Used Slots for sale (2,848)

Condition: ready for operation (used), functionality: fully functional, BEHR ST 150 / Vertical slotting machine with swiveling head - Stroke up to max. 175 mm - Head tilting in both directions, 5-8 degrees each - Table height / lower edge of ram guide: 260 mm - Rotary table diameter: 340 mm - Table longitudinal travel: 320 mm - 3 stroke speeds: 17-54-108 strokes per minute - Maximum slot width up to 26 mm - Feed in X/Y axes, speed adjustable - Rotary table adjustment manual - Three-jaw chuck Dimensions (LxWxH): 1.5x1.2x2 meters / Weight: 1600 kg Iodsy R S Rvjpfx An Notk Errors and omissions excepted.

Condition: ready for operation (used), Grooving machine / Vertical, Type VS 600 - Rotary table diameter 600 mm Iodpfsza Ulasx An Notk - Rotary table - Indexable - Stroke approx. 360 mm - Three-jaw chuck 325 mm - Cross table Dimensions: L x W x H 1.9 x 1.2 x 2.3 meters / Weight 1700 kg Errors and omissions excepted.

Condition: good (used), Slotted sieve basket, slotted sieve baskets, replacement basket, replacement baskets, separator basket, separator slotted sieve, separator filter grid, separator grid -Slotted screens for: screw separator -Gap dimensions: 1-2 mm -the item can be sold as a whole or individually -Price on request -various dimensions: -1x: 310/432 mm piece 40 EUR net -1x: 140/1000 mm piece 40 EUR net -1x: 150/1000 mm piece 40 EUR net Itodpjvpp D Eofx An Njk -1x 315/1000 mm piece 70 EUR net -Complete weight: 44 kg

Condition: excellent (used), Separator screen, slotted screen basket, slotted screen baskets, replacement basket, replacement baskets, separator basket, separator slotted screen, separator filter grid, separator grid, separator screen for slurry separator, round screen, slotted screen Ijdpfx Anjwx E Tao Njtk -Slotted screen: separator screen -Gap dimensions: mm -Inside: Ø 129 mm -Dimensions: Ø 136 x 800 mm -Weight: 3.8 kg

Condition: good (used), Year of construction: 1956, Slotting machine, slotting machine, high-speed planer, keyseating machine, keyway broaching machine, keyway broaching machine, keyway tool, broaching machine, slotting machine, horizontal slotting machine, planing machine, power high-speed planer -Manufacturer: Lange & Geilen, horizontal slotting machine Kraft-Schnellhobler -Stroke: 350mm -Stroke rate: 20 - 110 1/min -Clamping table: 380 x 280 mm -Travel: X 410 mm Z 320 mm -T-Slot: 14mm -Propulsion: AEG 3 kW -Dimensions: 1460/1170/H1350 mm -Weight: 1140 kg Iedjlzmxyspfx An Nstk

Condition: used, Year of construction: 2023, operating hours: 259 h, functionality: fully functional, machine/vehicle number: 1200002, travel distance X-axis: 1,270 mm, travel distance Y-axis: 508 mm, travel distance Z-axis: 635 mm, Like-new Haas VF-4-EU CNC vertical machining center with only 259 operating hours. The machine is in excellent optical and technical condition. The VF-4 is already fully prepared for 4-/5-axis operation from the factory – the extensive 5th-AXIS package is installed: - Axis cards for the 4th and 5th axes - Dynamic workpiece offset - Tool center point control - High-speed machining - Programmable coolant nozzle - Wireless Renishaw measuring probe and tool probe In addition, the machine is unusually well-equipped: - TSC – internal coolant supply with 21 bar - Spiral chip conveyor - Complete coolant maintenance package (automatic replenishment, oil separator, mist collector) - Fast 30+1 tool changer - Spindle with 10,000 rpm The control system is the current Haas Next Generation Control with touchscreen, WLAN, Ethernet, and HaasConnect remote monitoring. This makes the machine immediately ready for demanding machining tasks. The original transport securing devices are available. An original Haas tool cart for SK40 is also included. Inspection and demonstration under power are possible at any time by appointment. Loading and transport can be arranged. A suitable TRT-210 CNC rotary table is offered in a separate listing and can be included in the package if desired. The LANG base plates are not included in the scope of supply. Technical data: - Travel ranges X / Y / Z: 1,270 × 508 × 635 mm - Spindle nose to table: 107 – 742 mm - Table: 1,321 × 457 mm, 5 T-slots (16 mm), max. table load 1,588 kg - Spindle: 10,000 min⁻¹, BT/CT 40, inline direct drive, liquid-cooled - Drive power: 22.4 kW - Max. torque: 122 Nm at 2,000 min⁻¹ - Rapid traverse X / Y / Z: 25.4 m/min - Feed rate max.: 16.5 m/min - Tool changer: Side SMTC, 30+1 positions - Tool max. diameter / length / weight: 64 mm / 330 mm / 5.4 kg - Tool change time (chip-to-chip): approx. 3.6 s - Connection voltage: 400 V / 50 Hz, 3-phase (internal transformer installed) - Compressed air: approx. 113 l/min at 6.9 bar - Coolant tank: 208 l - Weight: approx. 6,260 kg (with conveyor) Itjdpfx Asy Tp E Asn Nek Control: - Haas Next Generation Control with touchscreen - 1 GB program memory, Ethernet + WLAN - HaasConnect (remote monitoring), HaasDrop (wireless file transfer) - M130 media display, safe run, synchronized thread drilling - Early detection module for power failure, overvoltage protection - Equipment / options (all installed from the factory) - 5-axis package VF-YT (4th + 5th axis drive-side prepared, DWO/TCPC, high-speed machining, programmable coolant nozzle) - Wireless Renishaw measuring probe system (intuitive) - TSC – internal coolant supply through the spindle, 21 bar - Spiral chip conveyor - Coolant maintenance package (automatic replenishment, oil separator, mist collector) - Additional coolant filter (bag filter 25 µm) - Filter set for chip sump (200 µ) - Variable coolant flow (M-code controlled) - Blowing of the inside of the machine door - Lifting eyes, touchscreen, door lock

Condition: used, Plate assembly, clamping plate with T-slots 8000 x 2100 mm, 2-piece Clamping surface: Length: 8000 x Width 2100 mm Isdpfx Anjzc Nt Dj Njtk Plate thickness: 360 mm - Consisting of 2 clamping plates with 7 T-slots each (Length 4000 x Width 2100 x Plate thickness 360 mm) Transport dimensions: 2 plates stacked on top of each other Plate assembly: Length 4000 mm x Width 2100 mm x Height approx. 900 mm Transport weight of plate assembly: approx. 14 tons Good condition

Condition: good (used), max. ram stroke 230 mm throat 230 mm table diameter 0 mm are offered : 2 pieces of shaping spindle for Lorenz gear shaping machines type LS 630 to LS 1250 1x overhauled new Ijdew Ny S Rjpfx An Notk 1x has to be overhauled. Year of manufacture: unknown

Condition: excellent (used), Vacuum slot channel / suction channel Manufacturer: Blaschke Length: 18 meters = 59 feet 0.661 inches, 3 x 6 meter aluminum profiles Cross-section: 180 x 180 mm Itjdpozf Aqmsfx An Nek Including 3 vacuum carriages and fan 3 kW 380 volts Various bends and pipe sections

Condition: used, Table unit from a DROOP & REIN portal milling machine Clamping plate with T-slots made of cast steel gray cast iron Table unit with clamping plate and very solid guideway Table clamping surface 5500 x 2000 mm Travel of the table clamping plate approx. 3100 mm Itedpfx Anethuzpo Nek Table height 1050 mm Table load: max. 20 tons Ball screw: Ø 100 mm Thread pitch: 20 mm (single-start) - Processing table guided very stably on the bed - Metal telescopic guideway cover - comes from a DROOP & REIN portal milling machine - Longitudinal table movement via ball screw and SIEMENS servo motor - Clamping surface with 11 T-slots 28 mm - Drive via SIEMENS 1FT6134-6AB71-1AG2 servo motor with IC200448S/R encoder (RN 000 B25) Total length 9500 mm Width 2000 mm Overall height 1050 mm dead weight 28 ton. good condition

Condition: ready for operation (used), Year of construction: 1998, operating hours: 68,000 h, functionality: fully functional, travel distance X-axis: 1,660 mm, travel distance Y-axis: 510 mm, travel distance Z-axis: 510 mm, rapid traverse X-axis: 20 m/min, rapid traverse Y-axis: 20 m/min, rapid traverse Z-axis: 20 m/min, feed rate X-axis: 5,000 m/min, feed rate Y-axis: 5,000 m/min, feed rate Z-axis: 5,000 m/min, controller manufacturer: Mazatrol M Plus, table width: 510 mm, table length: 2,000 mm, overall weight: 7,320 kg, spindle speed (max.): 10,000 rpm, operating hours of spindle: 36,000 h, number of spindles: 1, number of slots in tool magazine: 48, input voltage: 400 V, Equipment: chip conveyor, rotational speed infinitely variable, We are offering this used Mazak VTC-20C vertical machining center, manufactured in 1998. Manufacturer: Mazak Model: VTC-20C Year of manufacture: 1998 Condition: ready for use Category ID: 1452 Type ID: 4156 Machine type: vertical machining center Control: Mazatrol M Plus Operating hours: approx. 68,000 Spindle hours: approx. 36,000 Work table Table size: 2000 x 510 mm T-slots: 5 pieces Distance between T-slots: 100 mm Slot width: 18 mm Travel distances X-axis: 1660 mm (with partition 2 x 560) Y-axis: 510 mm Z-axis: 510 mm Rapid traverse rate Rapid traverse: X/Y/Z-axis: 20 m/min X/Y/Z-axis 1 - 5,000 mm/min Tool magazine Tool holder: SK 40 Itedpfozkkliex An Nek Tool positions: 2 x 24 Spindle speed: 10,000 rpm Accessories: Partition; Renishaw probe; chip conveyor !!! Optionally with 2 Röhm vices If you have any questions or need more information, please feel free to send us a message or call us.

Condition: used, Year of construction: 2018, operating hours: 6,442 h, Technical Data Working Area Axis Travel - X-axis: 4000 mm - Y-axis: 1970 mm - Z-axis: 455 mm Machining Area - X working area: 3000 mm - Y working area: 1550 mm Iodpfjzuw E Rox An Njtk - Z clearance: 250 mm Axis Systems - X-axis: Helical rack and pinion drive - Y-axis: Precision ball screw drive - Z-axis: Precision ball screw drive - Linear guides on all axes - Automatic central lubrication Main Spindle - 5-axis electro spindle - Type: 5-axis spindle with universal joint - Power: 12 kW (S6 operation) - Tool holder: HSK F63 - Maximum speed: 24,000 rpm - Ceramic bearings with air cooling - Full power available at approximately 12,000 rpm - Speed range: 1,000 - 24,000 rpm - Clockwise rotation - Integrated tool changer interface - Liquid-cooled spindle - Electrically controlled extraction hood - Maximum tool weight: 6 kg - Maximum saw blade diameter: 350 mm Tool Changer System 12-position linear tool magazine - Mounted on the left side of the machine frame - Separate station for tool changers - Maximum tool diameter: 250 mm - Maximum tool length: 240 mm 18-position disc tool magazine - Mounted on the gantry - Suitable for drilling tools and tool changers - Maximum tool diameter: 250 mm - Maximum tool length: 280 mm Drilling Aggregated Head DH18 6H 1S drilling head - 12 vertical spindles: 7 spindles in the X direction, 5 spindles in the Y direction - 4 horizontal spindles in the X direction - 2 horizontal spindles in the Y direction - Drilling stroke: 70 mm - Maximum drilling depth: 70 mm - Tool holder: 10 mm - Individual control of the spindles - Integrated slotting saw - Saw blade diameter: 120 mm - Maximum slotting saw blade thickness: 5 mm - Speed up to 7,500 rpm Vacuum and Clamping System Console Table - 6 consoles with front and rear stops - Wireless two-circuit vacuum system - Height of vacuum cups: 100 mm - Pneumatic console locking - Programmable pneumatic stops - 4 adjustable side stops - Reinforced support arms - Load-bearing capacity of the support arms: 40 kg each Vacuum Pump Capacity: - 90 m³/h at 50 Hz - 108 m³/h at 60 Hz - Additional vacuum connection for template machining - Controlled compressed air connections for frame clamps - Separate vacuum and compressed air switching for all consoles WoodFlash Software Package Control Panel - Complete machine operation via the CNC panel - Program creation and editing - Tool and workpiece management - Manual machine commands - Monitoring of vacuum, compressed air and safety systems Mobile Control Panel - 24" LED monitor - Keyboard and mouse - USB connection Operator Device for Feed Rate - Manual feed override potentiometer - Variable feed rate adjustment during machining Safety Devices - CE safety system - Safety mats instead of light curtains - Emergency stop system - Protective fence on the left side - Safety monitoring of the doors - Sensors to monitor vacuum and compressed air Optional Equipment - External release switch - Protected energy chain system - Additional locking for A and C axes - Saw blade changing station on the gantry - Operating hours: 6442 hrs.

Condition: ready for operation (used), Vertical thread-rolling machine HENNING 03E -Henning - Metzingen -Year of manufacture 1981 -Rolling length approx. 1100mm -Motor power 3KW -Coolant system Dimensions L x W x H 0.7 x 0.5 x 1.7 meters / Weight approx. 450 kg Itsdozkv Euepfx An Njk Subject to errors and omissions.

Condition: like new (used), functionality: fully functional, Year of construction: 2025, overall weight: 370 kg, power: 3.5 kW (4.76 HP), input voltage: 400 V, input frequency: 50 Hz, broaching length: 800 mm, broaching speed: 3 m/min, total length: 920 mm, total width: 800 mm, total height: 1,950 mm, Manufacturer: Rausch (Haan/ Rhld) Model: RS 3 G/800 Machine No.: 2968/424 Year of manufacture: 1970 Weight: 370kg Overhaul: 8/2025 by Wiemers AG Our Ref. / Machine No.: WAG 787 General / Technical Data: Unused, overhauled mechanical vertical broaching machine by Rausch Pulling force: 3,000kg (30kN) Broaching speeds: 3m/min and 6m/min Return speed: 3m/min Maximum stroke: 800mm Maximum tool length: 1,000mm Table size / working surface: 340mm x 220mm / 430mm x 310mm Table opening: Ø 90mm for standard broaching mandrels Workpiece diameter: unlimited (without spray guard cabin) Dimensions (h x w x d): 1,950mm x 820mm x 900mm (h = table height from floor without attachments) Motor: 3.5kW Power supply: 400 Volt / 50 Hz Accessories / Special Features: Isdpeytvyxjfx An Nstk - Modified drive system with geared motor and toothed belt drive - 2 broaching speeds: 3m/min & 6m/min - External stroke adjustment, cross-machine reproducible tool length adjustment system - Integrated coolant unit with check valve and drain cock, including selector switch for automatic operation (does not automatically switch in swivel mode) - Patented coolant/lubricant swivel system - Three-sided enclosed, front-open spray guard cabin (no external operator panel) - Machine enclosure below the safety door with chip guard and tool storage area - Electrical cabling within steel protective conduits - Electrical jaw monitoring (tool removal control to prevent unintended retraction of the pull bridge) - Safety door with integrated emergency stop function - Control panel made from stainless steel sheet with permanent marking - 4 central lubrication points for the trapezoidal spindle drive - Machine documentation Remarks: The machine is fully overhauled, with the frame completely refurbished. The following wear parts have been replaced: - New trapezoidal spindles and spindle nuts made from cast wear-resistant bronze - All bearings and seals replaced - Central drive shaft is new - Coolant system (pump, check valve and drain cock), including coolant/lubricant swivel system, is new - Jaws are new (pull bridge additionally reinforced) - A switchable jaw monitoring system has been installed (additional safety for operators and to prevent tool breakage) - A safety door with interlock has been installed instead of the rubber reach-in protection - Tool length adjustment system relocated outside the machine compartment - Additional limit switches installed - Complete electrical system (control cabinet) with Siemens components is new - Control panel made of stainless steel with durable labeling - New geared drive motor (SEW) with toothed belt drive - Machine has been repainted with 2-component structural paint The machine is stored at our warehouse and can be inspected under power.

Condition: used, Festo ZA 2T tenon cutter for the precise milling and sawing of tenon joints in solid timber, as well as for the manufacture of windows and doors. The machine enables perfectly fitting timber joints thanks to precise depth and length adjustment with high repeatability. Ideal for window and door construction as well as for traditional timber joints in furniture making, including a set of Gold IV68 milling tools. Isdpfezryqwex An Notk Technical data: - Cutter diameter: max. approx. 340 mm - Cutting height: approx. 80 mm - Travel distance: approx. 1,300 mm - Further technical data: On request

Condition: good (used), 2 used T-slot angle plates Height: 1500 mm Width: 1000 mm Iodpey Iakfsfx An Njtk Depth: 500 mm 10 transverse slots 3 longitudinal slots First-class surface finish

Condition: new, Year of construction: 2023, functionality: fully functional, QATM Qcut 500 A Precision Cut-Off Machine Manufacturer: QATM / ATM Qness GmbH Type: Qcut 500 A Year of Manufacture: 03/2023 Machine Type: Automatic Metallographic Cut-Off Machine Condition: New / unused Cutting Disc Diameter: up to 508 mm (20") Drive Power: 15 kW S1 For sale is a new and unused QATM Qcut 500 A precision cut-off machine, manufactured in 2023, with extensive equipment, a belt filter system, and an extraction system. The machine is particularly suitable for the precise cutting and sectioning of samples in metallography, material and component testing, quality assurance, research and development, as well as for industrial laboratory and testing applications. The machine is additionally equipped with the option "Laser alignment aid for easy positioning of the workpiece." Technical Data: Manufacturer: QATM / ATM Qness GmbH Type: Qcut 500 A Year of Manufacture: 03/2023 Itjdpfxjzt N Rve An Nok Country of Manufacture: Germany Power Supply: 400 V / 50 Hz Connected Load: 30.0 kVA Fuse Rating: 32 A Drive Power: 15 kW S1 Cutting Disc Diameter: up to 508 mm (20") Speed at Ø 508 mm: 1000 – 2400 rpm Cutting Disc Arbor: Ø 32 / 40 mm Max. Sample Size at Ø 508 mm: 190 mm Max. Sample Weight: approx. 400 kg incl. clamping device Travel X-axis: 420 mm Travel Y-axis: 280 mm Travel Z-axis: 200 mm Positioning Accuracy Z-axis: 0.1 mm Working Speed X-/Y-axis: 0.001 – 50 mm/s Rapid Traverse X-/Y-/Z-axis: 80.0 mm/s Compressed Air Connection: 6 bar (± 2 bar) Noise Emission: max. 62 dB(A) at idle Operating Hours according to Display: 5 h 47 min Software Version: V 4.30 Belt Filter System: Manufacturer: QATM / ATM Qness GmbH Type: Belt Filter Automatic 285 Year of Manufacture: 03/2023 Belt Filter Type: UR 1030 Belt Filter Year of Manufacture: 2022 Rated Voltage: 3 × 400 V / N / PE, 50 / 60 Hz Rated Current: 100 mA Rated Power: 83 VA Dimensions: Machine Dimensions: approx. 1300 × 1820 × 1250 mm (W × H × D) Table Size without Z-axis: 700 × 500 mm Table Size with Z-axis: 550 × 500 mm Table Plate: Stainless Steel T-Slot Width: 12 mm Machine Weight: approx. 1000 kg Equipment: Option: Laser alignment aid for easy positioning of the workpiece Touchscreen control panel X, Y, and Z-axis control Joystick operation Stainless steel work table with T-slots Enclosed work area with viewing window Coolant nozzles QATM Belt Filter Automatic 285 Belt Filter UR 1030 Filter mist extraction system Coolant / filter unit Tools and clamping accessories according to images Piping and connection accessories according to images Operating manuals and documentation according to images Further accessories according to images Transport Data: Machine Weight: approx. 1000 kg Shipping by freight forwarder possible. Condition: New / unused. Year of Manufacture 2023. The machine has not been used in production. Operating hours according to display: only 5 h 47 min. Very well-maintained optical condition according to images. Display and control are shown as functional. Nameplates are present. Scope of Delivery: 1 × QATM Qcut 500 A Cut-Off Machine 1 × QATM Belt Filter Automatic 285 / Belt Filter Unit Filter mist extraction system Laser alignment aid Tools and clamping accessories according to images Piping and connection accessories according to images Operating manuals and documentation according to images Further accessories according to images. Scope of delivery as shown or described. Subject to changes, errors and prior sale.

Condition: ready for operation (used), Year of construction: 2004, operating hours: 11,298 h, functionality: fully functional, machine/vehicle number: 665001, travel distance X-axis: 700 mm, travel distance Y-axis: 550 mm, travel distance Z-axis: 450 mm, workpiece weight (max.): 2,000 kg, spindle speed (max.): 42,000 rpm, number of slots in tool magazine: 40, No minimum price – guaranteed sale to the highest bidder! Submitting a bid obligates you to collect the item within the period of September 21st to October 1st! TECHNICAL DETAILS Travel in X-axis: 700 mm Travel in Y-axis: 550 mm Travel in Z-axis: 450 mm Feed Axes Max. travel speed X, Y, and Z axes: 30 m/min Max. acceleration X, Y, and Z axes: 15 m/s² Positional accuracy TP according to DIN ISO 230-2: 0.005 mm Repeatability: 0.002 mm Work Table Table length: 850 mm Table width: 700 mm Number of T-slots: 5 T-slot dimensions: 18 H12 Table load: 2,000 kg Max. workpiece weight: 2,000 kg Distance spindle center – table: 550 mm Spindle Spindle mount: HSK-E 40 Spindle speed: 3,000 - 42,000 rpm Spindle power: 17 kW Tool Changer Tool magazine positions: 40 MACHINE DETAILS Machine type: CNC HSC machining center CNC control: Andronic Electrical Connection Data Supply voltage: 400 V Supply frequency: 50 Hz Fuse rating: 32 A (?) Dimensions and Weight Overall length: 3,300 mm Overall width: 2,300 mm Overall height: 2,300 mm Overall weight: 7,700 kg Operating Data Machine operating time: 275 d 5 h 13 min 39 s Spindle operating time: 11,297 h 20 min 11 s EQUIPMENT - Full enclosure - Dust and fluid-proof guides - Oil mist extraction Iedpfjzqupxox An Notk - Compressor cooler - Frequency inverter - Heidenhain glass scales in X, Y, and Z axes - Work light in the interior - Technical documentation - Workbench - HSK-E-40 tool holders - Tools - Workbench dimensions: approx. 1,500 × 900 × 1,100 mm External Reference: Demo - Lot 2

Condition: used, Year of construction: 2018, functionality: fully functional, machine/vehicle number: SN 018-0212, travel distance X-axis: 4,000 mm, travel distance Y-axis: 580 mm, travel distance Z-axis: 700 mm, spindle speed (max.): 2,200 rpm, spindle speed (min.): 140 rpm, rapid traverse X-axis: 20 m/min, rapid traverse Y-axis: 6 m/min, rapid traverse Z-axis: 6 m/min, controller model: Penta-Tec, overall weight: 6,000 kg, nominal power (apparent): 12 kVA, number of slots in tool magazine: 10, We are offering this used BAUER Bohrmax Z40 vertical machining center, manufactured in 2018, for sale. Manufacturer: BAUER Model: Bohrmax Z40 Year of manufacture: 2018 SCOPE OF DELIVERY / TECHNICAL DATA: Iodpszlp T Iefx An Netk • Spindle speed range: 140-2200 rpm • Drive for X, Y, Z axes: servo motor • Rapid traverse X-axis: 20 m/min • Rapid traverse Y-axis: 6 m/min • Rapid traverse Z-axis: 6 m/min • Distance from top of table to bottom of tool holder: 700 mm • Tool holder: SK40 • Tool changer for 10 tools • T-slots: M12 • Drilling diameter: 3-32 mm • Thread drilling: M4 - M24 • Tolerance X-axis: ± 0.1 mm • Tolerance Y and Z axes: 0.06 mm • Drive motor for spindle: 7.5 kW • Light curtain at the front • Control: Touchscreen 18” • Chip conveyor with slat conveyor additional integrated equipment: • Automatic tool length measurement • Handheld control unit RCS01 • Software extension for pendulum operation + DXF package • Universally controllable hydraulic clamping system with 8 clamping points (manufacturer Polund - Pro-Clamp Systems) If you have any questions or require further information, please send us a message or call us.

Condition: ready for operation (used), Year of construction: 2016, operating hours: 152 h, functionality: fully functional, machine/vehicle number: 665182, travel distance X-axis: 650 mm, travel distance Y-axis: 550 mm, travel distance Z-axis: 500 mm, spindle speed (max.): 42,000 rpm, number of slots in tool magazine: 40, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Travel distances Travel distance X-axis: 650 mm Travel distance Y-axis: 550 mm Travel distance Z-axis: 500 mm Feed rates Feed rate X-axis: 30 m/min Feed rate Y-axis: 30 m/min Feed rate Z-axis: 30 m/min Spindle Spindle interface: HSK-E 40 Spindle speed: 42,000 rpm Spindle running time: 151 h 20 min 08 s Spindle replacement: 2025 Iedpfx Aezquqcjn Njtk Cost of spindle replacement: approx. EUR 40,000 Tool magazine Number of tool slots: 40 Pallet system Pallet dimensions: approx. 320 × 320 mm Pallet clamping: Rotary table MACHINE DETAILS Machine type: CNC machining center Manufacturer: OPS INGERSOLL Model: SPEED HAWK 650 Year of construction: 2016 Electrical connection data Mains voltage: 400 V Mains frequency: 50 Hz Control voltage: 24 V DC Maximum fuse rating: 63 A Connected power: 38 kVA Dimensions and weight Overall height: 2,850 mm Overall length: 3,300 mm Overall width: 2,400 mm Machine weight: 9,000 kg EQUIPMENT Technical documentation Manual HSK-E 40 tool holders 3 pallets

Condition: good (used), Clamping plate with T-slots, plate field, welding table, welding table, plate boring machine, T-slot plate, Isdpfxjrfzt Ne An Njtk -T-slot plate: clamping plate with support ribs and table extension on both sides -Clamping surface: 1800 x 1000 mm -Height: 840 mm -Groove width: 30 mm -Transport dimensions: 1820/1010/H840 mm -Weight: 660 kg

Condition: excellent (used), Aventics CKP-DA-032-0200-CL-MM00S00BLP000P0P0 Carriage Cylinder, slotted cylinder Item condition: Used, in perfect condition More slide cylinders - new and used - you will find in our store! International shipping costs on request! Itjdpfx Aolkbmfsn Njk

Condition: good (used), machine/vehicle number: 26041, Offer 26041 Technical data (approx.): Itodeyvrx Ropfx An Njk - Plate length approx.: 3000 mm - Plate width approx.: 2500 mm - Plate height without base frame approx.: 180 mm - Plate height with base frame approx.: 810 mm - Top plate thickness approx.: 115 mm - 11 T-slots in the table surface, length: 1500 mm - T-slot pitch in the table surface: 250 mm each - T-slot width approx.: 40 / 22 mm - T-slot depth approx.: 16 / 24 mm - Required space: L 3500 x W 2500 x H 1100 mm - Weight approx.: 4500 kg

Condition: used, Year of construction: 1978, throat 1410 mm Iedpfjyqvgtox An Njtk workpiece height max. 1150 mm stroke 1400 mm table diameter 1400 mm milling-head swivable +/- 10 ram - range of adjustment 750 mm pulling power 50000 N workpiece weight 10000 kg Ram stroke speed 30 m/min The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team

Condition: used, Second-hand Stark type 123 router bits for professional use in woodworking. These router bits are suitable for typical machining tasks carried out on this type of machine and can be viewed by arrangement. Further technical specifications and details of their exact condition will be provided on request. Itsdozryn Nspfx An Nsk