Drilling machine

SCM Cyflex F900

Condition: used, Year of construction: 2011, Base Machine M800 X5 TV 1 WORKING RANGE X: 5,020 mm Y: 1,830 mm Z: 675 mm Clearance Height: 300 mm (from 50 mm suction cup height) MACHINE STRUCTURE The base structure is a monolithic construction made from thick-walled steel. It is reinforced across the entire machine bed with welded components, providing exceptional stability. The table design, with its large base, is the key to ensuring lasting precision and stability. The machine’s layout enables the operator to achieve optimal workflow with minimal space requirements. The mobile gantry is built as a solid monoblock. It is positioned in the X direction on prismatic, ground guides with recirculating ball carriages. The machining unit is mounted on this mobile support carriage, also on prismatic, ground guides and recirculating ball carriages. AXIS MOVEMENT All axes travel on prismatic linear guides with large cross-section and recirculating ball shoes with a wide contact surface, which ensures optimal sliding, even at high speeds and accelerations. The precise and fast positioning of the movable gantry (X-axis) is achieved via helical rack and pinion. Large cross-section recirculating ball screws ensure accurate positioning of the machining unit along the movable gantry (Y and Z axes). The perfect mechanical dynamics and maximum positioning accuracy are controlled by high-quality drives and brushless motors. Max. axis speeds: · X-axis = 90 m/min · Y-axis = 90 m/min · Z-axis = 30 m/min Safety device with bumper and light barrier 1 Bumpers with sensors are fitted to the movable upright, and a light barrier system is installed at the front of the machine. If the operator enters the active zone, the X-axis travel speed is reduced to a lower value of 25 m/min without stopping the machine. This system allows parts to be loaded during pendulum operation without the limitation of access areas, as seen with pressure mat systems. This prevents unwanted interruptions in the machining cycle and offers greater freedom of movement around the worktable. CE certification for the safety system 1 Safety protection fence 1 Side and rear protection fence Automatic central lubrication controlled via CNC 1 The lubrication of the X, Y, and Z axes is controlled by the CNC; intervals are regulated automatically, without manual intervention. Central extraction connector 1 All individual extraction connections of the machining units are collected into a central extraction port. Inside the port, there are various slider valves controlled by the NC. This reduces the required extraction air volume. Chip conveyor 1 Maxi – 5-axis electrospindle 11 kW HSK-63 “Prisma K 1 5-axis electrospindle, 11 kW at 20,000 rpm S1 (100% duty cycle) Speed: max. 20,000 rpm Rotation direction: left/right Liquid cooling Tool interface HSK 63F Inverter 18 kW, stepless, smooth power delivery Max. rotation B-axis = 200° (+-100°) C-axis = 650° Thanks to the non-orthogonal axes, it is possible to perform complex horizontal positioning in a small workspace. This enables the machining of complex geometries without the risk of collision. Itodpfxjxy Tmnj Ab Seg

Condition: new, Year of construction: 2024, functionality: fully functional, overall weight: 1,060 kg, total height: 1,800 mm, total width: 1,830 mm, total length: 2,000 mm, feed length X-axis: 3,000 mm, feed length Y-axis: 800 mm, feed length Z-axis: 50 mm, spindle speed (max.): 3,200 rpm, workpiece weight (max.): 25 kg, power: 2.2 kW (2.99 HP), air demand: 750 m³/h, operating pressure: 6 bar, number of spindles: 12, empty load weight: 975 kg, warranty duration: 12 months, Easy programmamble through-feed boring machine with touch-easy-smart software, 3 controlled axis X,Y,Z, also performing grooving operations (optional) and working from above Vacuum panel feeding Machine manufactured according to EC standards STANDARD EQUIPMENT HEAD UNIT Independent spindles N.7 vertical Iedpfeu U Hgiex Ab Sstg N.1 double horizontal -spindle TH1 (X axis) for back/ forth drilling Manual SIDE-ALIGNER PANEL EDGE-READER for perfect panel joints Teleservice Software Dust-collection nozzle Wokring table with GENTLE BRUSHES to avoid storage of dust and shavings. Working process can be in a cycle or back to the operator HARDWARE & SOFTWARE 12" touch-screen - NO TEXT System, patented by Maggi USB and Ethernet ports for file uploading, on-line assistance and system upgrades System based on Linux Kernel Up to 1.000 working programs storable Package: on a wooden pallet (2200x2050x160 mm - Kg 123)

Condition: new, Year of construction: 2025, functionality: fully functional, warranty duration: 12 months, Our state-of-the-art VFFS packaging machine is a true all-rounder, specifically designed to optimally support companies that demand the highest quality standards. With exceptional build quality and a wide range of applications, our machine features intuitive operation that streamlines your packaging processes. The highly powerful motors and user-friendly color touchscreen control system provide maximum flexibility during format changes and significantly simplify your packaging operations. The machine is equipped with memory slots for storing machine parameter settings. For this packaging line, we also offer fully and semi-automatic infeed systems, including weighing solutions, which can be retrofitted according to your requirements. If you want to optimize your packaging processes with robust productivity and high quality, Impuls Packaging is your ideal partner. Machine features: 1. Single film unwind 2. Individually servo-driven sealing jaw 3. Three servo drive controllers 4. HMI control panel 5. Two independent temperature controllers 6. Housing made of stainless steel 304 7. Documentation in the local language 8. Registration mark control 9. Programmable bag length 10. Vertical product flow 11. One format set is included in the price. Technical parameters: Iodpfx Abewlgnro Sotg 1. Product length: L50-290mm 2. Product width: W80-200mm 3. Packaging speed: up to 45 products/min (depending on product, bag length, and material) 4. Maximum film width: 420mm 5. Power supply: 1Ph. 220V 50Hz 6. Total power: approx. 3.9 kW 7. Machine weight: approx. 300 kg 8. Machine dimensions: approx. 1300x1170x1585mm Bag types: 1. Classic flow pack bag 2. Stand-up pouch (classic flow pack bag with side gusset – available as an optional extra)

Condition: good (used), Traypacker / wrap arround packer Trays and wrap-around boxes minimum packaging size L x W x H = 190 x 140 x 80 mm maximum packaging size L x W x H = 460 x 350 x 250 mm Itsdpfefxypisx Ab Sjg 4 lane machine Hotmelt machine was rebuild in 2018 siemens s7 plc controlled easy format change as-is or adjusted to customer needs

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors. Itjdpfx Absvf E Ave Sog

Year of construction: 2002, condition: good (used), Make: Matsuura Type: LX-O Control: YASNAC Year: 2002 Specifications Metric US Standard X - Travel 330 mm Y - Travel 300 mm Z - Travel 250 mm Table Length 540 mm Table Width 320 mm Itedpfolz Rvljx Ab Sog Table load 100 Feed rate X-Axis 90000 mm/min. Feed rate Y-Axis 90000 mm/min. Feed rate Z-Axis 90000 mm/min. Spindle Taper 30 ISO/Bt/Mk Power on spindle 7.5 kW Speeds / ranges 40000 Rpm ATC / revolver 30 Chip conveyor Yes Dimensions (Estimate) Length 2800 mm Width 2600 mm Height 28000 mm Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, functionality: fully functional, In this offer you purchase a used colour production system ‘Canon imagePRESS C9010 VP’ Iodpsu Ecl Eofx Ab Sstg Object of sale: 1 x Canon imagePRESS C9010 VP with the following equipment: incl. Prisma Controller or Fiery incl. booklet finisher N2 incl. High Capacity Stacker H-1 incl. POD Deck D1 Counter readings: Total: Approx. 1,880,920 pages Condition: This offer is a used device, which may show signs of use (minor scratches or yellowing). (minor scratches or yellowing). The device has been tested for function A test printout can be seen in the photo Packaging and dispatch: You are welcome to view the device during our business hours. Please make an appointment for this! Seaworthy packaging and worldwide shipping available on request! A function test will be recorded on video for you before dispatch or collection. For further information you can of course also contact us personally.

Condition: good (used), Year of construction: 2023, operating hours: 50 h, Brand Ferromatik Milacron GmbH Type eQ-280 - 2290 Year of manufacture 2023 Machine hours 50 hours Clamping force 2,800 kN Screw diameter 60 mm Itsdew Ebpwspfx Ab Seg Injection pressure 2,238 bar Maximum shot volume 905 cm³ Max. distance between tie bars 710 x 660 mm Min. mould height 250 mm Distance between plates max. 1,400 mm Dimensions (LxWxH) 8,500 x 2,100 x 2,500 mm Weight 18,400 kg

Year of construction: 2010, condition: excellent (used), functionality: fully functional, Manufacturer: CFS (GEA) Type: Compact 420 Year: 2010 Itodpertq I Esfx Ab Sog Electrical connection: 28 kW, 42 A, 400 V, 50 Hz Labelling machine: Manufacturer: CFS Type: TiroLabe TL-150 Year: 2010 with gas flushing including 4 format sets Condition: very good The metal detector and Espera conveyor visible in the picture are not part of this offer. They are separate machines.

Condition: new, Year of construction: 2022, functionality: fully functional, TAKAMAZ CNC Compact loader FC60 Lathe with automatic loader unloader quickest loading system in the world loading time new part 2,8 sec. loading cap. till 60 mm diameter. loading lenght max 50 mm max weight 1 kg per side loading feed 120 m min include part turning for loading Fanuc Control full warranty 2 year Lathe spec. Spindle motor 7,5/5,5 kw turning diameter max 180 mm turning lenght 240 mm bar cap. 35 mm collet chuck 173E Itodpfjm E I D Hex Ab Sjg till 40 mm diameter spindle nose A2-5 spindle speed 4500 rpm tool pos 8 stations tool shank 20x20 mm boring holder 25 mm diameter rapid speed X/Z 18/24 meter machine dimension 1,36 x 1,37 meter height 1,7 meter weight 2,7 ton total power 14 KVA Price is EXW (Stock Europe), Include loaded on truck. Transport, installation, commissioning, training, and yearly service contracts are available upon request for an additional fee. Installation and training is always done by our high qualified Service team in 3 locations in Europe. Netherlands, Germany, Romania.