Year of construction: 1992, Condition: good (used), Extraction system, make KELLER LUFT-TECHNIK Type: UNI-STAR X-SL, year of manufacture 1992 Motor 3.3 KW Max. air volume flow/h 2,300 De Iaji E Td Ho Stpysut Filter area 30 m2 8 cartridge filters are installed. Dimensions 0.9mX1mX3.5m, weight approx. 1000 kg. Ready for use in good condition.

Condition: new, Year of construction: 2024, Gold River SWZ-700 water separators Application description: The GOLD RIVER SWZ series separator has been designed for special tasks, it can cope with the most difficult materials that contain many properties that disturb the separation process in separators commonly available on the market. SWZ water separators separate heavy fractions (non-ferrous metals) from, among others, plastics in the process of recycling secondary raw materials. SWZ separator equipped with a four-section copper water system equipped with radial nozzles with variable linear geometry. The separator uses the latest divided type of separation mat. The development of a modern module for preliminary division and preparation of material guarantees the purity of recovered raw materials in a very short time (plastics, metals). Why a water system? Our device uses a system similar to that used in the gold recovery industry. We use water as a carrier and a force that affects the materials in a gentle way. In the water system, all particles with higher mass are gently washed out and separated, generating no losses during the entire separation process. The properties of water together with our proprietary solutions are unrivaled compared to, for example, air separators. SWZ type separators are used: Separation of heavy from light materials (metal granulates contaminated with plastic, foil, paper, cotton, fibers) Cleaning plastics after air separators (dry) Separation of metals in cable and non-ferrous metal recycling lines The SWZ-700 water separator, thanks to the use of the latest module, performs the separation process in a very short time, therefore it is characterized by a high hourly efficiency of separated material of approximately 1200 kg/h. Description of action: The material fed into the separator goes through the transport channel to the module for initial fraction division into its mass and humidity changes. Some of the material is separated at this stage. In the second part of the module, the humidity of the remaining batch changes. Then the material falls onto the separation table where the final fraction separation takes place. As a result of this process, we obtain valuable materials from both sides of the separator. Construction description: The massive structure and the inertial drive of the separator are made of materials appropriately selected to withstand the overloads resulting from vibrations. The supporting frame ensures excellent stiffness and failure-free operation for many years. Due to the type of vibration drive, the design does not require the installation of a soil separator. Separation table equipped with hydraulic adjustment of the angle of inclination. The separation table has a special module for initial division of fractions into their mass and preparation for final separation. The water system has several water pressure valves. The water circulation in the separator is closed. There is no need for constant access to an external water source because the device works using the water already in the tanks. Based on experience and continuous research in our laboratories. We are able to provide you with separators individually adapted to the specific nature of the material being separated. In various versions and sizes. SWZ-700 separators are manufactured to individual order. Dus Ia Seua Tbwetpyot

Condition: as good as new (ex-display), Codition : Unused, year 2019 Brand : Rotodyne Asselbergs Type : CV-1120/900-D16 Weight : 1450 kilograms All employees speak Dutch, German and English Prices are exclusive of VAT Shipping is possible (surcharge) (Changes and errors in the technical data, information and Duo Ia Stjvxlw Tjpyst Prices and prior sale reserved

Condition: good (used), Briquetting press for aluminum chips / grinding sludge Motor: 4 kW Briquette diameter: 60 mm High pressing pressure: 2,500 kg / cm² Throughput up to a maximum of 60 kg / h Dus Ia Stst Ia Tkjpyet * Details after test

Condition: excellent (used), Year of construction: 2006, Functionality: fully functional, machine/vehicle number: 515098K, I am selling a used SBM cone crusher, V8, manufactured in 2006. Duo Ia Stjv Sqdrspyst

Condition: used, Year of construction: 2021, operating hours: 200 h, Functionality: unexamined, Equipment: Methor chain basic package Track chassis including 2 driving speeds Chain 400mm 3-bar Additional hydraulic connection 70 l/min 24-V electric control Large radio remote control complete Maintenance-friendly engine compartment with LED light Folding hopper with path sensor and automatic control Hydraulically reversible fan wheel Acoustic start-up warning Fuel tank 300 liters Paint: RAL 2011 deep orange Additional equipment: Rubber quick-change pad De Ia Stovnq Trjpyjut Engine Cat C7.1, 205 kW Rear conveyor 6.9 m Crushing system size L (8 teeth) Frame for overband magnet Overband magnet Roller quick-change system on the roller Roller quick-change system on the machine Irrigation LED work lighting Additional electric pump for operation when the engine is not running

Condition: used, machine/vehicle number: 22031, Vertikale Ballenpresse / Vertical Waste Baling Press Pöttinger MP 600 ASerial-No. 5110176 Duo Ia Stjiiv S Sopyst Einfüllhöhe / Loading High max. 1070mm Einfüllöffnung / Filling opening 700 x 500mm Presskasten / Pressing box 700 x 500 x 900mm Ballenformat / Bale format max. 700 x 500 x 500mm Ballengewicht / Bale weight 40 - 80Kg Anzahl Umreifungen / Vertical binding 2 Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Year of construction: 2022, Condition: new, ZLOMIARZE Recycling Technology - LRK Recycling line The Mini Line is a high quality set of devices designed for the recycling process. Shredding and separation are essentials in this business, that’s why Mills from TORNADO series was designed for rapid reaction on feeding materials with being in a chamber for short time. Suitable sieves placement and balanced cutting rotor RPM provide uniform material fraction. Innovated implementation of water system with adjustable pressure in the Wet Separators GOLD RIVER series provides highly accurate separation of difficult materials. ❖LRK - 50 The set consists: • 11kW Grinding Mill – Tornado 400 • Compact Dust collector • Transport Conveyor • Wet Separator – Gold River 300/1250 Technical Specification: • Complete Set Power – 13 kW • Supply – 400 V ; 50 Hz • Performance – 50 kg/h (this is a real value, checked on basic materials). • Dimensions – 3500 × 600 × 1950 mm • Weight – 950 kg ----- ❖LRK - 100 The set consists: • 15kW Grinding Mill – Tornado 500 • Compact Dust collector • Belt Conveyor • Wet Separator – Gold River 500/1250 Technical Specification: • Complete Set Power – 20,2 kW • Supply – 400V ; 50Hz • Performance – 100 kg/h (this is a real value, verified on basic materials). • Dimensions – 5000 × 4000 × 2000 mm • Weight – 1300 kg ----- ❖LRK - 200 The set consists: • 15 kW Grinding Mill – Tornado 500 • Dual dust collector • 1st line belt conveyor • 18,5 kW Grinding Mill – Tornado 500 • 2nd line belt conveyor • Wet Separator Gold River 500/2500 Technical Specification: • Complete Set Power – 40kW • Supply – 400V ; 50Hz • Performance – 200 kg/h (this is a real value, checked on basic materials). • Dimensions – 5000 × 4000 × 2000 mm • Weight – 1300 kg ✔Spare parts included. Recyclable resources: ✔ Any kind of Aluminium cables ✔ Automotive cables with adhesive tape ✔ Cords and network cables ✔ Coax cables, Christmas lights ✔ Copper cables lined with gel or silicone ✔ Winding coil of a thickness 15 microns, contaminated with adhesive paper or plastic Dj Ijhix Daea Stpyeut Contact us for more information!

Condition: used, Year of construction: 2002, Functionality: fully functional, machine/vehicle number: 22924, Exhaust air dedusting system You are welcome to visit us by appointment. Dus Iajv Scfuo Stpyot

Condition: excellent (used), Year of construction: 2015, operating hours: 289 h, Functionality: fully functional, tank capacity: 32,000 l, filling opening length: 1,320 mm, filling opening width: 1,700 mm, power: 15 kW (20.39 HP), usable tank capacity: 32,000 l, transport height: 2,600 mm, Hello, we are offering you, subject to change, a used wood screw compactor with primary crusher and front press container from the manufacturer Ludden & Mennekes Entsorgungs-Systeme GmbH, Germany, type SVS 15. The following technical data was taken from the manufacturer's operating instructions and brochures, for which we cannot guarantee their accuracy or completeness. Technical data for the screw compressor: Dimensions of the filling opening 1320 x 1700 x 1100 mm (W x D x H) Dimensions of the base body 2445 x 2492 x 1430 mm (W x D x H) Dimensions of the complete screw compressor 2445 x 2492 x 2530 mm (L x W x H) Diameter of the outlet opening 700 mm Height of the clamps 750 mm Speed of the screw min. 16 rpm. Diameter of the screw 500 - 750 mm Torque of the screw 8,400 Nm Throughput approx. 90 m³/hour Drive power 15 kW, with 63 A Cekon plug Technical data for the front press container: Manufacturer Ludden & Mennekes Entsorgungs-Systeme GmbH, Germany Type PCS 6500 Dus Isvza Dgja Stpyot Year of manufacture 2015 Front press container 6500 (7170) x 2500 x 2600 mm (L x W x H) Volume of front press container 32 m³ Front press container empty weight 3820 kg Permissible total weight of the front press container 15000 kg The machine documentation is available in German. A viewing is possible by appointment. We would be pleased if this machine is of interest to you. Your service team Mertens & Frowein GmbH

Condition: used, Year of construction: 2010, operating hours: 9,100 h, Hello, I have for sale a Doppstadt AK 630 high-speed hammer shredder/chipper with a sieve from 2010. Mileage is 9,100 mth. The machine is in very good condition. I invite you to purchase. Duj Iov Unq Uoa Stpyet

Condition: used, Year of construction: 2021, operating hours: 4,540 h, Functionality: unexamined, Equipment: Basic package Inventhor Type 9 MTU diesel engine 6R1300, 390 kW at 1,700 rpm meets EUROMOT V emissions standard Additional hydraulic connection 30 l/min and 70 l/min Roller drive via planetary gear 380 kW – VARIO - Duo Isvnmldsa Stpyjt Load sensing system Fuel tank 950 liters Longitudinal belt: belt length 4,450 mm, belt width 1,000 mm Centrally arranged lubrication strips 24 V electric control Additional electric pump for operating the following functions when the engine is not running. Raise/lower/fold rear belt, open/close comb flap, open/close comb, raise/lower optional permanent magnet belt, raise/lower optional folding funnel Radio remote control complete Large side GRP maintenance doors Maintenance-friendly engine compartment with LED light Hydraulically reversible fan wheel Loading protection on both sides Fire extinguisher Maintenance ladder Tool box Acoustic start-up warning Doppstadt telematics system Paint: RAL2011 deep orange Special equipment: 500 mm chain chassis unit Chain chassis 500 mm flat Crushing system size "L" -VARIOMAT Size "L" - "Limiter" (20 pieces) Rear conveyor length 7 m 1200 mm wide LED light package engine compartment and rear Irrigation with funnel attachment H=300mm Frame for overband magnet Overband magnet 2 t permanent

Condition: used, Year of construction: 2003, Kanalventilator Absaugung - Duct Fan Coral PAP HP 7,5 (Absaugung - Extraction) Baujahr / Year 2003 HP 7,5 REVS 2800 HZ 50 VOLT 380 / 660Zum Absaugen von Holzspänen oder Papierresten For vacuuming wood chips or paper residue Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect De Ia Stpeiqtq Noyeut On Stock Emskirchen / Nürnberg - Can be test

Condition: used, The company sells SPE Renergi Low Temperature Dryer -The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. -The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. -Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. -Power supply Data: -Voltage 400 V AC, three phase -Recommended fuses in supply line: maximum 3x630 A -Typical power consumption: 200kW -The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). -Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. -Airflow: max 200 liter/min -Air pressure: min 4,5 bar, recommended 6,0-8,0 bar -Water supply: hot water supply, with a flow of 32 dm3/s. -Water pressure: min 1.5 bar, max 6.0 bar -Operating temperature range: -Incoming air temperature: -20°C to 50°C -Relative humidity: 0% to 60% -Raw material/media: -Relative humidity: 45% to 55% by wieght -Requested relative humidity: 8% to 15% in the dried material -Capacity: -The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load -The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. -SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: -The Machinery Directive 2006/42/EC -LVD 2006/95/EC -EMC 2004/108/EC -The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. -The dryer is already dismantled -All electrical schematics, manual, operating instructions available Duo Ia Stsrb A R Nspyot -Upon request, we can provide a contact person with this type of working dryer for consultation

Condition: used, Year of construction: 2017, operating hours: 6,584 h, Functionality: unexamined, Equipment: Basic version DW 3060-F "Buffalo" (carrier machine) Central axle trailer chassis with 3 axles, 80 km/h road approval Braking system including ABS and lighting in accordance with EC directive 50 mm EC towing eye including slip-on shoe Hydraulically adjustable support leg Splash guard (inside and side fenders) Permissible total weight 25,000 kg Tires 385/65 R22.5 Mercedes-Benz/MTU diesel engine 6R1300, 360 kW at 2,000 rpm, meets EUROMOT IV emissions standard Reinforced planetary gear 380 kW Additional hydraulic connection 20 l/min Hydraulic preparation for drive Fuel tank 2 x 300 liters Rear conveyor: conveyor length 5,500 mm, conveyor width 1,200 mm, hydraulically foldable, with anti-magnetic middle section Longitudinal belt: belt length 3,300 mm, belt width 1,000 mm Centrally arranged lubrication strips 24 V electric control Reversing of the roller using an electric motor when the engine is stopped Automatically reversible fan wheel Chassis with level control Acoustic start-up warning Doppstadt telematics system Paint: RAL2011 deep orange Additional equipment: Hydraulic drive SHREDDING SYSTEM SIZE "L" 600/4 KPL. Additional hydraulic connection 70 l/min Due Iasvnmfqe Stpyst Radio remote control Comb extension size "L" limiter Mounting comb extension limiter size "L" Overband magnet for rear belt Frame for overband magnet Moistening device

Condition: used, Year of construction: 2001, machine/vehicle number: 64031, Kanalventilator Absaugung - Duct Fan ZENNER VTZ 560/50/2-W (Absaugung - Extraction) Baujahr / Year 2001 - Serial-No. 64.031 Volumenstrom / volume flow 2.21 m3/s Totaldruckerhöhung / total increase of pressure 3880 Pa Dichte / density 1.2 kg/m3 Drehzahl / Speed 2920 min-1 Kupplungsleistung / required performance 14.4 kW Duo Ia Seiqtqzstpyjt Temperatur / temperature max. 80°CZum absaugen von Holzspänen oder Papierresten For vacuuming wood chips or paper residue Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Condition: good (used), Year of construction: 2020, operating hours: 590 h, Functionality: unexamined, Equipment: Dus Ia Stevnq Rkepyst Methor chain basic package Track chassis including 2 driving speeds Chain 400mm 3-link Additional hydraulic connection 70 l/min 24 V electric control Large radio remote control complete Maintenance-friendly engine compartment with LED light Folding hopper with position sensor and automatic control Hydraulically reversible fan wheel Acoustic start-up warning Fuel tank 300 liters Paint: RAL 2011 deep orange Additional equipment: Rubber quick-change pad Engine Cat C7.1, 205 kW Rear conveyor 6.9 m Frame for overband magnet Overband magnet Roller quick-change system on the roller Roller quick-change system on the machine Irrigation LED work lighting Additional electric pump for operation when the engine is not running Fire extinguisher GN 9 A-3 DIN EN 3

Condition: used, Year of construction: 2003, Kanalventilator Absaugung - Duct Fan Coral PAP HP20 (Absaugung - Extraction) Baujahr / Year 2003 HP 20 REVS 2800 HZ 50 VOLT 380 / 660Zum Absaugen von Holzspänen oder Papierresten For vacuuming wood chips or paper residue Online-Video-Inspection by Skype-Video Due Ia Stpjiqtq Eeyet We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Condition: good (used), Year of construction: 2020, operating hours: 881 h, Functionality: unexamined, Equipment: Methor chain basic package Track chassis including 2 driving speeds Chain 400mm 3-bar Additional hydraulic connection 70 l/min 24-V electric control Large radio remote control complete Maintenance-friendly engine compartment with LED light Folding funnel with path sensor and automatic control Hydraulically reversible fan wheel Acoustic start-up warning Dj Ia Sovnmmzetpysut Fuel tank 300 liters Paint: RAL 2011 deep orange Additional equipment: Engine Cat C7.1, 205 kW Rear conveyor 6.9 m Frame for overband magnet Overband magnet Roller quick-change system on the roller Roller quick-change system on the roller Irrigation LED work lighting Additional electric pump for operation when the engine is not running Fire extinguisher GN 9 A-3 DIN EN 3

Condition: good (used), Year of construction: 2021, operating hours: 2,954 h, Functionality: unexamined, Equipment: Basic package AK 640 SA Mercedes / MTU diesel engine 6R1500, 480 kW at 2,000 rpm Semi-trailer chassis with 3 axles, 80 km/h road approval Braking system including ABS and lighting in accordance with EC directive Tires 385/65 R22.5 Permissible total weight 32,000 kg Hydraulically adjustable support feet Splash guard (inside fender and side) Mercedes / MTU diesel engine 6R1500, 480 kW at 2,000 rpm meets EUROMOT V emissions standard Additional hydraulic connection 20 l/min Load-dependent control of material feed including automatic scraper floor reversing Ds Isvna Daea Stpyjut Separate drive of feed roller and scraper floor (twin drive) Fuel tank 2 x 450 Liter Feed roller: length 1,690 mm, diameter 510 mm, with attached tooth segments Four-row flail drum with 36 freely swinging cast steel flail holders and replaceable flail tips Standard: flail tip Streusel plus Baffle plate with teeth Centrally arranged lubrication strips Electric pump for operating the cylinder functions (e.g. Raise/lower support feet and open/close rear basket, fold/unfold rear conveyor, release drive) when the engine is stopped 24-V electric control Separate control box at the rear of the machine Hydraulically foldable fine shredding basket Multimesh (mesh size between 30 - 280 mm, gradation on request) including 1-part rear flap Rear conveyor: conveyor length 7,500 mm, conveyor width 1,500 mm, discharge height 5,200 mm hydraulically foldable and lowerable from 39 degrees to 30 degrees, including anti-magnetic middle section Lower conveyor: conveyor length 3,800 mm, conveyor width 1,400 mm Moistening device for external water connection Scraper floor with 71 strips Wear protection in the drum area Reinforcement plates on the filling funnel (made of wear-resistant steel) on both sides for Side wall Radio remote control complete Fire extinguisher Acoustic start-up warning Doppstadt telematics system Paint: RAL 2011 deep orange Additional equipment: Hydraulic drive Scraper floor chain lubrication NEODYM overband magnet Frame for overband magnet Central lubrication Engine compartment protection plate Light package: engine compartment and rear conveyor

Condition: ready for operation (used), Year of construction: 2021, operating hours: 500 h, Functionality: unexamined, Basic package Methor chain - Crawler chassis including 2 driving speeds - Chassis chain 400mm 3-bar - Additional hydraulic connection 70 l/min - 24-V electric control - Large radio remote control complete - Maintenance-friendly engine compartment with LED light - Folding hopper with path sensor and automatic control - Hydraulically reversible fan wheel - Acoustic start-up warning - Paint finish: RAL 2011 deep orange Duo Ia Stpjvnah Sjyet Additional equipment: Engine Cat C7.1, 205 kW Rear conveyor 6.9 m Crushing system size L (8 teeth) Frame for overband magnet Overband magnet Roller quick-change system on the roller Roller quick-change system on machine Additional electric pump for operation when the engine is not running

Condition: ready for operation (used), Year of construction: 2022, operating hours: 207 h, Functionality: unexamined, Basic package Methor chain Track chassis including 2 driving speeds Chain 400mm 3-bar Additional hydraulic connection 70 l/min 24-V electric control Large radio remote control complete Maintenance-friendly engine compartment with LED light Folding hopper with path sensor and automatic control Hydraulically reversible fan wheel Acoustic start-up warning Paint: RAL 2011 deep orange De Ia Stpovm U Tgjysut Special equipment: Crushing system size L (8 teeth) Engine Cat C7.1, 205 kW Rear conveyor 6.9 m Frame for overband magnet Overband magnet Roller quick-change system on the roller Roller quick-change system on the machine Irrigation LED work lighting

Condition: used, Year of construction: 2021, operating hours: 1,345 h, Functionality: unexamined, Basic package Methor chain Track chassis including 2 driving speeds De Ia Stpsvm Uzdeyeut Chain 400mm 3-bar Additional hydraulic connection 70 l/min 24-V electric control Large radio remote control complete Maintenance-friendly engine compartment with LED light Folding hopper with path sensor and automatic control Hydraulically reversible fan wheel Acoustic start-up warning Paint: RAL 2011 deep orange Additional equipment: Engine Cat C7.1, 205 kW Rear conveyor 6.9 m Irrigation Crushing system size M (26 teeth) Roller quick-change system on the roller Roller quick-change system on the machine Frame for overband magnet Overband magnet

Year of construction: 2016, Condition: repair required (used), Functionality: unexamined, HS 800 basic package Do Ijvm Uqrea Stpyout Spiral shaft screen deck AA209-150 Special paint finish: Green

Year of construction: 2016, operating hours: 8,997 h, Condition: ready for operation (used), Functionality: fully functional, Basic version SM 620 Plus: Central axle trailer chassis with 2 axles, 80 km/h EU road approval Braking system including ABS and lighting in accordance with EC directive 50 mm EC towing eye, including slip-on shoe Hydraulically adjustable support feet Splash guard (inside and side fenders) Tires 435/50 R19.5 Permissible total weight 19,000 kg De Ia Stjvm S Iuepyout Deutz diesel engine TCD 3.6 L4, 90 kW at 2,000 rpm, meets EUROMOT IIIB / Tier 4i emissions standard Hydraulically reversible fan wheel on water and oil cooler Complete engine unit can be swiveled out Fuel tank 300 liters Filling funnel 5.0 m³ capacity Hydraulically foldable side belt: belt length 5,500 mm, belt width 1,000 mm Hydraulic foldable rear conveyor: conveyor length 5,500 mm, conveyor width 1,000 mm Hydraulic support cylinder between side and rear conveyor Emergency stop switch on side and rear conveyor Load-dependent controlled material feed from the conveyor floor to the screening drum Infinitely adjustable screening drum speed from 0 - 20 rpm Infinitely adjustable hopper conveyor speed from 0 - 0.17 m/s Switch box at the rear of the machine with the following functions: emergency stop switch, folding the rear conveyor in and out, folding the side conveyor in and out, folding the side conveyor in and out, bending the side conveyor and load control +/- Hydraulically foldable cleaning brush with individual brush elements and spring tines Centrally arranged lubrication strips 24 V electric control Underrun protection at the rear Side impact protection at the front (reinforced version) and on both sides of the rear Hydraulic quick coupling between the rear conveyor and the machine Acoustic start-up warning Paint finish: RAL2011 deep orange Basic version without screening drum Additional equipment: Additional hydraulic connection 20 l/min – DM Additional hydraulic connection 40 l/min – DM Magnetic roller for side belt Rear belt 3m with stone unwinding belt Wind sifter on 3m HB with 1.5m stone unwinding belt