Vacuum lifter Schmalz VWT 150-180-4 2007

Schmalz VWT 150-180-4

Condition: excellent (used), Year of construction: 2015, I sell the 2-head UV-drying tunnel Superfici Essiccatoio UV Model: Poliedra S.Cure 1650x2 + TT1 3500. Year 2015. Available immediately. Bdodpfeffk Etox Abuei Repairs needed: Display, Energy power units for each two UV-units

Condition: good (used), Clean air extraction system Bsdpfx Aborb D Nsuodi Used machine, in good condition Images to follow mobil Jet 160, Connection 160, Fan 2.2 kW Air flow rate 1850 m³/h, 400 V

Year of construction: 2016, condition: excellent (used), Painting booth Diana serie with horizontal ventilation Modern technology: Dust free operation paint overspray collection system Stable spraying temprature Bdedpfxsygum Re Abuei Control box with safety function Length:16000mm Width:6000mm Height:6000mm

Condition: excellent (used), Year of construction: 2015, functionality: fully functional, machine/vehicle number: C24V5177, type of input current: three-phase, input voltage: 400 V, overall weight: 1,400 kg, Machine in perfect condition, very little used. It turns over the pallet with load and returns empty pallet allowing you to change it easily. For example for changing plastic to wooden pallets for replacing broken pallets with new ones. 2 pcs available, price / pc. You can find manufacturer's video attached but we can also make a recording for you. Pallet changer, pallet turner, pallet inverter. Bsdsvahymepfx Abusdi

Condition: good (used), Year of construction: 1990, type of input current: three-phase, Film wrapping machine + shrink tunnel KUPER DUPLEX 2100/650 + KUPER ST/I-1400 Film wrapping machine Manufacturer: Kuper Type: DUPLEX 2100/650 Year of manufacture: 1995 Film roll width at the top: 2000 mm Film roll width at the bottom: 2000 mm Packaged goods height (passage height): 650 mm Film roll diameter: 400 mm Compressed air: min 5 bar Compressed air consumption (per cycle): approx. 16 L swing arm with chain lift seal bar length 2100 mm "Siemens" control panel overall dimensions: 3000x2000x2300 mm Shrink tunnel: Manufacturer: Kuper ST/I-1400 year of manufacture: ca 1988 max capacity: width: 1350mm height: 650mm work length: 3000mm 2 pcs centrifugal fan blow-off units heating power: 59 kW temperature range 230 °C endless conveyor belt Bodpjkn Rz Hjfx Abuedi throughput speed 5 m/min Length: 3500 mm Width: 2350 mm Height: 1850 mm

Year of construction: 2016, condition: excellent (used), - (dust-free operation, paint overspray collection system, stable spraying temperature, elevated drying temperature) Control box including advanced safety functions and operator-friendly software- (weather condition independent operation, elevated temperature in the drying phase)- (daylight-grade illumination, fire safety, efficient ventilation rendering operator's individual respiratory protection equipment redundant)- Low operation cost : (reduced operating costs owing recirculation of warm air in the drying phase)- (efficient dust collection, low solvent vapor concentration, low air pollutant emission)- Limited operating area requirement : (minimized production area) Length:16000mm Width:6000mm Height:6000mm Bedoygu Smspfx Abusdi

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 5,600 mm, total length: 11,200 mm, total width: 5,100 mm, type of input current: three-phase, warranty duration: 24 months, inner dimension height: 4,970 mm, inner dimension length: 11,000 mm, temperature: 80 °C, inner dimension width: 5,000 mm, air demand: 52,000 m³/h, input voltage: 380 V, heating capacity: 250 kW (339.91 HP), power: 45 kW (61.18 HP), fuel: liquid petroleum gas (LPG), input frequency: 50 Hz, energy consumption: 45 kWh, insulation thickness: 50 mm, nominal power: 250 kW (339.91 HP), sheet thickness steel (max.): 2 mm, Equipment: lighting, * Air Preparation Unit: The air preparation unit is a recirculation system that supplies the cabin with filtered fresh air and exhausts used air during the painting process. It heats the air to 60 °C, mixes the used air with 10% fresh air via an automatic multi-damper system, and reheats the air before routing it back into the cabin. The air is heated using a burner and a heat exchanger, both made of high-quality 304 stainless steel and housed within the fresh air unit. During painting, the air is filtered twice (via front and ceiling filters) before it enters the cabin. The contaminated air is also filtered twice (through inlet and outlet filters) before it exits via the exhaust unit. Air preparation units are insulated like the side walls to minimize heat loss and are protected against potential vibration and noise thanks to rubber seals on the covers. The exhaust air is regulated by a damper in the outlet duct, which helps control the internal pressure of the cabin. * PRINCIPLES OF CABIN OPERATION: The processes in the cabin are controlled via a control panel that manages the following steps: * PAINTING PROCESS: During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled by the extraction unit. Floor filters (paint stops) capture paint particles, and the air passes through the final exhaust filters before being discharged. * FLASH-OFF PROCESS: After painting, the cabin operates for approximately 15 more minutes to purge residual solvents and thinners. During this phase, fresh air from outside continues to circulate in the cabin. * DRYING PROCESS: In this phase, 80% of the air passing through the cabin is heated to 60 °C and supplied to the cabin via a distributor. As 20% of the solvent is released during drying, these solvents are expelled with the exhaust air. Industrial coatings are typically dried at 60 °C, but the cabin temperature can be adjusted via the control panel as required. * COOLING PROCESS: After the 30-minute drying process, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the 5-minute cooling phase, fresh air from outside circulates in the cabin, after which the system stops automatically. Bsdpfx Ajwzl Hxobuodi ELECTRICAL AND ELECTRONIC EQUIPMENT: These control panels manage the functions and operation of all machinery and devices inside the cabin. The control panel is constructed from durable galvanized sheet metal and steel profiles and is fully enclosed to protect against dust and moisture. Electrical devices and control panels: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control lines between the panel and motors or other electrical devices. • Electrical wiring is designed to allow for cabin relocation if necessary. • Operating devices use 380 V 50 Hz, while control devices use 220 V.

Condition: used, Year of construction: 2002, UV dryer, Cefla UV 2000 Bdjdjyifwpjpfx Abuei - Manufacturer Cefla/Sorbini - Type UV 2000 M2 / TN3000 - Year of manufacture 2003 - Working width 1.300 mm (1.445) mm - Working height 900 + - 40 mm - Operating side right - Max. part height 70 mm - Number of tubes from above 2 pcs. - diagonally positioned tubes 2 pcs. - Suitable for mercury tubes - Suitable for gallium tubes - Tube power max. 120 W/cm - with belt transport - Length 3.000 mm - Width 2.300 mm - Height 1.500 mm - Volts, Hz 400 /50 - Total electrical connection 86 A / 36.4 kW - Voltage fluctuations max. +/- 5%

Condition: new, Year of construction: 2025, Sidesleever for thick PE films, that can do full wrapping of the product. All 4 sides are properly sealed. XL version for large products, inclusive suitable shrink tunnel. Suitable for dust protection and transport purposes. Low cost packaging solution even for large products of up to W+H Bdjdpfx Aev Nl Rnobuji

Condition: excellent (used), Machine suitable for the polishing and the cleaning process (top & bottom) of panels. - Upper cleaning system (with 2 motorized rubbered cross belts with brushes) Motor power: Kw 0.19 Bdodpfx Absyw Rpqeuji - Lower cleaning system (with 2 motorized rubbered cross belts with brushes) Motor power: Kw 0.19 - Max working width mm 1500 ca.