Multi blade saw

CML SCA 220 T 250

Condition: new, Best price 4499 Eur (EXW Jonava, Lithuania) Dimension of sliding table- 2200x375mm Gross cut capacity- 1500mm Width of cut between saw blade and rip fence - 1140mm Saw blade diameter - 400mm Height of cut (90°) - 115mm Height of cut (45°)- 105mm Speed of main saw spindle - 4500/6000rpm Main spindle diameter - 30mm Tilting saw blade - 0-45º Saws lifting, up and down, electrical control. Main motor - 5,5 kW Scoring saw blade diameter - 120mm Speed of scoring saw blade - 7000-8000rpm Scoring saw diameter - 20mm Scoring motor - 1,1 kW Nsdsdnxydspfx Adtola Weight: 700 kg * Using the blade 400mm, the smaller should be removed. Reduced saw blade should be used with not more than 350 mm main shield.

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC Nlodpfx Ajwp Rqfodtja The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: new, Year of construction: 2024, Boring and inserting machines Rilesa Vlg 2200 new 2023 Make: Riles Model: Vlg 2200 Description: Condition: new Year: 2023 Start type: to be agreed Cost of delivery: Customer cover Conditions of delivery: OWN RECEIPT Category: Machine Tools equipment in Poland Subcategory: Drills Subcategory 2: Drilling machines Description DRILL DRILL WITH STORAGE 8 DRILLING UNITS TWO FRONT RIGHT AND LEFT, 3 UPPER AND 3 BACKS Year: 2023 new Njdpfx Aogbpmhjdtela

Year of construction: 1988, condition: repair required (used), mechanisation for planer infeed -For lengths up to ca. 13 m -Ideal unit for KVH (solid construction timber)and BSH (laminated beams) in front of the planer -1 operator -lateral destacking unit -separation Nodevbtpepfx Adtola -4 cross cut saws -cutting cross section 180x220 mm, 150x300 mm

Condition: excellent (used), Weinig four-sided planer max planing width 230mm max planing height 120mm 5 heads, bottom-5,5KW; left and right-11KW, top-11KW, bottom-5,5KW feed - 4KW fully adjustable heads electrically adjustable up and down and planing width 40mm spindles feed on gimbal rollers, with smooth adjustment Nedpfx Asrigxyedtola WEINIG brand solid planer, length of the machine 415cm machine checked in original condition

Year of construction: 1998, condition: ready for operation (used), A Construzioni Macchine Legno s.r.l. multirip saw is available. Saw blade diameter min./max.: 250mm/360mm, saw blade inner diameter min./max.: 70mm/95mm, cutting width: 320mm, cutting height movable/rigid: 90mm/120mm, weight: approx. 3000kg. On-site inspection is possible. Nljdowv Umwopfx Adtsa

Condition: good (used), Year of construction: 2020, Masterwood Project 351 L 3-Axis CNC machine Description Aircooled 3-axis milling motor 17,5HP (HSK-63F) Static frequency inverter for programming speed 1.500-24.000 t.p.m. Toolchanger with 22 positions 6 pneumatic countersinkable panel guides for loading/positioning heavy parts Prepared for install. clamps 2 horizontal clamps for beamwood 6 zero points over X-axis (positioning of panels at backside of the supports 8 zero points over X-axis (positioning of panels half-way the supports) Nodpfxjvu U Itj Adtsla Full reference at rightside over Y-axis Full reference at leftside over Y-Axis 2 workingfields 1 x 100m³ vacuumpump 24 vacuumcups Remote control with digital read-out Auto tool measuring system Transport waste belt Drill unit with 19 spindles (32mm center distance) 2,2kW - 7 vertical drillspindles in X-direction - 6 vertical drillspindles in Y-direction - 4 horizontal drillspindles in Y-direction - 2 horizontal drillspindles in X-direction (all drill spindles independently programmable) Control unit with PC SINCRO Software CAD/CAM MASTERWORK Technical specifiactions Working range in X - 5.130mm Working range in Y - 1.550mm Speed in X-Y 80 mtr./min. Speed in Z 25 mtr./min. Max. workpiece thickness 200mm Milling motor power 17,5 HP (S1) RPM milling motor 1.500 - 24.000 Drill unit 3HP Toolholdersystem HSK63-F Toolchanger 22 positions Vacuumpump 100m³ Dustextraction 250mm Aircapacity 4.500m³/h Airspeed 30 mtr./sec. Compressed air 7 bar Compressed air consumption 300-500ltr./min. Fuse value 40 Amp. Weigth 7.000kg (All changes, mistakes in technical data, info and prices reserved. Availability subject to prior sales. No guarantee on printed data!) (Alle Änderungen und Irrtümer in den technischen Daten, Angaben und Preisen sowie Zwischenverkauf vorbehalten! Keine Garantie auf gedruckte Daten!) Best woodworkingmachines from the Netherlands Holland Die besten holzbearbeitungsmaschinen aus die Niederlande De beste gebruikte machines uit Nederland

Condition: like new (used), Year of construction: 2015, functionality: fully functional, type of input current: three-phase, power: 45 kW (61.18 HP), input voltage: 400 V, For sale Spanner Biomass cogenerator station with 9 units. Model - BHKW45-8,0-V1.1 Year - 2015-2017 Nominal power - 6x45KW, 3X50KW Voltage - 400V Frequency - 50HZ Current - 3 phase Engine - 8.0L Price shown per unit. Nlodevcbtrjpfx Adtsa 1 unit includes: Biomass gasifier, generator that converts the gas with engine to electricity, separate control cabinets for gasifier and generator. Price is discussable. Please see attached documents. Preferred text communication via e-mail or whatsapp.

Year of construction: 1998, condition: excellent (used), I sell the window production set: 1pc. tenoning profiling centre Weinig Unitec 10 1pc. profiling automat centre Weinig Univar 10 Nlodpfofzzhyox Adtja Year 1998. Moulding heads OERTLI. Available immediately. Total price 17.000 euro. Condition very good !

Condition: like new (used), The MSP 120 ZK is ideally suited for crushing and subsequent briquetting of various types of metal chips. The MSP 120 ZK briquetting press with integrated shredder is composed of a hydraulic chip press paired with an upstream shredder, both perfectly matched to each other. This system enables the crushing and compaction of chips generated during turning and milling operations. The volume is significantly reduced, and the briquettes are separated from the coolant lubricants (emulsion, oil) absorbed during earlier machining processes. The system consists of a feed hopper for loading the material to be processed and a shredder inside the hopper, which reduces chip length. A conveyor system moves the shredded chips continuously and stepwise via a conveyor belt into the chip press hopper. There, two augers feed the material into the compaction chamber. The system is equipped with a monitored liquid collection tank and pump, allowing coolants to be returned to the production process. Cycle control is managed by a PLC and an electronic level sensor for the monitoring of the hopper fill level. Optionally, a tipping device can be added for manual loading of the unit. Briquetting Press: Throughput (Aluminum): 15–20 kg/h Throughput (Steel, Copper): 45–60 kg/h Briquette diameter: 60 mm Productivity: 120–180 pcs/h Specific pressure on briquette: 1,050 kg/cm³ Motor pump power: 7 kW Total installed power: 10 kW Voltage: 400V / 50 Hz Oil tank: 80 l Dimensions: 1,400 x 1,200 x 1,050 mm Weight: 800 kg Nljdjw R Ranopfx Adtoa Shredder: Number of knife shafts: 1 pc Motor power: 5.5 kW Number of knives: 16 pcs Exchangeable knives: Yes Knife size: 25 mm Knife material: Hardened steel Shaft length: 400 mm Screen mesh size: 20 mm Hopper inner diameter: 1,000 mm Hopper volume: 1 m³ Weight: 280 kg Power supply: 380V Overall system dimensions: 2,820 x 1,862 x 2,065 mm Colour: Textured paint, RAL 7035 light grey