Used Veneer Vacum Press for sale (12,820)

Condition: used, Year of construction: 2017, Automatic cold press Manufacturer: CMB Type: PFR-CCL Year of manufacture: 2017 Technical data: Motorized loading table 3,500 x 1,600 mm for manual assembly of the plates and automatic loading into the press on the 1,600 mm side. Structure made of welded steel profiles. Devices for adjusting the working height to compensate for unevenness in the floor. Steel rollers. Foot switch. PRESS Plate size: 5,500 x 1,600 mm Loading side: 1,700 mm Stroke: from top to bottom Opening: 450 mm Cold press The plates are made of steel sheet and attached to a steel frame structure. Maximum pressing force: 160 tons. Specific pressure (on 100% of the area): 1.82 kg/cm2 Specific pressure (on 80% of the area): 2.27 kg/cm2 Pressure cylinder: 12 x 80 mm Auxiliary cylinders: 6 x 50/30 mm Power supply: 400 Volt EU/50 Hz/3 PH. + G AUTOMATIC LOADING and UNLOADING of the plates on the lower plate, on the 3,500 mm side. The transport is carried out via a motorized MYLAR belt. The belt is activated by 2 rollers, one of which is located at the entrance and one at the exit of the press. The rollers are driven by a motor with a chain that slides on special guides. The Mylar belt rotates around the lower plate, which rests on special side supports. The belt rotates on 2 rollers, which are located at the entrance and exit of the press. The ends of the MYLAR belt are attached to special rods with devices for tensioning the MYLAR. The upper plate is covered with a Mylar film. The press plates consist of thick steel sheets that are welded to the frame structure. HYDRAULIC UNIT with pump, oil tank and valves for operating the pressure cylinders and auxiliary cylinders that move the upper plate. The hydraulic control unit is located in the upper part of the press to facilitate maintenance. CONTROL PANEL with buttons and switches. Pressure control manometer on the front of the press. UNLOADING MOTORIZED ROLLER TABLE 2,000 x 1,600 mm The unloading table is located at the exit of the press for manual unloading of the pressed plates. Lrsdezuzw Dspfx Afwor Exit side from the press: 1,600 mm. Note: The loading table of the press with the dimensions 3,500 x 1,600 and the unloading table with the dimensions 2,000 x 1,600 are shorter than the press table with the dimensions 5,500 x 1,600, as the press was installed in a line. Note: The technical data and descriptions are a transcript of the order confirmation at the time. The data is for informational purposes only and is not binding.

Condition: used, Veneer machine Manufacturer: Fischer & Rückle Lrodpfx Aszuzptefwer Type: FZR 21 Year of manufacture: 2015 For the most efficient edge gluing of parallel-connected veneer strips into continuous or component-specific veneer surfaces. The cut or rotary-cut veneers must be pre-glued with PVAc or UREA adhesives. This edge feeding joining apparatus is the most economical alternative to longitudinal joining apparatuses for cross-grain applications. Production Approx. 17-20 joints/min. Technical data Veneer strip lengths (grain direction): 350-2150 mm Veneer strip widths (cross-grain direction): 50-600 mm Veneer surface width (cross-grain direction): min. 260 mm Veneer strip thickness: 0.3-1.5 mm Equipment Feeding device for efficient and convenient semi-automatic feeding of veneer strips Panel Automatic for component-specific surfaces with pre-sorted components and a pre-selected number of veneer strips. Features - The Furnimaster-plus has a veneer alignment function (reverse transport movement) - Perfect joining of cut or rotary-cut veneer of all wood species, even with wavy or rippled veneer - Unique, proven horizontal pressing system that results in fully closed, strong glue joints - Solid, robust construction for high durability, reliable and fail-safe operation - Easy operation thanks to touchscreen panel, clear symbols, separate manometers with direct access, etc. - Liftable pressure bars for quick and easy access to the heating plates for cleaning - Few wear parts, low costs for service and maintenance Cross cutter For cutting to a pre-set format width (across the grain) directly after splicing. Short widths can be pre-set and measured with the integrated encoder. Larger widths are determined by two photoelectric sensors that are mounted at the required distance from the clipper on the direct stacking device. Direct stacking device DA-12R, belt system For unloading and stacking the veneer surface directly after joining. The joined surfaces are gently unloaded and stacked on this compact direct stacking device without any mechanical impact. Min. veneer sheet length (grain direction): 350 mm Veneer sheet widths (across the grain): 250 - 1200 mm Max. stack height: 500 mm Max. stack width (across the grain) for unloading to the rear end: 1200 mm Note: The technical data and descriptions are taken from the original order confirmation. The data is for informational purposes only and is not binding. Another Fischer & Rückle machine, type: FZR 21, year of manufacture: 2009, is also available.

Condition: used, Year of construction: 2025, total length: 1,200 mm, total width: 800 mm, total height: 1,800 mm, Colour: Blue Empty weight: 450 kg Price: On request Lredpfx Asztxn Refwsr - Year: 2025 - Documentation available: Yes - CE marking present: Yes - CE certificate present: Yes - Serial number: PB12093N2025005 - Operating hours: 0 - Drive system: Conventional - Vertical/Horizontal: Horizontal and vertical - Number of rolls [pcs.]: 3 - Power [kW]: 1.5 - Shaft diameter [mm]: 50 - Top roll diameter [mm]: 155 - Bottom roll diameter [mm]: 155 - Bending speed [mm/min]: 11 - Capacity diameter round [mm]: 50 - Options: Digital readout - Transport dimensions: 1200mm x 800mm x 1800mm (l x w x h) - Transport weight [kg]: 450kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 2007, Heating plate press Ljdpfx Ajzuzxnefwjrr Manufacturer: OTT Type: Solid 16-32 Year of manufacture: 2007 Technical data Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2009, - Veneer strip lengths (fiber direction): 350-1500 mm - Veneer strip widths (cross-fiber direction): 50-500 mm - Veneer surface width (cross-fiber direction): min. 260 mm - Veneer strip thickness: 0.3-1.5 mm Veneer machine with direct stacking Manufacturer: Fischer & Rückle Type: FZR 15 / DAR 22 Year of manufacture: 2009 Cross-feed splicer For the most efficient cross-gluing of parallel-joined veneer strips into endless or component-specific veneer surfaces. The cut or rotary-cut veneers must be pre-glued, using PVAc or urea adhesives. This cross-feed splicer is the most economical alternative to longitudinal splicers for cross-fiber applications. Production Approx. 17-20 joints/min Technical data Veneer strip lengths (fiber direction): 350-1500 mm Veneer strip widths (cross-fiber direction): 50-500 mm Veneer surface width (cross-fiber direction): min. 260 mm Veneer strip thickness: 0.3-1.5 mm Equipment Feeding device for efficient and convenient semi-automatic feeding of veneer strips. Panel automatic for component-specific surfaces with pre-sorted components and a pre-selected number of veneer strips. Features - Perfect bonding of cut or rotary-cut veneer of all wood species, even with wavy or undulating veneer Lrsdpfx Afjzuz Hljwor - Unique, tried-and-tested horizontal pressing system that results in completely closed, solid glue joints - Solid, robust construction for a long service life, reliable and fail-safe operation - Easy operation thanks to screen, clear symbols, separate pressure gauge with direct access, etc. - Liftable pressure beams for quick and easy access to the heating plates for cleaning - Few wear parts, low costs for service and maintenance Cross-cutter For cutting to a pre-set format width (across the fiber direction) immediately after splicing. The straight alignment of the veneer must be observed and, if necessary, corrected by pressing a button. When working in endless mode, the required distance to the direct stacking device is set. Direct stacking device DAR-22 For outputting and stacking the veneer surface immediately after splicing or cutting. The spliced surfaces are gently output and stacked without this compact direct stacking device exerting any mechanical forces. Min. veneer sheet lengths (fiber direction): 350* - 1500 mm Veneer sheet widths (across the fiber direction): 260 - 500* - 2200 mm Stack removal from the left, right, or rear Max. stack height: 500 mm *Reliable stack alignment not guaranteed Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Veneer machine with direct stacking Manufacturer: Fischer & Rückle Type: FZR15 / DAR 12 Year of manufacture: 2006 / 2014 Cross-feeding splicer For highly efficient cross-gluing of parallel-joined veneer strips into endless or component-specific veneer surfaces. The cut or rotary-cut veneers must be pre-glued with PVAc or urea adhesives. This cross-gluer is the most economical alternative to longitudinal gluers for cross-grain applications. Production Approx. 17-20 joining points/min Technical data Veneer strip length (grain direction): 350-1500 mm Veneer strip width (cross-grain direction): 50-500 mm Veneer strip thickness: 0.3-1.5 mm Equipment Feed device for efficient and convenient semi-automatic feeding of veneer strips. Plate automation for component-specific surfaces with pre-sorted components and a pre-selected number of veneer strips. Features - Perfect bonding of cut or rotary-cut veneer of all wood species, even with wavy or rippled veneer - Unique, tried-and-tested horizontal pressing system that results in fully closed, solid glue joints - Solid, robust construction for high durability, reliable and fail-safe operation - Easy operation thanks to screen, clear symbols, separate manometer with direct access, etc. - Liftable pressure bars for quick and easy access to the heating plates for cleaning - Few wear parts, low costs for service and maintenance Cross cutter For cutting to a pre-set format width (across the grain). The width is determined by two photoelectric cells that are mounted at the required distance from the cutter. Direct stacking device DAR-22 Ljdozuz Hfopfx Afwjrr For outputting and stacking the veneer surface directly after splicing. The spliced surfaces are gently outputted and stacked on this compact direct stacking device without mechanical intervention. Min. veneer sheet length (grain direction): 350 mm Veneer sheet width (across the grain): 250 - 1200 mm Max. stack height approx. (small sheets are not perfectly aligned): 500 mm Max. stack width (across the grain) for discharge to the rear end: 1200 mm Note: The technical data and descriptions are a transcript of the original order confirmation. Data is for informational purposes only and is not binding.

Condition: good (used), HFS-210 Hot Stamping Press The machine is in perfect condition. Year of manufacture: 2019. Description: The HFS-210 Hot Stamping Press is a pneumatic hot stamping press for hot stamping, embossing paper, and plastics. A useful device in any advertising agency or digital printing house. The cycle is operated manually. The pneumatic drive ensures repeatable work and very high die pressure on the material. The machine is equipped with an automatic foil feed, which significantly shortens the time of a single hot stamping cycle, a worktop, adjustable embossing depth, a hot plate ground to 0.01 mm accuracy, which significantly improves the quality of embossing with large dies, a control panel, and modern OMRON controls. Specifications: MODEL: HFS-210 Hot Stamping Press Heating plate size: 210 x 150 mm Work table area: 500 x 350 mm Heating temperature control: via display up to 200°C Lsdpozt H U Sefx Afwsrr Holding foil adjustment: Automatic, potentiometer-controlled Hot plate pressure mechanism: pneumatic Height of the gilding stack: 68 mm Press force: 0.6 T Power consumption: 900 W Power supply: 230 V Machine dimensions: 750 mm (W) x 530 mm (D) x 1670 mm (H) Machine weight: 120 kg The machine includes a cross table and a die mounting frame. An instruction manual is included.

Condition: used, Bending tool, die, upper knife, upper tool, straight tool -Tool for: press brake Ledpfxsc Sauqe Afwsrr -Tool radius: 10 mm -Thickness: 20mm -Total length: 471 mm -Total height: 188 mm -Recording width: 80 mm -Weight: 19.8 kg

Condition: used, Bending tool, die, upper knife, upper tool, straight tool Lrodpfx Afjc Spnbowor -Tool for: press brake -Tool as: die -Thickness: 25/13 mm -Drawing with the pictures -Total length: 200 mm -Total height: 188 mm -Weight: 6 kg

Condition: good (used), Profile bending machine, bending machine, flat iron bender, horizontal bending/straightening press -Bending/straightening press: hydraulic profile bending machine -Base: solid construction, mobile -Hydraulic unit: unfortunately without type designation -Piston rod: Ø 55 mm / stroke: 200 mm -Individual components: see photos Ljdpfxot Hmhle Afwsrr -Total dimensions: 1180/1060/H1000 mm -Weight: 445 kg

Condition: good (used), Veneer saw, veneer sawing machine, jointing cutting machine, fine cutting machine, fine cutting circular saw Lrodpfx Afob A Hnhowjr -Cutting length: 3000 mm -with extraction

Condition: used, Bending tool, die, upper knife, upper tool, deer foot tool -Tool: for press brake -Tool radius: mm -Dimensions: 30 x 169 mm Lsdpfxecn Rdve Afwsrr -Length: 2500 mm -Weight: 89 kg

Condition: good (used), Year of construction: 1988, Reaction vessel, batch system, solids separator, washing trough, painter's wash station, water treatment, tool and water cleaning, filter press, chamber filter press -Manufacturer: Poligrat, chamber filter press type 470-20/2 Lodpfxehvfzne Afwsrr -Model: 11 plates -Hydraulic cylinder: Stroke: 115 mm -Dimensions: 1315/920/H1720 mm -Weight: 580 kg

Condition: used, Bending tool, die, upper knife, upper tool, straight tool -Tool: split, for press brake -Tool angle: 90° -Drawing: in the photos -Dimension: 33 x 170 mm Lrjdpfx Asgph Arefwor -Length: 1485 mm (1 x 855/630 mm each) -Weight: 44.6 kg

Condition: used, Bending tool, die, lower knife, lower tool, prism tool, reversible prism, 1-part die block for die bending machine, die tool, hemming tool Lredpfx Asgwhvaefwer -Tool: for press brake, die / hemming tool -Measures: see drawing in the photos -Dimensions: 150/101 / H75 mm / 150/77 / H159 mm -Weight: 7.2 kg / 11.4 kg

Condition: used, Bending tool, die, upper knife, upper tool, straight tool -Tool for: press brake -Tool as: die -Thickness: 25/13 mm -Drawing: with the pictures -Total length: 400 mm -Total height: 108 mm -Weight: 6.5 kg Lodpfxsfcd Ims Afworr

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, pressing force: 225 t, stroke length: 200 mm, table length: 4,100 mm, overall weight: 15,000 kg, Equipment: safety light barrier, Fully Serviced Bystronic CNC Pressbrake Available for Purchase Lrodpezg Nq Nsfx Afwer A high-quality, pre-owned Bystronic Xact Smart 225/4100 hydraulic downstroke CNC pressbrake is currently available for sale. This 2019 machine is fully serviced, operational, and ready for immediate deployment. Key Technical Specifications Manufacturer: Bystronic Model: Xact Smart 225/4100 Year of Manufacture: 2019 Bending Capacity: 225 tons Bed Size / Working Length: 4,100 mm (4 metres) Control System: ByVision touchscreen CNC control Total Axis Configuration: 7 axis total, featuring a 5-axis backgauge (X, X1, R, Z1, Z2) Crowning: Hydraulic deflection compensation Installation Requirement: Free-standing design; no foundation pit required Core Advantages High Precision: The 5-axis backgauge and hydraulic crowning ensure exact bending angles across the entire 4-metre bed length. User-Friendly Interface: The intuitive ByVision touchscreen control simplifies setup and reduces programming time. Cost-Effective Installation: The free-standing configuration eliminates the need for expensive floor excavations or pits. Feel free to let us know if you would like us to draft a formal quotation for you

Condition: used, Year of construction: 2017, Used 3-meter press brake from Safan Type: E Brake 100 3100 Capacity: 3100 x 100 tons Ledpfjzh Ibvox Afwjrr Y1, Y2, X, Xdelta, R, Z1, and Z2 are CNC-controlled E Control Hydraulic WILA top clamping system 1 set of complete tooling Year of manufacture: 2017

Condition: new, pressure 28.0 t throat 225 mm Lrsdpozkl Husfx Afwjr stroke 150 mm table surface area 325 x 300 mm work speed 2.0 - 9.8 mm/sek return speed 12.8 mm/sek total power requirement 4.0 kW weight of the machine ca. 650 kg dimensions of the machine ca. 1800 x 900 x 2000 mm - NC control to adjust the piston stroke - Selector switch for manual or semi-automatic operation - Flow control valve and pressure control valve - Integrated pressure gauge - Various tools can be installed on the piston - inside There is a 40 mm hole for attaching the tools

Condition: excellent (used), Year of construction: 2005, functionality: fully functional, pressing force: 100 t, stroke length: 215 mm, table length: 4,100 mm, Equipment: CE marking, High quality fully serviced Bystronic 4metre cnc pressbrake for sale Lsdszdgnnepfx Afwjrr PR100 100 x 4100 Make: Bystronic Edwards Pearson Model: PR 100 Pressure Reference Year / new: 2005 Total axis: 4 – 2axis back gauge X R – complete with 2 additional fingers on the back gauge, 4 fingers in total. With built in hemming table for producing sheet metal flashings or safety edges on sheet metal Hydraulic crowning Free standing no pit required Capacity / bed size / tonnage: 4metre x 4100mm x 100ton Cnc control: Cybelec Modeva 10S control Max stroke 215mm Rapid approach 180mm/s Bending cycle 10mm/s Rapid return 150mm/s

Condition: excellent (used), Year of construction: 2001, machine/vehicle number: 1301, power: 11 kW (14.96 HP), pressing force: 150 t, stroke length: 200 mm, table width: 100 mm, clearance between the columns: 400 mm, total length: 5,200 mm, total width: 1,730 mm, total height: 3,240 mm, overall weight: 10,500 kg, Equipment: CE marking, Adjustable sheet metal support arms, front side Parking station for sheet metal support arms, left side WILA crowning system Under power Ljdpfx Aezl Ahrjfworr Max. bending length: 3100 mm Distance between uprights: 2550 mm Max. pressing force: 150 tons Distance to table mount: 590 mm Max. stroke: 200 mm Table width: 100 mm Upright overhang: 400 mm Descent speed: 300 mm/min Working speed: 10 mm/min Return speed: 120 mm/min X-axis range: 0 - 1000 mm Number of controlled axes: 6 Crowning: Yes Power: 11 kW Length: 5200 mm Width: 1730 mm Height: 3240 mm Weight: 10500 kg

Condition: ready for operation (used), Year of construction: 1991, functionality: fully functional, power: 17 kW (23.11 HP), pressing force: 220 t, stroke length: 180 mm, throat depth: 420 mm, total width: 3,650 mm, total height: 2,900 mm, overall weight: 17,900 kg, Hydraulic press brake Manufacturer: AMADA, Type: HFB 220-30 H Year of manufacture: 1991 Lrjdpfxey T R Ryo Afwor Technical data Manufacturer: AMADA Type: HFB 220-30 H Year of manufacture: 1991 Press force: 220 tons Bending length: 3100 mm Stroke: max. 180 mm Overhang: 420 mm Distance between side supports: 2750 mm Power: 17 kW Dimensions: L 3,65 m, W 1700 mm, H 2900 mm Weight: 12.9 t Equipment • Delem DA 58 2-D graphics control system • Controlled axes: Y1, Y2, X, R1, R2, Z • Large tool package, see photos • Amada quick-release tool clamping system All information is provided without warranty. A live demonstration is possible at any time in our showroom.

Condition: good (used), Year of construction: 2020, functionality: fully functional, Horizontal baling press Dixi 80 SLD, with lifting/tilting device, semi-automatic, year of manufacture 2020 Manufacturer: Dixi Type: Dixi 80 SLD Year of manufacture: 2020 Drive power: 11 kW, 400 V / 21 A Feed opening: 1,040 x 1,110 mm (W x L) Lsdpfx Afeziy Dfswerr Pressing force: 80 t Pressing cycle: approx. 35 s Capacity: approx. 1000 kg/h Bale size: 1,120 x 1,120 x 1,200 mm (W x H x L) Bale weight: approx. 500-600 kg Tying: 4-fold, manual Machine dimensions: approx. 4,320 x 1,830 x 2,620 mm (L x W x H) Machine weight: approx. 8,000 kg Materials: Paper, cardboard, film Note: The press is in good condition. It has been inspected and tested. A video can be found on our website or YouTube channel. The operating manual is available. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided and any errors that may occur. The offer is subject to change, prior sale, and can be revoked at any time. Inspections are possible by arrangement. The sale is made against advance payment, ex works, without any warranty.

Condition: good (used), Year of construction: 2012, functionality: fully functional, Bale press Dixi 60 SLD, year of manufacture 2012 Manufacturer: Dixi Type: Dixi 60 SLD Year of manufacture: 2012 Drive power: 7.5 kW, 400 V / 16.5 A Feed opening: 990 x 1,110 mm (W x L) Pressing force: 60 t Pressing cycle: approx. 47 s Bale size: 800 x 1,100 x 1,200 mm (W x H x L) Bale weight: approx. 370-410 kg Tying: 3-fold, manual Machine dimensions: approx. 4,150 x 1,725 x 2,035 mm (L x W x H) Lodpfozk A Rdjx Afwjrr Machine weight: approx. 5,420 kg Material: Paper, cardboard, film Note: The press is in good condition. It has been inspected and tested. A video can be found on our website or YouTube channel. An operating manual is available. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or for any errors. The offer is non-binding, subject to prior sale, and can be revoked at any time. Inspections are possible by arrangement. The sale is made against advance payment, ex works, without any warranty.

Condition: used, Year of construction: 2008, Overview Lrodpjzk Eqmjfx Afwjr This NIKO VP11e is a horizontal pneumatic (membrane) press for whole or destemmed grapes, built in 2008 by NIKO (Nikolaj Šraml s.p., Podnanos, Slovenia). The press is made entirely of stainless steel and runs a fully automatic, multi-stage pressing program once started: grapes are loaded through the two perforated cylinder doors or axially, an internal membrane inflates against the load to extract juice at progressively increasing pressure, and the cylinder rotates between stages to break up ("crumble") the pressed cake ahead of the next drain cycle. Juice drains into a wheeled collection pan under the cylinder with a pump connection; pomace is discharged by rotating the open door face-down over the pan. The press is mounted on castors for repositioning and remains still installed and under power at the seller's winery in Spain. It can be inspected in operation on request. Technical data - Manufacturer: NIKO (Nikolaj Šraml s.p., Podnanos, Slovenia) - Model: VP11e - Year of manufacture: 2008 - Machine type: horizontal pneumatic (membrane) press for grapes, mobile on castors - Cylinder volume: 1,100 L (cylinder Ø 920 mm) - Juice drainage pan (tina) volume: 450 L - Loading doors: 2, 640 x 420 mm each - Max. working pressure: 1.7 bar - automatic multi-stage program (pre-press 0.3 bar, then 0.8 / 1.2 / 1.7 bar for whole white grapes; 0.3 bar, then 0.8 / 1.2 bar for destemmed, fermented red grapes) - Integrated blower for membrane aspiration: -0.2 bar vacuum / +0.2 bar pressure - Power: 2.9 kW, single-phase 230 V (1/N/PE), 50 Hz - Mechanical protection: IP55 - Noise level: < 75 dB - Dimensions: approx. 2,520 x 1,270 x H 1,560 mm (with axial loading extension; 2,350 mm long without it) - Weight: approx. 430 kg Equipment - Pneumatic membrane pressing cylinder with integrated aspiration blower - Wheeled juice drainage pan with pump connection - Electric control panel with automatic pressing programs (incl. draining cycle) - Axial loading option - Safety guard on drive elements, door interlock switch and STOP switch - OEM operating manual (Spanish) Condition Used - still installed and under power at the seller's winery. No further condition report has been provided by the seller; the machine can be inspected in operation on site. Availability Immediately. Location: Spain. Dismantling, handling, packing and truck loading can be quoted on request (EXW).