Used Wiring Diagrams for sale (3,297)

Year of construction: 1990, condition: excellent (used), functionality: fully functional, Very well preserved drying chamber system with 2 x 5 individual chambers. Year of construction 1990 and 2000. 8 units made by Brunner and Hildebrand and 2 units WSAB. See photos for dimensions. Drying chambers can still be viewed in operation until the end of September. Easy to dismantle as completely bolted! Complete with Lignomat control system. Control cabinets and wiring. Ihjdpfx Aot H I R Ujddet

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,000 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 45 kW (61.18 HP), year of last overhaul: 2025, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. Ihsdox A U Ncjpfx Addot • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see video for the machine function test.

Condition: used, Year of construction: 1969, weight 2 t stroke 500 mm ja ja Ihedpfxjwk Ravs Addjt

Condition: used, Year of construction: 2020, total length: 2,000 mm, total width: 2,500 mm, total height: 2,100 mm, Price: On request - Machine available from: 2025-12-15 - Year: 2020 Ihodpfsx Ad R Nox Addot - Documentation available: Yes - └ Type Documentation: Operating system, Technical data, User manual, Electrical diagrams - CE marking present: Yes - CE certificate present: No - Serial number: 1000040377 - Main motor power [kW]: 10 - Number of milling spindles [pcs]: 1 - Horizontal drilling unit: Yes - Horizontal drilling spindles [pcs]: 10 - Vertical drilling unit: Yes - Saw unit present: Yes - Voltage [V]: 400 - Current consumption [A]: 18 - Fuse [A]: 32 - Power [kW]: 10.0 - Transport dimensions: 2000mm x 2500mm x 2100mm (l x w x h) - Transport packages [pcs.]: 2 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: ready for operation (used), Year of construction: 2008, Brand: HSM Model: V-Press 1160 plus Year of manufacture: 2008 Pressing force: 532 kN Voltage: 400 V Maximum bale weight: up to 550 kg (depending on material) Bale dimensions: 120 x 110 x 120 cm Machine weight: 2,403 kg Machine dimensions: 180 x 157 x 298.5 cm Filling opening dimensions: 19.5 x 65 x 111.5 cm Condition: very good! Functionality thoroughly tested. Ijdjx Tznvopfx Addeht FLITS Rental & Sales service: with every machine, we supply a bundle of binding wire (120 wires). Do you need additional bundles of binding wire? Request a non-binding quote. At FLITS Rental & Sales, you can count on speed, transparency, and reliability. We think along with you, respond promptly, and ensure you have the right machine quickly. You are very welcome to view the machines at our location. We are located at Schoterlandseweg 94, 8413NE Oudehorne. Visits are possible by appointment, allowing us to provide comprehensive information and show you the right machines. We are happy to assist you! Waste baler Paper baler Cardboard baler Plastic baler Waste compactor Recycling Textile press Waste Waste processing

Condition: excellent (used), Year of construction: 2017, machine/vehicle number: SEM126/TH46098, Automatic Carton Folder Gluer, Max open blank width: 1100 mm, Min open blank width: 126 mm, Max feed up length: 800 mm, Min feed up length: 60 mm Stock : Cartonboard up to 800 gsm, Corrugated up to E flute.Max belt speed i: 425 m/min Complete with : Bottom belt feeder, Back lifters with vibration for smooth and consistent feeding, Pre-breaking system, Small box attachment - allowing min 76mm open blank width, Crash-lock module, Bottom left hand side glue pot, Three belt carrier folding section, Heavy duty Double Trombone delivery, Compression belt section, HHS C-1100 8 B cold glue system, 4 x HHS glue guns, Remote control, Manuals and electrical diagrams. Ijdpfxsv Ipl Ts Addjht

Condition: ready for operation (used), Year of construction: 2008, travel distance X-axis: 600 mm, travel distance Y-axis: 400 mm, travel distance Z-axis: 310 mm, controller manufacturer: FANUC, controller model: 310is-WA, number of axes: 5, This 5-axis FANUC Alpha 1ID wire EDM machine was manufactured in 2008. It offers precision and efficiency for intricate metalworking tasks. If you are looking to get high-quality EDM capabilities, consider the FANUC Alpha 1ID machine we have for sale. Contact us for more information. Additional equipment • Includes all accessories in the photos • Includes digital documentation Machine Benefits Technical Machine Benefits • Internal dimensions of the work tank: 1100 x 800 mm • Wire diameter: 0. 1 mm to 0. 3 mm (0. 25 mm present on the machine) • Wire spool capacity: up to 16 kg • Automatic wire cutting and feeding Iodpsyali Ajfx Addoht Extra Information Machine still under power

Condition: reconditioned (used), Year of construction: 2014, operating hours: 5,612 h, functionality: fully functional, pressing force: 48 t, filling opening width: 1,020 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 550 kg, total height: 2,800 mm, overall weight: 12,000 kg, transport height: 2,800 mm, oil tank capacity: 300 l, power: 30 kW (40.79 HP), volume flow: 332 m³/h, Technical information baler: Manufacturer HSM GmbH + Co. KG Typ VK 4812 Year of construction 2014 Hours of operation 5,612 hours, stand August 2025 Press power main press 48 tons Specific press capacity 58,2 N/cm² Feed channel 1,250 x 1,020 mm Theoretic cycle time 11.2 sec. Theoretic throughput rate 332 m³/hour Bale size 1,100 x 750 x 600 up to 1,200 mm Driving motor 30 kW Connected load 32 kW Rated current 59 A Tying system 4-fold horizontal, fully automatic Throughput rate at a Iedpfx Adsvtpq Hsdjht bulk weight of 20 kg/cbm up to 6 tons/hour bulk weight of 50 kg/cbm up to 13 tons/hour Bale weight up to 550 kg, depends on material SPS controller Siemens SIMATIC S7-200 Operating panel Siemens HMI Touch Panel Filling quantity hydraulic oil tank 300 L Oil type HVI 46 Machine installation dimensions with bale chute 10,046 x 4,387 x 2,705 mm (l x w x h) Transport dimensions baler 8,500 x 2,500 x 2,750 mm (l x w x h) Machine weight press approx. 12 t Scope of delivery: Baler HSM VK 4812, without hydraulic oil, without conveyor system. Two wire reel boxes for 8 pieces 40 kg wire reels, without wire Bale chute Machine documentation in German Comments: The press is equipped with an oil cooler and potential-free contacts for external control. The control cabinet is operated from the left in the direction of pressing, the needle unit is located on the right-hand side and can be folded back for transport. The press was partially overhauled and tested in our workshop, see photos and our function video. The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagrams) is available in German. Viewing is possible by appointment. We accept no liability for the technical details or any errors.

Condition: excellent (used), Year of construction: 1979, functionality: fully functional, Wire diameter range: up to 500 N/mm² 22 - 7,0 mm up to 1.000 N/mm² 21 - 8,0 mm Iedpsyak Eisfx Addsht over 1.000 N/mm² 20 - 8,0 mm Number of kalibers: 10

Condition: repair required (used), - Shredder Lindner Komet 1750 - one motor with 160 kW - Without electrical cabinet and hydraulics. Ihjdpfx Adjx Szf Ejdot - With all manuals. Electric and hydraulic diagrams.

Year of construction: 2017, condition: used, functionality: fully functional, machine/vehicle number: E11SI17062595708, This listing is for a Rational SCC 101 WE combi steamer in electric version, from the premium manufacturer Rational. The unit comes from the SCC series, featuring triple glazing and LED lighting. The combi steamer has been inspected in our in-house workshop and is fully functional. The underframe shown in the pictures is not included in the offer, but can be purchased separately as an option. RRP: €12,920 net. You will receive an invoice with VAT shown separately. Service: We are happy to assist with arranging a certified Rational customer service technician. Are you looking for a specific Rational appliance type? Feel free to ask—we have access to an extensive range of new and used equipment. We are happy to advise you on all appliance types. Our used equipment service for you: - 6 months warranty on electrical parts, limited to replacement of defective parts, excluding installation and removal costs - High-quality branded equipment at fair prices - Professional refurbishment / inspection & expert cleaning - Tested & fully functional - or your money back - Flexible shipping or self-collection options - Competent advice – before and after purchase - Provision of operating manuals, wiring diagrams & spare parts - DGUV V3 safety inspection Iedpfx Ajx U Snvoddeht This combi steamer accommodates 10 x 1/1 GN containers. In automatic mode, the unit independently detects the ideal cooking path, product size, load quantity, and product-specific requirements for 7 applications (meat, fish, poultry, side dishes, egg dishes, baked goods, and finishing). Technical data: - WxDxH: approx. 847 x 776 x 1042 mm - Minimum door opening for delivery WxH: 845 x 1050 mm - Power connection: 400 V / 18.6 kW / 50-60 Hz - Capacity: 10 x 1/1 GN - Weight: approx. 132 kg - Serial number: E11SI17062595708 - Year of manufacture: 2017 Condition: used, fully operational Additional features: - 3 operating modes in combi-steamer mode: steam (30°C to 130°C), hot air (30°C to 300°C), and combination (30°C to 300°C) - Care Control - self-cleaning program - Core temperature probe - Hand shower with automatic retraction - 8.5" color display and touchscreen - 5 programmable fan speeds - Integrated, maintenance-free grease separation system - Automatic start time preselection - 7 cleaning levels for unattended cleaning – including overnight cleaning - 3-stage steam injection, adjustable from 30°C to 260°C - 5 programmable fermentation levels - USB interface - Seamless, hygienic cooking chamber with rounded corners - Halogen cooking chamber lighting Shipping: - Delivery or self-collection by arrangement - Worldwide shipping on request - Shipping to islands or mountain stations only by prior arrangement Subject to change and error. Do you have questions, need advice, or would like to view the equipment on-site? You can reach us by phone during our business hours: Monday to Friday, 9:00–13:00 and 14:00–17:00. Sales are made exclusively according to our general terms and conditions (GTC).

Condition: new, Year of construction: 2021, functionality: fully functional, Stock machine "NEW" – available at short notice! (Subject to prior sale) Control: Fanuc 0i-MF Plus, 10.4" with Manual Guide i & 2 MB NC memory LOOK-AHEAD function, 400 blocks Machine Table: Table size: 950 x 550 mm Load capacity: 800 kg T-slot width: 18 mm Number of T-slots: 3 Distance between T-slots: 150 mm Travel axes: Travel X/Y/Z: 860/550/550 mm Spindle nose to table surface: 150 – 700 mm Linear guides & speeds: Ball linear guides in X/Y axes Roller linear guide in Z axis Rapid traverse X/Y/Z: 40/40/30 m/min Feedrate during milling: 0 – 10,000 mm/min Smallest increment: 0.001 mm Tool magazine (CAM-Type) / changer: Number of magazine pockets: 30 System: random access Max. tool diameter: Ø 75 mm Max. tool diameter with adjacent pockets free: Ø150 mm (40 tools: Ø130 mm) Max. tool length: 300 mm Max. tool weight: 7 kg Spindle: Spindle taper: SK-40 Drive power (30min/cont.): 18.5/11 kW 15,000 rpm direct-drive spindle Spindle oil cooler Ijdpfx Adoifn N Nsdeht Coolant, chip, and compressed air management: Coolant system incl. 300 liter tank and pumps External coolant around spindle Chip augers right and left in machine bed Compressed air nozzle at spindle (M32/M33) Compressed air through spindle (M38/M39) Compressed air and coolant gun Other features: Swiveling operator panel Electronic handwheel (wired) Central lubrication oil/air Full enclosure Work light Heat exchanger at control cabinet Auto power-off function Hand tool set Signal lamp Transformer 400 VAC, 50 Hz CE declaration of conformity according to European directives Electrical and pneumatic requirements: Electrical connection: 36 kVA Required pneumatic input pressure: 6 bar Dimensions: Machine size: W2,260 x D2,900 x H2,775 mm Required installation area: W3,160 x D3,000 x H3,000 mm (incl. chip conveyor ejection to the left) Machine weight: approx. 5,400 kg (net) Available special equipment: Spindle: - Direct-driven spindle SK-40, 15,000 rpm - Drive power (30min/cont.): 18.5 / 15 kW, (FANUC motor) Tool magazine / changer: - Drum-type tool magazine with 30 pockets, DIN69871, SK-40 Rotary or additional axes: - Preparation for 4th axis (FANUC controls), incl. wiring and Harting connector, without axis drive Coolant, chip, and compressed air management: - Bed flushing - Through-spindle coolant pump, 20 bar pressure, for direct-driven spindles - Includes cartridge filter - Belt-type chip conveyor including chip cart (chip discharge at front, to the left side of the machine) Measuring and monitoring systems: - RENISHAW OMP-60 probe with infrared transmission system for workpiece measurement, incl. probe holder, repeatability: 1μm - RENISHAW NC4+ tool laser measurement system and tool breakage monitoring in the machine, incl. bracket - Auto-door (side door) - Pneumatic interface for workpiece clamping - Clamping devices as shown With RoboJob Mill Assist 25kg (Year of construction 2025 – NEW) - Full enclosure - Double gripper Available immediately

Condition: ready for operation (used), Year of construction: 2016, number of axes: 6, This 6-axis CLOOS QRC 350 QIROX welding robot was manufactured in 2016. It features a maximum load capacity of 15 kg, a workstation reach of 3400 mm, and advanced V6 control. Equipped with a 450A Qineo Pulse A welding machine, it ensures precise and efficient welding. The robot includes a touch sensor and an arc sensor for enhanced accuracy during operations. Consider the opportunity to buy this CLOOS QRC 350 QIROX welding robot. Contact us for more information about this machine. Additional equipment • Premium control panel with wall bracket and cable holder • External gas cleaning device • Adjustable electro-pneumatic valve • Wire feed equipment Machine Benefits Technical Machine Benefits Ihsdpfx Aeyaliijddet • Built-in welding interface and software • Protective tube for wire transfer • High usability with movable counter-side support • Workstation: 3400 mm • Longitudinal track travel speed: 1. 8 m/sec • Longitudinal track travel length: 7000 mm • Qineo touch sensor: 60 v • Arc sensor for welding path adjustment Extra Information Includes standard height robot stool and computer connector for enhanced usability. Control Unit Control: V6 Advanced Digital inputs and outputs: 16 USB connectors: 2 Connectivity: Expandable up to 16 axes, CAN-Bus, serial interfaces

Condition: excellent (used), Year of construction: 2017, operating hours: 13,284 h, functionality: fully functional, pressing force: 140 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,500 kg, oil tank capacity: 2,600 l, Technical data baler: Manufacturer Bollegraaf Type HBC 140 Year of construction 2017 Working hours 13,284, as of October 2025 Press power main press 140 tons (max. 153,5 tons) Press power of pre-press 70 tons Feed channel 1,600 x 1,100 mm (l x w) Capacity per cycle time 4,34 cbm Theoretic cycle time 16 sec. Bale size 1,100 x 1,100 mm (w x h), length adjustable Driving motor 2 x 75 kW Connected load 209 kW Tying system 5-fold vertical, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx. 30 tons/h bulk weight of 50 kg/cbm approx. 46 tons/h bulk weight of 100 kg/cbm approx. 82 tons/h Bale weight 850 up to 1.500 kg Hydraulicoil 2.600 l Univis N46 Baler dimensions with conveyor built up with hopper approx.13,200 x 24,200 x 7,333 mm (l x w x h) Transport dimensions only baler approx.13,200 x 2,884 x 3,539 mm (l x w x h) Machine weight baler approx. 51,810 tons Technical data feeding and elevating conveyor with gooseneck: Manufacturer Bollegraaf Typ HBT 1216/1800 * 23,300 30°/15° Year of construction 2017 Driving motor 7,5 kW Length feeding conveyor 6,750 mm Length elevating conveyor 14,400 mm Length goose neck 2,150 mm Grade 30° Effecting width 1,754 mm Height of side wall feeding conv. 500 mm Height of side wall elevating conv. 800 mm Transport dimensions feeding conveyor with one segment elevating part 9,816 x 2,500 x 2,242 mm (l x w x h) Transport dimensions elevating conveyor with goose neck 13,472 x 2,800 (without motor) x 2,729 mm (l x w x h) Pit dimensions 10,000 x 3,200 x 1,200 mm (l x w x d) Condition: The press is in very good condition and ready for immediate operation, see the function video for more information. The conveyor belt chain needs replacing. The system will be in operation until December 2025. Scope of delivery: Ihodpfx Aexpxhvoddst baler with conveyor belt, maintenance platform, access ladder, two wire feed stations for 5 wire reels each (without wire), and bale slider. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: used, CNC press brake FASTI type 904-125/30 serial no. 95-904-5775 year of construction 1995 Pressure capacity 125 ton. Working length 3050 mm Stroke approx. 335 mm Stand projection 300 mm Clearance between the side uprights 2550 mm Tool installation height max. 465 mm (opening width between the tool holders) Table width 90 mm (the clamping system is mounted on the table) Table height above floor 875 mm (910 mm with clamping system) Backgauge X-axis 500 mm Backgauge R-axis 115 mm Backgauge Z-axis approx. 1950 mm Lowering speed Y rapid traverse 90 mm/s Lowering speed Y-operation 8.9 mm/s Return stroke speed Y-retraction 75 mm/s Oil filling approx. 160 liters Motor power 18.5 kW Ihedpfohmmfkex Addet Mains connection 400 Volt, 50 Hz, 20 Amp. - 7-axis CNC control DELEM type DA 58 with LCD screen - 1 axis for back gauge - stop depth (X-axis) - 2 axes for back gauge - fence height (finger R1 + finger R2) - 2 axes for back gauge - stop finger, laterally movable (finger Z1 + finger Z2) - 2 axes for press beam with servo valves and measuring system Y1 and Y2 - Operation via electric foot switch and 2-hand control panel or 2-hand control panel only - Hydraulic tool clamping for the TRUMPF upper tool system, with 20 mm clamping groove - Hydraulic tool clamping for the lower tool with 13 mm table groove, depth 21 mm (tool pin 13 x 20 mm) - FIESSLER safety light barrier, type AKAS - 2 material support arms at the front, manually movable to the side and height-adjustable - Electrical diagram, hydraulic diagram, user manual for control available - Control cabinet on the machine - without tools Space requirement L x W x H 5000 x 2500 x 3050 mm Transport dimensions L x W x H 5200 x 1900 x 2950 mm Weight 8.5 tons. Good condition

Condition: used, This listing is for a Labcold RLPR1514 Refrigerator The unit is in full working condition and is ready for immediate release The Labcold RLPR1514 is a Sparkfree Laboratory Refrigerator with a capacity of 400 litres, designed to safely store flammable materials by eliminating any sources of ignition within its chamber. Ihsdpfx Aoxhf U Teddst The Labcold RLPR1514 is a sparkfree laboratory fridge designed for safely storing volatile substances without any sources of ignition inside the chamber. It has a 400L capacity, fan-assisted cooling, and comes with plastic-coated wire mesh shelves. The fridge features a digital temperature display, alarms for high/low temperatures and door open alerts, and includes a fitted door lock. Specifications: External Dimensions: 1855h x 600w x 585d mm Internal Dimensions: W506 x D485 x H1620 mm Safety Features: Sparkfree safety interior Cooling & Defrosting: Off Cycle Automatic defrosting, fan-assisted cooling Shelves: 6 (including 2 adjustable shelves) Security: Key lock with two keys Temperature Range: 0°C to 10°C Alarms & Monitoring: High/Low temperature alarm Min/Max recording Door open alarm Door Type: Solid

Condition: new, Year of construction: 2025, - FANUC 0i-MF Plus "NEW" - 10.4" LCD color screen - Diagonal, MANUAL GUIDE i Machine Table - Table size: 1,120 x 560 mm - Load capacity: 1,000 kg - T-slot width: 18 mm - Number of T-slots: 5 - T-slot spacing: 100 mm - Table height from floor: 900 mm Travel paths and distances - X / Y / Z travel paths: 1,050 / 560 / 560 mm - Spindle nose to table surface: 150 - 710 mm - Spindle center to column: 600 mm Linear axis guides & speeds - Flat guides in X / Y / Z axes - Rapid traverse X/Y/Z: 36/36/34 m/min - Milling feed: 1 – 10,000 mm/min - Minimum increment: 0.001 mm Tool magazine (CAM type) / tool changer - Tool holder: BBT-50 (optional SK-50) - Number of magazine positions: 24 - System: random - Max. tool diameter: Ø 105 mm - Max. tool diameter with free adjacent positions: Ø200 mm - Max. tool length: 300 mm - Max. tool weight: 15 kg Spindle - Spindle taper: BTT-50 BIG-PLUS® (optional SK-50) - Drive type: 2-stage gearbox - Speed level 1: 80 - 1,500 rpm - Speed level 2: 1,500 - 8,000 rpm - Drive power (30 min/continuous): 11 / 7.5 kW - Torque (30 min/continuous): 236/161 Nm up to 369 rpm - Lubrication: Grease - Inner bearing diameter: Ø80 mm - Spindle cooling: Oil Coolant, chip, and compressed air management - Coolant system including 400-liter tank and pumps - External coolant around the spindle - Internal cooling 50 bar - Bed flushing, 0.85 kW / 130 l/min., (optional) - Chip spirals on the right and left side of the machine bed Chips are conveyed to the front of the machine - Chip spiral (optional: belt or scraper belt chip conveyor) Chips are conveyed to the left side of the machine - Compressed air nozzle on the spindle (M32/M33) Isdpfswkf Izjx Addoht - Compressed air through the spindle (M38/M39), (Optional) - Compressed air and coolant gun Other Equipment - Pivoting control panel - Electronic handwheel (wired) - Central oil/air lubrication system - Spindle oil cooler - Fully enclosed housing - Work light - Heat exchanger on the control cabinet - Auto-Power OFF function - Hand tool set - Signal light - Transformer 400 VAC, 50 Hz - CE Declaration of Conformity

Condition: ready for operation (used), Year of construction: 2018, operating hours: 7,931 h, travel distance X-axis: 1,016 mm, travel distance Y-axis: 660 mm, travel distance Z-axis: 635 mm, spindle speed (max.): 12,000 rpm, This 4-axis HAAS VF-3SSYT with HRT 210 4X was manufactured in 2018. It features a 12,000-rpm spindle, 30+1 side-mount tool changer, and through-spindle coolant at 300 psi. The machine includes a 4th-axis drive, wireless probing system, and high-speed machining capabilities. If you are looking to get high-quality milling capabilities, consider the HAAS VF-3SSYT machine we have for sale. Contact us for more information about this machine. Additional equipment • High-Speed 30+1 Side-Mount Tool Changer / Advanced Tool Management / Early Power-Failure Detection Module / Multi-Stage Coolant Pump / Rigid Tapping Safe Run / Media Display M-Code; M130 / Power Surge Protection / Window Air Blast / Visual Part Programming System / User-Definable Macros / Spindle Orientation / Coordinate Rotation and Scaling / Chip Tray Filter Kit / CT-Style Tool Changer Grippers / Through-Spindle Coolant, 300 psi (21 bar) / 4th-Axis Drive and Wiring / Wireless Intuitive Probing System / Chip Auger / Programmable Coolant Nozzle / High-Speed Machining / Large Remote Jog Handle with Touchscreen Display / High-Volt Transformer, Non-USA Machine Benefits Technical Machine Benefits • Spindle speed: 12000 rpm • Standard program memory: 1 gb / control widescreen monitor Isdpfx Aeyalh Ejddeht • Remote monitoring: haasconnect / ethernet interface / wifi connection for the haas control

Condition: used, Automatic lathe, turning machine with copy attachment UMA Type F1 NK 60 Copy lathe for chuck parts Machine no. 28-0031 Year of manufacture: 1971 Maximum turning diameter: 150 mm Swing diameter over bed: 400 mm Turning length: approx. 200 mm Spindle bore in machine spindle: approx. 42 mm Spindle speeds: 580 / 930 / 1480 / 2380 rpm, 4 steps Main motor power: 5.5 kW Electrical connection: 380 Volt, 50 Hz - Spindle flange for chuck mounting, short taper 55021, size 6, flange outer diameter Ø 180 mm - Spindle speed via 4 gearbox steps - Hydraulic clamping device with expanding mandrel, without spindle bore, clamping diameter Ø 15 mm - Right side with copying slide, copying unit SAUTER Type KMCA 61, with hydraulic feed movement - Left side with cross slide with hydraulic feed movement - Coolant system mounted below the machine bed - Hydraulic unit positioned behind the machine - Operating manual, electrical diagram, hydraulic diagram Space requirement automatic lathe with hydraulic unit (L x W x H): 2900 x 1900 x 1700 mm Space requirement automatic lathe (L x W x H): 2400 x 1900 x 1500 mm Space requirement hydraulic unit (L x W x H): 1400 x 850 x 1700 mm Weight automatic lathe: 2400 kg Weight hydraulic unit: 400 kg Ihjdpfxsib D H Re Addjt Total weight with pallet: 3000 kg In good condition

Condition: used, This listing is for the Agilent 34970a Data Loger Switch Unit The unit is in full working condition and is ready for immediate use Key Features: 3-slot mainframe: Supports up to 60 2-wire channels using plug-in modules. Built-in 6½-digit DMM (Digital Multimeter): Measures voltage, current, resistance, frequency, and temperature. Plug-in Modules Available: e.g. 34901A (20-channel multiplexer), 34902A (16-channel actuator), 34908A (40-channel single-ended multiplexer), etc. Interfaces: GPIB and RS-232 standard (USB via adapter). Ihedpfx Aexhfcdsddot Logging Capabilities: Can log data over time for test/monitoring applications. Scan Rates: Up to 250 channels/sec depending on configuration. User Interface: Front-panel controls with LCD display. Remote control via SCPI commands. Typical Applications: Environmental monitoring (temperature, humidity) Functional test systems Data logging in labs Automotive and aerospace test setups Industrial process monitoring

Condition: ready for operation (used), Year of construction: 2023, This CLOOS Instant pro IRPS was manufactured in 2023. It features a QIROX welding robot with a maximum payload of 10 kg and a working range of Ø 3900 mm. Equipped with advanced QC 2 control system, it includes a programming handheld device and supports new tandem leading/trailing processes. Ideal for high-quality welding applications, it also comes with a comprehensive set of welding and sensor technologies. Contact us for more information about this machine. Machine Benefits Technical Machine Benefits • Working range: Ø 3900 mm • Programming handheld device with touchscreen • Qirox technology interface • Tool controller ctms Ijdpfx Aeyaimleddeht • Tcp measuring device Extra Information Welding Technology Power source Arc sensor Water cooling module Control module Wire drive unit Robot welding torch Software Parameter grinding Distance-dependent transition between parameter lists Multi-layer technology Programmable pendulum figures Software language: German IRPS Scanner Control IPC Rittal control cabinet Touch screen Scanner interface Uninterruptible power supply Scan width: 1000 mm at 500 mm product height Scan speed: 300 to 1000 mm/sec Burner Cleaning Unit Torch cleaning device Compressed air amplifier Wire cutter Control Unit Digital inputs/outputs: 16 Serial interface Computer connection: QIROX controller CAN bus USB interfaces: 2 Flash memory: 8 GB Buffer module: 24V Point editor Expandable to up to 16 axes

Condition: used, CNC Universal Coordinate Drilling and Milling Machine FEHLMANN type PICOMAX 100-CNC 3 CNC control HEIDENHAIN TNC 155 make no. 16186651 year of construction 1986 spindle holder FEHLMANN SF32 drilling capacity Ø 30 mm in steel threading up to M20 in steel travel X: 850 mm, Y: 435 mm pinol stroke Z: 210 mm vertical movement milling head 580 mm Feed X and Y 1 to 8000 mm/min. Feed Z 1 to 4000 mm/min. Rapid traverse X and Y 8 m/min. rapid traverse Z 4 m/min. Table clamping surface 1570 x 500 mm distance spindle nose - table 130 - 720 mm projection spindle - column 450 mm Spindle speed 50 - 7100 rpm. Stepless spindle drive 10 kW Total connected power 20 kW Mains connection 400 Volt, 50 Hz - CNC control HEIDENHAIN TNC 155 with TFT monitor - 3 axes controlled, X, Y and Z pinol adjustment - hydro-mechanical tool clamping FEHLMANN SF32 - thread cutting device Iedpfxohik Ezo Addeht - cable remote control for machine operation and axis movements - motorized vertical movement of the milling head with shut-off via adjustable cams - 3D probe RENISHAW, type MP 11F with holder Fehlmann SF32 - 20 tool holders FEHLMANN SF32 - swivelling tool holder with 21 tool places - Coolant device in the machine column - control cabinet fixed to the machine - Documentation Operating manual, control manual and E-circuit diagrams space requirement L x W x H 2350 x 2000 x 2300 mm weight 3,2 ton. very good condition

Year of construction: 1998, condition: ready for operation (used), overall weight: 2,200 kg, This KASTO SSB 260 VA-CC-CNC Metal Band Saw was manufactured in 1998. A reliable choice for your cutting needs, it offers precision and durability. Consider the opportunity to buy this KASTO SSB 260 VA-CC-CNC Metal Band Saw. Contact us for more information. Additional equipment • Accessories: 18 saw bands (see photos) Machine Benefits Technical Machine Benefits • Dimensions of the entire system: length 2160 mm /width 2080 mm/ height 2030 mm / total weight approx. 2 200 kg • Total drive power approx. 6. 5 kw/ saw motor approx. 4. 0 kw/ cutting range round 260 mm /cutting area square 260 x 260 mm /smallest diameter to be sawn 10 mm /smallest cut-off length 5 mm • Minimum offcut length single cut 10 mm/ minimum offcut length in automatic mode 110 mm/ automatic material feed single max. 600 mm multiple material feed (up to 9x) 400 mm /belt speed: mm infinitely variable 15 - 125 m/min /cutting feed: infinitely variable /material feed: hydraulic • Automatic feed: with horizontal clamping /material clamping: hydraulic, infinitely variable /clamping force: horizontal vice (sp l) 150 - 800 dan /feed vice (sp ii) 150 - 800 dan • Saw blade dimensions 4115 x 41 x 1. 3 mm /saw blade guide: carbide, replaceable /saw blade tensioning: hydraulic saw blade cleaning: hydraulic with easily replaceable wire brush. Driven via flex shaft in the same ratio as the main drive driven. Isdpfoyaii Tex Addsht • Supply via coolant nozzle/ volume 100 1/ pump capacity 50 l/min. Extra Information Machine still under power

Condition: used, CNC Press Brake AMADA Type HFBO 50 x 2000 Serial No. HFBO 50 20 S60906 Year of manufacture: 1996 Ihjdpfx Adew Iq Ugedet Press brake with 8 axes - CNC control Operator II Pressing force: 50 tons Working length: 2090 mm Stroke: 200 mm Frame depth: 420 mm Distance between side frames: 1660 mm Max. tool installation height: 460 mm Table width: 60 mm Table height above floor: 910 mm Motor power: 4.5 kW Mains connection: 400 Volt, 50 Hz, 20 Amp. - 8-axis CNC control Operator II (Y1-Y2 / X1-X2 / Z1-Z2 / R1-R2) - 2 freely programmable backgauge fingers, movable laterally and in height (Z1+Z2+R1+R2) - Press beam with servo valves and measuring system Y1 and Y2 - Operation via electric foot switch and/or two-hand control panel - Mechanical lever-style tool clamping for the upper tool (5 AMADA Expert, 5 UKB 50.667 H=120 mm) - Tool holder for lower tool, 60 mm wide - 11-piece upper tool set, 30°, total length 1675 mm - consisting of: 1x 835 / 1x 300 / 1x 165 / 1x 50 / 1x 45 / 1x 35 / 1x 20 / 1x 15 / 1x 10 / 2x 100 mm (end pieces) in length - 2-piece lower tool, 88° - V8, total length 1250 mm - consisting of: 1x 835 / 1x 415 mm in length - Indicated operating hours: 30,537 h - Operating manual, electrical diagram, spare parts book included Weight: 4,700 kg Good condition

Condition: used, L + Z Lathe WEILER Type LZ PRIMUS GS Machine no. No. 2461 Year of construction approx. 1990 Center width 400 mm Turning diameter over bed 250 mm Center height above bed 125 mm Turning diameter over support 140 mm Center height above support 70 mm Spindle bore 24 mm Spindle speed 60 - 3000 rpm 18 steps Feed lengthwise and flat Chuck flange short taper DIN 55022 size 4 Inner tailstock taper MK 2 Drive power 1.1 kW and 1.5 kW pole-changing Mains connection 380 Volt, 50 Hz - 3-axis digital readout FAGOR, type 30i-T-B - Spindle speed via 2 motor speeds and 9 gear stages - 3-jaw lathe chuck RÖHM Ø 125 mm with stepped jaws - MULTIFIX quick-change tool holder with 1 interchangeable cassette - Set of collets Ø 1 / 3 / 4 / 5 / 7 / 8 / 10 / 14 / 15 / 16 / 17 / 19 / 20 / mm - 1 centering tip for collet chuck holder - Emergency stop - Hinged chuck guard - Splash guard - Machine light - electrical diagram - Machine mounted on a steel plate (steel plate L x W x H 1200 x 500 x 30 mm, 140 kg) Iodpfx Asrtd Uwjddsht Space requirement L x W x H 1200 x 900 x 1560 mm Weight 520 kg good condition