3D Portal Coordinate Measuring Machine

Zeiss ACCURA (X1.600 , Y 2.400, Z 1.000 mm)

Year of construction: 2022, condition: as good as new (ex-display), Manipulator with hydraulic height adjustment, face plate with clamping slots and manual remote control. Height (face plate horizontal): approx. 532 - 1.132mm Lifting distance/lifting time (hydraulic): approx. s = 600mm, t = 20s Swivel range of face plate: approx. +-300°. Height (Pl.-sch.vertical axis): approx. 709mm Dimensions face plate: Ø1.200mm x 40mm, 6x clamping slots Speed of the main axle: approx. 2.0 rpm (other Iaedpfx Aaofw Ah Rjden Torque main axis of rotation: approx. 7,500 Nm Face plate speed: approx. 2.5 rpm Face plate torque: approx. 1,500 Nm

Condition: new, 900 mm 900 mm 900x900 mm saw band length 9300 x 67 x 1,1 mm table height 790 mm band speed 14 - 60 m/min total power requirement 11 kW weight of the machine ca. 8,45 t dimensions 4,485 x 1,68 x 3,15 m The semi-automatic, hydraulic saws from the X-tech line offer the best Saw technology and best performance when cutting special steels • The electro-welded machine frame and the steel saw frame meet requirements all cutting needs and eliminate vibration and noise. • The chip conveyor is hydraulically driven and the speed is adjustable • All movements of the machine (saw frame, vice, feed, Saw band guides) are carried out thanks to modern linear guides with high static and dynamic load performance, which also has very low sliding friction to guarantee. • Another characteristic feature is the roles for the Positioning of the material by a hydraulic motor are driven. They move at right angles to the material, and thus allowing optimal clamping of the material. • Thanks to the height control of the saw band position, the operator can place the band in place near the top edge of the material. After the cut is finished, the tape automatically raised back to the previous position. Alternatively you can also “Remain” can be selected in the lower position. During the The software compares the cutting load with the cutting cycle Default. This means that the sawing system can be stopped in the event of irregularities become. • The saw band is cleaned by two adjustable steel brushes. The drive takes place hydraulically. • The hydraulic unit including filter and pressure gauge guarantees one particularly quiet operation at constant pressure. • Finely ground carbide inserts that clamp the saw blade, complete with lateral, hardened and adjustable guide rollers. The adjustable one The tape guide automatically moves as close as possible to the material. Iodpfx Aaofg E Hpodsan • The saw band is tensioned via a hydraulic cylinder, which is carried out by the Machine software is controlled. The voltage is set according to a given Time automatically delimbed when the machine is idle or after a cycle has been carried out. • Automatic version with CNC control in the X-TECH 900 / 1200 models a feed length of 500 mm for the series for high production rates. • The material is carried by a table with seven rollers. These will driven by a hydraulic orbital motor through which the material can be placed precisely even under maximum load. • All guided movements are carried out by four recirculating ball guides with one high capacity for static and dynamic loading; strong reduced feed friction. Tempered and ground prismatic Guides. Price on request.

Year of construction: 2006, condition: excellent (used), 70 rm pallet rack SSI Schaefer Palflex incl. insertion grid second hand, good condition, see pictures year of construction 2006 height 4 m depth 120 cm field load 12000 kg frame galvanized Beam red Inlay grid included! 2 pcs. grids per 2,7 meter beam length Negotiable price: € 6.950,-- net ex stock Offer consists of: + 26 pcs. frames pre-assembled, depth 120 cm, height approx. 4 m +100 pcs. beams, length 2,7 m, 1500 kg payload/shelf with evenly distributed load +200 pcs. suspension guards +100 pcs. galvanized insertion grids for 50 levels of 2.7 m beam length each +104 pcs. concrete anchors Load plates Iaodpfjkx E I Nex Aadon Goods are in stock. Transport and assembly possible on request. Inspection possible at any time by arrangement. More info on request. Constantly over 5000 running meters of pallet racks from numerous manufacturers in stock. (Changes and errors in the technical data, specifications and prices and prices as well as prior sale reserved! See our terms and conditions, all prices excl. VAT ex stock) Purchase / Sale We are constantly looking for, or offer numerous items from various areas broom-clean business clearances company liquidations Fast- flexible - ready to hit! We also clear and dispose for liquidators. Write us with some keywords, we will contact you immediately. To get to our site, please click on our logo!

Condition: new, capacity 90 degrees: round 350 mm capacity 90 degrees: square 330 mm 500 x 310 band speed 15 - 100 m/min table height 844 mm dimensions of saw-band 4250 x 34 x 1,1 mm total power requirement 2,2 kW weight of the machine ca. 1,2 t dimensions of the machine ca. 1,4 x 2,4 x 1,935 m ACTION PRICE!!! 2-column double miter band saw K-tech DG 50/33 HA-I • 2-column miter saw • Solid, yet easy to use • Material height sensor (automatic cut start detection) • Smooth running thanks to bevel cut, feed controller + cutting pressure controller • Massive material infeed roller • Removable chip tray (disinfection) • Energy-saving and low-vibration thanks to bevel cut Iasdefg E Hlspfx Aaden • Ergonomic, safe and free-standing control panel • Frequency-controlled saw drive 15 -100 m/min. • Hydraulic cutting pressure control valve • Hydraulic control of saw frame and vice • LEDs for monitoring all safety functions • Large dimensioned wheels (520 mm) a. • Clear miter setting up to 60° Semi-automatic function: 1. Clamp material 2. Saw starts 3. Rapid lowering to the start of the material or the same for series cutting cut 4. Saw band off 5. Raise the frame to just above the material 6. Open the vise

Condition: excellent (used), Year of construction: 2003, functionality: fully functional, measuring range X-axis: 900 mm, measuring range Y-axis: 1,200 mm, measuring range Z-axis: 700 mm, Zeiss Prismo VAST XT Year of manufacture: 2003 Retrofit Measuring range: X = 900 mm, Y = 1200 mm, Z = 700 mm C99 controller with operating panel VAST XT probe head VAST GOLD probe head (optional) 13-position probe changer magazine Probe change rack Probe accessories Iajdpfx Ajwyukdoaden Calibration sphere Technical documentation Additional accessories HP workstation with monitor Calypso Basic software Further options available on request Available at short notice Delivery without the automatic feed unit shown

Condition: refurbished (used), Year of construction: 2025, functionality: fully functional, machine/vehicle number: 1845/455, Completely refurbished: Mechanics, geometry, hydraulics, and electrical components Wheelhead Disassembly, cleaning of parts, replacement of worn and defective components, motor overhaul, replacement of bearings, replacement of belts, spindle disassembly, replacement of seals and O-rings, plus adjustment. New paintwork. Workhead Disassembly, cleaning of parts, replacement of worn and defective components, motor replacement, replacement of belts. New spindle bearings. New paintwork. Tailstock Disassembly, cleaning of parts, replacement of worn and defective components, motor replacement, replacement of belts. New spindle bearings. New paintwork. Internal grinding attachment Disassembly, cleaning of parts, replacement of worn and defective components, installation of the support and geometry alignment. New paintwork. Hydraulics Disassembly, motor replacement, hose replacement, defective and worn parts replaced. Hydraulic block checked. X-Axis Disassembly, replacement of worn items such as O-rings, seals, rings, etc., overhaul of hydraulic piston, regrinding of tables. Z-Axis Disassembly, regrinding of tables, replacement of worn and defective parts, overhaul of hydraulic piston, scraping of V and flat guides. New paintwork. Measuring system Digital 2-axis display included. Electrical cabinet Replacement of motor contactors and relay controls. New wiring. New variable speed drive (frequency inverter) for the workhead. TECHNICAL SPECIFICATIONS Distance between centers: 1500 mm Distance between centers (workhead to tailstock overhang): 1650 mm Center height, standard: 125 mm Center height with riser blocks: 225/250 mm Maximum grinding diameter: Ø 250 mm Maximum grinding diameter with riser blocks: 450/500 mm Table Usable surface: 2060 x 140 mm Max. length and width for surface grinding: 1750 x 200 mm Longitudinal travel, manual or hydraulic: 1750 mm Manual table movement, 1 handwheel revolution – coarse: 20.006 mm Manual table movement, 1 handwheel revolution – fine: 2.457 mm Table speed, continuously via hydraulics: up to 6 m/min Iedpfx Aajxt Ilfsdean Table swivelling: 6° Stop and return: 0–5 sec. Workspindle Workpiece speeds, continuously variable (electric): 20–400 rpm Swivelling: 360° Workspindle taper (internal): MT5 Tailstock Internal taper, tailstock spindle: MT3 Spindle retraction, manual or hydraulic: 30 mm Diamond dresser taper (internal): MT0 Universal grinding head Cross slide travel for wheel: 285 mm Rapid traverse for wheel slide, front and rear: 40 mm Grinding spindle speeds: 1500 – 1700 – 2200 – 3600 rpm Vertical grinding spindle movement, center heights: 125–330 mm Max. wheel for cylindrical grinding: 400 x 50 x 127 mm Max. wheel for surface grinding: 250 x 20 x 76 mm Head swivelling with locking at every 90°: 270° Wheel feed 1 division of the micrometer drum: 0.005 mm/Ø Automatic wheel feed, max.: 0.9 mm/Ø Motors Grinding spindle motor: 2,900 rpm / 4.0 hp Workspindle motor: 3,000 rpm / 2.0 hp Coolant pump motor: 2,850 rpm / 0.12 hp Internal grinding attachment Bore: 70 mm Internal grinding spindle speed Ø70 mm: 14,000 rpm Internal grinding spindle speed Ø50 mm: 21,000 rpm Subject to error or omission, the technical information is provided without obligation.

Condition: excellent (used), Year of construction: 2018, operating hours: 21,000 h, functionality: fully functional, machine/vehicle number: S4E184001, turning diameter over cross slide: 430 mm, turning length: 670 mm, turning diameter: 220 mm, spindle bore: 45 mm, spindle speed (max.): 6,300 rpm, overall weight: 4,300 kg, Used CNC hard turning lathe with counter spindle Manufacturer: EMCO Iajdpfx Asw Rrvwoadon Model: Emcoturn 45E Year of manufacture: 2018 Few operating hours Control: Siemens 828D Number of tools: 12 driven units Max. speed: 0-6000 rpm

Condition: used, Tool presetter EZSET EZ400 Isdeuhb Stepfx Aadsan

Condition: used, _____ Description: Year of manuf. : 2020 Control : Sonstige WEISS CNC Centre width : 6 mm In Generel: ear of construction:2020 Control system:WEISS CNC Centre width:6 mm Centre height:200 mm Grinding wheel dimensions:400x60 mm + 0x60 mm Workpiece headstock: Speed:1 rpm Workpiece weight max.:25 kg Sanding diameter max.:390 mm Mounting:MK4 Grinding headstock: Peripheral speed:2 m/s Grinding disc dimensions right:0 x 60 mm Grinding disc dimensions left:400 x 60 mm X-axis:380 mm Z-axis:1,1 mm B-axis:torque motor, infinitely variable Tailstock: Pinole diameter: mm Pionole stroke:45 mm Iaedpfx Aasv Armcedon Mounting:MK 4 Cylinder fine adjustment:+/- 0.04 mm Equipment: Positioning sensors:Direct scales Grinding spindles:2x grinding spindle (left/right) GAP / Crash Controll:Structure-borne sound (Sensotronik) Balancing:MPM balancing device Workpiece measurement:Marposs PF ME Automation:Robot interface prepared Set-up mode:Electronic handwheel Emulsion mist separator:Mechanical Dresser:For external grinding wheel left/right Accessories:Various grinding discs + flanges

Condition: used, Year of construction: 2001, Cutting width: 3300 mm Cutting length: 3350 mm Weight: approx. 4000 kg Saw blade projection: 100-(115) mm Saw carriage: Feed speed: 100-(130) m/min. Return speed: 100-(130) m/min. Main saw blade: 400-(430) mm Motor: 7.5-(11-13.2) kW Scoring unit: 215 mm Motor: 2.2 kW Pusher: Rapid feed: 160 m/min. Return speed: 60 m/min. Extraction: Air speed: 30-35 m/sec. Extraction nozzle: 200 mm / 115 mm Compressed air: Pressure: 5-6 bar Consumption: 20-30 l/min. Iedpfevvkqgox Aadoan Storage location: Nattheim