Used Channel for sale (846)

Condition: good (used), Year of construction: 2010, operating hours: 3,641 h, functionality: fully functional, pressing force: 36 t, filling opening width: 1,100 mm, filling opening length: 1,080 mm, bale width: 1,100 mm, bale height: 750 mm, power: 15 kW (20.39 HP), volume flow: 90 m³/h, Technical data baler: Manufacturer Presto GmbH & Co. KG Typ CC 36 M Year of construction 2010 Hours of operation 3,641 h Press power main press 36 t Specific press capacity 467 N/cm² Feed channel 1.080 x 1100 mm (l x w) Cycle time 34 sec. Capacity per cycle time 0,85 m³ Theoretic throughput rate 90 m³/h Throughput rate under operating conditions with a material bulk density of 35 kg/m³ approx. 51 m³/hour Bale size 1100 x 750 mm (w x h), length variable Driving motor 15 kW Tying 4-fold vertical, semi-automatic, with polyester synthetic yarn Throughput rate at a bulk weight of 35 kg/cbm 1,8 to/h bulk weight of 60 kg/cbm 2,5 to/h bulk weight of 100 kg/cbm 3,1 to/h Transport dimensions only baler 4.200 x 1.640 x 2.200 mm Machine weight baler approx. 4 to Comments: The press was checked for function in our workshop, then stored and is therefore available at short notice. The machine documentation (operating instructions, CE, electrical and hydraulic circuit diagram) is available. Cgedpfx Anju Thh Eo Nou Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, year of last overhaul: 2025, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Csdpevf E Avefx An Njgu Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: used, This listing is for 1 of 2 Cole Parmer MasterFlex L/S 7554-95 Peristaltic Pump with a Masterflex Easy-Load 3 pump head . The unit is in full working condition and is ready for immediate release. The Cole-Parmer MasterFlex L/S 7554-95 Peristaltic Pump is a versatile and reliable solution for accurate fluid transfer in laboratory, pharmaceutical, and industrial environments. Designed to handle a wide range of flow rates and fluid viscosities, this peristaltic pump offers precision, ease of use, and durability. Key Features: Flow Rate: Delivers flow rates from 0.6 to 3400 mL/min, adjustable based on the tubing size used. Variable Speed Control: The pump operates at speeds between 6 and 600 RPM, allowing precise control of flow. Reversible Pumping: Enables bi-directional flow for easy priming, purging, and efficient fluid transfer. Digital Display: Provides a clear, easy-to-read display showing speed, direction, and operational status for precise monitoring. Easy Maintenance: Tool-free tubing changes and a low-maintenance design for efficient operation. Compatibility: Works with a variety of MasterFlex L/S tubing, ensuring adaptability for different fluid handling needs. Durable Construction: Engineered for reliable, long-term use, with corrosion-resistant materials to withstand demanding applications. Specifications: Flow Rate Range: 0.6 to 3400 mL/min Speed Range: 6 to 600 RPM Power Requirements: 90-260 VAC, 50/60 Hz Cgsdpfx Asxv A Sxon Nju Operating Temperature: 0 to 40°C (32 to 104°F) Dimensions: 8.6" H x 9.4" W x 11.1" D (21.8 cm x 23.9 cm x 28.2 cm) Weight: 15 lbs (6.8 kg) The Masterflex Easy-Load 3 pump head is designed for user-friendly operation and fast tubing changes. Key features include: Automatic Retention Mechanism: The spring-loaded occlusion lever opens the occlusion bed and retracts the tubing retainers, allowing tubing to be easily loaded and unloaded. Tubing Range: Suitable for use with Masterflex L/S Precision tubing, with a flow range of 0.001 to 2900 mL/min depending on tubing size. Stackability: Up to 4 Easy-Load 3 pump heads can be stacked on one compatible pump drive, making it an efficient solution for multi-channel applications. Easy Integration: Same-side tubing entry/exit permits easy integration into space-limited applications, with the option to mount and operate the pump head in any of four positions (depending on the drive).

Condition: excellent (used), functionality: fully functional, Year of construction: 2016, operating hours: 41,124 h, control type: CNC control, degree of automation: automatic, controller manufacturer: Siemens, laser type: CO₂ laser, laser source manufacturer: Rofin, laser source model: DC035, laser hours: 12,753 h, laser power: 3,500 W, pipe diameter (max.): 240 mm, pipe length (max.): 12,500 mm, workpiece weight (max.): 400 kg, input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, type of cooling: water, Equipment: CE marking, cooling unit, dust extraction, emergency stop, fume extraction, safety light barrier, 🔷 2016 BLM Adige LT8.10 CNC Tube Laser – 3.5kW CO₂ | 3D Tilt Head | 12.5m Load | Siemens Control Used 2016 BLM LT8.10 CNC tube laser for sale. 3.5kW CO2, Siemens control, 3D cutting head, 12.5m loader. Fully equipped with chiller & extraction. 💡 High Performance 3D Tube Laser Cutting System – Fully Automated 2016 BLM Adige LT8.10 CNC Tube Laser, a premium 3D tube laser cutting machine designed for high precision, flexibility, and productivity across a wide range of tube and profile cutting applications. The LT8.10 is one of the most versatile machines in its class, capable of processing round, square, rectangular, and structural profiles (I-beams, channels, etc.) with high accuracy and repeatability. 🔧 Machine Details Manufacturer: BLM Group (Adige) Model: LT8.10 Year: 11/2016 Type: CNC Tube Laser Cutting Machine Laser Type: CO₂ Laser Source: Rofin DC035 (3.5 kW) Control: Siemens CNC ⚙️ Key Features Cjdpjy Ir Eusfx An Nogu 3D Laser Cutting Head with Tilt Capability (±45°) High precision angular / bevel cutting Fully automatic tube processing Designed for high productivity and flexibility Automatic parameter adjustments for optimal cutting performance Capable of cutting complex geometries and joints 📏 Tube & Profile Capacity Round Tube Diameter: Ø12 – 240 mm Square Tube: up to 200 x 200 mm Max Bar Length: 12,500 mm (12.5m infeed) Unloading Length: 8,500 mm Max Linear Weight: 40 kg/m Max Total Bar Weight: 400 kg ✔ Processes: Round, square & rectangular tube Flat oval & special profiles Structural sections (I-beam, U-channel, angle, etc.) ⚡ Laser & Cutting Capabilities Laser Power: 3.5 kW CO₂ (Rofin DC035) 3D Bevel Cutting: Yes (tilting head) Automatic Focus & Adjustment Systems High quality edge finish Ideal for weld prep & complex fabrication work 🧠 CNC & Software Siemens CNC Control System User-friendly interface Full program control and automation High precision motion control for complex cutting operations 🔄 Loading & Handling System Automatic Tube Loading System Infeed Length: 12.5 metres Outfeed Length: 8.5 metres Automatic tube positioning & rotation Multi-position unloading capability ❄️ Supporting Equipment Included Chiller: Cosmotec WLAD842207ZAS0 Extraction Unit: Donaldson Torit DCE 2DFP4-SPRK Full integrated system ready for production 🧱 Machine Overview The LT8.10 is designed to deliver high precision without compromising productivity, making it ideal for both high-volume production and complex custom fabrication. Its rigid structure, automatic handling systems, and 3D cutting capability make it a top-tier solution for: Steel fabrication Structural engineering Tube processing companies Automotive & industrial manufacturing 💰 Why This Machine? Proven BLM Group reliability High-end 3D tube laser capability Handles large diameter tubes (up to 240 mm) Fully automated system → low labour cost Complete package with chiller & extraction Excellent value compared to new Notes: *Specifications are given in good faith but not guaranteed*

Condition: new, Year of construction: 2025, All-round fiber laser metal tube cutting machine Multiple function options help the laser tube cutting machine be used in numerous tube cutting processes. The slender nozzle allows the laser tuber cutter to avoid interference and cut various types of tubes, including special-shaped tubes like H-Beam, P-Beam, I-beam, etc. Cgsdpfshwrhmsx An Nou Cutting machine clamping becomes convenient, easy and fast, with 3 seconds at the soonest to clamp and high repeat precision Cutting performance and efficiency are improved by maintaining gas flow steady with little turbulence. BodorGenius, combined with the lightning-quick piercing process, completes the whole piercing during it moves down on Z-axis. Thanks to the technology, no reworking is necessary for medium and thick sheet piercing. Angle steel and channel steel cutting are standard with no need fior additional installation. Optimized edge searching method and algorithm guarantee higher cutting precision and better steadiness of the laser cutter. Condition: New Laser Type: Fiber Laser Laser Power: 1500W, 2000W, 3000W, 6000W Maximum machinable tube length: 6500mm/9200mm Chuck drive types: NC electric chuck Graphic Format Supported: AI, BMP, Dst, Dwg, DXF, DXP, LAS, PLT CNC or Not: Yes Cooling Mode: WATER COOLING

Condition: ready for operation (used), Year of construction: 2012, functionality: fully functional, type of input current: AC, input voltage: 400 V, year of last overhaul: 2025, input frequency: 50 Hz, Equipment: documentation/manual, Manufactured by Eurostar Italy - one of the leading filling manufacturers Designed for filling Apple Cider, Beer, CSD and still drinks Triblock -rinser - filler - capper 2,000 BPH at 500ml bottles 3,000 BPH at 330ml bottles Isobaric Counterpressure Filling, designed for cider, beer, and other still & sparkling beverages Double Pre-Evacuation with Vacuum Pump, ensuring minimal oxygen pickup for superior product quality 316 Stainless Steel contact parts for superior hygiene and durability Pneumatic Bottle Lifters - overhauled 2025 Twin-channel rinser with final blow-off - overhauled 2025 Crown Cap (26mm caps) Capper Bypass - to feed to other cappers Touch Screen Control Panel for easy operation and monitoring Siemens PLC System, providing precise process automation and flexibility Cgodpfx Aox A U Uron Nou Variable speed control via inverter drive CIP Cups, Cleaning fluid can be recycled Change Parts Included for 250ml, 330ml, 500ml, and 750ml glass bottles Heavy-duty stainless steel frame CE-compliant safety Includes all manuals Spare Parts package Spare Fill tubes - new for adaptation to any bottle fill height Spare filling valve seals etc. Can be loaded to buyer's transport

Condition: excellent (used), LDS Dactron COMET USB Shaker Control System Type: COM 200 Manufacturer: Brüel & Kjaer / LDS Dactron For sale is a used LDS Dactron COMET USB Shaker Control System, Type COM 200, for controlling electrodynamic vibration testing systems. The system is suitable for random, sine, and shock tests in laboratories, industrial settings, automotive applications, as well as research and development. Manufacturer / Model Manufacturer: LDS Dactron / Brüel & Kjaer Type: COMET USB Model: COM 200 Serial Number: 11303191 Made in U.S.A. Technical Data Cgedpsy Ugrpjfx An Nju 2-channel shaker control system USB interface Supply voltage: 100 – 240 V Frequency: 47 – 63 Hz Current consumption: 0.5 A Suitable for: Random tests Swept sine tests Shock tests Electrodynamic vibration testing systems Software / Functions Installed software according to system display: Shaker Control Version 8.1001 Library Version 6.3120 Unlocked module: Value Swept Sine Activated option: Real Time Data Exchange Connections USB port BNC connectors Power connection Further connections, see images Calibration Calibration data according to label: Calibration Date: 2010-09-21 Due Date: 2011-09-21 The calibration has expired. A new calibration can be performed by the buyer if required. Condition Used equipment from an industrial application. Optical condition, see images. Normal signs of use and storage are present. The device was switched on. The indicator light and software display are active. Further functional or calibration tests have not been performed. Scope of delivery LDS Dactron COMET USB COM 200 controller Power cable / connection cable according to images Accessories according to images Scope of delivery includes only the items shown in the images. Notes Inspection possible by arrangement. Loading and shipping possible by arrangement. Commercial sale without warranty. Subject to changes, errors and prior sale.

Condition: good (used), Power supply unit, DIN rail -360 W, 24 V/1 5 A -Power supply output type: Fixed/Adjustable -AC input voltage: 85 V to 132 V, 187 V to 264 V. -Number of output channels: 1 -Nominal output voltage: 24 V -Output current max.: 15 A -Power output max.: 360 W Codpfeb A Tffjx An Nogu -SVHC: No SVHC (19-Dec-2012) -Areas of application: Industrial -External width: 80 mm -Width: 80 mm -Input voltage change: 0.5 % -Frequency input-: 63 Hz -Frequency supply max.: 63 Hz -Power supply unit -Frequency supply min.: 47 Hz -Weight: 1.1 kg -Height: 125 mm -Load change: 0.5 % -Length: 125 mm -Length outside-: 125 mm -Mounting: DIN rail -Rated power: 360 W -Voltage output: 24 V -Voltage output max.: 28 V -Voltage output min.: 24 V -Current output: 15 A -Power supply type: switch mode -Depth outside: 125 mm -Supply voltage: 264 V -Supply voltage max.: 264 V -Supply voltage min.: 85 V

Condition: reconditioned (used), Year of construction: 2015, operating hours: 30,143 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 570 kg, overall weight: 20,000 kg, oil tank capacity: 600 l, year of last overhaul: 2026, volume flow: 800 m³/h, Technical data baler: Manufacturer Presona AB, Sweden Type LP 60 VH1 Year of construction 2015 Cgsdpfxjy S Rtle An Nsu Total operating hours, 30,143 hours, as of July 2025 Effective pump running time onl 6,527 hours, as of July 2025 Number of pressed bales 115,193 bales, as of July 2025 Press force pre press 25 t Main press force 60 tonnes Specific pressing force 73N/cm² Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Theoretical throughput capacity 800 m³/hour Throughput capacity under operating conditions 350 m³/hour Bale dimensions 1,100 x 750 mm Drive power 37 kW Tying 5-fold vertical, fully automatic Throughput capacity with a Bulk weight of 50 kg/cbm 11 to 14 tonnes/hour Bale weights 420 to 570 kg, depending on material Hydraulic oil tank volume 600 litres Baler dimensions assembled with hopper 10,100 x 3,750 x 4,310 mm (l x w x h) Transport dimensions excluding press 10,100 x 2,400 x 3,000 mm (l x w x h) Machine weight press approx. 20 tonnes Condition of the press: The press was partially overhauled in our workshop and then tested in manual and automatic mode. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Grease cartridges of the automatic roller lubrication system replaced Slide rails cut out from the press floor in the press room Underbody reinforced with welded sheets New HARDOX slide rails welded in Wire station with deflection rollers for the lower wire cleaned and made operational Slide rails cut out from the floor in the press channel New HARDOX slide rails welded in Both side walls of the press channel dismantled, derusted Worn side wall plates cut out Complete side walls covered with new wear plates and welded Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Machine checked, general maintenance work carried out and press tested in manual and automatic mode Comments: The press is sold without a conveyor belt and without wire stations. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 1996, functionality: fully functional, pressing force: 170 t, filling opening width: 1,020 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, overall weight: 40,000 kg, oil tank capacity: 3,000 l, year of last overhaul: 2025, volume flow: 750 m³/h, For sale is a used baling press system consisting of a chain belt conveyor for underfloor operation, with a feed hopper, a hydraulic pre-compactor with ruffler, a MACPRESSE 111A baling press, two complete wire drawing frames with 5 wire reel stands each, without wire. Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 111A Year of construction 1996, refurbished in 10/2024 Press power main press 170 tons Specific press capacity 14 kg/cm² Feed channel 1,800 x 1,020 mm Filling volume 2,5 cm³ Theoretic throughput rate 750 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 55 kW Tying system 5-fold horizontal, full automatic Throughput rate at a approx. 30 up to 35 tons/h, depends on material Volume hydraulic oil tank 3,000 l Transport dimensions of press with new machine feets 113,700 x 2,300 x 2,900 mm (l x w x h) Machine weight baler approx. 40 tons Comments: The baler was partially overhauled in our workshop and tested after completion of the work, please look at our functional video. The system was previously used to bale paper and cardboard from municipal collections. The contract was awarded elsewhere after the end of the contract period, so the complete system is for sale. The overhaul work carried out and the spare parts replaced can be found in the detailed photo documentation and in our quotation. Cgsdpfx Ajy S Rqwon Neu The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Technical data conveyor belt: Manufacturer Wagensfeld B.V. Type chain belt conveyor 1700 mm Year of construction 2017 Drive power 7.5 kW Belt speed 14 m/minute Length of infeed conveyor 6,900 mm Length of ascending belt 12,885 mm Length of gooseneck 1,747 mm Overall length 21,271 mm Pitch 32° Effective width 1,644 mm Height of drive shaft above ground 5,777 mm Wall height of feed conveyor 500 mm Wall height of ascending conveyor 880 mm Steel flights height 40 mm Distance between flights 1200 mm Transport dimensions conveyor disassembled 15,005 x 2,503 x 2,435 mm (l x w x h) Pit dimensions 11,500 x 2,700 x 1,015 mm (l x w x d) Remarks: The chain belt conveyor, built in 2017, was later made to fit the baler during the last installation of the baler in the Netherlands and is newly installed. The conveyor belt is in good, operational condition and has therefore not been overhauled. An installation drawing with the pit dimensions is available. Scope of delifery: 1 chain belt conveyor, Wagensveld B.V. 1 piece feed hopper with pre-compressor flaps 1 piece wirbulator 1 baler MACPRESSE, type 111A 2 wire drawing frames with wire reel stands, without wire 1 operating manual with CE declaration, electrical and hydraulic circuit diagram

Condition: used, mileage: 500 km, power: 375 kW (509.86 HP), first registration: 12/2025, fuel type: diesel, overall weight: 32,000 kg, axle configuration: > 3 axles, color: white, gearing type: automatic, Year of construction: 2025, Equipment: ABS, air conditioning, electronic stability program (ESP), navigation system, ++ RENT ++ BUY ++ RENT ++ BUY ++ RENT ++ BUY ++ RENT Internal number: #398 Mercedes-Benz Arocs 3551 8x4 with Combined High Pressure Jetting and Suction Pressure Tank Body ADR Type K 1.0-18.0 / 28 PE This Mercedes-Benz Arocs 3251 8x4 with KROLL ADR combined jetting and suction pressure tank body is a NEW vehicle, built for the highest performance requirements. With VacuStar WR 3100, Uraca KD 718, large hose storage cassette, DN125 telescopic boom, and complete ADR L4BH equipment, it is immediately ready for demanding sewer, industrial, and hazardous goods applications. Body • Manufacturer: KROLL Fahrzeugbau-Umwelttechnik GmbH • Tank material: S355J2+N (St 52.3) • ADR suction/pressure tank Type K 1.0-18.0 / 28 PE • Ejector piston with 3 locking positions • Suction from open waters possible (“comfort version”) via boom cassette with integrated filter • Tanker equipment ADR – Type class AT/FL L4BH • Discharge via pneumatically actuated piston • Sludge water outlet DN80 for backflushing via the boom into the channel Vacuum System • CVS VacuStar WR 3100 – approx. 3,100 m³/h at 400 mbar • Approx. 20 m HD hose DN125 • Hose storage cassette with simultaneous telescopic boom DN125 • Parallel routing of suction and HD hoses over the boom • Reach on hit side: 5,200 mm • Hydraulic suction hose reel on the right with 30 m DN75, fully passable High-Pressure System • Uraca KD 718 – approx. 315 l/min at 170 bar • Large HD hose reel for 240 m DN25, 180° swiveling • Equipped with 160 m DN25 • Small HD hose reel for 80 m DN13, hydraulic • Equipped with 80 m DN13 Special Features • Hose storage cassette with telescopic boom DN125 • Continuously adjustable suction hose height (hydraulic, roller guide carriage) • Hydraulic, telescopic, 180° swiveling boom arm • Electric cable winch on the boom • ADR L4BH, including EX/II, EX/III and AT • Spray gun • LED beacons • LED ambient lighting • CAN-BUS remote control for work functions • Radio remote control with 14 functions • Hot water hand washing unit • Large locker rear left (e.g. for push camera) • Reversing camera • Sound insulation for pump compartment • Large equipment box • Toolbox • Holder for traffic cones • Vice • Ladder • Large advertising boards right & left Special Equipment • Axle load measuring system • Digital radio DAB/DAB+ Cgjdexc Sz Nopfx An Nju • ADR equipment package • Right-hand outer mirror with maneuvering position • 220 Ah battery • Interactive multimedia cockpit • 24V / 100A electrical pre-installation cab • High beam and cornering light assistant • Movable cab entry • Front suspension: 9.0 t / 4-leaf • Remote online query function • Tinted windshield with band filter • Vehicle without trailer coupling • ADR hazardous goods version Type FL • Speed limiter • 16-speed gearbox G 280-16 • Gearbox lock (independent of transmission) • Rear axle ring gear 300 • 3-piece mudguards with splash protection • Fuel tank 290 l aluminum, left • Cool box / refrigerator • Cooling package for hot regions • Front air intake • Reinforced engine brake • Trailing axle: 9 t steered, relievable, liftable • Navigation system • PTO – smooth flange • PTO independent of transmission and dependent on clutch MB 1.65 • Programmable special module • Wheelbase variant 3,900 mm • Frame overhang 1,200 mm • Re

Condition: used, Year of construction: 2004, Fujitsu Luxel T-9000 CTP (Model PT-R8100) – CTP plate exposer - Quantity: 1 - Manufacturer: Fujitsu - Type: Luxel T-9000 CTP E - Model: PT-R8100 - Application: Imaging of thermal CTP printing plates - Plate size: up to approx. 1,165 x 940 mm - Resolution: up to 2,400 dpi - Plate thickness: 0.15 – 0.30 mm - Laser technology: Thermal laser (multi-channel) Cgjdpowv D T Tofx An Nsu - Output capacity: approx. 20–30 plates/hour (depending on resolution) - Compatible with various workflow systems - Robust construction for prepress department

Condition: used, Year of construction: 2002, - Light source: 16-channel infrared laser diodes - Minimum plate size: 324 x 370 mm - Maximum plate size: 830 x 660 mm - Resolution: 2400/2438/2540 dpi - Media type: infrared thermal plates - Media thickness: 0.15 to 0.3 mm - Productivity: 10 plates per hour at 2400 dpi - Dimensions: 1750 x 1030 x 1178 mm Cgedpfxowv D Dxs An Nou - Weight: 645 kg

Condition: used, Year of construction: 2008, Manufacturer: Kolbus / Cermi • Model: XCR 650 • Machine Type: Front-Cut / Front Cutting Unit for Flap and Brochure Production • Application Area: Print Finishing / Book and Brochure Manufacturing • Function: – Gathering channel with feed and alignment of brochures – Opening of inserted flaps – Front-Cut: Precise front cut for processing flap brochures – Automatic feeding and stacking of finished products • Fields of Application: – Processing of flap brochures and similar print products – Inline integration into finishing or binding lines – Can also be used as a stand-alone machine • Format Range (typical): – Max. trimmed size approx. 480 × 350 × 50 mm – Min. trimmed size approx. 125 × 100 × 3 mm – Max. untrimmed size approx. 480 × 375 × 50 mm – Min. untrimmed size approx. 125 × 105 × 3 mm • Performance: – Mechanical output depending on settings up to approx. 6,000 cycles/h (single cut) – Throughput mode up to approx. 8,000 cycles/h possible :contentReference[oaicite:1]{index=1} • Special Features: – Precise front cut for demanding brochure formats – Suitable for inline production lines – Robust, industrial-grade design Cgsdpfx Aex Hxq Ion Nou • Typical Industries: Print finishing, bookbinding, printing houses

Condition: excellent (used), Brüel & Kjaer LDS Dactron Laser USB LAS 200 Type: LAS 200 LDS Dactron Vibration Testing and Shaker Control System including Acer laptop with installed software For sale is a used LDS Dactron LASER USB Shaker Control System, Type LAS 200. The system was last used in an industrial vibration testing facility and is suitable for electrodynamic shaker systems, vibration tests, resonance tests, random tests, and shock tests. Manufacturer / Model Manufacturer: LDS Dactron / Brüel & Kjær Type: LASER USB Model: LAS 200 Made in U.S.A. Software / Functions Installed software: Shaker Control Version 8.1001 Library Version 6.3120 Activated modules according to software display: Random Sine on Random Random on Random Swept Sine Resonance Search, Track and Dwell Sine Oscillator Classical Shock Shock Response Spectrum Long Time History Further activated options: Automatic Drive Notching / Limiting Real Time Data Exchange High Frequency Control Amplifier Controller Technical Data 8 active input channels 2 output channels Sampling Rate: 96 kHz A/D Resolution: 24 Bit USB Mode: 2.0 Input Type: Volt / ICP / TEDS Suitable for electrodynamic vibration testing systems and industrial shaker systems. Calibration Calibration data according to system display: Last calibration: 09/20/2023 Displayed due date: 09/19/2024 Dimensions / Weight Controller approx.: 430 x 350 x 90 mm (W x D x H) Controller weight: approx. 6 - 8 kg Scope of supply LDS Dactron LASER USB Controller Acer laptop with installed software Connection cables / accessories as shown in the pictures Condition Used equipment from industrial use. Optical condition see pictures. Normal signs of wear and tear and storage. System starts, software can be opened Cgjdsy T Iv Hopfx An Nju and the hardware has been recognized. No further tests were performed. Notes Sale exclusively to commercial customers. No guarantee or warranty. Subject to prior sale, errors and changes. We will be happy to answer any further questions by telephone or message.

Condition: good (used), Centrifugal pump, high-pressure pump, water pump, multi-stage vertical centrifugal pump -Manufacturer: Siemens Hinsch, side channel pump type CEHF 3104 -Motor: AEG 22 kW / 2915 rpm -Dimensions: 1680/800/H990 mm Cjdjhn S Slspfx An Negu -Weight: 394 kg

Condition: used, Dimensions (LxBxH): 770 x 400 x 410 cm Connection: 400 volt Saw blade diameter: 350 mm Cedsy U H Uqepfx An Nsgu Working range: 2500 mm x 1600 mm Including lift table (2500x1500 mm) Including flexible extraction channel, fixed channels not included Total dimensions: 7700x4000x4100 mm CE compliant: no, however a possibility to be converted to a CE compliant machine like the description of lot 1 Online auction of woodworking machinery, workshop equipment, wood inventory and sawn logs and beams due to discontinued operations and warehouse and workshop closure. Including a De Meyer CNC panel sawing machine, Van Roeyen industrial dust collector, Power-Lift lift tables, full outdoor kitchen with BBQ, outdoor lounge, demo exhibition stand, sawn logs of chestnut, Douglas, oak, sycamore, elm and teak The online auction opens Wednesday 6 May and closes Thursday 25 June. Register your account via our website and place your bid. For viewings and inspections check the auction information on the website. Viewing days are on: - Tuesday 26 May - Tuesday 26 May Pickup days are on: - Thursday 2 July - Thursday 2 July Dome Auctions is an innovative auction platform dedicated exclusively to the industrial sector. By focusing on machinery sales from business closures, restructurings, and bankruptcies, we provide a trusted marketplace where buyers and sellers connect with confidence. Unlike general auction houses, Dome Auctions specializes in selling complete industrial assets directly from factories, ensuring quality and reliability. With a commitment to transparency, industry expertise, and tailored service, we streamline the sales process and maximize value for all parties. As online auctions continue to grow in the European industrial market, Dome Auctions offers a professional and efficient solution for companies seeking high-quality machinery at competitive prices.

Condition: used, Dimensions (LxBxH): 810 x 570 x 235 cm Equipped with new control box, servo motors, pressure cylinders to hold plate flat Connection: 400 volt Saw blade diameter: 300 mm Maximum cutting area: 2500 mm x 1600 mm Lift table not included Control brand: IndraMotion MTX micro Equipped with safety systems such as light curtains, safety fence Including flexible extraction channel, fixed channels not included Overall dimensions: 8100x5700x2350 mm CE compliant: yes converted machine to CE compliant Online auction of woodworking machinery, workshop equipment, wood inventory and sawn logs and beams due to discontinued operations and warehouse and workshop closure. Including a De Meyer CNC panel sawing machine, Van Roeyen industrial dust collector, Power-Lift lift tables, full outdoor kitchen with BBQ, outdoor lounge, demo exhibition stand, sawn logs of chestnut, Douglas, oak, sycamore, elm and teak Cgsdpey U H Ukjfx An Nou The online auction opens Wednesday 6 May and closes Thursday 25 June. Register your account via our website and place your bid. For viewings and inspections check the auction information on the website. Viewing days are on: - Tuesday 26 May - Tuesday 26 May Pickup days are on: - Thursday 2 July - Thursday 2 July Dome Auctions is an innovative auction platform dedicated exclusively to the industrial sector. By focusing on machinery sales from business closures, restructurings, and bankruptcies, we provide a trusted marketplace where buyers and sellers connect with confidence. Unlike general auction houses, Dome Auctions specializes in selling complete industrial assets directly from factories, ensuring quality and reliability. With a commitment to transparency, industry expertise, and tailored service, we streamline the sales process and maximize value for all parties. As online auctions continue to grow in the European industrial market, Dome Auctions offers a professional and efficient solution for companies seeking high-quality machinery at competitive prices.

Condition: good (used), functionality: fully functional, Gitterbox emptying, pneumatic, for gitterboxes 1200 x 800 mm Csdev Nhk Djpfx An Negu Dimensions: 2200 x 1700 x 2250 mm (LxWxH) Weight approx. 1500 kg Note: The machine is in good condition. It was checked and tested by us in 28816 Stuhr. You can find the video above in the pictures, or on our website or our YouTube channel. Inspections, even under power, are possible at any time by arrangement. Video calls are possible on request. We are happy to answer questions about the machine by phone from Monday to Thursday from 8 a.m. to 2 p.m. On Friday we are there for you from 8 a.m. to 1 p.m. Please note: All technical data refers to information provided by the manufacturer. We accept no liability for the information provided or any errors. The offers are non-binding, subject to prior sale and can be revoked at any time. Viewings are possible by arrangement. The sale takes place ex location, without warranty or guarantee. Our payment terms are 100% advance payment.

Condition: good (used), Year of construction: 2018, operating hours: 1,011 h, functionality: fully functional, Shredder GROSS, Model GAZ 82 S, Year of Manufacture 2018 Technical specifications: Manufacturer: GROSS Apparatebau Model: GAZ 82 S Year of manufacture: 2018 Operating hours: 1,011 Drive power: 37 kW Feed opening: 800 x 1200 mm Hopper volume: 1 m³ Rotor diameter: 368 mm Rotor length: 800 mm Rotor speed: 60–120 rpm Extraction nozzle diameter: 200 mm Transport dimensions: approx. 2100 x 1700 x 2600 mm (LxWxH) Weight: approx. 2,600 kg Suitable materials: Wood, cardboard, plastics Cedpfx Asx Uz N Ajn Nsgu Accessories: Hopper Remarks: The shredder is in good condition. It has been inspected and tested at our location in 28816 Stuhr. You can find a video on our website or YouTube channel. Inspections, including under power, are possible at any time by appointment. On request, we can also carry out tests with your material for a handling fee. If you have any questions about the machine, we will be happy to answer them by phone from Monday to Thursday from 08:00 to 14:00. On Fridays, we are available from 08:00 to 13:00. Please note: All technical data are based on information provided by the manufacturer. We accept no liability for the stated details or for any errors. This offer is non-binding, subject to prior sale, and may be withdrawn at any time. Inspections are possible by arrangement. Sale is ex works upon advance payment, without warranty or guarantee.

Condition: good (used), Year of construction: 2015, operating hours: 1,932 h, functionality: fully functional, Baler Presto CC 50 M, semi-automatic, year of manufacture 2015, with lift-and-tilt device Technical Specifications: Manufacturer: Presto Model: CC 50 M Year: 2015 Operating hours: 1,932 Pressing force: 50 t Cycle time: 52 s Drive power: 7.5 kW Filling opening: 1030 x 1100 mm Filling volume: 0.85 m³ Tying: 3-fold, wire, manual Throughput depending on bulk density: 35 kg/m³ – 1.3 t 60 kg/m³ – 1.7 t 100 kg/m³ – 2.2 t Bale dimensions: 750 x 1100 mm Bale weight: 300 kg Dimensions: 4705 x 1680 x 2540 mm (LxWxH) Machine weight: approx. 4,000 kg Materials: Paper, cardboard, film The operating manual is available in German. Csdpfjyz R Etsx An Negu Note: The machine is in good condition. It has been inspected and tested at our premises in 28816 Stuhr. The video is available on our website or YouTube channel. Please note: All technical data is based on information from the manufacturer. We accept no liability for the details provided or for any possible errors. Subject to prior sale; offer is non-binding and may be revoked at any time. Inspections are possible by arrangement. Sale is ex works against advance payment, without warranty or guarantee.

Condition: good (used), Year of construction: 2017, operating hours: 1,640 h, functionality: fully functional, Baler Presto CC 40 M, Year of manufacture: 2017 Technical Specifications: Manufacturer: Presto Cgedeyz R Hqjpfx An Nju Model: CC 40 M Year of manufacture: 2017 Pressing force: 40 t Cycle time: 34 s Drive power: 15 kW Feed opening: 1080 x 1100 mm Feed volume: 0.85 m³ Binding: 4-fold, polyester strapping, manual Throughput rate at bulk density of: 35 kg/m³ - 1.8 t/h 60 kg/m³ - 2.5 t/h 100 kg/m³ - 3.1 t/h Bale size: 750 x 1100 mm Bale weight: 400 kg Dimensions: 3650 x 1590 x 2010 mm (LxWxH) Machine weight: approx. 3,800 kg Materials: Paper, cardboard, film The baler is in good condition. It has been inspected and tested by us. A video can be found on our website or YouTube channel. Operating instructions and CE declaration are available. Note: Channel discharge is fully automatic and regulated. Please note: All technical data is based on the manufacturer's information. We do not accept liability for the information provided or any possible errors. This offer is non-binding, subject to prior sale, and may be revoked at any time. Inspections are possible by appointment. Sale is ex-works, prepayment required, without warranty or guarantee.

Condition: ready for operation (used), Year of construction: 1979, functionality: fully functional, Baler Paal Pacomat II, Year of Manufacture 1979 Technical Specifications: Manufacturer: Paal Model: Pacomat II Year of Manufacture: 1979 Drive Power: 11 kW Pressing Force: 27 t Channel Cross Section: 700 x 1000 mm Filling Opening: 1000 x 650 mm Throughput: approx. 60/115 m³/h Cgedpjyz Salefx An Nsu Bale Size: 700 x 1000 mm Bale Weight: up to 400 kg Machine Dimensions: approx. 7000 x 2000 x 2000 mm (LxWxH) Machine Weight: approx. 5200 kg Materials: Paper, Cardboard, Film Remarks: The machine is in fully functional condition. It has been inspected and tested at our site in 28816 Stuhr. You can find the video on our website or our YouTube channel. Viewings, including under power, are possible at any time by appointment. Please note: All technical details are based on information provided by the manufacturer. We accept no liability for the accuracy or possible errors. Offers are subject to change, prior sale reserved, and may be revoked at any time. Viewings are possible by prior arrangement. Sale is ex works, without warranty or guarantee. Our payment terms require 100% advance payment.

Condition: good (used), Year of construction: 2015, functionality: fully functional, Baling Press Dixi 60 SLD, Year of Manufacture 2015 Manufacturer: Dixi Model: Dixi 60 SLD Year of Manufacture: 2015 Drive Power: 7.5 kW, 400 V / 32 A Feed Opening: 990 x 1,110 mm (W x L) Pressing Force: 60 t Press Cycle: approx. 47 s Bale Size: 800 x 1,100 x 1,200 mm (W x H x L) Bale Weight: approx. 370–410 kg Strapping: 3-fold, manual Machine Dimensions: approx. 4,150 x 1,725 x 2,035 mm (L x W x H) Machine Weight: approx. 5,420 kg Materials: Paper, cardboard, film The press is in good condition. It has been inspected and tested by us. A video is available on our website or YouTube channel. The operating manual and CE declaration are included. If you have any questions about the machine, we are happy to assist you by phone from Monday to Thursday, 08:00–14:00. On Fridays, we are available from 08:00–13:00. Cgsdoy Ni Euepfx An Nou Please note: All technical data is based on information provided by the manufacturer. We do not accept any liability for the accuracy of the details or potential errors. This offer is subject to change, prior sale reserved and may be withdrawn at any time. Viewings are possible by appointment. Sales are ex works, against advance payment, without warranty or guarantee.

Year of construction: 2012, condition: good (used), functionality: fully functional, Rotary Airlock Valve / Rotary Valve Nestro, year of manufacture 2012, for the separation / differentiation of paper chips or paper edge strips Technical data: Manufacturer: Nestro Lufttechnik GmbH Year of manufacture: approx. 2012 Motor: 4 kW Max. volumetric flow: 28,000 m³/h Cgodpfsy Tiagsx An Nju Max. inlet diameter: 450 mm Speed: 22 rpm Rotor width: 1,500 mm Rotor diameter: 1,200 mm Dimensions: 2,200 x 2,200 x 2,500 mm (LxWxH) Weight: approx. 3,000 kg Remarks: The machine is in good condition. It has been inspected and tested at our facility in 28816 Stuhr. You can find the video above on our website or on our YouTube channel. Inspections, including under power, are possible at any time by prior arrangement. We are happy to answer your questions about the machine by phone, Monday to Thursday from 08:00 to 14:00. On Fridays, we are available from 08:00 to 13:00. Please note: All technical data is based on information provided by the manufacturer. We do not accept liability for the stated information or possible errors. Offers are non-binding, subject to prior sale, and may be withdrawn at any time. Inspections are possible by arrangement. Sale is ex-works, advance payment required, without warranty or guarantee.