Cut-to-length line 1.500 x 3 mm/10 t

NN/ LISSE

Condition: used, Year of construction: 1977, pressure 250 t Ffodjvuuaijpfx Abueu stroke 40 - 190 mm no. of strokes 40 /min throat 500 mm passage to the back 1050 mm dayligth 615 mm table surface area 1380 x 880 mm hole in the table 450 mm table height over floor 800 mm ram surface 1200 x 800 mm ram adjustment 125 mm power requirement 22,0 kW Weight 24,0 t dimensions of the machine ca. 2,0 x 2,5 x 3,95 m x m x m permitted for manual loading according to the German Safety Regulations (UVV) with motor, pneumatic clutch/brake combination, hydraulic overload protection in ram, pneumatic counterbalance in ram, motoric ram adjustment, manual stroke adjustment, motoric centralized lubrication, bolster plate, two-hand operation

Condition: new, Year of construction: 2023, Highly efficient series production Clamp – enter the cutting dimension – start. Automatic saws with loading are a standard of rational series processing of bar and bundle material. Cutting area max. up to 290 x 320 mm. Furnishing Automatic hydraulic sawing machine with NC control for cutting from 0° to 60° right, complying with all CE safety standards The device has 9 programs, each of which composed of 99 individual steps, with a total number Ffodpfxofww Sqj Abusu of approx. 890 cutting positions, with corresponding piece counter Function: material feed closing fixed vice Blade rotation, distribution of emulsifiable liquid, temple lowering until the end of the cut and return of the feed carriage until specified amount bail return and stop the blade rotation by cooling liquid distribution cycle repetition Hydraulic feed cut by cut with no length limit Numerical control of quantity and length of cut Hydraulic control center with cutting pressure adjustment The saw blade is tensioned electro-mechanically by means of Microswitch monitored. Device with brush for belt cleaning Bimetallic strip 3200 x 27 x 0.9 mm Section thickness 1.2 mm Material feed stroke 600 mm Motor hydraulic center 0.75 kW Electric pump 0.09 kW to cool the belt It is always possible for you to inspect the desired system in our production/demonstration hall. Please do not hesitate to contact us.

Condition: excellent (used), Year of construction: 1996, pressure: 13 bar, operating pressure: 13 bar, 1 used steam boiler ----- Make: LOOS, Gunzenhausen Type: U-HD Heating surface approx.: 53 m² Output: 3,200 kg/h Max. operating pressure: 13.00 bar Fsdpfx Aev I Rpaobuofu Increased test pressure: 24.05 bar Water capacity at low water level approx.: 2,650 l Water capacity when full approx.: 3,770 l Year of construction: 1996 Equipped with a Weishaupt gas/oil combi burner, gas control system, control cabinet mounted on the boiler body, feedwater pump, and the existing coarse and fine valves.

Condition: used, functionality: fully functional, operating hours: 4,189 h, fuel type: diesel, mast type: duplex, FORKLIFT TCM FD25Z1 IZUSU ENGINE DIEZEL SHORT MAST.....START AND DRIVE..... Ffsdet U Ivtjpfx Abuou

Year of construction: 2020, condition: excellent (used), 2 cats EK DMR Fodpfx Ajtu Nmdjbujfu

Condition: good (used), Make: OMERA Type: R4 / 12-2 Year: 1976 Table length : 1900 Table width : 1000 Fjdpfx Abokvnumjusfu Steady arm throath HOR : 670 Steady arm throath VER: 940 Stroke cylinder : 350 Column diameter : 200 Specifications Metric US Standard There are no specifications for this machine (yet). Dimensions (Estimate) Length 3000 mm Width 2200 mm Height 2500 mm Weight 2800 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Year of construction: 1986, plate thickness 6,0 mm pressure 18 t cutting angle - upper blade 90 ° blade length 225 x 225 mm voltage 380 V total power requirement 5,5 kW weight of the machine ca. 650 kg dimensions of the machine ca. 1,10 x 0,80 x 1,05 m Ffedpfog Ip Efex Abueu - Angular stops adjustable

Condition: used, Year of construction: 1995, turning diameter over bed slide: 500 mm, Universal lathe Make: ZMM Type 500 Year: 1995 Technical Data Ffsdswudhuepfx Abueu Manufacturer: ZMM Sliven Model: Universal 500 Year of manufacture: 1995 Centre distance: 1000 mm Swing over bed ø: 500 mm Spindle bore: 73 mm Dimensions (L x W x H): 2.7 x 1.2 x 1.8 m Weight approx.: 3100 kg Equipment • 3-jaw chuck Röhm ZS 350 mm • Quick-change toolpost • Live center • Coolant pump • Machine lamp All information subject to change. A live demonstration under power is possible at any time in our showroom.

Condition: used, Year of construction: 1961, ram hammer weight 750 kg ram hammer stroke 660 mm no. of strokes 100 /min impact energy 2040 kJ distance lower die block / ram gudeway 6600 mm Throat 750 mm steel forging - rectangular up to 240 mm steel forging - diameter up to 270 mm power requirement 75,0 kW weight of hammer 16,5 t weight of anvil 15,5 t Ffodpfjvuullex Abuou weight 32,0 t dimensions (WxDxH) 3,2 x 1,45 x 3,45 m Forging hammer as is where is, WITHOUT putting into operation / WITHOUT additional work, free loaded to truck video at seller's site before dismantling available

Condition: good (used), Year of construction: 1963, Vertical lathe JUNGENTHAL Type: DK 1400 built in 1963 with 1 axis digital readout. turning diameter max : 1400 mm face plate : 1250 mm Ffedevi Hryjpfx Abuju Automatic turret head spindle speed : 3,5-180 rpm feeds : 0,063 - 3,15 mm/rev rapid traverse : 1800 mm/min Further data see data sheet Machine documentation available . Dimensions : Length 4 m Width 2,4 m Height 3 m Weight 16t Good general condition .