Used Dovetailers for sale (176)

Condition: used, Year of construction: 2022, Maximum parent roll width: 1420 mm Minimum parent roll width: 600 mm Maximum parent roll diameter: 1500 mm Maximum parent roll weight: 2500 kg Maximum unwinding tension (Ø1500 mm): 600 N Minimum unwinding tension (Ø1000 mm): 40 N Minimum standard slitting width: 100 mm Maximum rewinding width: 1400 mm Maximum rewinding diameter: 1050 mm Maximum rewinding weight: • Ø76 mm shaft: 600 kg • Ø152 mm shaft: 1000 kg Hedpjyx Uy Ajfx Andsnu Maximum rewinding tension: 600 N Maximum production speed: 600 m/min Power supply: 3 x 400V 50Hz Installed power: 30 kW Compressed air: 6 bar, dry Materials to be slit: • Paper-based / liner-based packaging laminates. • Board from 80 to 300 g/m². Unwind section: A separate between-centers unwinder, type T9, 1500 mm diameter, including: • Hydraulic cylinder control for lifting parent rolls from the floor. • Two motors driving the unwinding roll, controlled by an ultrasonic diameter sensor and a tension-control dancer roller. • Two pneumatic expanding adapters, SVECOM, for 70/76 mm (3”) cores. • Two pneumatic expanding adapters, SVECOM, for 150/152 mm (6”) cores (mounted on the pneumatic end adapters). • Floating edge-correction roller. • Automatic web guiding system, FIFE DP20, with SE26A photoelectric sensor, ±100 mm correction via electric actuator — for controlling sheet edge or continuous printed line. • Connecting walkway allowing web threading at floor level while keeping full access to the slitting station. • All web path rollers are anodized. • Safety guarding for operator protection. Slitting section: A slitting station with individual pneumatic knives and circular counter-knives: • Shear cut performed against the counter-knives. • Counter-knife shaft driven by an independent motor; counter-knife shaft is pneumatic. • Pneumatic knife holders mounted on a beam with a dovetail guide (TIDLAND) and an air supply manifold for individual activation. • 10 slitting sets, each including: Individual TIDLAND pneumatic knife holder (25 mm width) and double-bevel circular knife Ø 90/60 mm. • Set of multi-groove counter-knife rings, 5 mm pitch, 50 mm length. Web separation section: • A separator roller driven by the slitting motor; angle and curvature fully adjustable. Lay-on roller: • Lay-on roller made of anodized ground aluminum or polyurethane (depending on materials). • Pressure is adjustable and synchronized with winding diameter. • Roller is removable. Automatic splicing / transverse cutting system: • Hydraulically operated pivoting arm including a transverse knife with linear motion and a backing plate for securing the web onto new cores. Trim extraction system: • Trim suction unit with two width-adjustable nozzles. • Turbine enclosed in a sound-insulated cabinet, conveying trim to a centralized system or container (not included). Rewinding section: • Motorized turret (two-position) supporting two rewinding shafts. • Rewinding shaft drive by an oversized asynchronous motor. • Hydraulic centering point for the active rewinding roll. • Two pneumatic expanding shafts Ø76 mm (3”), max load 600 kg each, equipped with full-width rubber strips with individual bladders. • Two pneumatic expanding shafts Ø152 mm (6”), max load 1000 kg each, also equipped with full-width rubber strips with individual bladders.

Condition: excellent (used), Year of construction: 2009, Bernardo FM 45 V drilling and milling machine. The FM 45 V drilling and milling machine offers an optimal price-performance ratio thanks to the standard spindle feed. The dovetail guide of the gear head ensures maximum precision and stability. Drilling capacity in steel 32 mm Drilling capacity in cast iron 40 mm Throat 260 mm Spindle speed (12) 50 - 2520 rpm Spindle mount MK 4 Quill stroke 120 mm Quill feed (3) 0.12 / 0.19 / 0.26 mm/rev Table size 820 x 240 mm Distance spindle / table 40 - 485 mm Travel path (x / y) 550 / 190 mm Height adjustment of milling head 400 mm T-slot size Hodpfx Asvutw Hjndenu 14 mm T-slot distance 55 mm Motor output power S1 100% 0.85 / 1.1 kW (400 V) Motor input power S6 40% 1.1 / 1.5 kW (400 V) Machine dimensions (W x D x H) 1150 x 850 x 1450 mm Weight approx. 285 kg Standard with automatic spindle feed and thread cutting device Large speed range 50 - 2520 rpm (12 levels) Dovetail guide for x, y and z axes, adjustable via wedge strips Versatile application options, slot milling, face milling, boring,.... Solid large cross table, precisely surface-machined Milling: spindle feed via handwheel Drilling: spindle feed via handwheel High-quality aluminum motor, designed for continuous operation Stable and vibration-free cast design Simple and quick speed change using a gear lever Pivoting milling head for angle drilling, milling bevels, etc. Location: from stock 54634 Bitburg - available at short notice -

Condition: ready for operation (used), Compact Dovetail Jointing Machine Output: approx. 4-6 joints/min. For wood profiles with the following dimensions: Thickness: 30-120 mm Width: 75-250 mm Pressing force: 22.5 t Automatic glue application via 2 glue combs, designed for processing PUR glue. Spring-mounted with a safety cut-off system that immediately stops the milling and glue application feed in case of even the slightest load. All parts are chrome-plated. Electrical system with PLC Milling motor power: 22.00 kW Hydraulic unit: 29.50 kW Oil cooler: 0.75 kW Hjdpjzmmr Rofx Andonu Infeed drive: 1.50 kW Outfeed drive: 2.50 kW Cut-off saw: 3.00 kW Total power consumption: 59.25 kW = 120 amps In the past, jöma has successfully delivered and commissioned 10 of these machines. We can supply all spare parts for the compact dovetail jointing machine. We, jöma, have been supplying and repairing Cook Bolinders machines for 30 years.

Condition: excellent (used), Year of construction: 2012, functionality: fully functional, Set for micro-dovetail jointing for high-volume and mass production Features: – High-performance production line, – Heavy-duty working units, – High feed rates, – Accelerated handling movements ensure high throughput. Depending on the desired output, additional buffer conveyors can be integrated to speed up the production process. TENONER FC-10KZ-6 Specifications Values Milling spindle 50 x 210 mm; 5,500 rpm Spindle motor 18.5 kW Chipper saw (special) 300/60 x 8 mm Saw motor 6 kW Working table width 600 mm Workpiece package height 30 to 150 mm PRESS FC-10PZ6 Specifications Values Board width/thickness 30-150 mm / 20-70 mm Finished board length 6,000 mm Line capacity up to 15,000 linear meters/shift The following modifications and upgrades have been made to the machine: - New electrical installation - Machine controller replaced with SIEMENS SIMATIC S7 and SIEMENS SIMATIC HMI panel - New infeed table before the tenoners with buffering system - New board turning mechanism – side feeder after tenoners (chain-driven turning mechanism controlled by frequency inverter) - New chain feeder before the press (length 4,500 mm) - Additional pre-scoring aggregates for finger-joint gluing – furniture board installed at the tenoners Machine dimensions: Hnedjx Idl Hopfx Andou 16.5 m x 5 m

Condition: ready for operation (used), Year of construction: 2010, Fully automatic dovetail cutter system: Double-pack type Machine has been dismantled Machine will be inspected with functional guarantee Specifications: Wood input length: min. 200 mm max. 4000 mm Wood cross-section: min. 20 x 40 mm max. 80 x 220 mm Wood output length: 18,000 mm Max. wood cross-section with 10 mm dovetail size: hardwood 120 cm² softwood 150 cm² Dovetail design: vertical and horizontal Adhesive type: PUR Electrical power: Connection voltage: 400 V Control voltage: 24 V 50 Hz System is completely wired up to the control cabinet. Dovetail length / optional wood cross-section and adhesive type can still be adjusted. Hnodpfeznh Szex Andsu Performance: 6 milling tables/min Working height: 960 mm Table width: 600 mm Adhesive application: double-sided application With continuous packaging

Condition: used, Workbench vice, parallel vice LEINEN with dovetail guide and height adjustment. Model: 125. Jaw width: 125 mm. Jaw height: 23 mm. Clamping range: max. 200 mm. Overall height: 550 to 750 mm. - 360° rotatable. - Dovetail guide. - Anvil surface for light straightening work. - Approx. 200 mm height adjustment without lift system. Weight: 44.5 kg. Good condition. Hnsdpfxsy E T Dyj Andju

Condition: used, Year of construction: 1993, Used Machine Year of manufacture: 1993 Features and technical specifications: - Machine bed cast entirely from gray iron in a single piece - With wide table supports and dovetail guides for the vertical slide Hnsdpfozyy Dtjx Andsu - With control panel above the table - Interchangeable spindle with MK 5, 30 mm diameter - Milling spindle swivel angle: 45°/22.5° - 2 motors: 5.5/7.5 kW – 400 V - 4 speeds without belt change: 3000–4500–6000–9000 rpm - Cast-iron table with table top extensions on both sides, 2150 mm - Solid cast-iron milling stop with quick adjustment (overall) and individual adjustment for both jaws - ELGO 89P23 control unit for height, tilt, and stop - Program memory for 99 programs - With sliding table insert - With Maka 4-roller feed unit - Dimensions L x W x H approx. 2150 x 1430 x 1740 mm - Weight approx. 1450 kg

Condition: excellent (used), Lista drawer cabinet with milling tools Lista drawer cabinet Hodpfx Anoq Aa I Tjdjnu Number of drawers: 13 Drawer type: Full extension Very high load-bearing capacity due to the precise and stable construction made of high-quality, welded sheet steel Body color: Reseda green, RAL 6011 Load capacity per drawer: 200 kg External dimensions W x D x H: 720 x 710 x 1000 mm Contents: Metal circular saw blades Disc milling cutters, cross-toothed & coupled Disc milling cutters, cross-toothed Angle half-round milling cutters Dovetail milling cutters Half-round milling cutters Thread milling cutters More items - new and used - can be found in our shop! International shipping costs available upon request!

Condition: good (used), Year of construction: 2010, functionality: fully functional, milling height: 180 mm, WEINIG NKT Dovetail Grooving Line – Double Unit DP20 An industrial dovetail grooving and gluing machine – developed for maximum precision and efficiency. Technical specifications: Wood input length: min. 130 mm | max. 1000 mm Wood output length: min. 3700 mm | max. 7400 mm (half lengths possible!) Hnedpez E Awqsfx Andou Wood cross-section: min. 20 x 40 mm | max. 80 x 180 mm Cutter diameter: 370 mm Dovetail design: Vertical / Horizontal, 10/11 dovetails, 3.8 mm pitch Glue application: 2-sided, PVAC white glue Connection power: 80 kW Note: The machine is currently disassembled and is in our warehouse. An inspection is possible by appointment. Scope of supply: WEINIG NKT Double Unit DP20 including control unit Integrated gluing station for 2-sided application Operating manual & documentation Hydromat 17B (7 spindles) General information Manufacturer: Weinig AG Model: Hydromat 17B // 7 spindles (various tools) Type: High-performance profiling milling machine / planing and rabbeting machine Year of manufacture: 1989 Operating voltage: 380 V / 50 Hz Bottom-Right-Left-Right-Left-Top-Bottom table, fixed Description Heavy-duty, high-performance planing and rabbeting machine made of vibration-damping and torsion-resistant cast iron components in a modular system. Designed for precise and economical woodworking with high continuous output. Mechanical feed, adjustable in the range of 5 – 35 m/min, feed motor 5.5 kW (7.5 HP). Surfacing table 2 m long, quick adjustment available. Chip removal for surfacing and jointing spindles, adjustment range 10 mm each. Technical data • Feed speed: 5 – 35 m/min, mechanical • Feed motor: 5.5 kW / 7.5 HP • Operating voltage: 380 V / 50 Hz • Table length: 2000 mm • Adjustment range of chip removal: 10 mm (surfacing and jointing side) • Machine design: Without counter bearing, in high-performance design

Condition: as good as new (ex-display), Year of construction: 2025, minimax ti 55es LL – Table saw The illustration shows the T 55 i elite s in its standard version. The professional machine for skilled tradespeople, featuring a pivoting milling spindle and 4 speeds. M Digital: motor-driven height adjustment and pivoting. Sturdy steel and cast iron construction. Oversized milling unit made of cast iron, pivoting up to -45° to the rear. LED display of milling speeds. Fast, trouble-free speed change via eccentric clamping. Clockwise/counterclockwise rotation. Display of height and inclination with 1/10 mm accuracy. Heavy-duty professional fence: with fine adjustment via rack and pinion, with numerical display, aluminum fence cheeks, 3-way positioning for quick repetition of the setting. Scope of delivery: Aluminum fence cheeks Arched milling guard Table extension on the left and right Hedpfedqzh Rjx Andonu Model: minimax ti 55es LL Article no.: 5502252 Technical data Dimensions of the work table: 2500 x 655 mm Dimensions of the format sliding table Usable length of the spindle: 125 mm Max. tool diameter: 240 mm Max. tool diameter (lowered): 230 mm Max. tool diameter (dovetail cutter): 320 mm Spindle inclination: 0 to -45 degrees Speeds: 3500/6000/8000/10000 min-1 Motor power 400 V/ 50 Hz / S6-40%: 5.0 kW Dust extraction port diameter: 2 x 120 mm

Condition: new, Year of construction: 2025, Heavy-duty, solid cast-iron construction High running smoothness due to ground, oil-bath lubricated gears Right-hand/left-hand operation Automatic quill feed with manual fine feed Motorized positioning of the Z-axis Motorized table feed of the X-axis Coolant system Machine lamp Gear head can be swiveled ± 60° Adjustable wedge strips Solid dovetail guide for the column, hand-scraped, for maximum stability and precision Height-adjustable, large-sized protective shield with microswitch Drilling depth stop Digital position display DRO 5 Drilling/tapping function Solid and large-sized cross table, precisely surface-finished with T-slots and adjustable wedge strips Solid machine base made of cast iron with chip collection groove Single-stage, high-quality industrial electric motor Large speed range of 60 - 2,760 rpm through 2 continuously adjustable speeds Dimensions and weights Length approx. 1600 mm Width/Depth approx. 930 mm Height approx. 2110 mm Weight approx. 495 kg Drilling/Milling performance Arbor size max. 63 mm Shell mill size max. 26 mm Drilling capacity steel (S235JR) 24 mm Continuous drilling capacity steel (S235JR) 20 mm Electrical data Connection voltage 230 V Mains frequency 50 Hz Electrical connection Total connected load 1.5 kW Milling table, horizontal Length 800 mm Width 240 mm Distance Vertical spindle - Milling table max. 420 mm T-slot size 14 mm Number of T-slots 3 T-slot spacing 80 mm Standards and approvals Standard DIN EN 55011 EMC class C2 Travel X-axis manual 560 mm Y-axis manual 195 mm Z-axis manual 350 mm X-axis automatic 480 mm Vertical spindle Overhang 258 mm Spindle mount MK 4 Speed range 60 – 2760 rpm Number of speed ranges 2 Hnodpfxjg U Uv Ue Andou Speed control Steuerung der Drehzahlregelung electronic Draw bar M 16 Swivel range milling head Z - X plane ± 45 ° Quill diameter 75 mm Quill stroke 120 mm Location: In stock at 54634 Bitburg - available immediately -

Condition: used, Year of construction: 1999, functionality: fully functional, Schmidler S4 Joinery Line - 4-strand transverse infeed conveyor (inclined upwards) - Infeed roller conveyor - Edge turning device integrated in the infeed roller conveyor - Zero point detection - Electronically controlled under-table swing cross-cut saw Saw blade diameter: 710 mm Swivel angle: 360 degrees Tilt angle: 0–65 degrees - Waste wood pusher - Marking pen, horizontal (from below) and vertical (from behind) - Universal milling unit incl. finger-joint cutter and dovetail milling head - Horizontal drilling unit – rafter nail drilling device - Vertical drilling unit - Vertical profiling mill (lower position) for internal radii - Powered outfeed roller conveyor - Pneumatic push-off ruler - Transport and measuring system - Control system incl. color display Maximum workpiece dimensions: Height: 300 mm Width: 400 mm Length: approx. 12,000 mm Hodpeya Dc Ijfx Andonu 4-Side Planer – Schmidler Minimum workpiece dimensions: Height: 30 mm Width: 50 mm Feed speed: 9/18 m Planer shaft diameter = 140 mm 4-sided chamfering unit Infeed roller conveyor Outfeed roller conveyor with push-off ruler and storage rods Machine in good used condition, fully operational and in use. The machine can be inspected by appointment. Available for sale immediately or by arrangement.

Condition: refurbished (used), Year of construction: 2004, functionality: fully functional, General Control system: SIEMENS 840 D Main spindle Bar capacity: 60 mm Speed: 6000 rpm Power: 29 kW Torque: 140 Nm Synchronous spindle Technology: Mounted on the turret Mount: Collet chuck, D = 42 mm Maximum speed: 4,500 rpm Turret 1 (X/Z) Technology: Tool turret with 8 stations Tool holder: For DIN 69880 - 25x48 mm Maximum speed: 6000 rpm Power: 3.3 kW Maximum torque: 7.5 Nm X-axis: 90 mm Z-axis: 280 mm Turret 2 (X/Z) Technology: Tool turret with 6 stations Tool holder: Symmetrical dovetail mount Speed: 4,500 rpm Power: 4.2 kW Torque: 7.5 Nm X-axis: 81 mm Z-axis: 80 mm Equipment Hnjdpfxjzgcp So Andju Chip management: Hinged belt chip conveyor Coolant management: Coolant pump, 8 bar Part removal: Workpiece removal device Bar loader: Bar loader magazine LM 3200 Ejector: On the synchronous spindle

Condition: good (used), Year of construction: 2001, functionality: fully functional, FMB MBZ 75 - 80, 5-axis FMB multi-machining center, Type MBZ - 2 / 72-80 / 5, Year of manufacture 2001, PC control with TFT color display, Travel range X/Y/Z 7000/1000/370 mm, Hnsdpfx Anozhuitsdeu Milling head with high-frequency spindle for aluminum, Spindle speed up to 18,000 rpm - 7.5 KW, Tool changer, 12-position, Tool holder HSK 40, 2-axis NC dovetail milling head, 8 pneumatic clamping elements, Swivel machining possible, Program generator, FMB programming software, Pneumatic material stop, Measuring / probing device.

Condition: used, functionality: fully functional, Metering and application system Hydrotop 1 E400R + Ecotac_C for single-component (1K) PUR edge gluing for package dovetail joint systems Glue application – dovetail joint Adhesive application – dovetail joint in very good condition Hnodpfx Aoul Shnendju functionality tested

Condition: excellent (used), Year of construction: 2026, functionality: fully functional, Equipment: CE marking, TECHNICAL SPECIFICATIONS Maximum mounting hole dimensions: 3500 x 2500 mm Minimum mounting hole dimensions: 250 x 350 mm Vertical cylinders: 2 pcs, ø 65/40 mm, stroke 1300 mm Total lifting capacity of vertical cylinders: 7.4 tons Horizontal cylinders: 2 pcs, ø 50/30 mm, stroke 1500 mm Total lifting capacity of horizontal cylinders: 2 tons Hedpfxoznv A Ue Andonu Hydraulic unit 1.5 kW *The maximum size of the workpiece will be smaller than the maximum operating range of the press, depending on the type of joint (dovetail or pin) and the method of positioning the workpiece in the machine (pre-assembled or unassembled). PRESS DESCRIPTION • 3 positions for the lower beam • Pressure is adjusted directly from the hydraulic unit using a knob; the current pressure is displayed on an indicator during operation. • All electrical components are manufactured in accordance with European standards; each component has a code corresponding to the marking on the electrical diagram. • Hydraulic unit with a pump in an oil bath for better noise reduction and lubrication. A 1.5 kW motor is installed on the oil tank. • The rack and pinion system allows for precise movement of the upper beam. • The supporting structure is made of welded iron elements, Fe 430 grade. • Control panel: - Button for vertical movement of the beam - Button for vertical clamping - Button for opening the horizontal clamping corners - Button for horizontal clamping of the corners - Additional button for two-handed activation of the press functions Warranty: 12 months on spare parts

Condition: used, Counter bearing and adapter for milling machine for horizontal milling Counter bearing and adapter (counterholder) for DECKEL milling machine (Bearing block with dovetail mounting adapter DECKEL FP1 + FP2) Type 9570 Dovetail width, narrow: approx. 72 mm Dovetail width, wide: approx. 88 mm Dovetail height: approx. 15 mm Length (bearing block): 133 mm Width (bearing block): 50 mm Total height (bearing block): 105 mm Hnsdpfxoxcbl De Andju Bearing bore: Ø 17 mm (with bronze bearing bushing) Distance from bore axis to dovetail mounting face: approx. 82.5 mm (center height) - Adapter fits dovetail and mounting surface, raises center height by 22.5 mm to 105 mm Total length (dovetail rail): 635 mm Weight: 3.8 kg Very good condition

Condition: ready for operation (used), Year of construction: 1990, functionality: fully functional, overall weight: 300 kg, Cross Slide – Support Type PS 35 Support suitable for hand-operated bending machines with a 350 mm center height Technical Data Longitudinal slide travel: 360 mm Cross slide travel: 150 mm Height: 325 mm Rotary table diameter: 215 mm Hnsdpfxjxp Sfhs Andou Shear length: 550 mm Weight approx.: 300 kg Machine Description - Technically inspected and ready for operation - Robust cast iron construction - Adjustable dovetail guides - Trapezoidal spindle for longitudinal and cross slide - Large dimensioned handwheels

Condition: repair required (used), functionality: unexamined, Dovetail slotting machine for wood packages dimter HK 400 Dovetail slotting machine Input lengths: 800–6000 mm Cutting height: 285 mm, optionally 300 mm Color: Blue Consisting of: Pos. 01 Packaging unit Pos. 02 Package roller conveyor Pos. 03 Central milling cutter Pos. 04 Package roller conveyor Pos. 05 Package singulation unit Pos. 06 Chain cross conveyor Pos. 07 Infeed roller conveyor Pos. 08 Cycle press Hodpfevi Hw Nex Andenu Pos. 09 Feed unit Pos. 10 Cut-off saw Including control cabinets and operator panels The machine requires repairs and is sold in its current condition. It has already been dismantled and is stored in Achern. All technical documentation is available. We are available at any time to answer questions about the machine and provide technical information. We will provide consulting support for repair and reassembly.

Condition: refurbished (used), DKV III continuous press with braking unit Completely overhauled Hnjdpjv T Aqyofx Andeu Optional with original hydraulic motors or with servo motors Options: - Chain threading - Co-rotating cut-off saw Function: For pressing the dovetail joint without stopping (in a continuous process). The upper and lower plate chains generate the feed force. Downstream braking plates transmit the required longitudinal pressing force to the wood through friction. Advantages: - High performance despite a relatively slow feed rate - Absolutely no vertical displacement of the dovetail joints Technology: Heavy-duty plate chain 2", pneumatically adjustable Braking elements are floating Press force measurement via contact manometer Height adjustment electrically Maximum press force adjustable and dependent on feed rate and wood cross-section, 4500 daN at 32 m/min 2200 daN at 70 m/min Feed rate adjustable 10-70 m/min Drive power Adjustment of infeed unit 1 kW Adjustment of brake 1 kW Hydraulic motors 45 kW Technical data: Wood width 90 - 180 mm Wood thickness 20 - 80 mm Ratio thickness - width 6 : 10 Wood cross-section with 15/16.5 mm tenon max. 90 cm²

Condition: new, Year of construction: 2026, Holzkraft Minimax ST 5es – Maximum configuration for professionals Saw-milling combination with miter cutting device and pivoting milling spindle Art. No.: 5501086 Ø 350 mm main saw blade with 118 mm max. cutting height, which is also achieved when the scoring saw blade is installed Scoring device with separate motor and Ø 120 mm saw blade, easily and precisely adjustable from the outside Saw unit can be pivoted from 90° to -45° High-precision format sliding table made of anodized aluminum Large extension table (1200 x 650 mm) With material roller and extendable aluminum telescope stop up to 3300 mm Pivoting milling spindle from 90° to -45° towards the rear into the milling fence Four milling speeds With right/left rotation of the milling spindle Three independent motors With lockable main switch, motor protection switch Supplied as standard with separate saw parallel fence and separate jointing fence for planing Equipment details: Sliding table with ball contact system Made of anodized aluminum Guides made of hardened and ground steel, 15% harder than conventional steel Double-bearing milling unit Pivoting, made of cast iron Mounting points directly on the table, resulting in optimal smoothness Milling spindle mounted high up on precision ball bearings, resulting in low bearing load and maximum possible service life Powerful industrial motors Milling fence Heavy-duty professional design The high-quality milling fence made of cast iron is supplied as standard with fine adjustment 3-way positionable for quick resetting of the setting With fine adjustment via rack and pinion, numerical display and aluminum milling fence jaws Parallel fence With fine adjustment and quick clamping Stable round bar guide made of ground steel Can be conveniently folded down for cutting large workpieces Interchangeable aluminum ruler for narrow workpieces Cast iron double-bearing saw unit Height adjustment via dovetail guide Extremely robust and torsion-resistant for precise cuts Close to the saw blade, bearing on both sides Height and adjustable up to 45° Scoring unit with separate scoring motor 0.55 kW as standard Extension table with angle-adjustable telescope stop with degree grid division Dimensions and weights Weight approx. 900 kg Dust extraction connection Dust extraction nozzle diameter 3 x 120 mm Dust extraction nozzle diameter saw blade guard 80 mm Drive power Scoring motor 0.55 kW Main motor 2 x 5.0 kW Electrical data Connection voltage 400 V Format sliding table and table Format sliding table width 360 mm Format sliding table height 142 mm Table length 1380 mm Table width 465 mm Milling spindle Spindle inclination 0 – -45 ° Usable length of the spindle 125 mm Spindle speeds 3500/6000/8000/10000 min⁻¹ Milling tool diameter max. Lowerable 240 mm Mortise milling 320 mm Circular saw unit and scoring saw Cutting length 3200 mm Cutting width with parallel fence 900 mm Hnjdpfx Ansd Hx Hmsdju Max. ripping width to the left of the saw blade 3300 mm Saw blade inclination 90 - 45 ° Max. cutting height 90° 104 mm Max. cutting height 45° 68 mm Location: In stock, 54634 Bitburg - available immediately -

Condition: new, Year of construction: 2026, CORMAK ZX 7055 VARIO Milling and Drilling Machine Main Advantages Rigid cast iron base and column – ensures stability when machining demanding workpieces, reduces vibration, and extends tool life. Variable spindle speed control in two ranges: 75–438 rpm (low range) and 438–2500 rpm (high range) – allows optimal parameter selection according to tool diameter and material type. Automatic spindle feed – provides consistent cutting performance and reduces the risk of drill breakage during deep-hole drilling. Tapping function – once the preset thread depth is reached, the spindle automatically switches to reverse rotation. Ground gears – ensure smooth and quiet gearbox operation with stable spindle torque. Dovetail guideways on all axes – provide precise table movement and reliable machine geometry. Swiveling head ±90° with height adjustment – facilitates chamfering, undercutting, and angular machining operations. Forward and reverse spindle rotation – enables safe tapping and tool withdrawal. Efficient cooling system – effectively dissipates heat during machining, prevents overheating of both the tool and workpiece, and improves machining accuracy and tool life. Standard Equipment Variable spindle speed control Electrically powered spindle head height adjustment Coolant system Technical Description Heavy-Duty Cast Iron Construction The robust cast iron construction forms the foundation of the machine’s durability and precision. The ZX 7055V DRO milling and drilling machine maintains excellent stability even during the most demanding operations. Hnjdpfx Aszd R Eisndju The machine features continuously variable spindle speed adjustment in two ranges: Low range: 75–438 rpm High range: 438–2500 rpm Large Cross Table with Precision-Ground Surface Attention to detail is a key design feature. The large cross table with a precision-ground surface ensures excellent flatness, resulting in highly accurate machining. Dovetail Guideways Innovative dovetail guideways provide smooth and precise movement along all three axes, enabling outstanding machining results without compromise. Forward and Reverse Rotation Adapt the machine to your requirements. The ability to rotate the spindle in both directions provides additional flexibility during machining operations. Swiveling Head ±90° and Adjustable Head Height Handle a wide variety of machining tasks thanks to the ±90° swiveling head and adjustable head height. Achieve precise results under all working conditions. Optional Machine Base A machine stand/base is available as an optional accessory. Technical Specifications Parameter Value Maximum Drilling Capacity Cast Iron (HT200) 45 mm Steel 32 mm Maximum Face Milling Capacity 80 mm Maximum End Milling Capacity 28 mm Table Size 820 × 240 mm Table Travel (X/Y) 595 / 185 mm Maximum Tapping Capacity M24 Spindle Taper MT4 Spindle Speed Range Low Range 75–438 rpm High Range 438–2500 rpm Spindle Travel Manual 107 mm Automatic 100 mm Distance from Spindle to Column Surface 250 mm Maximum Distance from Spindle Nose to Table Surface 445 mm Motor Power S1/S6 1.5 / 1.8 kW Net Weight 350 kg Overall Dimensions (L × W × H) 1084 × 924 × 1550 mm Height with Base 2150 mm

Condition: used, Keyway milling head, head for DECKEL milling machine, type FP 1 Factory number: 21948 Dovetail width: approx. 74 - 88 mm Dovetail height: approx. 14.5 mm Dovetail length: 285 mm Distance from the front edge of the dovetail to the center of the gear: approx. 200 mm Stroke size: max. 80 mm Stroke rate: max. 475 double strokes/min. Tool holder: 4-sided, 16 x 16 mm with clamping plate - Stroke size adjustable via eccentric adjustment - Drive from the machine gearbox, within the dovetail guide (as with the normal vertical head) - This keyway milling head is inserted into the dovetail guide in place of the normal vertical milling head (Mounting in place of the vertical milling head) Hodpfx Ansznn Hrodenu - Drive gear in the keyway milling head, 39 teeth, gear width 15 mm, presumably 15° pressure angle - Keyway milling head can be rotated 360° on the flange plate, degree scale +/- 35° - Small breakout point on the housing Weight: 28.5 kg DECKEL FP1 has a pressure angle of 15° on the drive wheel. DECKEL FP2 + FP3 have a pressure angle of 20° on the drive wheel.

Condition: good (used), total height: 2,500 mm, total length: 5,300 mm, total width: 2,500 mm, feed length X-axis: 1,550 mm, feed length Y-axis: 600 mm, grinding height: 800 mm, overall weight: 7,800 kg, GER RS 15/60 grinding machine Table 1500 x 600 mm X-axis travel 1550 mm Y-axis travel 600 mm Maximum grinding height 800 mm Wheel size 400 x 100 mm Hnsdjvli H Sjpfx Andeu Automatic infeed Yes Dovetail accessory Yes Cooling system Yes Machine dimensions (width x length x height) 2500 x 5300 x 2500 Weight 7800 kg

Condition: good (used), Modular aggregate unit, format processing unit, machining unit, milling unit, form milling unit, jointing milling unit, end-cutting unit, double-end tenoner, edge processing machine, scoring motor, chipper motor, milling motor for edge processing machine -HOMAG milling unit for: joint milling -with: heavy dovetail guide -Milling unit: swiveling -3x: Perske Motors -Engine 1: Type KCS 70.12-2 D -Power: 3/4.4 kW -Voltage: 220/380/380 Volts -Frequency: 50/100 Hz -Speed: 2880/5880 rpm -Engine 2: Type KCS 70.12-2 D -Power: 3/4.4 kW -Voltage: 220/380/380 Volts Hedpfx Ansdx Aiwedenu -Frequency: 50/100 Hz -Speed: 2880/5880 rpm -Motor 3: Type KNS 51.14-2 D -Power: 1/2 kW -Voltage: 220/380/380 Volts -Frequency: 50/100 Hz -Speed: 2750/5700 rpm -Other engines with different performance levels are available from us for an additional charge. -Number: 1x joining milling unit available -Price: per piece -Dimensions: 1370/1100/H1330 mm -Weight: 608 kg