Pellet press

CPM 7930-4

Condition: new, Best price 4499 Eur (EXW Jonava, Lithuania) Dimension of sliding table- 2200x375mm Gross cut capacity- 1500mm Width of cut between saw blade and rip fence - 1140mm Saw blade diameter - 400mm Height of cut (90°) - 115mm Height of cut (45°)- 105mm Speed of main saw spindle - 4500/6000rpm Main spindle diameter - 30mm Tilting saw blade - 0-45º Saws lifting, up and down, electrical control. Main motor - 5,5 kW Scoring saw blade diameter - 120mm Speed of scoring saw blade - 7000-8000rpm Scoring saw diameter - 20mm Nedpfx Asdnxydedtela Scoring motor - 1,1 kW Weight: 700 kg * Using the blade 400mm, the smaller should be removed. Reduced saw blade should be used with not more than 350 mm main shield.

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC Nsdjwp Rqfepfx Adtsla • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Year of construction: 2026, condition: new, functionality: fully functional, Complete plastics recycling line for films and fibre materials from Taiwan leading Plastics Recycling Machinery manufacturer. GENIUS Machinery Co who have more than 30 years of recycling extruder production and experience. Extruder can be fed without size reduction or shredding.. Materials in baled, loose or reel form can be fed. Line can be supplied complete with Belt conveyor, Cutter compactor, Main extruder, Filtration system, (variety of types to suit requirements), Hot pellet die-face cutting device, Centrifugal pellet dryer, Vibrating screener, Storage silo for pellets. Additional ancillary equipment can be supplied . A two stage " Cascade" version is also available for heavily printed films, or very dirty films requiring double filtration. Alternative sizes from 100 kgs per hr up to 1200 kgs per hr can be offered. Full sales and support and training is available in UK and Europe for these extremely modern and economic machines. Nljdpfxswg R Rtj Adtsa

Condition: excellent (used), Year of construction: 2021, functionality: fully functional, Cheese vat / Pasteurizer / Process tank 100 liters. Used - 3.5 years old The Vat: - Completely stainless steel - Double jacket (bain-marie) + insulation - Must be operated without pressure - 100 liters - Butterfly valve, NW 50 - Agitator mounted on the lid and easily removed using a quick-change adapter. - Agitator rotates slowly; approximately 24 RPM - 400 volt / 8.4 kW heating (16 amp plug). Heating power can be halved with a switch (8.4 - 4.2 kW). Nedpjwg Ellefx Adtsla Control: - Digital milk temperature display - PID controller / thermostat - Control system with one automatic program (heating - holding - cooling) and manual operation (manual heating and manual cooling with cold water) - Heats up to 90°C - Cooling with cold water. Water inlet with motor-controlled ball valve.

Condition: good (used), Year of construction: 2007, functionality: fully functional, Pellet production line based on Italian producer Zepi pellet press, hammer mill, pellet cooler and sifter. Machines are really powerful and reliable. Some parts like hammer mill are completely refurbished. Year of production 2007. Nedpfovx S Ryjx Adtsla

Condition: refurbished (used), Dry board sorting line - dry board sorting line Nodevzqcyjpfx Adtela - 20 pockets - belt - automatic spacer collection - Trimmer Almab with 16 saw blades - automation- TG automation, Sweden Sorting - Dynalyse MC Pro 2400 System - marking/printer - Alpha Dot Merlyn 350 - Drum chipper Erjo 204 MA - stacker Almab with 9 cassettes - Pack press

Condition: used, Year of construction: 1998, machine/vehicle number: 100057, 1998 AMADA VIPROS 2510 KING The punching machine is in good condition, always serviced on time by Amada service. All documentation is included. This machine can be operated with a punching force of 196 kN. Made in Japan. The punching machine is still under power and can be tested at any time in Vilnius, Lithuania. Specification: Model: AMADA VIPROS 2510K Serial no: 100057 Year: 1998 Made in: Japan Punching force: 20 tons Stations: 31 Tools: included (RO 6; RO 6,5; RO 3; RE 30x5; RE 25x5; RE 80x5; RO 5; RO 3,5; RE 10x3; RE 10x5; RE 50x5; RE 8x12) Maximum sheet thickness: 3 mm Nodpfx Asm Ncayedtjla X-axis movement: 2500 mm Y axis travel: 1270 mm Weight: 11 000 kg Location: Vilnius, Lithuania Testable: Yes If you have any questions, please do not hesitate to contact us.

Condition: good (used), the machine is in good condition, includes electrical cabinets, sharpening machine Nljdjvdyr Nspfx Adtoa

Year of construction: 2008, condition: excellent (used), SMG HZPU 8000-3000/2100-S1 Hydraulic Drawing Press Brand SMG Type HZPU 8000-3000/2100-S1 Year 1995 Description Hydraulic Drawing Press H frame hydraulic press Pressing force 800 ton Clamping area Approx. 3,000 x 2,100 mm Installation height Max. 1,400 mm Nlsdjn Awd Rspfx Adtoa

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: SF100s.01.26, screw diameter: 200 mm, total length: 3,200 mm, total height: 2,200 mm, overall weight: 400 kg, heating capacity: 10 kW (13.60 HP), pressure: 2 bar, type of input current: three-phase, input frequency: 50 Hz, input voltage: 380 V, warranty duration: 24 months, Machine for cheese streching, dozing, mozarella and other. Nedpfx Adjt I Dxwjtola