Single-column eccentric press

HELMERDING EH 25 B

Condition: good (used), Make: OMERA Type: R4 / 12-2 Year: 1976 Table length : 1900 Table width : 1000 Steady arm throath HOR : 670 Steady arm throath VER: 940 Stroke cylinder : 350 Column diameter : 200 Specifications Metric US Standard There are no specifications for this machine (yet). Dimensions (Estimate) Length Podpfxjkvnume Adljgk 3000 mm Width 2200 mm Height 2500 mm Weight 2800 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: as good as new (ex-display), Year of construction: 2021, machine/vehicle number: 06 61 218, Comm. no.: Lg 32821 Single side decoiler BBT ABH 2000/400 exhibition machine, unused machine no.: 06 62 218 year of manufacture: 2021 Technical data load capacity approx. max. 2.000 kg strip width max. 400 mm Coil inner diameter approx. 450 to 520 mm Coil outer diameter max. 1,500 mm Unwinding speed approx. 2 to 15 min.-1 With adjustable drive and loop control via ultrasonic sensor (analog). Drive by frequency-controlled three-phase geared motor. Spreading of the support segments manually by means of hand crank via joints Number of supporting segments 3 Coil side guide via strong limiting arms, clampable. Reel stand in strong box construction as welded design. construction. Additional equipment: Pedsg U Utvepfx Adlsgk Shutdown "belt loop too small" by antenna switch, attached to the column of the bottom housing of the loop control. Infinitely adjustable in height. Tape side guide at the bottom housing of the loop control, by means of lateral guide rods. The passage width is continuously adjustable.

Year of construction: 2012, condition: excellent (used), Description to follow! Psdpfjx A H Rxex Adlsgk

Condition: used, Eccentric punch press HAULICK + ROOS type RVD 125 double column - eccentric press Machine No. 212560 Year of construction 1981 pressure force 125 ton. table size 880 x 800 mm table opening 470 x 140 mm column width 900 mm column width lateral 415 mm ram stroke 45 mm slide adjustment travel 0-80 mm Installation height on the picture 340 mm Stroke rate 50 to 300 strokes/min. Motor power main drive 22 kW Mains connection 380 volt, 50 Hz - Double connecting rod drive with 4-fold eccentric shaft for off-center ram pressure load Podohlnzkspfx Adlogk - adjacent electrical cabinet - NC roll feed EBU, width 250 mm, year 2003 - adjacent control panel for roll feed - strip running direction from left to right space requirement (press) L x W x H 3000 x 2000 x 3020 mm transport height 2950 mm weight of the press approx. 11 ton.

Condition: excellent (used), functionality: fully functional, Year of construction: 1984, Loading capacity: max. 300 Kg. Diameter of decoiler: 1.000 mm Diameter of spool: max. 900 mm Inside diam of spool: 240 - 560 mm Hight of spool: max. 180 mm Pgodpef S I I Hjfx Adljk

Year of construction: 1987, condition: used, sheet width 150 mm coil weight 80 kg coil external diameter 650 mm 1000 mm diameter of the mandrel 230 - 445 mm total power requirement kW weight of the machine ca. t dimensions of the machine ca. m Pgjdpfxsfn Aqlo Adlsk

Condition: used, Year of construction: 1970, machine/vehicle number: 120895, pressure:63 t throat:250 mm stroke:8 - 100 mm no. of strokes:120 Hub/min table::715 x 500 mm dayligth:330 mm ram adjustment:63 mm clamping plate:700 x 480 mm hole in the table:240 mm Hole in clamping plate:110 mm dimension of ram:450 x 280 mm Pgjdjfx Hv Hjpfx Adlok weight of the machine ca.:5,5 t dimensions of the machine ca.:1,2 x 1,7 x 2,7 m hydraulic tilting single column eccentric press, tilting in 4 steps, opening to rear (325 x 500mm) and below (360x160mm) with central lubrication via hand pump, additional clamping plate 700 x 480 x 850 mm, two-hand operation, foot-trip operation possible, operating-mode selector for adjustment of continuous or single stroke, emergency cut-off, piece counter, various accessories

Condition: used, material width 300 mm coil weight 3 t material thickness 2 - 4 mm Podjcdrmmjpfx Adlsgk Straightener, 7 rolls, Make. Schleicher, Type RM 6-95/160 - band width 300 mm - band thickness 2 – 4 mm - cross cut 1200 mm² - voltage 220/380 V 50 Hz - total power requirement 3,1 kW coiler with press roll, Make Schleicher, Type H-3 - Coil weight 3 t - Band width 400 mm - voltage 220/380 V 50 Hz - total power requirement 3,92 kW without control

Condition: used, Year of construction: 2009, pressure 40 t stroke 4 - 100 mm no. of strokes 130 /min throat 230 mm dayligth 475 mm table surface area 650 x 460 mm hole in the table 205 x 165 mm Pgsdpfx Ajvzxpnedlok table height over floor 710 - 950 mm table adjustable 240 mm ram surface 435 x 240 mm ram adjustment 85 mm power requirement 5,0 kW Weight 2,6 t dimensions of the machine ca. 1,2 x 1,7 x 2,3 m x m x m permitted for manual loading according to the CE-norm with motor, pneumatic hydraulic clutch/brake combination, mechanical overload protection in ram, manual stroke adjustment, manual ram adjustment, motoric centralized lubrication, adjustable table, two-hand and foot operation

Condition: as good as new (ex-display), Year of construction: 2008, machine/vehicle number: LSP 100T, Productions-Hydraulic press with H-column 100t with guidance Pgodpfog Rn Efex Adlok Manufacturer: Stenhoj Denmark Year of construction: 2008 Pressure force max. 1,000 kN / 318bar Press cylinder, stroke length: 400mm Press table with T-slot 1,500x900mm above 1,500x1,050mm below Stand passage 1,700mm Condition as good as new, the machine was only used for test runs and has been in stock since then. All statements without guarantee. Without transport costs.