable, flat and solid floor, • Floating floors you can’t install a Paternoster. It is forbidden

Condition: used, Year of construction: 2017, functionality: fully functional, turning length: 3,000 mm, turning diameter: 805 mm, Used CNC cycle lathe with C-axis, featuring the following specifications: Ijdpfoxr U H Hjx Adioa Distance between centers: 3,000 mm Center height: 400 mm Swing diameter over bed: 805 mm Swing diameter over carriage: 720 mm Swing diameter over cross slide: 515 mm Cross travel: 400 mm Carriage length: 900 mm Cross slide length: 750 mm Bed width: 425 mm Spindle bore: 105 mm Spindle nose: A2-8/8 Spindle taper: MT 5 Speed range: 1st range: 0 – 425 rpm 2nd range: 425 – 1,700 rpm Feed rate: 0 – 7,000 mm/min Rapid traverse Z-axis: 10,000 mm/min Rapid traverse X-axis: 10,000 mm/min Ball screw Ø Z-axis: 50/10 mm Ball screw Ø X-axis: 32/5 mm Tailstock quill Ø: 106 mm Tailstock quill stroke: 215 mm Tailstock taper: MT 6 Number of tool stations: 12 Tool shank: 32 mm Boring bar: 50 mm Positioning accuracy: 0.01 mm Repeatability: 0.01 mm Motor power: 17 kW Pump motor: 0.57 kW Flow rate: 50 l/min Coolant tank capacity: 225 l Machine dimensions (LxWxH): 5557 x 2077 x 2227 mm Machine weight approx.: 6,460 kg Standard equipment: • CNC control, Fagor brand, model 8055 • Z/X-axis servomotors • Electronic handwheel for X and Z-axis • Servo spindle motor • Coolant system • Spindle sleeve and fixed centre MT 6 • Partial enclosure • Automatic shifting gearbox by Baruffaldi • Automatic lubrication system • Manual tailstock • Work light • Leveling bolts and nuts • Operating and programming manuals in German • CE version including CE Declaration of Conformity • For connection 400V, 50Hz, 3-phase Special equipment: • “C-axis”, continuous positioning • 1 piece 12-station disc turret, Baruffaldi brand, model TBHMA200-12, for live tools with VDI 40 mount • 2 pcs radial tool holders for live tools, VDI 40, type PRR-S-40-ER32/50-T • 1 pc axial tool holder for live tools, BMT65-A-ER32/50-T • 1 pc hydraulic chuck, Ø 400 mm, hydraulic cylinder Ø 92 mm, and hydraulic tailstock quill • Renishaw tool measurement system on the machine • 1 pc chip conveyor • 1 pc fixed steady rest for Ø 10–300 mm • 1 pc fixed steady rest for Ø 300–530 mm • 1 set soft jaws for Ø 400 mm chuck • 1 set hard jaws for Ø 400 mm chuck By the way, besides competitively priced new machines and inspected used machines, you can also expect more from us: • On-site consultation and solution finding • Organization of transport to your facility • Installation, commissioning, and handing over ready for operation • Spare parts supply • Control training for Siemens, Heidenhain, and Fanuc • Trained service personnel also in your area, etc. • 24/7 telephone availability • Tax-optimized trade-in of your old machine • Favorable financing, even without down payment Enquire now! Image shows machine as a new version with 2000 mm center distance.

Condition: good (used), Year of construction: 2003, Ref. -No.: 10603 Manufacturer: TOS Type: WRD 1500 Year of construction: 2003 Type of control: CNC Control: Heidenhain TNC 430 Storage location: Halberstadt Country of origin: Tschechien X-Travel: 10000 mm Y-Travel: 4000 mm Z-Travel: 1000 mm W-Axis: 800 mm V-axis travel: 2000 mm Spindle Diameter: 150 mm Max. Workpiece Weight: 25000 kg Tool Taper: ISO 50 DIN 68971 Tool Piece Magazine With: 60 Pcs./pcs. Spindle Turning Speed - Stepless: 10 - 2500 RPM Feed Speeds X/Y/Z Axis: 1 - 8000 mm / min Drive Capacity - Spindle Motor: 60 kW Total Power Requirement: ca. 80 kW Internal cooling: 20 bar Rotary table diameter: 2500 x 3000 mm Isdoxhbt Sopfx Adioa Support sleeve dimensions: 450 x 450 mm Rapid traverses Z + W: 12000 mm / min

Condition: used, Year of construction: 2003, functionality: fully functional, GILDEMEISTER - CTX 310 V3 Offer Details Stock number: 1039-9126 Machine type: CNC turning and milling center Manufacturer: GILDEMEISTER Model: CTX 310 V3 Year of manufacture: 2003 Control system: 840 D Siemens Storage location: D-59302 Oelde Country of origin: Italy Delivery time: by arrangement Basis of delivery: ex location Additional information: CNC Turning and Milling Center GILDEMEISTER - CTX 310 V3 - incl. bar loader IRCO Breuning - incl. 2x collet chucks - incl. 2x three-jaw chucks incl. various jaw sets - various VDI30 turning tool holders - various FZ tubes - approx. 20x 173E collets - collet sleeve for 185E collets (for bars up to Ø50) - 11x 185E collets WE OFFER YOU: - workshop-tested machines - free loading onto truck - NO auction fee - possible delivery (at extra charge) - unloading and commissioning (at extra charge) Technical Details Turning diameter: 210 mm Turning length: 580 mm Control: 840 D Siemens Centre height: 190 mm Swing diameter over bed: 330 mm Swing diameter over cross slide: 260 mm Main spindle: Speed range - main spindle: max. 4,000 rpm Drive power - main spindle: 10 / 7.5 kW Max. torque: 115 / 86 Nm Spindle bore: 68.5 mm Usable bar diameter: 51 mm C-axis: 0.001° Travels: Travel - X: 185 mm Travel - Z: 455 mm Turret: Number of tool positions: 12 stations Tool mounting: VDI 30 Driven tool stations: 6 stations Tailstock: Tailstock travel: 400 mm Max. thrust: 4,000 N Feeds: Rapid traverse: X: 20 / Z: 30 m/min Isdpfx Adsxtpfgoioa Feed force: 4.5 kN Total power requirement: 21 kW Machine weight approx.: 3.2 t Space required approx.: 8.0 x 2.2 x 2.0 m Accessories Documentation Chip conveyor Tailstock Coolant system Parts catcher C-axis Signal lamp Driven tool stations Bar loader: IRCO Breuning Turning tool holders: various Collet chucks: 2x Three-jaw chuck: ROTA NCW 185-46 Driven tools: 4x X / 2x Z

Year of construction: 2019, condition: excellent (used), Machine capacity CAPACITIES · Height of centre points Max. diameter for cylindrical grinding Distance between centres Max. length for cylindrical grinding Max. workpiece weight without steadies | Metric | |---|---| Iedpfx Adexr I Aneisa | 335 mm | | 450 mm | | 2150 mm | | 2100 mm | | 260 kg | TECHNICAL DATA Metric GRINDING SPINDLE UNIT Cylindrical grinding spindle 1: Electric spindle Max. grinding wheel dimensions: 610 × 50 × 203.5 mm Peripheral speed of grinding wheel: 30 - 125 m/sec Max. grinding spindle speed: 4420 min⁻¹ Cylindrical grinding spindle 2: Electric spindle Max. grinding wheel dimensions: 350 × 20 × 127 mm Peripheral speed of grinding wheel: 70 - 110 m/sec Max. grinding spindle speed: 6000 min⁻¹ X & Z AXES X & Z axes movement: ball screw X-axis traverse path: 460 mm X-axis speed range: 0-5000 mm/min X-axis resolution: 0.0001 mm Z-axis traverse path: 2590 mm Z-axis speed range: 0-5000 mm/min Z-axis resolution: 0.0001 mm B AXIS Swivel angle: 0 - 180° Type: automatic via torque motor C AXIS Workpiece speed range: 0-750 min⁻¹ Coupling type: headstock and tailstock TM 5 Tailstock sleeve diameter: 80 mm Tailstock sleeve stroke: 80 mm Tailstock adjustment accuracy: +/- 200 μm EQUIPMENT DETAILS GRINDING WHEEL DRESSING DEVICE Type: dressing station with fixed points for cylindrical grinding + electric spindle for diamond dressing roll COOLANT SYSTEM Type: magnetic separator and filter paper Flow rate / output: 50-200 l/min Tank capacity: 2000 litres Pump pressure: 5-20 bar OIL MIST EXTRACTION UNIT Volume flow / exhaust quantity: 2000 m³/h Max. power: 2.3 kW CNC CONTROL Brand: Siemens Model: Sinumerik 840 SL Unit system: metric MEASURING SYSTEMS FOR X & Z AXES Type: linear encoder

Condition: new, functionality: fully functional, color: white, overall weight: 515 kg, Year of construction: 2025, machine/vehicle number: IC8-12V, Infracube IC8-12V Diesel Container IBC - Dimensions LxWxH (mm): 1485 x 1150 x 1295 - Capacity: 800 litres - Weight: 515 kg Iodsxt Izyopfx Adisa - 12 volt pump with digital flow meter - 4 metres of hose and automatic nozzle - Fork sleeves on all four sides and lifting points UN, TÜV, ADR

Condition: ready for operation (used), functionality: fully functional, Buffer storage tank / stratified storage tank made of steel, insulated, standing on feet. Technical data / dimensions Available quantity: 1 Volume: approx. 60,000 liters Tank type: Pressure tank Condition: used Suitable for food: no Design: upright Diameter inside: approx. 2,800 mm External diameter: approx. 3,000 mm Cylindrical height: approx. 8,880 mm Total height: approx. 10,380 mm Specific weight of the medium: 1.0 to/m³ Operating pressure: Overpressure Operating pressure: 6 bar Test pressure: 7.8 bar Wall thickness underfloor: approx. 12 mm Wall thickness top: approx. 11 mm Wall thickness jacket / cylinder: approx. 8 mm Ground clearance: approx. 300 mm Operating temperature: 60 degrees Celsius Ijdpfjtwfxlex Adiea Material / composition Material inner casing: steel Feet material: Steel Insulation Insulation available Insulation thickness: approx. 100 mm Insulation material: Mineral wool Insulating jacket material: Galvanized steel Insulating jacket: screwed/riveted Notes: The insulation and the associated insulation cladding are damaged and may need to be be renewed/replaced. If you are interested, we will be happy to offer for the renewal of the insulation. The underside of the tank is not insulated. Equipment Stand form: Feet Number: 4 Width: approx. 400 mm Length: approx. 400 mm Top shelf type: Dished base Bottom shelf type: dished floor Top shelf: 2 x crane eyes 1 x flange socket DN 25 Jacket: 1 x steel pipe (26.9 x 2.6 mm), pulled down from the top floor 2 x flange DN 125 with internal distributor pipe 6 x immersion sleeves with temperature sensor incl. cable protection tube 2 x crane eyes Underfloor: 1 x outlet flange NW 50, pulled to the front 1 x oval manhole (320 x 420 mm) with insulating cover Documentation: Drawing

Condition: new, Bernardo Universal Lathe Titan 660 x 3000 Technical Specifications Distance between centers: 3000 mm Center height: 330 mm Swing over bed: 660 mm Swing over gap: 900 mm Swing over cross slide: 460 mm Bed width: 400 mm Spindle bore: 105 mm Spindle mount: DIN 55029, D1-8 Speed range: (16) 25 - 1600 rpm Longitudinal feed range: (25) 0.044 - 1.48 mm/rev Cross feed range: (25) 0.022 - 0.740 mm/rev Metric threads: (54) 0.45 - 120 mm Inch threads: (54) 7/16 - 80 TPI Tailstock quill diameter: 90 mm Tailstock quill travel: 235 mm Tailstock taper: MK 5 Motor power: 7.5 kW (10.0 HP) Machine dimensions (W x D x H): 4630 x 1200 x 1520 mm Approx. weight: 3300 kg Features • Versatile use in general mechanical engineering, production, single-part manufacturing, etc. • Central, user-friendly control for feeds and threading with leadscrew and feed shaft • Prism bed made of cast iron, inductively hardened and precision ground • Modern main spindle bearings with precision angular contact roller bearings • Hardened and ground gears and shafts, also in the feed gearbox • Rapid traverse longitudinal and cross as standard to reduce non-productive times • Large spindle bore (105 mm) for machining workpieces with large diameter • Smooth start-up via mechanical multi-plate clutch • Electromechanical foot brake to reduce non-productive times • Optimal cutting performance even during facing operations • Bed reinforced with robust ribs to stiffen the guideway and minimize vibration influences Scope of Delivery • 3-axis digital readout ES-12 V with LCD display • Slip clutch • Rapid traverse longitudinal and cross • LED machine light Iodjxxayfjpfx Adiea • 3-jaw steel chuck PO3-315 mm / D8 • Face plate 450 mm • Fixed steady rest – through hole diameter max. 180 mm • Travelling steady rest – through hole diameter max. 120 mm • 2 live centers • Motor with magnetic brake to CE standard • Foot pedal with brake function to CE standard • Initial filling with Shell Tellus 46 • Coolant system • Quick-change tool post with 4 holders • Safety device for quick-change tool post • Change gears • Reducing sleeve • Chip guard rear panel • Cable management via energy chain • Operating tools

Condition: used, Year of construction: 1995, Colors: 8 Gearless: No Fast Sleeve Change: No 4 motor CNC per printing deck: Yes Computer Supervision: Yes Web Width: 1320 mm Print Width: 1300 mm Min. Print Repeat: 380 mm Max. Print Repeat: 1100 mm Mechanical Speed: 350 m/min Iedpfxjxzrx Eo Adisa Working Speed: Up to 300 m/min Unwinding & Winding: Turret, FLYING SPLICE, Max. Reel Diameter 1000 mm Drying: 2 Zones, 4 Fans, 2 Gas Burners Video Camera: Yes Corona Treatment: No Web Guides: FIFE Viscosity Control: Yes Wash System: Yes, F&K Ceramic Anilox Rollers + Closed Chamber Doctor Blade 1x 80 L/cm, 2x 200 L/cm, 2x 120 L/cm, 4x 200 L/cm, 2x 320 L/cm, 3x 400 L/cm 200 sleeves, repeat between 390 mm and 1090 mm (8 for each repeat: 390, 400, 410, 420, 430, 450, 480, 510, 530, 540, 550, 630, 660, 670, 740, 780, 800, 850, 880, 930, 990, 1030, 1050, 1090 mm + 8 twinlock 740 mm + 8 twinlock 1030 mm) Mandrels for sleeves: 6x360 mm, 6x400 mm, 6x420 mm, 8x460 mm, 8x530 mm, 6x560 mm, 12x620 mm, 8x780 mm, 8x850 mm, 15x990 mm Printing cylinders: 8x380 mm, 8x390 mm, 12x400 mm, 8x410 mm, 8x450 mm, 6x460 mm, 7x470 mm, 4x490 mm, 12x500 mm, 8x510 mm, 12x530 mm, 8x540 twinlock, 6x560 mm, 8x570 mm, 8x580 mm, 8x590 mm, 12x620 mm, 9x640 mm, 12x660 mm, 6x670 mm, 6x730 mm Overall Dimensions: Length = 17 m, Width = 5 m, Height = 6 m Central Drum Diameter: 2280 mm

Condition: like new (used), Year of construction: 2022, operating hours: 105 h, functionality: fully functional, Haas ST50 Horizontal Turning Machine Slant Bed Lathe. Bought new directly from Haas and installed in Early 2023. As a "last of line" model from Haas (which they've yet to make this size since), this machine is fully loaded and as you can see from the build list below it is very well spec'd. It also only has 105 hours use. Viewing advised and welcome at our workshop in Canterbury, Kent. Videos can be sent and or uploaded to Youtube also. This machine and others we are selling are also listed else where. Isdpfexrf Stjx Adisa Please get in touch with us at Showan Hydraulics, Barham, Kent if you require any further details. £325,000 + VAT PRODUCT OVERVIEW • Maximum Capacity: 25.5" x 80" (648 x 2032 mm) • Spindle Bore: 8.5" (216 mm) • Swing Over Bed: 34.5" (876 mm) • Main Drive: 55 hp (41 kW) vector drive • Spindle Speed: 1200 rpm, 2-speed gearbox • Spindle Nose: Front and rear A2-15 • Chucks: 25" (635 mm) Manual 3-Jaw and 4-Jaw Chucks • Turret: 12-station bolt-on turret • Tailstock: Programmable servo with MT6 quill • Control System: 15" touchscreen interface with USB port, memory lock keyswitch, and colour remote jog handle • Additional Features: Rigid tapping and variable flow coolant pump _____ STANDARD FEATURES • Bolt-On Toolholder Kit: Comprehensive set of toolholders, sleeves, coolant block, and turning stick clamps for flexible setup. • 1200-RPM Spindle: Powerful 55 hp (41 kW) A2-15 spindle with 2-speed gearbox for optimal torque and speed. • Program Memory: 1 GB onboard memory for program storage and backup. • Coolant System: 95-gallon (360 L) tank with 3/4 hp (0.6 kW) pump del

Condition: used, Line boring machine WEBO with 4 stations type B 20 Iodpfx Aoihmwtsdija make no. 376/13; 376/14; 376/27; 376/36 year of construction approx. 1970 drilling capacity 20 mm spindle adaptor MK 2 - long spindle sleeve drilling head distance 335 mm throat 260 mm pinol stroke 190 mm table size 350 x 1500 mm distance drilling spindle/table min.30 mm / max. 700 mm Spindle speed drill head 376/13 355, 500, 710, 1000, 1400, 2000, 2800, 4000 rpm. Spindle speed drill head 376/14 355, 500, 710, 1000, 1400, 2000, 2800, 4000 rpm. Spindle speed drill head 376/27 250, 355, 500, 710, 1000, 1400, 2000, 2800 rpm. Spindle speed drill head 376/36 180, 250, 355, 500, 710, 1000, 1400, 2000 rpm. Motor power 1,1 / 1,3 kW Mains connection 380 Volt, 50 Hz - Spindle speed via 2 motor speeds and 4 V-belt steps - drill head height adjustment via toothed rack and hand crank approx. 300 mm - height adjustable drilling table approx. 350 mm space requirement L x W x H 1750 x 1100 x 1900 mm weight 1900 kg good condition

Condition: new, The VHF 1.1 is a compact and versatile Conventional Vertical Milling Machine in the Universal Milling Machines category, designed by KNUTH. This universal milling machine boasts a robust frame made of vibration-dampening cast iron, ensuring stability during operations. Equipped with a horizontal spindle and a swiveling vertical milling head, the VHF 1.1 allows for infinitely variable spindle speed and feed on the X-axis, making it ideal for diverse applications in training departments, repair shops, and model-making workshops. Its 1.000 x 240 mm setup area and 535 mm travel on the X-axis facilitate various machining tasks, while the included coolant system and chip tray enhance functionality and cleanliness. Users benefit from the extensive standard equipment, which includes a 3-axis position indicator, drill chuck, reducing sleeves, and more. With its precise and powerful performance, the VHF 1.1 is an outstanding choice for anyone in need of a reliable milling machine. Don’t hesitate to request a quote and elevate your milling capabilities today! Iodpfxsuyh Egs Adiea

Condition: used, mileage: 5,874 km, Year of construction: 2021, Serial number: YV2RT60FXKA84xxxx Please contact ATS Norway for more information Please provide reference number upon request: 20511 Specifications: - 2021 model - 5874 km (will increase slightly) - Eu-approved until: 21.02.26 - Euro 6 engine - 8x2 - 551 Hp - Suspension on 1st and 2nd axle: Steel - Suspension on 3rd and 4th axle: air - 2 x 110 liter variable pumps - 2 x manual extensions for main boom and 2 x for jib Iodpfx Adowphixeiea - Scanreco optical remote control (Top model) - Weight cell main boom - Extra function for main boom and jib - Auto leveling (The car puts itself in a level position ready for lifting.) - Virtual room (Possibility to limit all axes with a few keystrokes, no need to go to a workshop for this. Brilliant when working under high voltage etc.) - SKF central lubrication of the crown and up to the first joint - Extra function fully extended on jib - Single winch hook (Jib / main boom) - 2-part winch hook (Jib / main boom) - 4-part winch hook (Main boom) - Hook for jib - Hook for main boom (Large hook) - Emergency lowering unit (24 volts) - Wire stop sensor and sleeve - 4 ton winch - Diagnostic cable for online help (Remote help) - Danfoss valve center - 2 x 2 ton counterweight (Must only be used for cranes above the cabin otherwise the counterweights are not needed, and these can be removed as needed) - Front support leg Construction: - 4 x work lights strategically placed inside each support leg cabinet. - 50" LED bar work light rearward on the cabin - Powerful LED lamps in the crane. - VBG mount, with air servo control unit mounted in the rear cabinet left side. - Bracket on the roof - 2 pcs high beam LED bar on the roof forward (daylight!!). - Orange work warning LED beam on the roof. - EasyUp foldable ladder in the side with railing. - Boxes for chain, chainsaw etc. Mounted on the rear support leg so that these are driven out together with the support leg and are at the same time packed away while driving. - Charger for control in the cabin - Plastic internal screens axle 3 and 4. - 3 edge pull-out cabinet between axle 3 and 4 - On the left side between axle 2 and 3 there is a large cabinet with 500 W fan heater installed to hang clothes to dry etc. - Plane / bottom at the rear closed with alloxed aluminum floor plates that are cut to fit the car perfectly, with rounded edges for a very professional send. - CNC manufactured plates up the rear edge of the cabin. - Fully painted sides, cabin and stern. - Resting cradle for crane for driving without jib. - 5 support leg plates. 4 pcs 80x80x6 cm. placed in dedicated cradles at the rear on the "level" - Right side large cabinet 1.2 x 1 meter - Powerful LED back / work lights at the rear. - Rear part of the car rebuilt with CNC manufactured plates, and beautiful LED taillights have been installed in several stages. - Hatches strategically placed for access to relevant devices under the bodywork. - Precisely cut out fields in the side coverage for access to the screen, manual controls, emergency lowering functions etc. - Marker lights along the side mounted so that they flash together with the turn signals / direction indicators - Cradle to hold the jib when not in use. - Hydraulic extra function dismantled main boom and jib,...

Condition: new, Bernardo Production Lathe Goliath 660 x 3000 incl. 3-Axis Digital Readout Technical Specifications Centre distance: 3000 mm Centre height: 330 mm Swing over bed: 660 mm Swing over gap*: 870 mm Swing over cross slide: 420 mm Bed width: 400 mm Spindle bore: 105 mm Spindle mounting: DIN 55029, D1-8 Speed range (16 steps): 36 – 1600 rpm Longitudinal feed range (65 steps): 0.063 – 2.52 mm/rev Cross feed range (65 steps): 0.027 – 1.07 mm/rev Metric threads (22): 1 – 14 mm Inch threads (26): 2 – 28 TPI (G/1") Quill diameter: 75 mm Quill travel: 150 mm Quill taper: MT 5 Motor power: 9.0 kW (12.0 HP) Machine dimensions (W x D x H): 4500 x 1280 x 1650 mm Approx. weight: 3990 kg * Removable bed gap: 240 mm Features • Versatile applications in general engineering, production, single-part manufacturing, etc. • The one-piece cast machine bed offers extremely high rigidity and low vibration, fulfilling a key requirement for precision turning • Modern headstock bearing with precision angular contact ball bearings • Central, user-friendly control for feeds and threading, with lead and feed screws • Rapid traverse (longitudinal and cross) as standard to minimize non-productive times • Large-dimensioned, hardened, and precision-ground gears • Removable gap bridge enables machining of large-diameter workpieces • Adjustable tailstock for taper turning, handwheel with adjustable fine scale (0.02 mm) • Electromechanical foot brake to reduce non-productive times • Excellent machining performance even during facing operations Iodpfxjxxaxno Adija Scope of delivery • Slip clutch • Rapid traverse (longitudinal and cross) • LED machine lamp • 3-axis digital readout ES-12 V with LCD display • 3-jaw chuck PS3-315 mm / D8 • Face plate 630 mm • Fixed steady rest – max. bore diameter 250 mm • Travelling steady rest – max. bore diameter 110 mm • 1 live centre / 1 revolving centre • Motor with magnetic brake according to CE standard • Foot pedal with brake function to CE standard • Factory fill with Shell Tellus 46 • Coolant device • Quick-change toolpost with 4 holders • Safety guard for quick-change toolpost • Reducing sleeve • Chip guard (swarf back panel) • Operating tools

Condition: excellent (used), Year of construction: 2007, • Maximum possible drilling depth: 1200 mm • Maximum hole diameter: 32 mm • Minimum drilling diameter: 6 mm • Longitudinal travel (X-axis) table: 1800 mm • Cross travel (Z-axis) column: 1700 mm • Cross travel (W-axis) drilling head: 1150 mm Isdpfx Adexyf E Neija • Vertical travel (Y-axis) drilling head: 1200 mm • Clamping surface NC table: 1500 x 1000 mm • Maximum table load: 10 t • Rotary axis (B-axis) rotary table: 360° • Rotary axis (A-axis) drilling head: -25°/+15° • Feed rate: 1-15 m/min (Y-axis: 1-10 m/min) • Rapid traverse speed in all axes: 15 m/min (Y-axis: 10 m/min) • Maximum spindle speed: 6000 rpm • Minimum spindle speed: 60 rpm • Tool holder: SK 40 • Tool clamping: OTT • Rated power main drive (100% ED, S1/40% ED, S6): 9/13 kW • Coolant tank capacity: 1000 l • Maximum coolant pressure: 100 bar • Low-pressure external and high-pressure internal coolant supply • Power supply: 3x 400 V; 50 Hz • Required installation space (L x W x H): 6550 x 5350 x 4130 mm • Machine weight: 12,000 kg Deep Hole Drilling Machine Equipment • CNC control: HEIDENHAIN iTNC 530 • Interpolated rotary table with minimal backlash, dimensions 1500 x 1000 mm • Swiveling drilling head +15°/-25° • Shank drilling head • Handwheel HR520 • Fixed supports (2 units) • Tool magazine: ELB tools: 12 pcs (max. diameter: 32 mm / max. length: 1550 mm) Standard tools: 12 pcs (max. diameter: 140 mm / max. length: 400 mm) • Direct measurement and positioning system in X, Y, and Z axes • Collision monitoring system for supports and drill sleeves • Oil cooler • Coolant flow control system • Adjustable coolant nozzles • Cooling unit for electrical cabinet • Enclosed upper cover (roof) • Drip tray for machine and tank facility (tray height 30 mm) • Extraction system • Infrared touch probe • Drilling depth extension 1200 mm (retrofit) • Chip conveyor

Year of construction: 1970, condition: ready for operation (used), A horizontal boring and milling machine Scharmann is available. Spindle sleeve diameter: 120mm, travel X/Y/W: 1600mm/1600mm/600mm, speed: 1000rpm, table dimensions X/Y/Z: approx. 1200mm/1400mm, max. table load: 6000kg, column diameter: 220mm, table rotation: 360°, rapid traverse: 380mm/min, feed: 2400mm/min. Machine dimensions X/Y/Z: approx. 4500mm/2600mm/3000mm, weight: approx. 17000kg. Dokumentation vorhanden. An on-site inspection is possible. Iedpoxyk Tlefx Adija

Condition: used, Centrifugal fan NICOTRA - Gebhard Type P2M-M3M4J-RRB-ATEX RD/0 Fabric No. 318844/626052/1 Year of construction 2008 Volume flow 10000 m³/h = 166 m³/min. Pressure p 1.2 kg/m³ Air inlet Ø 500 mm Air outlet 450 x 450 mm Motor speed 1435 rpm Motor power 4 kW Mains connection 400 Volt 50 Hz - Fan wheel with 8 fan blades - Directly flanged drive motor - Mounted adapter ring with flexible sleeve Ø 500 mm Ijdjpp D I Sepfx Adiea - Adapter flange for air outlet from rectangular flange 450 x 450 x to Ø 500 mm - Galvanized sheet metal housing Overall height without adapter ring 1100 mm Space requirement L x W x H 1100 x 1000 x 1630 mm Space requirement with pallet L x W x H 1400 x 1070 x 1800 mm Weight of centrifugal fan 200 kg Weight with pallet 230 kg Very good condition

Condition: new, -Dimensions (LxWxH): 500x840x540 mm -Dough capacity: 50/280 kg -Dough portions: from 30 to 300 g -Voltage: 400 V -Power: 0.93 kW -Weight: 74 kg -Compact design, easy to use and clean. -Machine complies with CE standards. Isdpfx Adsxvxhioioa -Portioning of dough from 30 to 300 grams. -Portioning error: +/- 5 g from desired weight. -Operates by dough extrusion using a spiral tool. -Equipped with two adjustment systems: sensor and cone. -Entire machine built from stainless steel and aluminum for robustness and easy cleaning. -All parts in contact with the product are removable via handy handwheels and are easily washable without requiring maintenance. -The outfeed hopper is easily removable for replacement of reduction sleeves. -All components are compliant with hygiene and safety standards. -Regular cleaning requires no special maintenance.

Condition: good (used), Year of construction: 1991, functionality: fully functional, product width (max.): 2,500 mm, working width: 2,500 mm, roll diameter: 1,500 mm, year of last overhaul: 2024, We have available for sale a Cobden Chadwick pre-print press line- 2500mm wide- see photographs. This is a fantastic opportunity and is the best conditioned pre-print press we have ever offered for sale/relocation. The machine controls were upgraded by Pre-Print Technology Ltd in 2017 – new servo control deck positioning + downstream register system. Please kindly let us know as soon as possible if you would like to visit the site to inspect the press line. Cobden Chadwick Linerflex press - manufactured 1991 Machine location: United Kingdom Cobden Chadwick Linerflex press consisting of the following 6 colour C.I 1 colour pre-tint unit with cantilever 1 colour downstream unit with cantilever Twin Wood & Stirling unwind Marquip splicer Warburton rewind Drive system for pre-tint, chill rollers, varnish unit and rewind Drying: IR cassettes by Waverley Fife web guiders Sero motors for print deck positioning Original press performance parameters; Maximum speed: 300 metres per minute Repeat range: 700mm to 2000mm all units Gear pith: 10mm Maximum print width: 98” PLC: Mitsubishi Main press frames: Light blue azure Ancillary equipment Heaford Cobra mounter proofer AV Flexologic Mounter proofer Print roll stock (120 off) including print gear and sleeve attachments Anilox roller stock (17off) including anilox gear and clutch attachments. Cantilever print sleeves (12off) Print roller and anilox storage racking system with overhead hoist C.I temperature control unit Chiller unit for chill rolls Print unit doctor chambers with related inking system Ijdpfet Uc Iqox Adiea Mobile operator trolley for print deck access Mobile Print roller and anilox roller trolleys C.I hoist lifting attachment bar Machine voltage: 415V, 50hz

Condition: good (used), ASSORTMENT / Soft - Hard Jaws for Three-Jaw Chuck / Base holder-tool holder / Sleeves / T-nuts -21x Set Soft Jaws (Special Jaws) Hard Jaws for Three-Jaw Chuck Iodpewtbqdofx Adioa -Jaw dimensions LxW 120x60mm 60 degree - pointed toothing - 3mm tip distance -4x Base holders (CNC lathe) for holding boring bars and internal turning tools -20x Reducing sleeves (various internal diameters) for internal turning tools -Various T-nuts and screws -Remainder see pictures Errors / input mistakes excepted

Condition: new, Year of construction: 2025, NEW Column Drill FLOTT SB 13 plus - Spindle: B 16 (MK II at extra cost €150 / Item no. 212504) - Tapping device - Control panel with OLED display - LED lighting - Rapidly adjustable and ergonomic drilling depth stop - Infinitely variable speed control via central rotary knob - Thermal overload protection - Spindle stop - Drill guard with electric safety interlock - Continuous/Standard drilling capacity (mm): 13/15 in E335/ST60 - Tapping capacity (depending on pitch): M10 - Drilling depth (mm): 60 - Throat (mm): 220 - Usable working area (W x L) (mm): 300 x 250 - Rack and pinion table height adjustment Iodpfx Adjxrdrxeiea - Spindle speed infinitely variable (rpm): 40 – 4000 - Dimensions (mm): 420 x 540 x 1780 For further TECHNICAL DATA please refer to the product sheet! OPTIONAL Drill Package 2 (296591) - €300.00 - [felix] 2.0 80 machine vice - Quick-action drill chuck B16 1-13 mm (accuracy 0.17 mm) - Taper shank B16/MK II - Reducing sleeve MK II/MK I 3-year warranty for single-shift operation NOT THE RIGHT MACHINE? WE ARE AN AUTHORIZED FLOTT DEALER AND CAN OFFER YOU ALL PRODUCTS FROM THE FLOTT RANGE! REQUEST A QUOTATION!

Condition: like new (used), Year of construction: 2024, Manufacturer: Optimum Year of manufacture: 2024 Condition: as new, workshop-tested Delivery time: immediately available Technical Specifications Centre height: 165 mm Centre distance: 830 mm Swing over bed: 330 mm Swing over cross slide: 208 mm Turning length in bed gap: 430 mm Ijdexykniopfx Adija Spindle speed range: 16 steps, 70–2000 rpm Drive motor: 1.5 kW, 400 V, 50 Hz Spindle mount: Camlock DIN ISO 702-2 No.4 Spindle bore: 38 mm Spindle taper: MK5 Tailstock taper: MK3, quill travel 110 mm Weight: approx. 512 kg Machine dimensions (L×W×H): 1685 × 745 × 1590 mm Feeds and Thread Cutting Metric: 0.4–7 mm/rev (26 pitches) Imperial: 56–4 TPI (34 pitches) Longitudinal feed: 0.052–1.392 mm/rev (32 feeds) Cross feed: 0.014–0.38 mm/rev (32 feeds) Accessories: Fixed steady rest (Ø 6–50 mm) Travelling steady rest (Ø 8–30 mm) LED machine lamp Reducing sleeve MK5/MK3 Two fixed centre points MK3 Four-way tool post 16 mm Change gear set Machine base Initial fill with quality oil Operating tools

Condition: new, neu ca. 4 Monate ab Auftragse Bulgarien 36070 € 688.94 € 400 mm Iedpfexzuu Ajx Adioa 1000 mm 200 mm 52 mm 235 mm 320 mm 6 6 M 12 50-2.240 1/min 80 0.015 - 0.6 mm/U 0.0075 - 0.3 mm/U 40 0.25 - 7.5 mm 120 - 4 Gänge/" 0.0625 - 1.875 480 - 16 235 mm 110 mm 50 mm 4 MK 100 mm 4 kW 2750 mm 1100 mm 1600 mm 1540 kg driven by manual transmission 3-axes digital readout Fagor 40i quick change toolpostMultisuissewith4 holders (3 square, 1 round) 3-jaw chuck Bison 3204/DIN6350, Ø 200 mm spindle noseNr. 6 DIN 55027 four way rapid traverse device spindle dead center coolant equipment 1 pce. flange plate for lathe chuckØ 200 mm 1 adapter sleeve full length rear splash guard leadscrew and shaft protection safety guard for the chuck toolholder guard levelling bolts and plates quick release tailstock low voltage machine lamp operating manual machine according to "CE" FURTHER TURNING LENGTHS: turning length 750 mm € 35 360,00

Condition: used, Year of construction: 2022, gebraucht 2022 1672 prompt, Zwischenverkauf v Bulgarien 27700 € 1 1 23600 € 400 mm 1000 mm 200 mm 52 mm 235 mm Iedpfx Aowirxdjdiea 320 mm 6 6 M 12 50-2.240 1/min 80 0.015 - 0.6 mm/U 0.0075 - 0.3 mm/U 40 0.25 - 7.5 mm 120 - 4 Gänge/" 0.0625 - 1.875 480 - 16 235 mm 110 mm 50 mm 4 MK 100 mm 4 kW 2750 mm 1100 mm 1600 mm 1540 kg Demo machine / mint condition (New price € 36,070.00) driven by manual transmission 3-axes digital readout Fagor 40i quick change toolpostMultisuissewith4 holders (3 square, 1 round) 3-jaw chuck Bison 3204/DIN6350, Ø 200 mm spindle noseNr. 6 DIN 55027 four way rapid traverse device spindle dead center coolant equipment 1 pce. flange plate for lathe chuckØ 200 mm 1 adapter sleeve full length rear splash guard leadscrew and shaft protection safety guard for the chuck toolholder guard levelling bolts and plates quick release tailstock low voltage machine lamp operating manual machine according to "CE" FURTHER TURNING LENGTHS: turning length 750 mm € 35 360,00

Condition: used, Year of construction: 2020, gebraucht 2020 1658 prompt, Zwischenverkauf v Bulgarien 26500 € 1 22600 € 400 mm 1000 mm 200 mm 52 mm 235 mm 320 mm 6 6 M 12 50-2.240 1/min 80 0.015 - 0.6 mm/U 0.0075 - 0.3 mm/U 40 0.25 - 7.5 mm 120 - 4 Gänge/" 0.0625 - 1.875 235 mm 110 mm 50 mm 4 MK 100 mm 4 kW 2750 mm 1100 mm 1600 mm 1540 kg This machine is used in our workshop for repair work, therefore it has only been used very little so far. (New price € 36,070.00) Iodpfx Adowirdtjisa driven by manual transmission 3-axes digital readout Fagor 40i quick change toolpostMultifix Type Bwith4 holders (3 square, 1 round) 3-jaw chuck Bison 3204/DIN6350, Ø 200 mm spindle noseNr. 6 DIN 55027 four way rapid traverse device spindle dead center coolant equipment 1 pce. flange plate for lathe chuckØ 200 mm 1 adapter sleeve full length rear splash guard leadscrew and shaft protection safety guard for the chuck toolholder guard levelling bolts and plates quick release tailstock low voltage machine lamp operating manual machine according to "CE"