Section bending roll shafts 360 mm

MG AR360

Condition: new, Year of construction: 2025, functionality: fully functional, The CNC BAYKAL Hybrid Press Brakes combines all the benefits of both hydraulic and all-electric press brake systems into one. If you’re looking for press brakes that are fast, accurate, and energy-efficient, BAYKAL is the way to go. Dwsdjrq D Nispfx Anzja The CNC BAYKAL Hybrid Press Brakes can significantly save energy, save fuel, improve bending efficiency, reduce the risk of oil leakage, reduce installation costs, extend the service life of consumables, improve bending accuracy, reduce noise, and improve the working environment. The CNC BAYKAL hybrid press brakes system are designed with an individual electro-hydraulic servo drive system and servo pumps to control the for each of the left and right cylinders. The servo motor controls the output flow of the oil pump according to the program setting, and then controls the movement speed and position positioning of the slider, and there is no throttling phenomenon in the whole process. Therefore, all the energy output by the oil pump is supplied to the left-right oil cylinder. This control method does not have any energy loss, and the energy-saving effect is very prominent. With this system the hydraulics run on demand when the foot pedal is activated, rather than having a pump running continuously. This results in lower energy usage than a standard hydraulic machine as well as faster cycle times and extremely high accuracy. The flow and pressure of Y1 and Y2 oil cylinders are respectively controlled by two sets of servo bidirectional pump systems, and the oil in the upper chamber of the oil cylinder is directly pumped into the lower chamber of the oil cylinder through the oil pump to realize the lifting of the beam. The reverse rotation of the oil pump pumps the oil in the lower chamber of the oil cylinder directly into the lower chamber of the oil cylinder to realize the pressing and bending of the upper die. Applicable between from 100 Tons to 1250 Tons, the synchronization of the left and right of the upper beam of the CNC BAYKAL hybrid press brakes is controlled separately by two sets of servo bidirectional pumps.

Condition: used, Year of construction: 1997, The bending press was manufactured in 1997 in England by EDWARDS PEARSON. The folding press is in good condition, sold with tools. Always serviced and maintained on time. The machine tools are connected and can be tested and inspected. Specification: Model: EDWARDS PEARSON 100/3100 PR6 Year: 1997 Working length: 3 100 mm Bending capacity: 100 T Dwodpfsrfx Utox Anzoa Travel: 172 mm Distance between table and frame: 450 mm Working speed: 100 mm/s Return speed: 110 mm/s Axes: auto X1, X2, Y1, Y2, Z1 , Z2 , R Tools: Available Weight: 7 T Other: New screen recently replaced, keyboard attached for ease of use. If you have more questions, we will be happy to answer.

Condition: used, material width 300 mm coil weight 3 t Dedpfxecdrmmo Anzswa material thickness 2 - 4 mm Straightener, 7 rolls, Make. Schleicher, Type RM 6-95/160 - band width 300 mm - band thickness 2 – 4 mm - cross cut 1200 mm² - voltage 220/380 V 50 Hz - total power requirement 3,1 kW coiler with press roll, Make Schleicher, Type H-3 - Coil weight 3 t - Band width 400 mm - voltage 220/380 V 50 Hz - total power requirement 3,92 kW without control

Condition: used, Year of construction: 1957, turning diameter over bed 800 mm turning diameter over slide rest 540 mm turning length 4000 mm centre height 400 mm Dedpfxexwp Ehs Anzowa centre distance 4000 mm spindle turning speed range 9 - 1140 U/min spindle passage 96 mm weight of the machine ca. 8,5 t dimensions of machine L x W x H 7,0 x 1,70 x 1,70 m - with gap with insert - Accessories: 3-jaw chuck FORKARDT 400 mmø, 4-jaw chuck 500 mmø, faceplate 800 mmø, DRO on X-and Z-axis ACU-RITE, MULTIFIX-head with various inserts, 2 solid steadies, 1 running steady, running center, coolant

Condition: used, Year of construction: 1992, sheet width 2050 mm plate thickness 10.0 mm ST pre-bending 8.0 mm ST diameter of upper rolls ~ 205 mm side roll diameter ~ 195 mm Control konv. oil volume 80.0 Liter voltage 380 V total power requirement 5.5 kW weight 3200 kg range L-W-H 4500 x 1500 x 1300 mm Features: - Robust electro-hydraulic 3-roll bending machine - 3-roll concept offers a wide range of bending and rounding options - Pivoting control unit at the front * Operation - Control of all rolls and machine axes * Digital position display * Manual operation via joysticks - Diameters of up to 1.1 times the top roll diameter are possible - Forged and hardened rolls with a hardness of 53-55 HRC - Low-maintenance, stable machine design - Sturdy welded steel construction - Electro-hydraulic folding bearing for easy pipe removal - Pressure gauge / pressure indicator for the rolls - Safety device (safety lanyard with switch unit) Dedpsxacdvefx Anzewa - Operating instructions (PDF)

Condition: as good as new (ex-display), MIG/MAG welding machine with inverter technology. Three-phase power supply, welding machine. Master Software TERRA PME included. Technical data Power Supply: Voltage (50/60 Hz): 3x400V ±15% Maximum input power: 22.9 kVA Maximum input current: 31.1 A Power factor PF: 0.73 Efficiency: 89% Slow-blow fuse: 25 A Open-circuit voltage: 61Vdc IP protection class: IP23S Insulation class: H Power cable: 4x3mm² – 5 m Welding: Setting range: 3–400A Duty cycle MIG/MAG at 40°C: 40% – 400A, 100% – 330A Duty cycle MIG/MAG at 25°C: 100% – 400A Wire diameter: 1.0–1.2 mm (optional 0.6–1.6 mm) Flux-cored wire diameter: 0.9–2.4 mm Aluminum wire diameter: 0.8–1.6 mm Wire feed speed: 0.5–22.0 m/min Wire spool diameter: Ø 200/300 mm Dsdpfx Ajw Rm Sasnzewa Remote control connection: yes

Condition: new, functionality: fully functional, Year of construction: 2026, roller (bottom) diameter: 310 mm, roller (top) diameter: 320 mm, roller diameter: 310 mm, roller length: 1,550 mm, working width: 1,500 mm, sheet thickness steel (max.): 38 mm, overall weight: 12,500 kg, total length: 4,500 mm, total width: 2,300 mm, total height: 1,740 mm, power: 18.39 kW (25.00 HP), working length: 1,500 mm, Equipment: documentation/manual, emergency stop, FACCIN HAV 15342 variable three-roll bending machine Electronically controlled, hydraulic three-roll bending machine Technical data: Number of rollers: Three Geometry of the side rollers: variable Working width: 1550 mm Top roller diameter: 320 mm Side roller diameter: 310 mm Pressure force against the top roller: 160 tons Working pressure at nominal force: 250 bar Guaranteed installed power: 18 kW (25 hp) Guaranteed maximum rotation speed: 3.5-7 m/min Guaranteed machine weight: 12,500 kg Length: 4,500 mm Width: 2,300 mm Height: 1,700 mm Dwedpfx Aot Akt Ronzea Guaranteed performance: for material with yield strength 260 N/mm² Rolling capacity (full working width) 38 mm Bending capacity (full working width) 20 mm from pipe diameter 1,600 mm Rolling capacity (full working width) 30 mm Bending capacity (full working width) 17 mm from pipe diameter 415 mm Standard equipment: Variable geometry with linear guides for roller movement Extra long folding bearing for increased frame stability Electronic parallelism system EPS Hardened rollers for high wear protection All rollers ground after heat treatment Siemens S7-HMI PLC control system PGS-CLASSIC control system with Siemens touch panel Hitech hydraulic and electrical package Simultaneous rotation and roller movement Safety ripcord with emergency stop and CE certification Central lubrication Water cooling for the hydraulics Cone bending device Prepared for retrofitting of supports and roller conveyors FACCIN Advantage Package AP

Year of construction: 2007, condition: ready for operation (used), A CNC profile drilling machine Voortman with a movable drilling cabin is available. Working height range: 30mm-1050mm, positioning speed: 40m/min, table width: 300mm, max. working width: 1800mm, support depth: 1500mm, tool stations: 5, max. travel speed: 40m/min, tool holder: SK40, drilling diameter range: 5mm-40mm, thread cutting range: M6-M30, working length: 16200mm. Documentation available. On-site inspection possible. Dsdpfx Anjxp Rb Iezowa

Condition: used, Year of construction: 2014, total length: 1,500 mm, total width: 1,150 mm, total height: 2,400 mm, Weight: 3.600 kg - Year: 2014 - Documentation available: Yes - CE marking present: Yes - CE certificate present: No - Serial number: 441 - Power [kW]: 3.0 - Press force [ton]: 28 - Max. working width [mm]: 1000 - Column gap [mm]: 950 - Throat depth [mm]: 220 - Backgauge depth [mm]: 415 - Transport dimensions: 1500mm x 1150mm x 2400mm (l x w x h) - Transport weight [kg]: 3600kg Dwodpfjxapftex Anzsa - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: excellent (used), I sell plasma cutter hypertherm powermax 800 d very good condition. /////Price listed for 1 pc ///// Plasma cutter Hypertherm Powermax 800 Dwsdpfx Ansulc Ixjzea Plasma cutter description The Powermax800 plasma cutting system uses an inverter power supply to provide a smooth DC output voltage for superior cutting and gouging of mild steel, stainless steel, aluminum and other metals. The Powermax800's power supply provides a constant output current that varies from 20 to 50 amps, providing optimal performance for all metal thicknesses up to 1/2 inch (12 mm). At 50 amps, the Powermax800 can cut metals up to 3/4 inch (20 mm) thick and cut metals up to 1 inch (25 mm) thick.