Condition: used, Year of construction: 2016, Makino A51NX in very good condition, including a new ATC tool changer and Cubes. Approx. 11,000 hours of cutting time. Capacity & Travels: Pallet Size: 400 × 400 mm X-Axis Travel: 560 mm Y & Z-Axis Travel: 640 mm Max. Workpiece: ∅ 630 mm × 900 mm Dwjdpszg N E Hefx Aggeb Max. Payload Capacity: 400 kg Spindle: Spindle Speed: 15,000 RPM Spindle Taper: HSK-A63 Motion & Feed Rates: Rapid Traverse Rate: 60,000 mm/min (1,968 ipm) Cutting Feedrate: 50,000 mm/min Axis Acceleration: 1G B-Axis Indexing: Full 4th axis, Direct Drive (0.001-degree increments) Tooling: ATC (Automatic Tool Changer) Capacity: 60 tools Tool-to-Tool Time: 0.9 seconds Max. Tool Diameter / Weight: 170 mm / 12 kg 04003 HSK-A63 Spindle – Replaces the standard ISO50 interface. Features a double taper, full face contact, and hollow shank interface. Tool clamping force is higher than 44kN; HSK tool holders are required. 14017 HSK holders for 60 Tool ATC 26001 Moire Scale Feedback X, Y, Z-Axis Increments 0.05µm, positioning tolerance Tp = 0.006mm (ISO 230-2). 29006 Through Spindle Coolant 3.0MPa – Provides TSC flow of 30 l/min at 3.0MPa, replacing the standard 1.5MPa. Air through the spindle is possible. The pressure data refers to the output flange of the pump. 29009 Flow Switch for Through Spindle Coolant – Monitors through-spindle coolant flow. The machine will feed hold if the flow is below a preset level. Note: Recommended option for filtration systems to prevent tool damage. 31002 Air curtain for splash guard window – Located in the middle of the operator-side window, this air curtain prevents chips and coolant from obstructing the view. 37000 Broken tool sensor outside machining area (BTS) – Tool breakage detection for centric tools (tool diameter 1-40mm, tool length 65 - 430mm). Length measurement is performed using a movable probe. The measurement takes place in the ready position for a tool change, outside the machining area. Accuracy ± 2mm. If there is a difference between the measurement before and after machining, an alarm is triggered automatically. 37101L Automatic Workpiece Measuring Device (RENISHAW OMP60) – Three-coordinate measuring probe from RENISHAW with automatic coordinate correction. The signal is transmitted via infrared. Tolerance approx. 0.005mm. 14 automatic measurement cycles are available as pre-programmed cycles in the program memory. Note: requires 13m. Control Options: 60001 Automatic Corner Override (G62) – Automatically decelerates the cutter at a corner depending on the corner angle, in order to maintain the cutting rate per unit time. 62007 Run hour and parts quantity display. 63034 DATA CENTER Storage Type B (total: 800MB) – Communication card with internal 800MB removable flash RAM card used for storing and executing NC data (of subprograms) for high-speed, high-definition finishing and supporting SGI capabilities. CNC programs can be transferred to and from a CAD/CAM system from the operator's pendant by FTP get and put commands over an Ethernet cable. 66003 Additional 48 Work Offsets (G54.1 P1-P48) – Allows for 48 work coordinate systems, simplifying multiple part fixtures. 68010 600 Macro Common Variables – Variable numbers 100-199 are reset and cleared when the power is turned off, while 500-999 are permanent. Pallet Size: 400 × 400 mm X-Axis Travel: 560 mm Y & Z-Axis Travel: 640 mm Max. Payload Capacity: 400 kg Spindle Speed: 15,000 RPM Spindle Taper: HSK-A63 Rapid Traverse Rate: 60,000 mm/min (1,968 ipm) Cut...

Condition: used, Year of construction: 2010, machine/vehicle number: IntNr231656, HAAS DT-1 CNC machining center – manufactured in 2010 For sale is a HAAS DT-1 CNC machining center, manufactured in 2010, equipped with a 3+2-axis system, a Renishaw measuring probe, and a KUKA KR 5 sixx R850 WP. Dsdezwk Iwspfx Aggewb Technical data Manufacturer: Haas Model: DT-1 Year of manufacture: 2010 Machining: 3+2-axis Cycle time: 4,962 h Feed time: 3,079 h CNC control: Haas Chip conveyor: Integrated screw conveyor system Measuring probe: Renishaw Internal cooling (IKZ): present, currently defective Automation – KUKA KR 5 sixx R850 WP, control panel currently defective Dimensions of the robot cell Height: approx. 2,100 mm Width: approx. 1,150 mm Depth: approx. 800 mm Dimensions including infeed and outfeed Height: approx. 2,100 mm Width: approx. 1,150 mm Depth: approx. 2,400 mm The machine can be inspected on-site by appointment. Subject to changes and errors in the technical data and information, as well as prior sale!

Condition: like new (used), Year of construction: 2008, travel distance X-axis: 1,050 mm, travel distance Y-axis: 800 mm, travel distance Z-axis: 880 mm, controller model: Fanuc Oi-MC, KAFO HMC 630 HMC Category: HORIZONTAL MACHINING CENTERS (HMC) Reference No.: 400234 Capacity: 630 X 630 MM Year of Construction: 2008 Technical Specification: SPINDLE Spindle Taper : CAT 50 WORKING CAPACITY Pallet Size : 630 x 630 mm Travels (XYZ) : X1050 x Y800 x Z880 mm B-Axis : 0.001° Distance from spindle nose to table center : 150 - 1030 mm Distance from spindle center to pallet surface : 100 - 900 mm Table Load Capacity : 1200 kg Max. Work Size : Ø1050 mm ATC Dodpfx Ajy D E Sysggowb Tool Change Capacity : 40 Maximum Tool Weight : 20 Kg CNC Control : Fanuc Oi-MC

Condition: used, Year of construction: 2003, functionality: fully functional, HORIZONTAL MACHINING CENTER "FAMUP" MOD. MF 650 CNC FANUC SPINDLE HSK 63 15,000 RPM TRAVELS MM 700X660X550 PALLET MM 500X500 FULL ROTARY TABLE ATC 50 POSITIONS HIGH-PRESSURE COOLANT CHIP CONVEYOR YEAR 2003 Dodpjxwccmofx Aggewb

Condition: used, Year of construction: 2016, functionality: fully functional, machine/vehicle number: 2460067, Technical specifications: # Machining Workspace: X 300 mm; Y 500 (725) mm; Z 375 mm # Axis Description: 3 LINEAR AXES (X, Y, Z) + 1 Rotational Table Axis (A-axis) with Indexing Head, featuring direct angular measurement system, max rotational speed 50 rpm, accuracy +/- 5" # Maximum Clamping/Workpiece Dimensions: Ø 575 x 830 mm; maximum weight 360 kg # Rapid Traverse Speed: X/Y/Z 65/75/75 m/min; Positioning Accuracy Tp: 0.008 mm # Distance Between Spindles: 300 mm # Spindle Speed: 1–17,500 rpm # Spindle Taper: DIN 69893-HSK-A63 (with internal cooling) # Automatic Tool Changer: 2 x 32 tools; chip-to-chip average 2.5 s # Maximum Tool Ø: 75 mm / Maximum Tool Length: 275 mm / Maximum Tool Weight: 7.5 kg Electrical connection: # Voltage: 3x400V / 50Hz # Installed Power: approx. 85 kVA / 125A Dimensions: # Installation Footprint: approx. 3.6 x 6 x 3.7 m # Weight: approx. 10,500 kg Equipment includes: # CNC Control: Siemens 840D SL # Linear Axis Measuring Device: Heidenhain Linear Scales # Chip Conveyor: Knoll Type 550 K-1 # Oil Cooling System # Oil Filtration System, max. 80 bar: Knoll VRF 450_2350 # Shaft, Guideway, and Switchboard Cooling System # 2 Oil Lubrication Systems Dodpjxxtdwofx Aggowb # Oil Vapor Absorption/Recovery System: IFS Vario E2000 (2,000 m3/h) # Fire Protection: Kraft & Bauer # Workpiece Presence Sensing: Low-pressure air detectors # In-process Control: Marposs T25 # Tool Breakage Detection and Length Measurement System: BRK, inductive sensor # Tool Presence Detection in Spindle Machine condition: Fully operational

Condition: ready for operation (used), Year of construction: 2006, travel distance X-axis: 600 mm, travel distance Y-axis: 660 mm, travel distance Z-axis: 660 mm, spindle speed (max.): 12,000 rpm, spindle motor power: 22,000 W, number of axes: 4, This 4-axis Matsuura H. Plus 405 was manufactured in 2006. It features an X-axis travel of 600 mm, Y-axis travel of 660 mm, and Z-axis travel of 660 mm, along with a 360° rotary B-axis. The machine has a maximum workpiece size of 700 × 850 mm and a tool changer capacity of 60 tools. If you are looking to get high-quality machining capabilities, consider the Matsuura H. Plus 405 horizontal machining centre we have for sale. Contact us for further details. • B-Axis: 360° rotary table • Rapid Traverse X/Y/Z: Up to 60 m/min • Pallet Size: 500 × 500 mm • Maximum Workpiece Size: 700 × 850 mm • Maximum Workpiece Weight: 400 kg • Pallet Changer: 2-position • Main Spindle Speed: Max. 12,000 rpm • Tool Holder Options: SK40 / BT40 / HSK63 • Max Spindle Drive Power: 15 / 22 kW Dedpfozwp S Uex Aggswb • Maximum Spindle Torque: 187 Nm • Tool Changer Capacity: 60 tools • Chip-to-Chip Time: Approx. 3.5 sec. Technical Specification Taper Size SK 40

Condition: used, Year of construction: 2007, Multipallet Horizontal CNC Center Doosan HC500, year 2007. 7-pallet pallet system Fanuc 21i-MB control Spindle speed 8000 rpm ISO40 (BT) taper -X850mm -Y700mm -Z750mm 1-degree pallet indexing Djdeycvpfopfx Aggjwb 60 tools Chip conveyor Through-spindle coolant (IKZ) Machine fully operational, available for inspection in France, 01360 Loyettes.

Condition: good (used), Year of construction: 2012, Ref. -No.: 10558 Manufacturer: YOU JI Type: HMC 1200 BP Year of construction: 2012 Type of control: CNC-Steuerung Control: FANUC Series 18i-MB Storage location: Halberstadt Country of origin: Taiwan X-Travel: 1800 mm Y-Travel: 1500 mm Z-Travel: 1360 + 990 mm B-Axis: 360 ° W-Axis: 700 mm Table Dimensions (Lengthxwidth): 1200 x 1400 mm Table Load: 5.000 kg Max. Tool Weight: 25 kg Max. Tool Length: 400 mm Max. Tool Diameter: 125 mm Dedjxxpbxepfx Aggswb Spindle Speed: 30 - 3.500 RPM Numbers Of Pallets: 2 Further information: 4-axis simultaneous machining IKZ (internal spindle cooling) AKZ (external spindle cooling) Synchronized walking (rigid thread cutting) Renishaw RMP60 workpiece probe (radio) Number of pallet changers for automatic pallet change: 2 Size: 1200 x 1400 mm Tool magazine, number of tools: 60 The machine is currently in production and can be viewed by appointment.

Condition: good (used), Year of construction: 2003, Machining center Manufacturer: Matsuura Type: H Plus 405 PC6 Year of manufacture: 2003 CNC control: Fanuc G-Tech 16i Dwedpfxjltlx No Aggob Travel ranges: X/Y/Z: 600 x 600 x 600 mm Table size: 500 x 500 mm 6-position pallet changer Tool magazine: 120 positions 4th axis Knoll high-pressure system Internal cooling: 70 bar 9926

Condition: like new (used), Year of construction: 1987, Used Giddings and Lewis Model MC 50 Twin Pallet Horizontal Machining Centre with Live Spindle, 60 ATC and G&L 8000A Control System. Serial # 445-1052.Year of Manufacture: 1987 Machine Formerly Installed at Rolls Royce Plc In Derby UK. Immediately for Sale and now Located in Belgium where it can be Inspected. Spindle Diameter - 130 MM Spindle Taper - 50 ISO Spindle Travel (Z Axis) - 915 MM Spindle Speeds (4 Ranges) - 5 to 1500 RPM Main Motor - 30 HP Pallet Size - 1219 x 1245 MM Pallet Rotation Increments - 0.001 DEG (360,000 POSITIONS) Pallet Changer Max Load - 5000KGS Pallet Max Load Without APC - 9000 KGS Longitudinal Travel (W) - 1700 MM Vertical Travel Of Head (Y) - 1500 MM Cross Travel (X) - 1800 MM Feed Rates Per Minute - 1.00MM/MIN TO RAPID RATE Rapid Traverse Rate Per Minute (X And Y) - 4500 MM / MIN Rapid Traverse Rate Per Minute (Z And W) - 3000 MM / MIN Auto Tool Changer - 60 POSITIONS Electrical Supply - 415V, 3PH, 50HZ FEATURES AND EQUIPMENT High Pressure (25 Bar) Through Spindle Coolant, High Tolerance Machine. Accurate Machine which was well Maintained and Regularly Calibrated by Manufacturer. Renishaw Probing. Dwsdpju Dahnsfx Aggjb Length - 11679 MM Width - 6502 MM Height - 4423 MM Weight - 40329 KGS

Condition: repair required (used), Year of construction: 1995, machine/vehicle number: VM40067E, travel distance X-axis: 560 mm, travel distance Y-axis: 410 mm, travel distance Z-axis: 410 mm, overall weight: 6,000 kg, spindle speed (min.): 8,000 rpm, Brand / Manufacturer: HITACHI Model: SEIKI VM 40 II Year: 1995 Taper: BT40 Serial number: VM40067E Control unit: SEICOS MY II DIMENSIONS Table dimensions: 760 x 400 mm. TRAVEL X-axis traverse: 560 mm. Y-axis traverse: 410 mm. Z-axis traverse: 410 mm. SPINDLE Spindle speed: 8,000 rpm. Spindle power: 5.5 / 7.5 kW. WEIGHT AND DIMENSIONS Machine weight: 6,000 Kg. Dedozl S I Uepfx Aggewb ACCESSORIES 30-station automatic tool changer / ATC Capacity: 30 Tools Nikken 4th axis CNC rotary table (REQUIRES REPAIR) The machine is complete and includes documentation and manuals. The mechanical part is in good condition. The electronics need repair; likely the power supply. (NEEDS TO BE REPAIRED) The machine is complete. It also has documentation and manuals. The mechanical part is good. The electronics need repair. Probably the power supply.

Condition: used, Year of construction: 2020, x-travel 810 mm y-travel 610 mm z-travel 640 mm Dwjdpfszbmzvex Aggob b-axis 360 ° Control Ultimax spindle tunring speed 8.000 U/min power capacity 56 kW tool taper SK 50 rapid traverse 45/40/45 m/min auto power on hours ca. 13.674 h spindle hours ca. 4.211 h In our assessment, the machine is in good used condition and can be inspected under power by appointment. Technical features & accessories: - Internal coolant system 40 bar - Dual pallet changer 500mm x 500mm with clamping tower and zero-point clamping system (Quant) Accessories, tools, and clamping devices shown are only included in the scope of delivery if this is noted in the additional information. Subject to changes and errors in the technical data and specifications, as well as prior sale!

Condition: used, Year of construction: 2016, functionality: fully functional, machine/vehicle number: 2460062, Technical Specifications: Dwsdpfx Aoxw Syusggob # Machining Workspace: X 300 mm; Y 500 (725) mm; Z 375 mm # Axis Description: 3 Linear Axes (X, Y, Z) + 1 Rotational Table Axis (A-axis) with index divider head, equipped with direct angular measuring system, number of revolutions: 50 minˉ¹, accuracy +/- 5" # Maximum Clamping / Part Size: Ø 575 x 830 mm; maximum weight 360 kg # Rapid Traverse Rate: X/Y/Z: 65/75/75 m/min; Positioning Accuracy Tp: 0.008 mm # Distance Between Spindles: 300 mm # Spindle Speed: 1–17,500 rpm # Spindle Interface: DIN69893-HSK-A63 (with internal coolant supply) # Automatic Tool Changer: 2 x 32 tool positions, chip-to-chip average time: 2.5 sec # Max. Tool Dimensions: Ø75 mm / Maximum Length: 275 mm / Maximum Weight: 7.5 kg Electrical Specifications: # Voltage: 3x400V / 50Hz # Installed Power: approx. 85 kVA / 125A Dimensions: # Installation Footprint: approx. 3.6 x 6 x 3.7 m # Weight: approx. 10,500 kg Equipment Includes: # CNC Control: Siemens 840D SL # Linear Axis Measuring System: Heidenhain linear scales # Chip Conveyor: Knoll Type 550 K-1 # Oil Cooling System # High-Pressure Oil Filtration System (max 80 bar): Knoll VRF 450_2350 # Cooling System for Shaft, Guides, and Switchboard # 2 Oil Lubrication Units # Oil Vapor Extraction/Recovery System: IFS Vario E2000 (2,000 m³/h) # Fire Suppression System: Kraft & Bauer # Part Presence Detection: via low-pressure air sensors # In-Process Control: Marposs T25 # Tool Breakage Monitoring and Length Measurement: inductive sensor # Tool Holder Detection in Work Spindle Machine Condition: Operational

Condition: used, Year of construction: 2016, functionality: fully functional, machine/vehicle number: 2460065, Technical specifications: # Machining Workspace: X 300 mm; Y 500(725) mm; Z 375 mm # Axis Configuration: 3 linear axes (X, Y, Z) + 1 rotational table axis (A) and 2 rotational axes (B) with indexer head - Direct angular measuring system, maximum rotational speed: 50 min⁻¹, accuracy: +/- 5" # Maximum clamping/part dimensions: Ø 575 x 830 mm; maximum workpiece weight: 360 kg # Rapid traverse: X/Y/Z 65/75/75 m/min; positioning accuracy Tp: 0.008 mm # Spindle distance: 300 mm # Spindle speed: 1–17,500 rpm # Spindle taper: DIN69893-HSK-A63 (internal coolant supply) # Automatic tool changer: 2x32 tools, chip-to-chip average 2.5 sec # Maximum tool size: Ø75 mm / max. length 275 mm / 7.5 kg Electrical connection: # Voltage: 3x400V/50Hz # Installed power: approx. 85 kVA / 125A Dimensions: # Installation space: approx. 3.6 x 6 x 3.7 m # Weight: approx. 10,500 kg Equipment includes: # CNC control: Siemens 840D SL Dwjdpfjxw Ttijx Aggeb # Linear axis measuring device: Heidenhain linear scales # Chip conveyor/extractor: Knoll Type 550 K-1 # Oil cooling system # Oil filtration system max 80 bar: Knoll 550 K-1 450_2450 (can service 2 machines simultaneously) # Shaft cooling system, guideways, and control cabinet # 2 oil lubrication units # Oil vapor absorption/recovery system: IFS Vario E2000 (2,000 m³/h) # Fire protection: Kraft & Bauer # Part presence detection: with low-pressure air sensors # In-process control: Marposs T25 # Tool breakage monitoring and length measurement: inductive sensor # Toolholder detection system in working spindle # Documentation: Manuals only (printed) Machine condition: Operational / In working condition.

Condition: used, Year of construction: 2017, Technical details: x-travel: 560 mm y-travel: 560 mm z-travel: 660 mm control: Celos Siemens 840D SL Operate ERGOline Multitouch turning speeds: 20 - 20.000 1/min spindle drive: 25/ 35 kW max. torque on the spindle: 86 / 130 tool taper: HSK-A63 Number of tool station: 60 diameter of tools max.: 70 mm Tool diameter with no neighbouring tools: 170 mm tool length - max.: 450 mm weight of tools max.: 12 kg numbers of pallets: 2 Dedpfx Ageyqybbogswb Pallet dimension: 400 x 400 mm max. workpiece diameter: 630 mm workpiece height max.: 900 mm table load: 400 kg rapid travel x/y/z: 60 m/min Feed x/y/z: 60 m/min internal coolant system feed: 70 bar weight of the machine ca.: 8,5 t dimensions: 3200 x 4800 x 2900 mm Accerories Rotoclear window Signal lamp 4 colours Electronic handwheel Probe for tool breakage and length measuring Coolant shower Renishaw probe (spindle) Vorbereitung / preparation only HSK cone cleaning station with brushes Horizontal machining center with Siemens - Celos control, full b-axis, tool magazine with 123 pos. HSK-A 63, coolant through spindle 40 bar. The machine has just received a new milling spindle. *

Condition: ready for operation (used), Year of construction: 2011, travel distance X-axis: 1,100 mm, travel distance Y-axis: 900 mm, travel distance Z-axis: 1,250 mm, controller manufacturer: SIEMENS, controller model: 840D, total height: 4,000 mm, total width: 6,000 mm, table load: 1,500 kg, spindle speed (max.): 5,500 rpm, number of slots in tool magazine: 240, tool weight: 60,000 g, product length (max.): 6,000 mm, number of axes: 4, This 4-axis Burkhardt-Weber MCX750 M2 was manufactured in 2011. It features a substantial X-axis travel of 1100 mm, Y-axis travel of 900 mm, and Z-axis travel of 1250 mm. The machine has a maximum pallet load of 1500 kg and a magazine capacity of 240 positions. The machine is linked to a Burkhardt-Weber MCX750 M2 (2011) and a pallet magazine and set-up station (12 positions + 2 positions per machine + 2 set-up stations) Dwjdpszl S Uhofx Aggjb Contact us for further details. • Maintenance contract: Yes • Utilization: 70% • Shifts: 2 • Number of revolvers/magazines: 1 • Magazine capacity: 240 positions • Pallet size: 800 x 800 mm • Drive power: 50 kW • Maximum torque: 1650 Nm • Maximum tool length: 750 mm • Maximum tool diameter: 350 mm • Rated voltage 3x 400 V • Frequency 50 1/s • Full load current 150 A • Rated current main drive 85 A • Connected load 80 kW 100 kVA • Operating voltage 400 V • Control voltage 24 DC • Frequency 50 Hz • Power 2.9 kW • Current 11.0 A • Refrigerant R134a • Filling quantity 3.0 kg Additional equipment • OPTIONAL: Tooling package (approx.): • Group 1: 700–750 tools (Ø up to 124.9 mm) • Group 2: 100–150 tools (Ø 125–224.9 mm) • Group 3: 50 tools (Ø 225–350 mm)Geometry readjusted (done by official Burkhardt-Weber)The machine is linked to a Burkhardt-Weber MCX750 M2 (2011) and a pallet magazine and set-up station (12 positions + 2 positions per machine + 2 set-up stations) Technical Specification Taper Size SK 50

Condition: ready for operation (used), functionality: fully functional, Perfectly functional. Dedpfozfgitjx Aggswb

Condition: good (used), Year of construction: 2008, functionality: fully functional, travel distance X-axis: 1,400 mm, travel distance Y-axis: 1,200 mm, travel distance Z-axis: 1,350 mm, rapid traverse X-axis: 50 m/min, rapid traverse Y-axis: 50 m/min, rapid traverse Z-axis: 50 m/min, feed rate X-axis: 50 m/min, feed rate Y-axis: 50 m/min, feed rate Z-axis: 50 m/min, controller manufacturer: Mori Seiki (Fanuc), controller model: MSX-701 (Fanuc 31i), workpiece height (max.): 1,450 mm, workpiece diameter (max.): 1,450 mm, workpiece weight (max.): 2,200 kg, total height: 3,850 mm, total length: 7,200 mm, total width: 4,300 mm, spindle speed (max.): 8,000 rpm, coolant supply: 70 bar, type of input current: AC, Equipment: chip conveyor, documentation/manual, rotational speed infinitely variable, Offered here is a machining center from the manufacturer Mori Seiki. The machine is fully functional, in good condition, and can be inspected and tested at our facility. Manufacturer: Mori Seiki Model: NH8000 DCG Year of manufacture: 2008 Control unit: MSX 701-III Technical specifications: Travel distances X-Y-Z: 1400 x 1200 x 1350 mm B-axis: 0.001° Feed rate X, Y, Z: 50,000 mm/min Rapid traverse X, Y, Z: 50 m/min Pallet size: 800 x 800 mm Number of pallets: 2 Pallet change time: 16 s Max. workpiece weight: 2200 kg Max. workpiece diameter: 1450 mm Max. workpiece height: 1450 mm Dwsdpjyrdn Uofx Aggsb Spindle speed: 8000 rpm Spindle power: 37 kW Tool holder: HSK-A100 Tool magazine: 60 positions Tool change time: 1.9 s Distance between pallet surface and spindle center: 100–1300 mm Distance between pallet center and spindle nose: 100–1450 mm Total power consumption: 86 kVA Machine dimensions: approx. 7200 x 4300 x 3850 mm Transport dimensions machine: approx. 7000 x 3400 x 3300 mm Machine weight: approx. 30 t Total weight incl. magazine and accessories: approx. 37 t Scope of delivery includes: 1x Mori Seiki NH8000 DCG machine 1x Matrix tool magazine 1x chip conveyor 1x coolant system 1x transformer Various tool holders

Condition: used, Year of construction: 1995, functionality: fully functional, Year of manufacture: 1995 ▪ FANUC CNC control ▪ Travels: X 840 mm, Y 840 mm, Z 760 mm ▪ Djdpfx Ageywugyogjwb Milling spindle: 10,000 rpm ▪ Spindle motor power: 30 kW ▪ Spindle taper: ISO 50 (DIN 69871) ▪ Tool magazine with 60 positions ▪ No. 2 pallets, 630 x 630 mm ▪ Full-contouring rotary table (4th axis) ▪ Coolant through spindle, 40 bar with enlarged tank and paper filter ▪ Chip conveyor ▪ Tool presetting/presence probe ▪ Electronic handwheel (MPG) ▪ Weight: 18,500 kg X & Z axes rails and carriages replaced in 2022 Spindle line newly rebuilt in 2024 Tool changer gearbox newly rebuilt in 2024

Condition: used, Year of construction: 2012, 1 used 4-axis horizontal machining center Manufacturer: DMG Type: NHX 4000 Year of construction: 2012 Control: Siemens 840D SL Operate Technical details: X-axis travel: 560 mm Y-axis travel: 560 mm Z-axis travel: 660 mm Spindle speed: 20 - 12000 rpm Spindle motor: 25/35 kW Torque at the spindle: 86 / 130 Tool holder: SK 40 Number of tool magazine positions: 40 Maximum tool diameter: 70 mm Tool diameter with free adjacent positions: 170 mm Tool length - max.: 450 mm Maximum tool weight: 12 kg Pallet size: 400 x 400 mm Number of pallets: 2 Workpiece diameter - max.: 630 mm Workpiece height - max.: 900 mm Table load: 400 kg Rapid traverse rates x/y/z: 60 m/min Feed rates x/y/z: 60 m/min Internal coolant supply: 70 bar Machine weight approx.: 8.5 t Overall dimensions: 3200 x 4800 x 2900 mm Equipment: Production package with internal coolant supply (IKZ) at 40 bar Dwsdpfx Agezq R Tmsgsb

Condition: new, Year of construction: 2026, functionality: fully functional, spindle speed (min.): 12,000 rpm, spindle speed (max.): 36,000 rpm, High part output | 3D CNC milling for small workpieces up to 1000 x 800 x 400 mm. > Efficient milling spindle, short throughput times and high part output: Due to the highly efficient milling spindle, the 5-axis CNC machine creates a high part output. The CNC milling machine stands for absolutely fast production processes and short throughput times. In addition, the rotary table of the CNC milling machine performs the C-axis movement, making milling even more effective. > Little space required, fast commissioning: The RT-F 1400 CNC milling machine requires little space and can be commissioned within two days. Set-up times are minimal. The CNC machine can be easily moved to another location using a forklift. > First-class contour accuracy for 3D machining with fixtures: All components, such as milling tool, spindle and the machine are matched to each other and to the desired component. A fixture from HG GRIMME SysTech can additionally influence the milling quality. Existing fixtures can be reused at any time. > Use in industry and small businesses: The CNC rotary table milling machine RT-F 1400 is particularly suitable for 3D machining of smaller components (800x1000x400mm). The CNC milling machine is used just as successfully by large industrial companies, such as the automotive industry, as it is in small businesses. > Basic version of the CNC machining center - Protective cabin with automatic gate unit, pneumatic - Swiveling, integrated control panel - High-performance CNC control NUM Flexium+ with nPad and 19'' monitor - Tool changing system with 12 places, dust-tight - Tool measurement Renishaw-TS 27 R - chip tray, vacuum pump > 365 further equipment options - example CFK package The machine can be equipped with many further options. One example is the upgrade of the machine equipment for CFRP machining. The CFRP package takes into account many safety aspects that are necessary for the processing of composite material. We offer around 365 additional options across our entire product range and can further equip the basic machine offered at any time. > Suitable materials for the 5-axis CNC rotary table milling machine 1400: plastics, composites such as CFRP, model making materials, aluminum. Further technical data Cube dimensions component - 1000 x 800 x 400 mm (+162 mm substructure) Travels X/Y and Z - X/Y and Z: 1,040 x 1,400 mm x 725 mm Travels of rotary axes A and C - Rotary axis C (table) ± 1,080°. - Swivel axis A, standard tool spindle with tool changing system ± 110°. Speeds - Rapid traverse linear axes X/Y/Z 40/40/30 m/min - Rapid traverse rotary axes A/C 14,000°/18,000° m/min Accuracies - Positioning accuracy ± 0.040 mm - Repeat accuracy ± 0.035 mm Machine rotary table - ø 800 mm Table load - approx. 200 kg Djdpfx Ajx S Etmjggowb Milling spindle - High-frequency milling spindle 9 kW (S6) - High frequency milling spindle 8 kW (S1) - speed 36.000 rpm - Tool holder HSK 40 E Machine weight - approx. 3000 kg Already included special equipment - Head suction for floating dust and chips - Interior with perforated footboards - interior lighting - Ethernet and remote maintenance - 3D spline - Connection T-Box (nPad) (subject to change without notice)

Condition: used, Year of manufacture 1997 2 grid tables Working area X 3,900 mm Working area Y 1,600 mm Dwjdjw Uf N Sopfx Aggjb Working area Z 200 mm Additional images available

Condition: good (used), Year of construction: 2020, functionality: fully functional, operating hours: 5,800 h, travel distance X-axis: 1,250 mm, travel distance Y-axis: 1,200 mm, travel distance Z-axis: 1,100 mm, workpiece height (max.): 1,400 mm, workpiece weight (max.): 2,000 kg, controller manufacturer: Siemens, controller model: 840D SL, torque: 1,146 Nm, rotational speed (max.): 8,000 rpm, Machine name / type: HELLER / H 8000 Operating hours: 5800 Year of construction: 2020 Dedpju Urgbefx Aggjwb Control unit: Siemens 840D SL Spindle: EPC-Unit (8.000 1/min, 60 kW, 1146 Nm) Tool clamping system: HSK 100 Tool magazine / places: Chain / 100 Rotary table: 360.000° X 0,001° Coolant unit: KNOLL, KF 600, IKZ 70 bar, (work area flushing) Positioning range XYZ (mm): 1250 / 1200 / 1100 Pallet size (mm): 800 X 800 Workpiece clamping: mechanical Additonal options / Specifics: multi-spindle-head support (MSK); receiver for measuring probe (RENISHAW); fast drill fracture sensing (SBBK); interface exhaust system; screen blow-off device for operator door; codechip; Chip conveyor function check; Integrated process monitoring (IPM) + Monitoring function to minimize machine damage in case of collision; 3 colour status lamp; increased tool weight 35kg; scraping conveyor for wet machining; Coolant temperature control; Feed force display; Tangential control;

Condition: excellent (used), Horizontal machining center OKK Djdpjzr Ilvjfx Aggswb Rotary pallet system Type HM600 CNC Fanuc series 310IS-Model A Tilting and fork-liftable chip conveyor from GOUBARD Tool holders, double-sided (60) Coolant tank

Condition: good (used), Year of construction: 2003, functionality: fully functional, travel distance X-axis: 870 mm, travel distance Y-axis: 710 mm, travel distance Z-axis: 660 mm, rapid traverse X-axis: 50 m/min, rapid traverse Y-axis: 50 m/min, rapid traverse Z-axis: 50 m/min, controller model: Fanuc 16iMB, workpiece height (max.): 1,100 mm, workpiece diameter (max.): 800 mm, workpiece weight (max.): 600 kg, spindle speed (max.): 15,000 rpm, number of slots in tool magazine: 50, Equipment: chip conveyor, rotational speed infinitely variable, Specification Value Machine Type 4-Axis Horizontal Machining Center Pallet Size 500 x 500 mm Number of Pallets 2 (Automatic Pallet Changer) Table Load Capacity 800 kg X-Axis Travel 870 mm Y-Axis Travel 710 mm Z-Axis Travel 660 mm B-Axis 0.001° Indexing Spindle Speed 15,000 rpm Spindle Taper SK40 Gearbox Yes Dwedpfsy Uvlfsx Aggjb Spindle Type Gear Driven Spindle Motor Power Approx. 26 kW Rapid Traverse Rate 50 m/min Tool Magazine Capacity 50 Tools Tool-to-Tool Time Approx. 1.5 sec Maximum Tool Weight 20 kg Through Spindle Coolant Yes Chip Conveyor Included Machine Weight Approx. 20,000 kg Kitamura HX500i Alpha horizontal machining center in very good technical condition. Machine equipped with 15,000 rpm gearbox spindle, SK40 spindle taper, automatic pallet changer (2 pallets), chip conveyor, through-spindle coolant system and FANUC 16i-MB CNC control. Suitable for precision machining and demanding production applications.