Used lowboy semi-trailers / low loaders for sale (201)

Condition: new, maximum load weight: 45,250 kg, overall weight: 58,000 kg, axle configuration: > 3 axles, total width: 2,550 mm, Equipment: ABS, You can find our complete inventory of vehicles available for immediate and short-term delivery on our website. Excerpt from the equipment list. Full specifications available upon request. Chassis, stepped: * Special steel frame made from high-strength fine-grained steels, electrically welded at connection points * Generously dimensioned outer frame. 4-axle configuration * Wheel covers over the axles with spray suppression * All steel parts sandblasted * Side underrun protection made of anodized aluminum mounted * Increased point load approx. 30,000 kg over approx. 4,000 mm * Special construction in the stepped area for the longest possible low-bed length in combination with AluLeg drop supports instead of telescopic support legs, maximum rear swing clearance of the tractor unit approx. 2,100 mm Special body with rear stake extension: * DINKEL – special body * Self-supporting aluminum roof beam / profile approx. 120 x 100 mm, sliding roof with plastic flaps * Rear stakes extendable for loading/unloading up to approx. 4,200 mm * Three sliding stakes per side with elastic relief * Additional intermediate stake lockings in roof beam and parked position, via pull cable and spring bolt * DINKEL – mechanical lift roof, height-adjustable * Lift roof height approx. 400 mm, operable from both sides or one side without opening the opposite side * Additional height adjustment of approx. 480 mm in approx. 40 mm increments by adjusting the stakes * Front cover at bulkhead for driving operation under the tarpaulin up to a total height of approx. 4,400 mm * Four rows of stackable approx. 150 mm aluminum slats on the side, 450 pockets below, four rows of single pockets above. Only three rows of slats in the raised platform, spacings evenly distributed Floor: * Approx. 27 mm special waterproof bonded beech phenolic plywood, rough surface * Steel sheet in the wheel well area. Suitable for forklift traffic as per DIN standard * Outer frame flush with deck surface Brakes: * WABCO air brake system with EBS according to EC Directive 71/320, including PREV (Parking-Release Safety Valve) * Spring-loaded brake cylinders as parking brake * WABCO Smart Board with mileage counter and axle load display * Including WABCO tire pressure monitoring system Axles: * 4 x 10,000 kg SAF with drum brakes in low-loader design * Air suspension with lift and lower device, total lift approx. 230 mm * Third and fourth axles as friction-steered trailing axles with electric and mechanical lock Twin tires: * 235/75 R 17.5, 16-ply. Make of our choice, including spare wheel holder * Without spare wheel Lighting: * According to EU regulations, including LED side marker lights * Position lamps in LED design * 2 additional reversing lights * 2 work lights on the inside front wall, upper section Paintwork: * Chassis and body in one color, RAL 3002 carmine red * Intermediate stakes, axles KTL-coated black * Corner stakes hot-dip galvanized * Plastic parts black * Galvanized parts unpainted * Rims in factory silver Special equipment included: Cedpfx Apswx Dbiohjrd * 15-pin electrical supply cable * Air suspension in ECAS design, operated on the trailer * Oversize signage front and rear in galvanized, infinitely telescopic design with installed marker lights, including sockets for rotating beacons (small signs) * Additional external release for sliding roof frame lock * 4 stake adapters for special outer frame profile, to lock intermediate stakes as needed * PVC sliding tarpaulin, color similar to RAL 9

Condition: new, maximum load weight: 38,140 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately and at short notice, on our website. Excerpt from equipment. Full equipment details available on request. Gooseneck: - Gooseneck with front corners chamfered approx. 45° and rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, approx. 30 mm thick Loading area: - Telescopic loading area with rear incline approx. 1,000 mm x 8° - Between 1st and 2nd axle: one pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm (L x W x D) - Incl. 3-piece removable galvanized cover over wheel recesses (width approx. 670 mm – max. point load 5 t / pc.) - 1 pair of flat lashing rings at the front of the loading area (LC 10,000 daN) - 4 pairs of outward folding lashing rings (LC 5,000 daN) - 3 pairs of outward folding lashing rings (LC 10,000 daN) - Cutouts in the outer frame for attaching tie-down straps (LC 2,000 daN) Landing legs: - JOST landing legs (manual) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Tyres: - Tyres 235/75 R17.5 3PMSF, make at our discretion - TPMS tyre pressure monitoring system in accordance with ECE R 141 - Data transfer to the towing vehicle via standardised EBS interface as per ISO 11992 - For correct display, the towing vehicle must be able to receive and display this data Axles: - BPW axles and suspension, 2 axles rigid, 3rd axle self-steering - Technical axle load: 12,000 kg - Electromagnetic reverse lockout activated automatically when reversing and manually - Air suspension with lifting and lowering valve. Axle tools Braking system: - WABCO braking system according to EU regulations with EBS-E (2S2M) without piping to the tractor unit Electrical system: - Electrical system per EU regulations - LED lighting 24 Volt ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with the indicator - ASPÖCK-UNIBOX at front connection strip with 24N, 24S & 15-pin sockets, according to ISO; 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Steel construction: - Steel structure made of high-strength fine-grained steels - Steel qualities: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork: - Complete steel structure automatically shot-blasted after welding in a wheel-blasting system - Second shot-blasting with corundum for optimum coating adhesion Crsdpjw Tpq Dsfx Aphjd - HRM metallization of entire chassis with ZINACOR 850 (85% zinc/15% aluminium) for maximum corrosion protection - Final painting with 2 layers of 2K topcoat, single-colour in RAL 3002 Carmine Red, rear section metallized and painted in RAL 9010 Pure White - Metallic finish not available - Paint structure tested in salt spray test according to ISO 9227-NSS - Internal cavities sealed with special wax Including the following accessories: - On the gooseneck and rear, left and right, one holder for warning signs each, including socket - Spare wheel holder in front of the front wall (without spare wheel) - 2-inch king pin - Galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings on the galvanized front connection bar - Galvanized folding supports under the inclination at the rear of the loading area - A hardwood crash protection strip at the rear wall from gooseneck to the loading area - 1 pair of recessed lashing rings along the central beam at the rear inclination (LC 10,000 daN) - Aluminium drop sides and tailgate on the gooseneck

Condition: new, maximum load weight: 33,865 kg, overall weight: 48,000 kg, axle configuration: 3 axles, Equipment: ABS, You can find our complete range of vehicles, including those available for immediate delivery or on short notice, on our website. Below is an excerpt from the specification. The full equipment list is available upon request. Gooseneck: * Gooseneck with front corners chamfered approx. 45° and a rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Load area: * Double extendable design with rear bevel approx. 500 mm x 8° * 6 pairs of folding external lashing rings (LC 5,000 daN) * 4 pairs of folding external lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading area (LC 10,000 daN) * 1 intermediate table approx. 250 mm * Hardwood flooring approx. 48 mm thick, over axles with checker plate covering * Cut-outs in the external frame of the loading platform for attaching tie-down straps (LC 2,000 daN) Axles: * BPW axles and suspension, all axles forced-steered hydro-mechanically * Design axle load: 12,000 kg each * Air suspension with lift and lower valve * Axle tools included Tyres: * 245/70 R 17.5, load index (146/146 F) * Brand of our choice Landing legs: * JOST mechanical landing legs with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Braking system: * Braking system according to EU regulations with EBS-E (2S2M) without connection lines to the tractor unit Paintwork: First-class and durable corrosion protection * High-quality, one-colour 2-component (2K) topcoat in RAL 3002 carmine red * Rear section metallized and coated in RAL 9010 (pure white) Steel Structure: Steel construction from high-strength fine grain steels. * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: * Electrical system according to EU regulations * 24 Volt lighting ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets, compliant with ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Including the following additional equipment: * 2-inch kingpin * Galvanized steel front wall, approx. 400 mm high * Yellow-red air couplings at the galvanized front connection strip * Spare wheel carrier in front of the front wall * Electro-hydraulic unit * Rear and front steering via cable remote control with push-buttons, with single-track monitoring of the axles (without installation in the tractor unit) * Mount at the rear of the gooseneck for aluminum loading ramps Credpfx Apjw Tprzohsd * Removable aluminum ramp hanging rail at the rear of the vehicle * Galvanized folding supports beneath the slope of the load area * On the gooseneck: plug-in aluminum side boards and rear board, approx. 2,440 x 400 mm (L x H) * The rear galvanized stanchions are removable (body length approx. 2,560 mm) * One galvanized toolbox, integrated in the chamfered gooseneck * 4 pairs of WADER container pockets in the loading area for one 20', two 20', one 40' or one 45' container * 8 pairs of stanchion pockets (approx. 100 x 50 mm) in the external frame of the loading platform * Galvanized extensions, extendable by approx. 230 mm per side * Adjustable hanging rails for aluminum ramps at the rear of the vehicle * 2 pairs of ferry rings under the gooseneck and 2 pairs at the rear * Central lubrication system with 2 BEKAMAX (Pico) pumps, filled with standard grease NLGI-2 and removable pump guard * 2 LED reversing lights mounted on the rear panel * HRM Metallization (High Resistance Metallisa

Condition: new, maximum load weight: 48,300 kg, overall weight: 71,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including units available for immediate and short-term delivery, on our website. Extract from the equipment features. Full specification available on request. GOOSENECK: * Gooseneck with integrated 1-axle running gear (pendulum axle) in detachable design * Gooseneck hydraulically liftable and lowerable, including hydraulic coupling connected with the hydraulic axle compensation of the first axles * Length: approx. 5,200 mm, with a front taper of approx. 60° * Saddle load according to data sheet: W25-DSR2700-12/22.7 * For tractor units: 6 x 4 or 8 x 4 * Front bulkhead made of steel, detachable, approx. 400 mm high, with chamfered design * 1 pair of mechanical supports at the front of the gooseneck * ASPÖCK-UNIBOX on the front connection panel with 24N, 24S & 15-pin sockets * 1 spare wheel holder inside on the front bulkhead of the gooseneck with lifting arm * 2 pairs of recessed lashing rings on the gooseneck (LC 2,500 daN) * 2 pairs of recessed lashing rings in the outer frame of the front chassis, foldable outwards (LC 10,000 daN) * 1 pair of lashing rings at the transition between chassis and loading platform (LC 10,600 daN) * On the gooseneck, 1 pair of plug-in side aluminium drop sides, approx. 400 mm high, anodized finish * On the gooseneck, 1 plug-in aluminium tailboard, approx. 400 mm high, anodized finish * 3.5-inch king pin * TPMS tire pressure monitoring system compliant with ECE R 141 * Round NATO socket on the front connection panel (Maeler & Kaege VG 96 917) * 1 INOX toolbox with 1 lid, mounted on top of the gooseneck on the right in the direction of travel near the aluminium drop side, approx. 1,350 x 400 x 400 mm (L x W x H) LOADING AREA: * Lowbed with external main beams, designed as a telescopic loading platform in low-profile layout with front extension including a fixed approx. 50 mm hardwood floor * Length x width approx. 8,000 mm x 2,740 mm * Mechanical pin-lug coupling from the lowbed to the chassis to exchange the platform or install extension beams * 1 locking position every approx. 500 mm in the extension section Credpfx Aoyhkqnjphsd * 4 pairs of recessed lashing rings arranged lengthwise on the loading area, distributed along the outer frame/main beam (LC 10,000 daN) * 1 lashing ring per side on the outside of the rear crossmember (LC 10,000 daN) * Foldable widening sections, approx. 230 mm per side (WITHOUT timber planks) * Detachable widening planks, steel-edged * Preparation for installation of bolt-on container positioning devices for 1x 20' or 1x 40' container on the main beams. Container locks not included * 6 pairs of threaded blocks between the lashing rings under the upper flange on the main beam for mounting screw-type M24 rings (LC 8,000 daN) * 2 pairs of M24 screw rings (LC 8,000 daN) included REAR RUNNING GEAR: * Rear running gear with closed external frame, checker plate decking and continuous prism-shaped excavator recess, approx. 1,450 x 900 x 505 mm, open at rear * Pendulum axle, all axles hydro-mechanically forced steered * Hose burst valve on the axle compensation cylinders with automatic reset function * Hydraulic cylinders with shut-off cocks and pre-insertion facility for securing in raised position * Final paint on axles in 2 coats of 2-pack paint, solid colour DB 7350 Novagrau * Technical axle load: 12,000 kg each * Hydraulic axle compensation * 245/70 R 17.5 3PMSF. Brand at our discretion * Remote steering from front and rear via cable-control, with axle alig

Condition: new, maximum load weight: 37,075 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete range of vehicles, including immediately available and short-term delivery vehicles, on our website. Sample of the equipment. Full equipment details available on request. Neck (Gooseneck): * Gooseneck with front corners bevelled approx. 45° and rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading Platform: * Loading area behind the gooseneck hydraulically liftable and lowerable, length approx. 2,800 mm, with rear bevel approx. 1,000 mm x 8° * 6 pairs of external foldable lashing rings (LC 5,000 daN) * 2 pairs of external foldable lashing rings (LC 10,000 daN) * 1 pair of internal foldable lashing rings at the central beam front (LC 10,000 daN) * Cut-outs in the outer frame of the platform for hooking in tensioning straps (LC 2,000 daN) * Grating flooring C40/4 (point load approx. 2.3 t over an area of approx. 20 x 20 cm), treadplate flooring over the axles Two-piece Steel Ramps: * One pair of galvanized two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm, with grating surface C40/4 (point load approx. 2.2 t over an area of approx. 20 x 20 cm) * Ramp with hydraulically folding ramp sections * Hydraulic lift unit, hydraulically adjustable * Maximum load per pair: approx. 40,000 kg Landing Legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lift capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 fixed axles, 1 self-steering axle * Technical axle load: 12,000 kg each * Electromagnetic reversing lock automatic via reverse gear and manual activation * Air suspension with lift and lower valve Braking System: * WABCO braking system in compliance with EU regulations with EBS-E (2S2M) Tyres: Tyres 235/75 R 17.5 3PMSF – make at our discretion TPMS: * TPMS tyre pressure monitoring system according to ECE R 141 Paintwork: * HRM metallisation of the complete vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminium) to ensure maximum corrosion protection * Final coating with 2 layers of 2K topcoat, single-coloured in RAL 3002 Carmine Red as per RAL System 841GL * Rims in silver grey Accessories included: * 2-inch king pin * Galvanized steel front wall approx. 400 mm high * Grating in the gooseneck bevel C30/3 (point load approx. 2 t over an area of approx. 20 x 20 cm) * Grating in the platform bevel C40/4 (point load approx. 3.4 t over an area of approx. 20 x 20 cm) * Electric-hydraulic unit at the rear under the platform * Plug-in aluminium side and rear boards on the gooseneck, approx. 2,440 x 400 mm (L x H). Rear galvanized insert stanchions removable. (Body length approx. 2,560 mm) * Electric winch with radio remote control, approx. 5,400 kg lifting capacity, including approx. 9.5 mm thick steel cable, approx. 24 m long, with cable guide roller * Bolted approx. 5 t ring for winch cable loop on the neck without deflection pulley * One galvanized toolbox integrated in the sloped gooseneck with opening for a winch Csdpfjyhkrrjx Aphsrd * Grating on the gooseneck C30/3 (point load approx. 2 t over an area of approx. 20 x 20 cm) * 7 pairs of stanchion sockets for plug-in stanchions, approx. 100 x 50 mm, in the outer frame of the platform * Lift axle on the front axle, controlled by TEBS E depending on actual axle load and current loading status * 7 pairs of recessed lashing rings along the central beam (LC 5,000 daN): 2 pairs in the lift bed, 5 pairs in the rear section of the platform

Condition: new, maximum load weight: 39,720 kg, overall weight: 50,960 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Sample equipment features. Full specification upon request. Gooseneck * With beveled front corners approx. 45° and rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) Crodpfx Asu Sd U Ujphod * Hardwood flooring, approx. 30 mm thick Loading Platform Loading platform in extendable design * 5 pairs of fold-out outer lashing rings (LC 5,000 daN) * 3 pairs of fold-out outer lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading platform (LC 10,000 daN) * Recesses in the outer frame of the loading platform for securing straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick, over axles with chequer plate covering Landing Gear * JOST (mechanical) with 2-speed gearbox, approx. 24 t lift capacity (approx. 50 t test load) Axles * BPW axles: 2 fixed axles, 2 steering axles, drum brakes * Air suspension with lift/lower function * Self-steering axle with electro-magnetic reverse lock, activated via reverse gear or manually * Tires: 205/65 R 17.5 Brake System * Wabco brake system in accordance with EU directives with EBS-E (4S3M), without interconnecting lines to the tractor unit Steel Construction * Made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa), S690QL/S700MC (yield strength 690MPa) Paintwork * First-class, durable corrosion protection of the standard shot-blasted welded frame, guaranteed by a 2-component (2K) zinc dust primer * High-quality 2-component (2K) top coat, single-color, RAL 3002 Carmine Red * Rear section metallized and painted in RAL 9010 (Pure White) * Rims in silver Accessories Included * 2-inch king pin * Galvanized front steel bulkhead approx. 400 mm high * Spare wheel holder in front of bulkhead * Yellow-red air couplings on galvanized connector bar front * 4 wheel chocks with holder at bulkhead * Bracket at rear of gooseneck for aluminum loading ramps * Galvanized folding supports under inclined edge of loading platform * Holder for beacon at rear of trailer * Yellow reflective tape on sides, extension, and rear in accordance with EU regulations * Brackets for warning signs with socket on both sides at the gooseneck and rear panel * TPMS tire pressure monitoring system per ECE R 141. Data transmission to the tractor unit via standardized EBS interface according to ISO 11992; for correct display, the tractor unit must support data transmission and display * Plug-in aluminum side walls and tailgate on gooseneck, approx. 2,440 x 400 mm (L x H); rear galvanized stakes are removable (body length approx. 2,560 mm) * Galvanized toolbox, integrated in gooseneck slope * 6 pairs of WADER container locks in loading platform, for 1 x 20' container, 2 x 20' containers or 1 x 40' container * Sliding mounting rails for aluminum ramps at rear of vehicle * 7 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm, in the outer frame of the loading platform * Galvanized cross bracket under the loading platform * Galvanized extendable widenings, extendable approx. 230 mm per side * Lift axle on front axle, controlled via TEBS E according to current axle load and load status * 5 pairs of recessed lashing rings along the central beam (LC 5,000 daN)

Condition: new, maximum load weight: 36,400 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You will find our complete vehicle inventory, including immediately and soon-to-be available vehicles, on our website. Excerpt from the equipment. Full equipment details available upon request. - Gooseneck in SNT design to optimize load platform length, approx. 3,700 mm long, with a rear taper approx. 1,000 mm x 6° - For tractors: 4 x 2 and 6 x 2 - ASPÖCK-UNIBOX at the front connection panel with 24N, 24S & 15-pin sockets - 3 kW electro-hydraulic power pack for hydraulic operations (excluding hydraulic winches). Without supply line installation on the tractor unit - Outer beams of the gooseneck with mounting holes for boltable lashing rings. First hole approx. 200 mm from the front, subsequent holes approx. every 400 mm. 2 pairs of screw-in lashing rings included (LC 5,000 daN) - One mounting hole at the rear upper part of the gooseneck’s outer beams for a boltable lashing ring - 1 pair of screw-in lashing rings included (LC 10,000 daN) - 3 pairs of recessed lashing rings inside the gooseneck’s outer beams (LC 5,000 daN) - 3 pairs of recessed lashing rings in the center of the gooseneck (LC 5,000 daN) - 1 pair of recessed lashing rings at the rear center of the gooseneck (LC 5,000 daN) - Grating covering on the gooseneck and rear taper with 5 mm steel reinforcement - 2" kingpin - Round NATO socket at the front connection panel (Maeler & Kaege VG 96 917) - Spiral cable for powering the electro-hydraulic unit and/or electric winch (approx. 35 mm², approx. 3.5 m long) between trailer and tractor unit, with plug (NATO-NATO) - 1 pair of detachable aluminum side boards on the gooseneck, approx. 400 mm high, anodized finish Codpjyhkqujfx Apherd CARGO AREA: - Cargo area, approx. 9,600 mm long, with rear taper approx. 900 mm x 6° - Cargo area behind the gooseneck hydraulically liftable and lowerable, approx. 3,000 mm long, load capacity up to approx. 9,000 kg - TPMS (Tire Pressure Monitoring System) according to ECE R 141 - BPW axles and suspension, 1st and 2nd axles fixed, 3rd axle with trailing steering. 3rd axle with electromagnetic reverse lock via reverse gear and manual activation - Technical axle load: 12,000 kg each - Air suspension with lift and lower valve - 235/75 R 17.5 3PMSF twin tires. Brand of our choice, load index 143/141J (144/144F) - Mechanical landing legs with 2-speed gearbox and crank - Continuous grating flooring with approx. 5 mm steel plating for additional reinforcement, designed for point loads: on the lift bed and cargo area - Painted sand coating on the gooseneck cover plates as well as transition areas between neck and lift bed, lift bed and cargo area, and cargo area and ramps - 1 spare wheel mounting bracket under the cargo area to the right in front of the axles - Cut-outs in the outer frame of the cargo area and lift bed for attaching tie-down straps (LC 2,000 daN) - 11 pairs of recessed, fold-out lashing rings in the outer frame of the cargo area (LC 10,000 daN): 3 pairs in the lift bed outer frame, 8 pairs in the cargo area outer frame - 11 pairs of recessed lashing rings along the central beam (LC 5,000 daN): 3 pairs in the lift bed, 8 pairs in the rear cargo area - Control valves for the hydraulic ramps located on the right side of the vehicle - 1 pair of foldable mechanical rear supports, single-hand operation HYDRAULIC LOADING RAMPS: - 1 pair of two-part AXS steel ramps, approx. 4,920 mm long, and a

Condition: new, overall weight: 30,000 kg, axle configuration: 2 axles, loading space length: 13,590 mm, loading space width: 2,500 mm, loading space height: 1,820 mm, total width: 2,550 mm, total height: 4,000 mm, Year of construction: 2026, Equipment: ABS, Burgers Double Deck Trailer | 2-Axle Steered NEW More volume. Lower costs. More sustainable transport. Up to 60% more loading space compared to standard trailers. In many cases, replaces 3 trailers with 2 double deckers, reducing CO₂ emissions by up to 40%. Technical Data (Model: 2-axle steered) Chassis and Running Gear Design: 2-axle, steered * Axle system: TRIDEC TF-V02, mechanical steering without electronics * Air suspension with low-maintenance bushings, lift range +160 mm / -105 mm * Axle spacing: 1,400 mm * Axle load: 2 × 9,000 kg = 18,000 kg * Permissible gross weight: 30,000 kg (12,000 kg kingpin load + 18,000 kg axle load) * Tyres: 4 × Goodyear 385/65 R22.5 on steel rims * Wheelbase and axle position adjustable according to loading scheme Cedpfxsw I Iinj Aphsrd * Wheel housings with wear blocks and anti-spray mudflaps * Fully hot-dip galvanized chassis to ZINQ standard Brake and Safety Systems WABCO 2-line air brake system * Drum brakes 420 × 180 mm * ABS/EBS-E with ECAS (level control), ELEX, and RSS (electronic stability control) * Visible indicator lights for ABS/EBS and ECAS Dimensions External dimensions (L × W × H): 13,820 × 2,550 × 4,045 mm * Upper deck internal dimensions: Length 13,590 mm × Width 2,500 mm × Height 1,820 mm * Lower deck internal dimensions: Length 9,940 mm × Width 2,500 mm × Height 1,820 mm * Lower deck height from ground: 320 mm Bodywork and Materials Side walls: 21 mm plywood, coated inside and out with white polyester * Front wall: 24 mm plywood, both sides polyester white * Roof: 30 mm insulated polyester panel, white, with rainwater drainage * Floors: Aluminium profiles (top and bottom), non-slip, grey coated * Stainless steel front and corner profiles, L-profiles on side flaps Access and Operation Three side flaps (battery compartment, lift/smartboard control, technical access) * Multi-deck lift Dhollandia DH-VH (2,500 kg lifting capacity, hydraulic folding tip, LED platform lighting, foldable handrails and ramps) * Lift control: external operation on the right, integrated into the fence * Spare wheel not included Electrics and Lighting LED interior lighting upper and lower deck * Complete LED exterior lighting: position, marker, reverse, and work lights * Additional LED for platform lighting * Power supply via 2 × 230 Ah batteries, charging via tractor unit * Main switch behind side flap, coupled with lift control * WABCO Smartboard: weight display, odometer, adjustable loading/unloading heights Finish and Paintwork External colour: RAL 1003 yellow (non-metallic) including wheel wells, stainless steel front and rear * Reflectors: 3M partial contour marking (white sides, red rear) * Advertising space possible (optional) Benefits 60% more loading space – replaces up to 3 standard trailers with 2 double decks * 40% lower CO₂ emissions – eco-friendly and economical * ROI often within just 1 year * Customisable (axles, cooling, dimensions) * Suitable for long-haul and distribution transport Available Configurations at Burgers: 2-axle standard – rigid or steered, 13.60 × 2.55 × 4.00 m * 3-axle standard – rigid or with steered axle * City trailer – max. 11.50 m, always steered * Special dimensions – height up to 4.25 m depending on national regulations * Body: plywood or insulated, optionally with cooling and temperature zones * Extras: tail lift, hydraulic ramp, solar modules, cameras, aerodynamic profiles, LED packages For further information, we are happy to assist you.

Condition: used, functionality: fully functional, empty load weight: 16,300 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, first registration: 08/2018, suspension: other, tire size: 205/65 R 17,5, color: green, Equipment: ABS, EBS, - 5 axles: 1st axle friction-steered and liftable; 2nd–5th axle hydraulically steered Cedjymnmwopfx Apherd - Extendable: 6,200 mm (total length: 12,800 mm – 19,000 mm) - SAF axles - Sliding hydraulic double ramps with support legs - Lifting and lowering device - Drum brakes - Suspension: air-lift Errors and omissions excepted.

Condition: used, overall weight: 47,000 kg, axle configuration: 3 axles, first registration: 11/2004, next inspection (TÜV): 08/2026, * Müller Mitteltal TS3 low loader semi-trailer * First registration: 11/2004 Credpfx Apsyq A D Eehjd * 3 axles * Air suspension * Gigant axles * Hydraulically operated long ramps, extendable and foldable * Load width extensions from 2.50 m to 3.0 m * Loading length: 8.50 m at 0.85 m loading height * Loading length on neck: 3.40 m at 1.50 m loading height * Support legs * Unladen weight: 10,260 kg * Technical gross weight: 47,000 kg * TÜV valid until: 08/2026 * General inspection valid until: 02/2026

Condition: new, maximum load weight: 38,953 kg, overall weight: 49,500 kg, axle configuration: 3 axles, Year of construction: 2026, MAX100-N-3B-9.30-U Technical Data Speed: 80 km/h Total weight: 49,500 kg Saddle load: 18,000 kg Axle load: 31,500 kg Unladen weight (+/- 3%): 10,547 kg Payload approx.: 38,953 kg Gooseneck length: 3850 mm Saddle height loaded: 1200 mm Loading platform length: 9300 mm Extendable by: 0 mm Axle distance: 1360 mm Rear deflection radius: 2300 mm Loading height at max. load: 860 mm Overall width: 2540 mm Suspension travel: -55 / +145 mm Technical Description Gooseneck: Gooseneck with beveled front corners at 45° and a rear bevel of approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). Hardwood flooring, 30 mm thick. Csdpog Sk Trofx Apherd Loading platform: Loading platform after the gooseneck, hydraulically raisable and lowerable, length approx. 2,800 mm, with a rear bevel of approx. 1,000 mm x 8°. 6 pairs of lashing rings that can be folded outwards (LC 5,000 daN). 2 pairs of lashing rings that can be folded outwards (LC 10,000 daN). 1 pair of lashing rings that can be folded inwards on the central beam at the front (LC 10,000 daN). Cutouts in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN). Hardwood flooring approx. 48 mm thick, with non-slip steel plate flooring over the axles. Ramps: Two-piece steel ramps, one pair of galvanized two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm, with approx. 48 mm thick hardwood flooring. Ramp with hydraulically raising and folding ramp sections, hydraulic lifting mechanism and hydraulically adjustable. Maximum load per pair: 40,000 kg Kingpin: JOST kingpins (mechanical) with a 2-speed gearbox for a 24t lifting capacity (50t test load). Tires: Tires 235/75 R 17.5, as selected by the manufacturer. Axle: SAF axles, air-suspended, with drum brakes, with raising/lowering function. The last axle is steered with an electro-magnetic reverse steering lock, which can be activated via reverse gear or manually. Axle tool. Braking system: Braking system according to EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit. Steel structure: Steel structure made of high-strength fine-grained steels. Steel qualities: S355J2+N / S355MC (yield strength 355 MPa) S690QL / S700MC (yield strength 690 MPa) Painting: First-class and durable corrosion protection of the standard bead-blasted welded frame is guaranteed by a 2-component (2K) zinc dust primer. A high-quality 2-component (2K) topcoat in a single color in RAL colors of your choice. Rear part metallized and painted in RAL 9010 (pure white). Metallic paint is not possible. Electrical system: Electrical system according to EU regulations, lighting LED 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the connection bar at the front with 24N, 24S & 15-pin sockets. Connection according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Included accessories 2" kingpin One galvanized steel front wall, approx. 400 mm high. Yellow-red air couplings on the galvanized connection bar at the front. 4 pieces of wheel chocks with holders on the front wall. (± 5 kg) Cable for supplying the electro-hydraulic unit and/or the electric winch (35mm², 3.5 m long, max. 250A) between the semi-trailer and the tractor unit with plug connection (ANDERSON-ANDERSON) Galvanized folding supports under the bevel of the loading platform. One bracket for a rotating beacon on the rear of the semi-trailer. Operating valves for the ramps mounted on the right side of the semi-trailer. (± 4 kg) Yellow reflector tape according to EU regulations on the side and r

Condition: new, overall weight: 58,000 kg, Year of construction: 2026, Semi-trailer, drop-deck MAX100 4 A 8.60 U Technical data Speed: 80 km/h Total weight: 60,800 kg Fifth wheel load: 18,000 kg Axle load: 42,800 kg Unladen weight: Payload: Gooseneck length: 3,850 mm Fifth wheel height (loaded): 1,250 mm Loading area length: 8,600 mm Extendable by: 5,400 mm Axle distance: 1,360 mm Rear deflection radius: 2,300 mm Loading height (max. load): 860 mm Overall width: 2,540 mm Suspension travel: -55/+145 mm Technical description Gooseneck With beveled front corners at 45° and rear bevel of approx. 760 mm x 10° 3 pairs of lashing rings (LC 5,000 daN) Hardwood flooring, 30 mm thick Loading area in extendable design with rear bevel of approx. 1,000 mm x 8° 5 pairs of lashing rings, foldable outwards (LC 5,000 daN) 3 pairs of lashing rings, foldable outwards (LC 10,000 daN) 1 pair of lashing rings, horizontally mounted at the front in the loading area (LC 10,000) Hardwood flooring, approx. 48 mm thick, with diamond plate steel over the axles Ramps Two-part steel ramps One pair of galvanized two-part steel ramps, approx. 2750 + 1400 mm x 800 mm, with approx. 48 mm thick hardwood flooring Ramp with hydraulic up and folding ramp sections, hydraulic lifting mechanism and hydraulically adjustable. Maximum load per pair: 40,000 kg Tires 235/75 R 17.5 Braking system according to EU regulations with EBS-E (4S3M) without connection lines to the tractor unit Paintwork First-class, durable corrosion protection of the standard bead-blasted welded frame guaranteed by a 2-component zinc dust primer High-quality 2-component (2K) topcoat, solid color in RAL color shades of your choice Rear section metallized and painted in RAL 9010 (pure white). Fifth wheel: JOST fifth wheel (mechanical) with 2-speed gear for 24 t Lifting capacity (50 t test load) Steel construction made of high-strength fine-grain steels. Steel grades: Steel construction made of high-strength fine-grain steel S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Electrical system according to EU regulations, lighting LED 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the connection bar at the front with sockets 24N, 24S & 15-pole. Connection according to ISO. 24N ISO-1185 24S ISO-3731 15-pole ISO-12098 Accessories included: One galvanized steel front wall, approx. 400 mm high. 2" Kingpin 4 wheel chocks with holder on the front wall. One bracket for a rotating beacon on the rear of the trailer. SAF axles, two fixed axles, one steered axle, air-suspended, with drum brake, with lifting/lowering function. Cedeg Sk T Dspfx Aphsrd The trailing steered axle with electro-magnetic reverse lock, which can be activated via reverse gear or manually. Axle tool. Mounting in the rear area of the gooseneck for ALU support ramps. Galvanized folding supports under the bevel of the loading area. Mechanical locking of the locking of the loading area. One spare wheel with holder in front of the front wall. Yellow reflector tape according to EU regulations on the sides, on the extension and at the rear of the trailer. Yellow-red air couplings on the galvanized connection bar at the front. On the gooseneck and on the rear panel, one bracket each on the left and right for the warning signs including socket. One mudflap on the rear of the trailer. Manual and description On the gooseneck, plug-in ALU side and rear panels, approx. 2,440 x 400 mm (L x H). The rear galvanized plug-in posts are removable. Length of the superstructure approx. 2,560 mm, +/- 46 kg 3 pairs of WADER container po

Condition: new, overall weight: 47,000 kg, axle configuration: 2 axles, Year of construction: 2026, Technical Data MAX510-Z-2H-ATX-A-6.85-PA Speed: 80 km/h Total weight: 47,000 kg Saddle load: 23,000 kg Axle load: 24,000 kg Gooseneck length: 3750 mm Saddle height loaded: 1200 mm Rear overhang: 2300 mm Loading area length: 6,850 mm Extendable by: 5,500 mm Loading height at max. load: 350 mm Frame length: 2,600 mm Loading height, rear frame at max. load approx.: 1,005 mm Suspension travel: -150/+450 mm Axle track: 1360 mm Overall width: 2,540 mm Total weight depends on the saddle load. Low-bed: Low-bed with external, extendable beams. "SUPER LOW" design, length approx. 6,850 mm. Low-bed with fixed hardwood floor, approx. 40 mm thick, and mechanical locking mechanism. The supply lines are protected in the extendable beams and automatically adjust to the respective low-bed length. 5 pairs of lashing rings, foldable outwards (LC 10,000 daN). 6 pairs of threaded blocks on the inner beam for mounting screwable RUD rings. Rear frame: Rear frame with closed outer frame, diamond-plate flooring and continuous prism-shaped excavator well, approx. 1,250/700 x 505 mm, open at the rear. 2 pairs of lashing rings, foldable outwards (LC 10,000 daN). 1 pair of lashing rings lying in the well (LC 8,000 daN + 5,300 daN). 2 pairs of stake pockets for stake pockets 100 x 50 mm in the outer frame. Gooseneck: Gooseneck in SNT design for optimizing the Codpjizu Nwofx Aphjrd loading area length, length approx. 3,785 mm. Gooseneck hydraulically adjustable up/down and extendable. Technical saddle load: 23,000 kg For semi-trailer tractor: 4x2, 6x2 and 6x4 PENDULUM AXLE: "PENDULUM AXLE", all axles hydro-mechanically forced steered. Hose burst valve on the axle compensation cylinder with automatic RESET function. Hydraulic cylinders with shut-off valves and quick-release coupling for securing in the raised position. Final coating of the axles with 2 layers of 2-component paint, solid color in "FAY-Gray-34-0260". Technical axle load: 12,000 kg Hydraulic axle equalization. Axle tool. Braking system: Braking system according to EU regulations with EBS-E (2S2M) without connecting lines to the semi-trailer tractor. Electrical system: Electrical system according to EU regulations, lighting 24 volts ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection bar with sockets 24N, 24S & 15-pin. Connection according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel construction: Steel construction made of high-strength fine-grained steels. Steel grades: S355J2+N/S355MC (Yield strength 355MPa) S690QL/S700MC (Yield strength 690MPa) Painting: First-class and durable corrosion protection of the standard shot-blasted welded frame is guaranteed by a 2-component (2K) zinc dust primer. A high-quality 2-component (2K) top coat, solid color in RAL colors of your choice. Rear section metallized and painted in RAL 9010 (Pure White). Metallic paint not possible. Tires: Tires 245/70 R 17.5 3PMSF At the manufacturer's option. Load index (146/146F) Preparation for mounting screwable container positioning for 1 x 20' or 1 x 40' container on the outer beams. Without container locking mechanisms. i i2" Kingpin iA galvanized steel front wall, approx. 400 mm high. iA spare wheel with holder in front of the front wall. i2 pieces of wheel chocks with holder on the front wall. iYellow-red air couplings on the galvanized front connection bar. Steering from the front and rear by means of a cable remote control via push buttons, with single-axle control. (without installation in the semi-trailer tractor) i Hydrauli

Condition: new, maximum load weight: 36,461 kg, overall weight: 49,500 kg, axle configuration: 3 axles, total width: 2,480 mm, total height: 860 mm, Year of construction: 2026, Technical Description Gooseneck: Gooseneck with rear bevel of approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). 30 mm thick hardwood flooring. Loading Platform: Loading platform behind the gooseneck hydraulically liftable and lowerable, length approx. 2,800 mm, with rear bevel of approx. 1,000 mm x 8°. 6 pairs of outward-folding lashing rings (LC 5,000 daN). 2 pairs of outward-folding lashing rings (LC 10,000 daN). 1 pair of inward-folding lashing rings on the front central beam (LC 10,000 daN). Grating flooring C40/4 (point load 2.3 t on an area of 20 x 20 cm), over the axles with chequer plate covering. Two-Part Steel Ramps: One pair of galvanized, two-part steel ramps approx. 3,185 + 1,420 x 1,250 mm with grating flooring C40/5 (point load 8 t on an area of 20 x 20 cm). Ramp with hydraulically foldable ramp sections and hydraulic lifting system. Maximum load per pair: 40,000 kg In accordance with regulation 1230/2012/EU, ramps less than 300 mm in length do not count towards the vehicle length of 16,500 mm in driving position. Landing Legs: JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load). Tyres: Tyres 235/75 R17.5 3PMSF as per manufacturer’s choice. TPMS: TPMS tyre pressure monitoring system as per ECE R 141. Data transmission to the tractor unit via the standardized EBS interface according to ISO 11992. For correct display, the tractor unit must be able to receive and display these data. Axles: BPW axles and suspension, 2 fixed axles, 1 self-steering trailing axle. Technical axle load: 12,000 kg Electromagnetic reverse lock, activated via reverse gear and manually. Air suspension with raise and lower valve. Axle tools included. Brake System: WABCO braking system compliant with EU regulations with EBS-E (2S2M), without connecting lines to the tractor unit. Electrical System: Electrical system compliant with EU regulations, LED lighting 24 Volt ASPÖCK-NORDIK (ASS3). All LED side marker lights flash with the indicator. ASPÖCK-UNIBOX on the front connector strip with 24N, 24S & 15-pin sockets. Connection according to ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel Structure: Steel frame made of high-strength fine-grain steels. Steel grades: – S355J2+N/S355MC (yield strength 355 MPa) – S690QL/S700MC (yield strength 690 MPa) Tarp Structure: Tarp structure approx. 3,960 mm – Galvanized front wall with a tensioning mechanism for the sliding curtains. – “EDSCHA” roof, forward-sliding on aluminum roof rail profiles (bolted to front and rear walls). – 3 pairs of movable stanchions on the loading platform. Cjdpfow Dl Hwsx Aphjrd – Body can be hydraulically widened at the rear by approx. 750 mm to the left and right. – Sliding roof with upward-swinging portal carrier. – Sliding tarp with 700 mm length reserve and tensioning straps at approx. 600 mm intervals. Height to top edge of structure approx. 3,960 mm (loaded). – Driving with open sliding roof is not permitted and will cause damage to the tarp. Painting: Entire steel structure is automatically shot-blasted after welding using a blasting wheel system. Second blasting treatment with corundum for optimal coating adhesion. Full metallizing of the entire chassis with ZINACOR 850 (85% zinc / 15% aluminum) for best corrosion protection. Top coat with 2 layers of 2K finish, single-color in a shade of your choice according to the RAL 841GL standard. Rear section metallized and coated in RAL 9010 (pure white). No metallic paint.

Condition: new, maximum load weight: 36,156 kg, overall weight: 45,000 kg, axle configuration: 3 axles, Year of construction: 2026, MAX200-N-3A-13.60-19.5-2.54 Technical Data Speed: 80 km/h Total weight: 45,000 kg Fifth wheel load: 18,000 kg Axle load: 27,000 kg Unladen weight (+/- 3%): 8,844 kg Payload approx.: 36,156 kg Loading area length: 13,600 mm Fifth wheel height, loaded: 950 -> 1050 mm Rear overhang: 2,300 mm Extendable by: 3,400 mm Wheelbase: 1,360/1,405 mm Overall width: 2,540 mm Technical Description Loading area: Extendable loading platform with pneumatically operated locking mechanism. 2 pairs of lashing rings (LC 5,000 daN). 1 pair of lashing rings (LC 10,000 daN). 6 pairs of lashing rings, foldable outwards (LC 5,000 daN). 2 pairs of lashing rings, foldable outwards (LC 10,000 daN). Cutouts in the outer frame of the loading platform for attaching lashing straps (LC 2,000 daN). Fifth wheel: JOST fifth wheel (mechanical) with 2-speed gearbox for 24t Load capacity (50t test load). Axles: SAF axles: SAF CD axles, air-suspended, with disc brakes (377 mm), with lift/lower function (ET 120). The trailing axles with electro-magnetic reversing lock can be activated via reverse gear or manually. Axle tool. (± 80 kg) Braking system: Braking system according to EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit. Steel construction: Steel construction made of high-strength fine-grained steels. Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Painting: First-class and durable corrosion protection of the standard shot-blasted welded frame is guaranteed by a 2-component (2K) zinc dust primer. A high-quality 2-component (2K) topcoat, solid color, in RAL colors of your choice. Rear section metallized and painted in RAL 9010 (pure white). Metallic paint is not possible. Electrical system: Electrical system according to EU regulations, lighting LED 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the connection strip at the front with 24N, 24S & 15-pin sockets. Connection according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Included Accessories Yellow-red air couplings on the galvanized connection strip at the front. 2 chocks with holders. 2" King Pin Crsdpfsg Sk Tvjx Aphjd A galvanized steel front panel approx. 2200 mm high. (± 105 kg) EN12642-XL Yellow reflector tape according to EU regulations on the side, on the extension and at the rear of the trailer. European reflector signs (red-yellow) at the rear of the trailer. Loading area with approximately 38 mm thick hardwood floor. (± 320 kg) 10 pairs of pocket rails for plug-in rails 100 x 50 mm in the outer frame of the loading platform. (± 30 kg) 1 spare wheel holder under the loading platform on the right side, in the direction of travel. Tires 435/50 R 19.5, at the manufacturer's choice. One mudflap at the rear of the trailer. Manual and description on a USB stick. One mounting for a rotating beacon at the rear of the trailer. On the swan neck and at the rear panel, left and right, one mounting each for warning signs including socket. One INOX tool box transversely under the loading platform (1000x400x2500) (± 135 kg) 6 pairs of WADER container pockets in the loading area, for 1x20' container, 2 x 20' containers or 1 x 40' container; an additional locking point is provided in the extension for a 45' container. (± 90 kg) 4 pairs of WADER container locks. (± 60 kg) 10 pairs of galvanized plug-in rails approx. 100 x 50 mm, 1,000 mm high. (± 220 kg) 3 pairs of pocket rail strips, mounted transversely in the loading area, for plug-in rails 100 x 50 mm. (± 95 kg) S

Condition: new, maximum load weight: 44,000 kg, overall weight: 61,000 kg, axle configuration: 3 axles, Year of construction: 2026, Further information here: Crjdev D Abtspfx Aphjd

Condition: new, maximum load weight: 34,104 kg, overall weight: 47,000 kg, axle configuration: 2 axles, Year of construction: 2026, Further information here: Csdev D Abgjpfx Aphsrd

Condition: new, maximum load weight: 40,017 kg, overall weight: 50,960 kg, axle configuration: > 3 axles, Year of construction: 2026, Technical Description Gooseneck: Gooseneck with rear chamfer of approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). Cedpfx Aew Dl Hqspherd 30 mm hardwood flooring. Loading Platform: 5 pairs of folding external lashing rings (LC 5,000 daN). 3 pairs of folding external lashing rings (LC 10,000 daN). 1 pair of flat-mounted lashing rings at the front of the loading platform (LC 10,000 daN). Approx. 48 mm thick hardwood flooring, checker plate covering over the axles. Landing Legs: JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load). Tyres: 205/65 R17.5 tyres as per manufacturer's specification. TPMS: TPMS tyre pressure monitoring system compliant with ECE R 141. Data transmission to the tractor unit via the standardised EBS interface according to ISO 11992. To ensure correct display, the tractor unit must be capable of transmitting and displaying this data. Axles: BPW axles, two fixed axles, two self-steering axles, air-suspended, with drum brake, with lifting/lowering function. The self-steering axles can be locked electronically via reverse gear or manually using an electromagnet. Axle tools included. Brake System: WABCO brake system in accordance with EU regulations with EBS-E (4S3M) without connecting lines to the tractor unit. Electrical System: Electrical system according to EU regulations, 24 volt LED lighting by ASPÖCK-NORDIK (ASS3). All LED side marker lamps flash with the turn indicators. ASPÖCK-UNIBOX at the front connection panel with 24N, 24S & 15-pin sockets. Connections conform to ISO standards: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel Construction: Steel structure made from high-strength fine-grained steels. Steel grades: – S355J2+N/S355MC (yield strength 355 MPa) – S690QL/S700MC (yield strength 690 MPa) Paintwork: The entire steel structure is automatically shot-blasted with a turbine system after welding. A second abrasive blasting treatment with corundum ensures optimal adhesion of the coating system. HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for superior corrosion protection. Final coating with 2 coats of 2K topcoat, single-colour in a shade of your choice according to the RAL 841GL system. Rear section metallized and painted in RAL 9010 (pure white). Metallic paint not possible. Paint system tested in salt spray test according to ISO 9227-NSS. Cavities sealed with special wax. Options included: 2" kingpin One galvanized steel bulkhead. Yellow-red air couplings on the galvanized front connection panel. 2 wheel chocks with holders on the bulkhead. Fixture at the rear of the gooseneck for ALU approach ramps. Further options upon request.

Condition: new, overall weight: 49,500 kg, axle configuration: 3 axles, Year of construction: 2026, 3-Axle MULTIMAX "PLUS" semi-trailer, air-suspended and with hydraulically forced steering axles. Technical data MultiPLUS-Z-3L-UB-12AT-9.60-17.5-2.54-GR Speed: 80 km/h (legal) Total weight: 49500 kg / 31500 kg Fifth wheel load: 18000 kg Axle load: 31500 kg / 31500 kg Gooseneck length approx.: 3,900 mm Gooseneck width approx.: 2,480 mm Kingpin offset to rear approx.: 2,100 mm Fifth wheel height loaded approx.: 1205 mm Platform length approx.: 9,600 mm Extendable by approx.: ? Platform width approx.: 2,540 mm Loading height at max. load approx.: 890 mm Suspension travel approx.: -55 / +145 mm Axle spacing: 1,360 mm Total weight dependent on fifth wheel load: Yes Special permit required if exceeding country-specific regulations. Technical description Gooseneck: Gooseneck in SNT design to optimize platform length, length approx. 3,900 mm, rear with a bevel of approx. 1,000 mm x 6°. Technical fifth wheel load: 18,000 kg. For tractor-trailer combinations: 4 x 2 and 6 x 2. Platform: Platform, length approx. 9,600 mm with a bevel at the rear of approx. 900 mm x 6°. Platform behind the gooseneck can be hydraulically raised and lowered, length approx. 3,000 mm, loadable up to approx. 9,000 kg. Ramps: DR-10-900-4920-GR-HV-AXS A pair of two-piece AXS steel ramps with a length of approx. 4,920 mm and a width of approx. 900 mm. Open grating deck. Hydraulically folding ramp ends. Ramps can be individually hydraulically shifted outwards by approx. 235 mm and inwards by approx. 365 mm. Maximum load and angle of inclination according to technical data sheet: C470319 Maximum inclination angle with lowered platform: 9° Axles and suspension: BPW axles and suspension, all axles hydro-mechanically forced steered. Technical axle load: 12,000 kg Air suspension with lifting and lowering valve. Axle tool. Tires: 235/75 R 17.5 3PMSF, twin tires. Manufacturer according to our choice Load index 143/141J (144/144F) Braking system: Braking system of the brand WABCO EBS-E according to EU regulations. Without connection cable to the tractor unit. Lighting system: 24-volt lighting system in "ASPÖCK-NORDIK full LED" design according to EU regulations. (ASS 3) Metallization: Complete HRM metallization (High Resistance Metallization) Complete steel structure shot-blasted, then hot-dip galvanized with ZINACOR 850 (Zinc 85% - Aluminum 15%). Painting: 6-coat finish: Complete steel structure shot-blasted after welding. 1 coat of zinc-based primer, 1 coat of adhesion primer. Top coat with 2 coats of 2-component paint (acrylic), solid color in RAL colors of your choice, followed by sealing of the cavities with special wax. Rims in silver. Multi-color and special paint finishes available at an extra cost. Steel structure: Steel structure made of high-strength fine-grain steels. Steel qualities: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welders tested according to DIN-EN 287-1. Welding process MAG according to EN ISO 4063. Protective gas M21 according to EN ISO 14175 Front wall made of steel, plug-in, approx. 400 mm high Connection strip for supply lines to the tractor unit, mounted at the height of the outer frame profile. Credpfsizu Ntsx Aphjd ASPÖCK-UNIBOX on the connection strip at the front with sockets 24N, 24S & 15-pole. 24N connection according to ISO-1185 24S connection according to ISO-3731 15-pole connection according to ISO-12098 If your pin assignment differs from the ISO connection standard, please inform us. "Anderson" socket on the connection strip at

Condition: excellent (used), functionality: unexamined, empty load weight: 18,940 kg, maximum load weight: 71,630 kg, overall weight: 18,940 kg, axle configuration: > 3 axles, first registration: 12/1992, loading space width: 3,100 mm, suspension: hydraulics, tire size: 245/70R22.5, wheelbase: 1,360 mm, color: blue, Year of construction: 1993, operation weight: 90,300 kg, Noteboom OSBDAZ-66 90T Machinery Transport Gondola Cedpjxgh Exefx Apherd Low-bed Front loading and unloading 4 steering axles

Condition: used, axle configuration: 3 axles, first registration: 04/2015, suspension: air, tire size: 445/45/19,5, color: blue, Year of construction: 2015, Equipment: ABS, Krone mega semi-trailer 2015 cover uncover raise lower new tarpaulin Codpfx Apsqmnrxjhsrd fixed axles

Condition: new, functionality: fully functional, Year of construction: 2026, Equipment: ABS, EBS, 2+1 Axle Platform Trailer Credpfx Apeyaxthohed

Condition: new, Year of construction: 2026, We have all Europe documents! Crsdoqx Nd Rjpfx Aphod We can delivery the trailers with FOB-EXW-CPT-CFR-CIF If you have an interest please contact with us; For European Countries; For African Countries;

Condition: new, Year of construction: 2026, GVN Trailer 4 Axle Exclusive Lowbed        Please get contact with us for more informaiton;     Csdpfoqxbfmsx Aphjrd

Condition: new, Year of construction: 2026, GVN Trailer 4 Axle Extendable Lowbed     Codpfx Apjqxq Aijherd      Please get contact with us for more informaiton