Used Plate Press for sale (23,215)

Condition: good (used), Year of construction: 1991, Electric workshop hydraulic press Capacity: 50 tons. Pjdpfozhfzmex Abgopu Table width: 800 mm, cylinder stroke: 200 mm.

Condition: used, Year of construction: 1966, pressure 040 t throat 240 mm stroke 8- 88 mm number of strokes - idle run 130 /min shut height (stroke down, adjustm. up) 320 mm ram adjustment 63 mm Ppodpjy Nd Svofx Abgeu table surface area 560 x 435 mm ram surface 250 x 200 mm hole in the table 150 mm table height over floor 950 mm total power requirement 4 kW weight of the machine ca. 3,3 t dimensions of the machine ca. 1,7 x 0,85 x 2,4 m

Condition: used, Year of construction: 1976, pressure 025 t table-size 500 x 400 mm ram stroke - adjustable min/max 20- 120 mm throat 250 mm ram surface 350 x 250 mm strokes of ram per min. 120 shut height (stroke down, adjustm. up) 300 mm ram adjustment 60 mm tool shank hole (depth x diameter) 32 x 80 mm Pedpfxsy Nd Spj Abgjpu hole in the table 180 mm weight of the machine ca. 1,6 t Machine has adjustable table (150 mm).

Condition: used, Year of construction: 1990, pressure 100 t table surface area 800 x 800 mm ram stroke 450 mm throat 400 mm dayligth 800 mm table height over floor 900 mm die cushion capacity 40 t Ppjdjyif Nrepfx Abgeu die cushion stroke 200 mm oil volume 700 l rapid traverse - down 185 mm/sec rapid traverse - up 160 mm/sec working feed 55 mm/sec total power requirement 17 kW weight of the machine ca. 5 t dimensions of the machine ca. 2,2 x 1,2 x 3,4 m Machine has cushion in table.

Condition: used, Year of construction: 1997, sheet width 0610 mm plate thickness 1,5 mm distance between columns 650 mm front stop - adjustable 0- 300 mm Pjdpfxsxu Nrpo Abgepu angle stop 45-90 Grad operating pressure 6 bar strokes per minute 60 total power requirement 3 kW weight of the machine ca. 0,27 t dimensions of the machine ca. 1 x 1 x 1,5 m

Condition: used, Year of construction: 1971, sheet width 2000 mm plate thickness 16 bei St 42 mm passage width 2250 mm impact length 1000 mm blade length 2005 mm throat 600 mm cutting gap adjustment 0,05 - 0,95 mm cutting angle 1° 40' ° down holder 10 Stück back stop - adjustable 10 - 1000 mm table: 2500 x 700 table height over floor 800 mm quantity of oil 900 l Ppjdpfx Abjww Nccjgou weight of the machine ca. 10 t dimensions of the machine ca. 3 x 2,3 x 2,3 m voltage 380 V Food switch, material support beams, spare knifes.

Condition: used, Year of construction: 1994, sheet width 3000 mm plate thickness 16 mm distance between columns 3200 mm throat 310 mm stroke 300 mm table width 820 mm table height over floor 1215 mm Ppjdjt Tqkdepfx Abgju Number of downholders 12 St. cutting angle 0,5 - 2,5 ° cutting angle adjustment 1- 2,5 ° back stop - adjustable 0- 1000 mm total power requirement 30 kW weight of the machine ca. 19 t dimensions of the machine ca. 3,8 x 2,65 x 2,85 m Machine was overhauled in 2010 and was modernized with light barrier at table. Machine has an automatic back stop with DRO. Cutting angel is adjusted by motor. Cutting gap is manually adjusted by adjustment of table. Along with the machine we supply a loading/unloading table.

Condition: used, Year of construction: 2020, functionality: fully functional, pressing force: 120 t, filling opening width: 2,000 mm, filling opening length: 1,000 mm, bale width: 750 mm, bale height: 1,100 mm, total width: 2,835 mm, total height: 4,374 mm, total length: 19,627 mm, overall weight: 43,000 kg, warranty duration: 12 months, power: 75 kW (101.97 HP), Equipment: documentation/manual, For sale is a baling press, model "HP-G 4 120 VG6," manufactured in 2020, featuring a 6-strand vertical PP twine tying system. The pictures show the machine in its assembled condition. It is now located at our facility in Lathen. The press is sold without a conveyor belt. Before delivery, the machine will be completely overhauled and technically refurbished by our qualified personnel. Our goal is to provide you with a reliable and immediately operational machine that meets the requirements of daily operation. The overhaul includes, among other things, the following services: • Disassembly and inspection of the relevant machine components • Evaluation of all wear-relevant components • Replacement or refurbishment of worn parts • Inspection and repair of the press ram and associated guide elements • Inspection and, if necessary, replacement of wear plates, slide guides, and bearing points • Inspection of the press channel and restoration of the required tolerances • Overhaul of the hydraulic components, including cylinders, valve technology, and hydraulic hoses Ppjdozhudqspfx Abgsu • Replacement of seals, wear parts, and connecting elements • Inspection of the electrical components and safety devices • Inspection and readjustment of the tying device • Cleaning, assembly, and commissioning of the overhauled system • Performance of functional and load tests after completion of the work Thanks to the comprehensive overhaul, you will receive a technically inspected machine with high operational reliability and a long service life. We will be happy to provide you with further information, photos, or a customized offer. If you are interested, we look forward to hearing from you.

Condition: good (used), Year of construction: 1997, HEIDELBERG CD 102-5 OFFSET PRINTING PRESS Year: 1997 Colors: 5 Sheet Size: 720 x 1020 mm Impressions: 212 Million Available now: Heidelberg CD 102-5 five-color offset printing press in good operating condition. • 5 Printing Units • Alcolor Dampening System • CPC 1-04 Ink Control • CP Tronic Console • Technotrans Refrigeration & Circulation System • Preset Functions • Autoplate Semi-Automatic Plate Changing • IR Dryer • Automatic Blanket Washers • Chrome Cylinders • Anti-Setoff Powder Spray System • High Production Capacity • Excellent Print Quality • Immediate Availability Technical Specifications: Manufacturer: Heidelberg Model: CD 102-5 Year: 1997 Colors: 5 Maximum Sheet Size: 720 x 1020 mm Impression Count: 212 Million Applications: • Commercial Printing • Packaging Printing • High-Quality Offset Printing Pedpfx Aozgug Asbgjpu Contact us for additional photos, videos, inspection appointments, pricing, and delivery options worldwide. Heidelberg CD 102-5, Heidelberg CD102, Heidelberg Offset Press, 5 Color Printing Press, Offset Printing Machine, Used Heidelberg Press, Commercial Printing Press, Heidelberg Alcolor, Heidelberg Autoplate, Heidelberg CPC 1-04, Heidelberg CP Tronic, Packaging Printing Machine, Sheetfed Offset Press, Printing Equipment For Sale.

Condition: new, Year of construction: 2017, Exhibition machine Year of manufacture: 2017 (has not yet been used in production) The Compact Star is a pneumatic gluing press with 5 gluing levels. The rotary motion is provided by a pneumatic drive with safety interlocking. Each level has 4 adjustable vertical clamps with an adjustable counter bearing. Each vertical clamp is equipped with a hold-down rail. Furthermore, each level has 2 adjustable horizontal pressure bars with counter bearings. Maximum clamping dimensions: Vertical: 960 mm Horizontal: 1335 mm Material thickness: 50 mm Dimensions: Length: 2700 mm Width: 3117 mm Height: 3096 mm Availability: short notice Ppodpfx Ajkwg Szjbgeu Location: Röllbach

Condition: used, color: other, Dimensions (LxBxH): 20 x 20 x 1 cm Feeding system for flat and angle steel Equipped with a feed cart and material clamp (maximum length: 15,200 mm) Equipped with Vacon 110 software with CNC control Vacon 110 CNC touchscreen control Hydraulic shear for flat steel – VPS 2200 Cutting force: 220 metric tons Maximum length: 15,200 mm Maximum width x thickness: 500 x 25 mm Pjdpfxezhatwj Abgopu Cutting angle: CNC 45° left and 45° right Hydraulic angle shear for steel – VHS 2400 Cutting force: 240 metric tons Maximum length: 15,200 mm Maximum angle steel dimensions: 200 x 200 x 16 mm Hydraulic punching – VPO 1000 Punching force: 100 metric tons Punching capabilities: Punch diameter / thickness: Ø 57 mm / 15 mm or Ø 32 mm / 25 mm 4 punching units for flat steel (vertical position) 1 punching unit for angle steel (horizontal position) Includes tools Dismantling and loading costs by Voorman technician: 15,000 euros. Hydraulic counter / numbering unit – VNI 1/36 1 coding disc 36 characters Character height x depth: 10 x 1 mm Hydraulic power unit – VHA 37 Power: 37 kW Pressure: 250 bar Total length: 29 meters Total width: 5.56 meters Online auction of machinery and equipment from a steel fabrication company due to relocation, including a VOORTMAN CNC flat and angle steel processing line, MICROSTEP plasma cutting machines, a GEMA powder coating machine with drying oven and exhaust system, WHEELABRATOR blasting machine, MEUSER & CO radial drilling machine, DURMA CNC hydraulic guillotine shear and press brake, LVD press brake, HACO guillotine shear, BEHRINGER semi-automatic miter band saw, PEDDINGHAUS punching and universal punching-shearing machines, RÖSLER shot blasting machine, various DEMAG overhead cranes, VERNET DIJON forging hammer, AMADA CNC punching and nibbling machines, METORA band saw with roller conveyor, etc. The online auction opens Thursday 25 June and closes Tuesday 7 July. Register your account via our website and place your bid. For viewings and inspections check the auction information on the website. Pickup day is on: - Thursday 9 July Dome Auctions is an innovative auction platform dedicated exclusively to the industrial sector. By focusing on machinery sales from business closures, restructurings, and bankruptcies, we provide a trusted marketplace where buyers and sellers connect with confidence. Unlike general auction houses, Dome Auctions specializes in selling complete industrial assets directly from factories, ensuring quality and reliability. With a commitment to transparency, industry expertise, and tailored service, we streamline the sales process and maximize value for all parties. As online auctions continue to grow in the European industrial market, Dome Auctions offers a professional and efficient solution for companies seeking high-quality machinery at competitive prices.

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, oil tank capacity: 1,300 l, power: 75 kW (101.97 HP), year of last overhaul: 2025, For sale is a overhauled Bollegraaf baler, with 100 tonnes pressing force, large bale format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding system Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press tested in manual and automatic mode, accepted and stored after completion of overhaul work. Psdpfx Abszdn H Rogspu We accept no liability for the technical specifications or any errors.

Condition: excellent (used), Tire press Approx. 125 tons of pressing force Stroke 600 mm Ppedpfx Aozfwpqsbgeu Clear width 1520 mm Max. installation height 1300 mm Motor 5.5 kW 380 Volts Height 3080 mm Can be reduced to 2500 mm for transport purposes. Depth 800 mm Width 2750 mm Weight 2.8 tons.

Condition: good (used), Year of construction: 2008, pressing force: 300 t, control type: CNC control, actuation type: hydraulic, CNC crowning Hydraulic tool clamping EFL Easy Form laser measuring & correction system Set tooling Laser guide protection Controlled axis Y1/Y2/X/R/V-Axis Ppjdewrza Aspfx Abgeu Max. bending length: 4000mm Distance between supports: 3150mm Max. pressing force: 320T Distance table mount: 570mm Max. stroke: 300mm Table width: 200mm Support throat: 400mm Descent speed: 120mm/min Working speed: 14mm/min Return speed: 130mm/min X-axis range: 1000mm Control: CADMAN Power: 42kW Length: 5800mm Width: 2300mm Height: 3800mm Weight: 23000kg

Condition: good (used), Rolling width: 2050mm Rolling thickness 3x toproll Ø:18mm Rolling thickness 5x toproll Ø:21mm Rolling thickness prebending: 12mm Top Roll Ø: 280mm Side roll Ø: 260mm Number of rolls: 3 Rolling speed: 0-5 Adjustiment lower roll: 0-150mm/min. Adjustment side rolls: 0-150mm/min. Top support: yes Power: 12kW Length: 3000mm Ppedpjwtpgtefx Abgou Width: 1500mm Height: 1600mm Weight: 5200kg

Condition: used, Year of construction: 1963, total length: 2,300 mm, total width: 1,500 mm, total height: 2,880 mm, Empty weight: 8.000 kg Pedpfx Abewmfrrogopu - Year: 1963 - Documentation available: No - CE certificate present: No - Serial number: 12691 - Drive system: Conventional - Press force [ton]: 160 - Min. stroke [mm]: 25 - Max. stroke [mm]: 118 - Table length [mm]: 950 - Table width [mm]: 650 - Ram width [mm]: 340 - Height adjustment [mm]: 75 - Motor power: 7.5kW - Transport dimensions: 2300mm x 1500mm x 2880mm (l x w x h) - Transport weight [kg]: 8000kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 1989, total length: 1,600 mm, total width: 1,700 mm, total height: 2,750 mm, Empty weight: 4.000 kg Psdpfx Ajx Dkfpebgspu - Year: 1989 - Documentation available: No - CE certificate present: No - Serial number: 4414 - Drive system: Conventional - Press force [ton]: 63 - Min. stroke [mm]: 8 - Max. stroke [mm]: 100 - Table length [mm]: 800 - Table width [mm]: 560 - Ram width [mm]: 300 - Motor power: 5.5kW - Transport dimensions: 1600mm x 1700mm x 2750mm (l x w x h) - Transport weight [kg]: 4000kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 1981, total length: 2,000 mm, total width: 1,100 mm, total height: 2,300 mm, Empty weight: 500 kg - Year: 1981 - Documentation available: No - CE certificate present: No - Press force [ton]: 63 - Table length [mm]: 710 - Table width [mm]: 505 - Ram width [mm]: 280 - Throat depth [mm]: 250 - Transport dimensions: 2000mm x 1100mm x 2300mm (l x w x h) - Transport weight [kg]: 500kg - Transport packages [pcs.]: 2 Ppsdjxhcgyspfx Abgou Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 2009, total length: 2,700 mm, total width: 1,700 mm, total height: 3,900 mm, Colour: Green Empty weight: 5.000 kg - Year: 2009 - Documentation available: No - CE certificate present: No - Drive system: Conventional - Press model: Workshop press - Press force [ton]: 200 - Min. stroke [mm]: 1 - Max. stroke [mm]: 1100 - Table length [mm]: 730 - Table width [mm]: 1900 - Transport dimensions: 2700mm x 1700mm x 3900mm (l x w x h) - Transport weight [kg]: 5000kg - Transport packages [pcs.]: 2 Financial information Ppedpfx Abezdnzhogou VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: ready for operation (used), Brand: HSM Type: V-press 860 plus Year of manufacture: 2012 Pressing force: 418 kN Voltage: 400 Max. bale weight: 480 kg (depending on the material) Bale dimensions: 120 x 120 x 78 cm Machine weight: 2083 kg Machine dimensions: 180 cm x 125 cm x 298.5 cm Feed opening dimensions: 120 cm x 65 cm Ppsdpezg Dptefx Abgou Video available upon request.

Year of construction: 2026, condition: used, NEW, built in 2026 Automatic loading and unloading station. Suitable for solid wood, MDF, gypsum board, cement fiber board, and planks. Examples: Doors, planks, MDF panels, cabinet fronts, gypsum board, and facade panels. Adaptations to other products are possible. The machine operates at a constant speed andwith a set loading and unloading capacity. This allows you to easily automateyour loading and unloading processes and increase process reliability. The system operates with a 2-circuit vacuum system. Siemens control panel. Technical Specifications: - Manufacturer: Ka-Ma - Model: KR-1300-1 - Working width: 1,300 mm - Includes belt conveyor, length 3,000 mm - Working height: 930 ± 50 mm - PLC control, operated via a touch panel, Siemens S7-1200 - Loading and unloading of parts via 2 suction plates, length 442 mm Ppjdpfxjy S S Htj Abgeu - Automatic signal upon completion of the loading process - Max. horizontal speed: 0.5 m/s - Horizontal working stroke: 1,300 mm - Max. vertical speed: 0.5 m/s - Stack height approx. 1,000 mm (including pallet under the plate stack) - Loading side on the left in the direction of travel - Vertical working stroke: approx. 1,200 mm - Max. lifting capacity: approx. 85 kg, continuous operation 65 kg - Max. component width: 1,300 mm - Max. component length: approx. 2,850 mm - Max. conveyor belt speed: continuously variable up to max. 10 m/min. - Electric motor power: 1.5 kW- Electronic components: Schneider Electronics and Siemens - Weight: 1,200 kg Optional: 2-circuit vacuum system with 4 additional suction cups and the ability to lift the panels 15 mm on one side before vertical movement; required for all materials that can be vacuum-sealed. YouTube link:?v=WpRUnvPFqN0

Condition: used, Year of construction: 1985, sheet width 1000 mm plate thickness 5,0 mm Pjdpfozhn Ucex Abgjpu distance between columns 1100 mm 1010 mm Cutting length variabel mm cutting gap adjustment variabel mm connected load 5,0 kW weight of the machine ca. 2,5 t dimensions of the machine ca. 1,8 x 1,6 x 1,7 m Hydraulic guillotine shear with - Cutting gap adjustment - Support arms - Squaring arm

Condition: good (used), Year of construction: 2004, machine/vehicle number: H7761, functionality: fully functional, operating hours: 9,655 h, power: 380 kW (516.66 HP), input voltage: 500 V, input current: 530 A, input frequency: 50 Hz, stroke length: 1,650 mm, operating speed: 68 mm/s, total length: 7,000 mm, total width: 5,000 mm, total height: 6,000 mm, overall weight: 288,000 kg, SCHULER SHC 1000 Hydraulic Press / Industrial Robot Pjdpfozhuf Uex Abgjpu - Rated force: 1000 kN - Maximum stroke: 1650 mm - Installation height: 2400 mm - Closing speed: 420 mm/s - Working speed: max. 68 mm/s - Working speed at rated force: 21 mm/s - Tool base area: max. 3900 x 2400 mm - Tool base area: min. 1800 x 1200 mm - Tool height: min. 750 mm - Maximum total tool weight: 50,000 kg - Tool upper part weight: max. 25,000 kg - Permissible load left/right: 800 kNm - Permissible load front/rear: 400 kNm - Includes industrial robot from manufacturer KUKA, year of manufacture: 2002 - Control system: SCHULER Collection: upon request FCA D-67227 Frankenthal - loaded onto a truck

Condition: excellent (used), Ifsys Type: 114100 Type: VL 13 Servo press Hopper system with 2 x Vibroliner and 2 x Vibrohopper Pjdpfx Ajzd Rk Esbgopu 1 x return conveyor belt 2 x control unit FC 1000 Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data are subject to change!) We will gladly answer any further questions you may have over the phone.

Condition: excellent (used), Here, we offer a TOX pressing machine, specifically the TOX-C bracket press. TOX Pressotechnik pressing machine, TOX-C bracket press. Pneumohydraulic manual workstation with process monitoring for pressing in functional elements. Technical data: Press type: EMB 030.068.Α.001 Drive: KWE3O.0O.17O.10H Pneumatic connection: G3/4'' Compressed air treatment: Filtered and dried compressed air, max. particle size 40 µm Air pressure during working process: Pmin. = 3.0 bar, Pmax. = 6.0 bar Pressing force: 170 kN Total stroke / return stroke: 170 mm / 10 mm Control: STE 326-366-3/4"-90-230V/AC special, complete Electrical connection: 90-230V/AC Ambient temperature during operation: Tmin. = 10°C, Tmax. = 60°C TOX pressing monitoring: EPW 500FP, force/travel measurement Holding device: ZHE for TOX press Dimensions: Width 1917.5 mm, Height 2506 mm, Depth 1917.5 mm Protective grid system: Leuze B20/B21 light curtain Pressing tool: See (pictures 15 to 18) Pressing sleeve (picture 17): 24.5 ∅ mm Application area, use: Pressing Weight: 2200 kg Type: EMB 030.068.A.001 Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data and specifications are subject to change!) We will gladly answer any further questions you may have over the phone. Podpfxezd Rhkj Abgepu