Eccentric Press - Single Column

BALCONI 2 MT RS/L

Condition: excellent (used), Year of construction: 2010, feed length X-axis: 650 mm, feed length Y-axis: 500 mm, feed length Z-axis: 475 mm, feed rate X-axis: 6,000 m/min, feed rate Y-axis: 6,000 m/min, feed rate Z-axis: 6,000 m/min, table width: 450 mm, table length: 1,530 mm, X-Axis: 650mm Y-Axis: 500mm Z-Axis: 475mm Hjdpfxjxtmqts Aqpofn Table Length: 1530mm Table Width: 450mm Table load: 350 Spindle speeds: 55 - 4000Rpm Feed rate X-Axis:6000mm/min. Feed rate Y-Axis:6000mm/min. Feed rate Z-Axis:3000mm/min. Length: 2300mm Width: 2550mm Height: 2200mm Weight: 2850kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: refurbished (used), ECCENTRIC PRESS SGP TYPE : PEZZ 500/1700/1000 PRESSURE : 500t DOWN TABLE DIMENSIONS: 1700x1000mm LENGTH OF STROKE: 20-153mm DISTANCE BETWEEN RAM -TABLE: Min 700mm , Max 800mm WEIGHT: 40.000 kgr MADE IN AUSTRIA Hfedpfx Ajhqqnzeqpjn

Year of construction: 2008, condition: ready for operation (used), X-axis: 2500mm, Y-axis: 1270mm, positioning speed X-axis/Y-axis: 80/90m/min, simultaneous axis speed: 100m/min, punching capacity: 200kN, number of turret stations: 51, max. material thickness mild steel: 3.2mm, max. material weight at traverse speed F1/F4: 50/150kg, positioning accuracy: ±0.1mm, stroke rate X-axis: 350/min, stroke rate Y-axis: 260/min, max. stroke length: 42mm, max. feed speed X-axis/Y-axis: 80/60m/min, turret speed: 30rpm, compressed air requirement: 500l/min, operating air pressure: 5bar, connected load: 19kVA, length: 4165mm, width: 5120mm, height: 2082mm, height with mirror: 3028mm, weight: 13t, operating hours: 4531h, regularly maintained by the manufacturer, with documentation, without punching tools. An on-site inspection is possible. Hodjza E S Djpfx Aqpsfn

Condition: used, Year of construction: 1996, pressure 80 t throat 320 mm stroke 6 - 118 mm no. of strokes 30 - 80 Hub/min ram adjustment 70 mm table surface area 830 x 610 mm Hjdpfetycdkjx Aqpofn ram surface 650 x 400 mm column daylight (nach hinten) 630 mm total power requirement kW weight of the machine ca. 8,1 t dimensions of the machine ca. B 1,2 x T 1,9 x H 3,3 m Furnishing: - with gear transmission - fixed table - automatic stroke adjustment - automatic ram adjustment - hydr. Overload - Ejector - Grease central lubrication - Cover plate for drainage hole - Continuous speed control using a frequency converter - Machine is technically checked in our company and receives a new control cabinet with safety controls and touchscreen - current UVV test with braking time measurement

Condition: good (used), Year of construction: 1990, 1 used, well-maintained CNC tool milling machine, traveling column design, with CNC path control GRUNDIG Dialog 11 Table size 1600 x 675 mm Tool holder SK / ISO 40 Travel distances X-axis, longitudinal 1200 mm Y-axis, transverse 600 mm Z-axis, vertical 500 mm Table load 2000 kg Spindle speed range 20 – 6300 rpm Feed rate range, stepless 2 – 10,000 mm/min Rapid traverse in all axes 10 m/min Quill stroke 80 mm Drive power 100% ED 7.5 kW 40% ED 12 kW Machine dimensions L x W x H 3600 x 3000 x 2300 mm Machine weight 6800 kg Hedpfx Aqjhhuf Hepefn Control cabinet dimensions L x W x H 1700 x 900 x 1750 mm Control cabinet weight 470 kg Accessories / Special features: • CNC tool milling machine suitable for tool and fixture manufacturing, training, and mold making • CNC path control GRUNDIG Dialog 11 • Screen graphics, dialog-guided input, 3D linear interpolation, circular interpolation, helical interpolation, polar coordinate input, numerous drilling and milling cycles, cycle input graphically supported, milling cycles "contour pocket" for automatic free milling of irregular pockets, even with islands, shifting and rotation of the coordinate system • Electronic handwheel • RS 232 interface • Swiveling vertical milling head +/- 90° • Hydraulic tool clamping, DIN 2080 with clamping groove, Ott system • Quill adjustment 80 mm • Horizontal milling attachment • Full protection enclosure • Ball screw spindles in all 3 axes • Coolant system • Lighting Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 D - 44143 Dortmund - Wambel

Condition: used, Single-column – Eccentric press WEINGARTEN Type EV 63 Machine No. 738 / 61 Year of manufacture 1962 Pressing force 63 tons Stroke 260 mm Table area 630 x 530 mm Table opening Ø 210 mm Slide area 315 x 260 mm Adjustable slide stroke 8-100 mm Slide adjustment 63 mm Tool holder bore Ø 40 mm, with clamping piece Installation height max 450 mm Stroke rate 115 strokes / min Compressed air requirement min. 4.5 bar Motor power 4 kW Hsdpfx Aqek S Htxspsfn Power connection 380 Volt, 50 Hz Table height above floor approx. 750 to 900 mm - Electrical stroke release via foot switch or two-hand control - Overload protection by shear plate - Clutch-brake combination by WEINGARTEN friction-thread clutch with top dead center through-drive protection - Front crankshaft support bearing - Press table adjustable in height via 2 threaded spindles - Manual centralized lubrication - Control cabinet positioned beside the press - UVV (German trade association for accident prevention) for manual feeding operations Space requirement L x W x H 1750 x 1600 x 2430 mm Weight 4.5 tons Good condition

Condition: used, Year of construction: 1980, Technical details: pressure: 400 t stroke: 40 - 140 mm strokes / minute continous: 32 throat: 400 mm dayligth: min/max: 450/590 mm ram adjustment: 125 mm Hsdpfx Aqou N A Uujpjfn table-size: 1250x750 mm height over floor: 1130 mm total power requirement: ca. 31,5 kW weight of the machine ca.: 23,0 t machine dimensions LxWxH: 3,7 x 1,7 x 3,9 m dimensions electric cabinet LxWxH: 1,0 x 0,7 x 2,1 m further details: - clamping plate : L x W x H : 1260 x 760 x 100mm - with draw cushion device force 250kN, travel approx. 83mm - control via panel i.D. *

Condition: used, Year of construction: 1980, Technical details: rpm spindle (continous): 2000 - 2500 U/min double strokes/min.: 25; 37; 50; 75; 100 H/min. Grinding-wheel diameter: Ø 250 mm Hjdsu Ng I Eopfx Aqpefn work height max.: 1350 mm total power requirement: 2,7 kW weight of the machine ca.: 1,0 t dimension machine xH: 0,85 x 1,0 x 1,8 m Use for medium to larger metal circular saws from 250 - 1450mm. Saw blade attachment Ø 60 to Ø 80mm and shaft Ø 31,5mm Tooth pitch up to 42mm Tooth depth adjustment via scale Front cutting tooth: can be chamfered on both sides up to 45° and overcut at pitch 0.02mm *

Condition: used, Year of construction: 1990, x-travel 600 mm y-travel 400 mm z-travel 420 mm control TNC 355 Heidenhain Main spindle: Hfodotqmm Aspfx Aqpjn turning speed range - main spindle 20 - 4.000 min/-1 power capacity - main spindel 7 kW transmission ratio 3 tool taper SK 40 distance spindle /table 127 - 567 mm spindle diameter in front bearing 55 mm stroke of quill vertical 75 mm tool clamping 10 kN swivellable +/- 90 ° work table: table surface area 900 x 458 mm T-slots 7x 63 x 14H7 feeds: feed range 1 - 5.000 mm/min Feed force 5,4 kN rapid traverse ( X / Y / Z ) 7 / 7 / 6 m/min total power requirement 13 kW weight of the machine ca. 3,0 t dimensions of the machine ca. 4,0 x 4,0 x 2,1 m Tool Room Milling Machine - Universal HERMLE - UWF 900 E - Spindle-Head swivable +/- 90°

Condition: new, pressure 40 t throat 225 mm stroke 8-84 mm Table dimensions 580 x 450 mm ram adjustment 55 mm no. of strokes 130 Hub/min ram surface 185 x 180 mm ram hole 40 H7 mm hole in the table 210 x 170 mm T-slots 22 clamping plate 570 x 450 x 65 mm Hfodpfx Aob U Hwmeqpsn total power requirement 3,5 kW weight of the machine ca. 2,7 t dimensions of the machine ca. 1,4 x 1,1 x 2,1 m