Angle roll shaft diameter 130 mm

FACCIN RCMI 130

Condition: excellent (used), Year of construction: 2013, controller manufacturer: ELFRAN Digital Read Out, number of rollers: 3, shaft diameter: 130 mm, overall weight: 5,800 kg, total length: 2,200 mm, total width: 2,400 mm, total height: 2,000 mm, Profile bending machine FACCIN - RCMI 130 MACH-ID 9451 Make: FACCIN Gusdpfoyrq Dvsx Aqiof Type: RCMI 130 Control: ELFRAN Digital Read Out Year: 2013 3 rolls driven 2 lateral guide rolls Digital readout for position rolls Set hardned universal rolls Set hardned profile rolls Horizontal and vertical:|Horizontal and Vertical Shaft Ø: 130mm Number of rolls: 3 Capacity flat: 240 x 30 x 1000mm Capacity Tube: 140 x 5 x 1500Ø x mm Capacity bar: 80 x 80 x 900mm Capacity T-Profile: 140 x 15 x 1400mm Capacity HEA-Profile: 160 x 1700mm Working speed: 0 - 6000mm/min. Side supports: 2 x Hydraulic side arms Length: 2200mm Width: 2400mm Height: 2000mm Weight: 5800kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Year of construction: 1992, sheet width 2050 mm plate thickness 10.0 mm ST pre-bending 8.0 mm ST diameter of upper rolls ~ 205 mm side roll diameter ~ 195 mm Control konv. oil volume 80.0 Liter voltage 380 V total power requirement 5.5 kW weight 3200 kg range L-W-H 4500 x 1500 x 1300 mm Features: - Robust electro-hydraulic 3-roll bending machine - 3-roll concept offers a wide range of bending and rounding options - Pivoting control unit at the front * Operation - Control of all rolls and machine axes * Digital position display * Manual operation via joysticks - Diameters of up to 1.1 times the top roll diameter are possible - Forged and hardened rolls with a hardness of 53-55 HRC - Low-maintenance, stable machine design - Sturdy welded steel construction - Electro-hydraulic folding bearing for easy pipe removal - Pressure gauge / pressure indicator for the rolls - Safety device (safety lanyard with switch unit) - Operating instructions (PDF) Gedpfoxacdvex Aqieuf

Condition: new, functionality: fully functional, power: 5.7 kW (7.75 HP), gearing type: hydrostat, color: green, overall weight: 1,995 kg, lifting power: 2,820 kg/m, lifting height: 8,700 mm, tire size: Rubber tracks, tire condition: 100 %, Year of construction: 2021, operating hours: 2 h, Equipment: additional headlights, hydraulics, onboard computer, === KEY SPECIFICATIONS === Year of manufacture: 2021 Operating hours: 2 h Max. lifting capacity: 2,820 kg Max. lifting height: 8.7 m Jib reach: 8.205 m Drive: Fully electric (lithium-ion battery) Remote control: Yes (wireless radio remote control) Jib: Included Attachments / extra equipment: Searcher hook, multi-position outriggers, programmable moment limiter Tyre type: Rubber tracks Track condition: Excellent / like new Weight: 1,995 kg CE certification: Yes === HIGHLIGHTS === Carefully selected from reliable sources with verifiable history CE certification and full documentation included Ready for immediate transport and operation Extensive technical documentation available Fully electric zero-emission spider crane Lithium-ion battery with fast charging Continuous operation while charging Compact and lightweight design Godpfoyidbmjx Aqiouf Multi-position outriggers Wireless remote control Eco working modes === CONDITION === Excellent working condition (new) – fully inspected, serviced and tested by certified professionals. Inspection available upon request. === LOCATION & PRICE === Located in Sittard, the Netherlands. Worldwide delivery available. Price €81,500 (EXW / excl. VAT). Reliable machines from first owner with full service history and professional technical support. Benefit from one of the largest European stocks of new and used machines. All machines are fully inspected, CE certified and ready for immediate use. Spare parts and professional assistance available upon request. === DELIVERY === Crane loading available on request for smooth transport during shipment. Flexible shipping options tailored to your destination and logistical preferences. All transports are professionally handled by the Collé Rental & Sales logistics team.

Condition: excellent (used), Year of construction: 2001, turning length: 8,000 mm, turning diameter over bed slide: 2,000 mm, workpiece weight (max.): 25,000 kg, turning diameter over top slide: 1,550 mm, Swing over bed Ø: 2000mm Swing over cross slide Ø:1550mm DBC Turning Length: 8000mm Spindle bore: 150mm Spindle power: 95kW Bed width: 1400mm Tailstock spindle Ø: 260Ø Stroke pinole: 200mm Spindle taper: Metric 80Mk Godpfxexxxbzo Aqieuf Workpiece weight: 25000 Power: 95A Speeds / ranges: 360Rpm Feed rate X-Axis: 0 - 6000mm/min. Feed rate Z-Axis: 0 - 6000mm/min. Length: 16000mm Width: 5000mm Height: 3800mm Weight: 80000kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: new, Year of construction: 2025, functionality: fully functional, The CNC BAYKAL Hybrid Press Brakes combines all the benefits of both hydraulic and all-electric press brake systems into one. If you’re looking for press brakes that are fast, accurate, and energy-efficient, BAYKAL is the way to go. The CNC BAYKAL Hybrid Press Brakes can significantly save energy, save fuel, improve bending efficiency, reduce the risk of oil leakage, reduce installation costs, extend the service life of consumables, improve bending accuracy, reduce noise, and improve the working environment. The CNC BAYKAL hybrid press brakes system are designed with an individual electro-hydraulic servo drive system and servo pumps to control the for each of the left and right cylinders. The servo motor controls the output flow of the oil pump according to the program setting, and then controls the movement speed and position positioning of the slider, and there is no throttling phenomenon in the whole process. Therefore, all the energy output by the oil pump is supplied to the left-right oil cylinder. This control method does not have any energy loss, and the energy-saving effect is very prominent. With this system the hydraulics run on demand when the foot pedal is activated, rather than having a pump running continuously. This results in lower energy usage than a standard hydraulic machine as well as faster cycle times and extremely high accuracy. The flow and pressure of Y1 and Y2 oil cylinders are respectively controlled by two sets of servo bidirectional pump systems, and the oil in the upper chamber of the oil cylinder is directly pumped into the lower chamber of the oil cylinder through the oil pump to realize the lifting of the beam. Godpfsrq D Nijx Aqiouf The reverse rotation of the oil pump pumps the oil in the lower chamber of the oil cylinder directly into the lower chamber of the oil cylinder to realize the pressing and bending of the upper die. Applicable between from 100 Tons to 1250 Tons, the synchronization of the left and right of the upper beam of the CNC BAYKAL hybrid press brakes is controlled separately by two sets of servo bidirectional pumps.

Condition: used, Year of construction: 2016, operating hours: 1,476 h, functionality: fully functional, Hello, we are offering a Hurco VM 30 i Plus for sale here. Travel: X-axis: 1270 mm Y-axis: 510 mm Z-axis: 510 mm Control: Max5 Gsdpfxeyhw Eaj Aqisuf Taper: SK-A40 Max spindle speed: 12,000 rpm Transport weight: 4,550 kg If interested, please call. Sale on behalf of customer.

Condition: new, sheet width 1550 mm plate thickness 6.5 mm pre-bending 4.5 mm diameter of upper rolls 150 mm side roll diameter 130 mm diameter of lower rolls 150 mm distance max. OW zu UW 20,0 mm total power requirement 2.2 + 1.5 kW weight of the machine ca. 2370 kg. range L-W-H 3300 x 1150 x 1110 mm Exhibition machine - NEW not yet in use (!!) Special price on request Equipment: - electro-hydraulic 4-roller round bending machine * with driven top roller + bottom roller * stable welded construction - Area of application: Godjxabkbspfx Aqieuf * light to heavy sheet metal processing (steel/aluminum/stainless steel) - electro-hydraulic adjustment of the bottom + side rollers - linear guidance of the side rollers - top roller driven by robust electric motor + planetary gear - freely movable, separate control panel - hardened rollers SAE 1050 (CK 45) + crowning - conical bending device - 3x axis digital display for precise roller positions - electro-hydraulic folding bearing - operating instructions (PDF)

Condition: new, functionality: fully functional, Year of construction: 2026, roller (bottom) diameter: 310 mm, roller (top) diameter: 320 mm, roller diameter: 310 mm, roller length: 1,550 mm, working width: 1,500 mm, sheet thickness steel (max.): 38 mm, overall weight: 12,500 kg, total length: 4,500 mm, total width: 2,300 mm, total height: 1,740 mm, power: 18.39 kW (25.00 HP), working length: 1,500 mm, Equipment: documentation/manual, emergency stop, FACCIN HAV 15342 variable three-roll bending machine Electronically controlled, hydraulic three-roll bending machine Technical data: Number of rollers: Three Geometry of the side rollers: variable Working width: 1550 mm Top roller diameter: 320 mm Side roller diameter: 310 mm Pressure force against the top roller: 160 tons Working pressure at nominal force: 250 bar Guaranteed installed power: 18 kW (25 hp) Guaranteed maximum rotation speed: 3.5-7 m/min Guaranteed machine weight: 12,500 kg Length: 4,500 mm Width: 2,300 mm Height: 1,700 mm Guaranteed performance: for material with yield strength 260 N/mm² Rolling capacity (full working width) 38 mm Bending capacity (full working width) 20 mm from pipe diameter 1,600 mm Rolling capacity (full working width) 30 mm Bending capacity (full working width) 17 mm from pipe diameter 415 mm Standard equipment: Gedpfet Akt Rsx Aqiouf Variable geometry with linear guides for roller movement Extra long folding bearing for increased frame stability Electronic parallelism system EPS Hardened rollers for high wear protection All rollers ground after heat treatment Siemens S7-HMI PLC control system PGS-CLASSIC control system with Siemens touch panel Hitech hydraulic and electrical package Simultaneous rotation and roller movement Safety ripcord with emergency stop and CE certification Central lubrication Water cooling for the hydraulics Cone bending device Prepared for retrofitting of supports and roller conveyors FACCIN Advantage Package AP

Condition: used, Year of construction: 1997, The bending press was manufactured in 1997 in England by EDWARDS PEARSON. The folding press is in good condition, sold with tools. Always serviced and maintained on time. The machine tools are connected and can be tested and inspected. Specification: Gedpfx Aorfx Utsqisuf Model: EDWARDS PEARSON 100/3100 PR6 Year: 1997 Working length: 3 100 mm Bending capacity: 100 T Travel: 172 mm Distance between table and frame: 450 mm Working speed: 100 mm/s Return speed: 110 mm/s Axes: auto X1, X2, Y1, Y2, Z1 , Z2 , R Tools: Available Weight: 7 T Other: New screen recently replaced, keyboard attached for ease of use. If you have more questions, we will be happy to answer.

Condition: used, material width 300 mm coil weight 3 t material thickness 2 - 4 mm Straightener, 7 rolls, Make. Schleicher, Type RM 6-95/160 - band width 300 mm - band thickness 2 – 4 mm - cross cut 1200 mm² - voltage 220/380 V 50 Hz - total power requirement 3,1 kW coiler with press roll, Make Schleicher, Type H-3 - Coil weight 3 t Gjdpocdrmmsfx Aqieuf - Band width 400 mm - voltage 220/380 V 50 Hz - total power requirement 3,92 kW without control