Used Testing Machine for sale (70,793)

Condition: used, SincoTec Type: Exciting Mot Resonance test bench POWER SWINGLY 20 kN The POWER SWINGLY BigTable resonance test bench is designed as a dual-mass vibrator. It consists of a vibration head, which is excited via an asynchronous motor with frequency control and an eccentric motor. The vibration head is located in the upper part of the machine and generates the dynamic amplitude. The vibration head is supported on the upper traverse via pre-tensioned coil springs and is guided centrally. The center load drive is located in the lower part of the machine and applies the static preload with the aid of a geared motor via a spindle drive. Itodpezii Awjfx Acpon The test chamber is located above the mounting table and is bounded upwards by the adjustable traverse. The control of the test bench is carried out by the EXCITING MOT control system. The complete control electronics for the control system are housed in an industrial PC cabinet. The control cabinet is made of powder-coated steel sheet and meets protection class IP 50 according to EN 60529. Technical data: General data of the test bench: Overall height of the test bench 1840 to 2240 mm Height of the machine table 1030 mm Width of the test bench 800 mm Depth of the test bench 1500 mm Height of the test chamber max. 600 mm (without force sensor) Free column passage 550 mm Maximum force amplitude 10000 N Maximum total force ±20000 N Maximum stroke ±5 mm Test frequency 30 to 110 Hz Accuracy of the measuring sensors min. class 1 (according to DIN EN 10002-3) Weight of the test bench approx. 1880 kg Max. weight of the clamping device 150 kg General data of the control cabinet: Overall height of the control cabinet 1900 mm Height of the table top 1080 mm Width of the control cabinet 650 mm Depth of the control cabinet 700 mm Weight of the control cabinet 152 kg Color RAI 9006 (white aluminum), table top Midnight Conditions for the installation site: Space requirement 2.5 x 2.5 m Required ceiling height 2.8 m Floor load-bearing capacity 170 N/cm² Voltage supply 400 V / 50 Hz (right-rotating field) Connection plug CEE socket, 5-pole, 16 A Fuse 16 A Connection and environmental conditions Mains conditions: Voltage 400 V three-phase with PE conductor and protective earth, right-rotating field Voltage fluctuations < ± 10% Short-time voltage dips < 20 ms Limits for permanent interference Radio interference level A according to VDE0871 Frequency 50 Hz ± 1% Protective earth Ground resistance < 0.3 Ω Model: POWER SWINGLY MOT Condition: used Scope of supply: (See picture) (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by telephone.

Condition: used, Zwick / Roell Universal testing machine / Material testing machine Zwick / Roell ProLine Z005 Universal Testing Machine 5 kN testing machine for tensile, compression, and material testing For sale is a used universal testing machine from the manufacturer Zwick / Roell. The machine is suitable for tensile tests, compression tests, material testing, component testing, quality assurance, research and development, and laboratory applications. Technical data Manufacturer: Zwick / Roell Type: ProLine Z005 / 5 kN ProLine Type of device: Universal testing machine / Material testing machine Year of manufacture: 2016 Made in Germany Maximum testing force: 5 kN Load cell: Zwick Xforce P Rated force of load cell: 5 kN Start of measurement, accuracy class 1: 20 N Start of measurement, accuracy class 0.5: 100 N Nominal measuring range: 0.06 mm Machine dimensions: approx. 917 x 439 x 1331 mm (W x D x H) Frame width: approx. 720 mm Installation width of frame: approx. 770 mm Testing space width: approx. 440 mm Machine weight: approx. 200 kg Weight of load cell: approx. 0.65 kg Mains connection: 230 V Frequency: 50 / 60 Hz Current consumption: 3.5 A Connection: 1L / PE / N Measuring module: DCSC Ijdpfszfy Ivjx Acpotn Measuring range: 0.2 % to 165 % of the nominal measuring value Measurement value acquisition rate: max. 10 kHz Measuring input: Differential input Sensor supply: 10 V DC Strain gauge bridge resistance: 175 to 1200 Ω Connection type: 4- and 6-conductor technology Nominal sensitivity: 2 mV/V Connection thread for load cell: M28 x 1.5 Connection bolt: Ø 20 mm Dowel pin: Ø 8 mm Degree of protection of load cell: IP54 Load cell Type: Xforce P Rated force: 5 kN Working force max.: 150 % of Fnom Limit force: 150 % of Fnom Breaking force: 300 % of Fnom Limit transverse force: 100 % of Fnom Component height: 95 mm Installation dimension: approx. 72 mm Installation height: approx. 61 mm Diameter: 54 mm Equipment Zwick / Roell ProLine testing frame Xforce P 5 kN load cell DCSC measuring module Electronic force measurement Machine electronics on the side of the load frame PC system / testing software as shown in the pictures Accessories as shown in the pictures Application areas Tensile testing Compression testing Material testing Material characterization Quality assurance Incoming goods inspection Research and development Laboratory applications Condition Used Optical condition as shown in the pictures Scope of delivery 1x Zwick / Roell ProLine Z005 Universal Testing Machine 1x Xforce P 5 kN Load Cell 1x DCSC Measuring Module PC system / Software as shown in the pictures Accessories as shown in the pictures The table shown in the photos, as well as any other items not explicitly mentioned, are not included in the sale. Shipping or forwarding possible. Subject to changes, errors and prior sale. We will gladly answer any further questions by telephone.

Year of construction: 2013, condition: good (used), Universal testing machine Zwick/roll Type: 1488 Modernized in 2013 with software Isdoxw N Uvepfx Acpstn Test force max.: 200 kN Required space: width: 2,000 mm, height: 2,100 mm, depth: 800 mm, weight approx. 1,000 kg.

Condition: ready for operation (used), throat depth: 150 mm, overall weight: 80 kg, Reicherter Stiefelmayer BRIRO VAK Hardness Tester, including VAT. Manufacturer: Reicherter Type: BRIRO VAK Outreach: approx. 150mm Max. test height: 250 - 300mm Ijdpfx Acsznh Nyspetn Weight: approx. 80 kg You are welcome to visit us for an inspection. We can also arrange cost-effective shipping for you! You will receive a proper invoice. For international customers, a net invoice can also be issued. A valid VAT identification number is required. Subject to prior sale. Visit our shop and view our other offers. The company names and trademarks mentioned are the property of their respective owners and are used only for identification and description of the products. Deviations from technical data as well as errors in the description of the article may occur and are subject to change.

Condition: used, Zwick / Roell Material Testing Machine / Universal Testing Machine Zwick / Roell Z020 Allround-Line BT2-FR020TNW.A50 20 kN material testing machine for tensile and compression testing with testControl II & testXpert V3.5 For sale is a used material testing machine from the manufacturer Zwick / Roell. The machine is suitable for tensile and compression tests on metals, plastics, elastomers, composite materials, Itjdpfx Acezra Rqepjn and numerous other materials in the laboratory, quality assurance, research and development. Technical data: Manufacturer: Zwick / Roell Model series: Z020 Allround-Line Type: BT2-FR020TNW.A50 Testing force: 20 kN Testing direction: Tensile & Compression Testing space height: 1000 mm Crosshead speed: 0.0005–1000 mm/min Power connection: 230 V / 50–60 Hz Power consumption: 8 A Electronics: testControl II Software: Zwick / Roell testXpert V3.5 Equipment: Servo-electric material testing machine testControl II control system Industrial PC with installed testXpert V3.5 software 20 kN Xforce P load cell 2.5 kN Xforce P load cell Testing table Test fixture Various connection and cable sets Accessories as shown in the pictures Dimensions and weight: Machine dimensions (approx.): 1244 × 690 × 1324 mm (W × D × H) Weight: approx. 212 kg Application areas: Tensile testing Compression testing Material testing Quality assurance Research & Development Testing laboratory Education and training Scope of supply: 1 × Zwick / Roell Z020 Allround-Line material testing machine testControl II control system Industrial PC with installed testXpert V3.5 software 20 kN Xforce P load cell 2.5 kN Xforce P load cell Connection and cable sets Further accessories as shown in the pictures Condition: Used Visual condition as shown in the pictures Functional scope as shown in the pictures Nameplates are present The table, monitor, keyboard, and mouse shown in the photos, as well as any other items not explicitly mentioned, are not part of the sale. Shipping or freight forwarding possible. Subject to change, errors and prior sale. We will be happy to answer any further questions by telephone.

Condition: good (used), Year of construction: 2024, A pre-owned Optos California ultra-widefield retinal imaging system, acquired in 2024, is supplied in its original Optos transport packaging. The complete system was purchased in 2024. Some individual components may have manufacture or procurement dates from 2023, which is normal for a multi-component system. Configuration: FA Iedjz Dq Stepfx Acpstn Model: California / P200DTx Manufacturer: Optos Condition: Pre-owned – used during a short clinical study The Optos California platform is designed for ultra-widefield retinal imaging and provides up to a 200° field of view in a single capture. This FA configuration supports fluorescein angiography in addition to the retinal imaging modalities available on the California platform. Included configuration: Scan head Touchscreen tablet & stand Image server with monitor Specialized device table OptosAdvance software Color & Red-free imaging Autofluorescence Fluorescein angiography The system is currently securely packed and palletized for transport. The shipment includes the Optos system and associated device table as shown in the image. Inspection is available by appointment. Worldwide shipping can be arranged.

Condition: ready for operation (used), Reicherter Stiefelmayer BRIRO R Hardness Tester, including VAT. Manufacturer: Reicherter Type: BRIRO R Outreach: approx. 150mm Max. test height: 240mm Weight: approx. 100 kg You are welcome to visit us for an inspection. Itedpfx Aoznh U Aocpen We can also arrange cost-effective shipping for you! You will receive a proper invoice. For foreign customers, a net invoice can also be issued. A valid VAT identification number is required. Subject to prior sale. Visit our shop and see our other offers. The company names and trademarks mentioned are the property of their respective owners and are used solely for identification and description of the products. Deviations in technical data and errors in the description of the article may occur and are subject to change.

Condition: excellent (used), Material Testing Machine / Universal Testing Machine Type: BT2-FZ1.0TN.D16.001 Base System: zwickiLine Z1.0 TN Special Torsion Multi-Axis Material Testing System 1 kN / 2 Nm Technical Data: Testing Range: Maximum axial testing force Fmax: 1 kN Configured maximum testing torque Mmax: 2 Nm Types of tests: Tensile, compressive, and torsional Axial drive / crosshead: Crosshead speed: 0.0005 to 2,000 mm/min Max. return speed: 2,000 mm/min Speed deviation: max. 0.05 % Path resolution: 0.0554 µm Positioning repeatability: ±2 µm Controller: adaptive Control cycle: 1,000 Hz Testing chamber: Testing chamber height with crosshead angled upwards: 235 to 1,065 mm Testing chamber height with crosshead angled downwards: 90 to 920 mm Testing chamber depth: 105 mm Dimensions of base machine: Height of load frame without head crosshead: approx. 1,289 mm Width with machine electronics: approx. 411 mm Depth with machine electronics: approx. 622 mm Weight of base machine: approx. 76 kg Type: Torsional drive Item No.: 1023835 Maximum drive torque: 20 Nm Rotational speed: 0.01 to 20 rpm Accuracy of set drive speed: 0.05 % Control cycle: 1,000 Hz Axially permissible testing force on the torsional drive: ±5 kN Power connection torsional drive: 230 V / 1 Ph / N / PE Mains frequency: 50 / 60 Hz Power consumption under full load: approx. 2.3 kVA Torque sensor: Item No.: 069536 Rated torque: 2 Nm Limit torque: 150 % of the rated torque Accuracy class 1 from: 0.008 Nm Accuracy class 0.5 from: 0.02 Nm Protection class: IP65 Force sensor: Type: Zwick / Roell Xforce HP Item No.: 069531 Rated force: 1 kN / 225 lbf Max. operating force: 150 % of Fnom Accuracy class 1 from: 2 N Accuracy class 0.5 from: 10 N Protection class: IP54 Measurement and control electronics: Zwick / Roell testControl II Measurement value acquisition rate: 400 kHz Measurement value transfer to PC: 500 Hz Optionally expandable to: 2,000 Hz Ijdpfx Aozwvtxecpstn Control cycle: 1,000 Hz PC interface: Ethernet Measurement signal runtime correction: for all channels Protection class electronics: IP32 Safety device: Swiveling front safety device Electrically monitored interlock Protective screen made of transparent polycarbonate Material thickness of protective screen: 6 mm Dimensions of safety device: Height: approx. 1,237 mm Width: approx. 435 mm Depth: approx. 238 mm Testing tools / accessories: Pneumatic universal holder for pen systems Max. clamping force: 200 N Compressed air supply: 8 bar, filtered and unlubricated Pneumatic 3-finger gripper Max. clamping force: 50 N Compressed air supply: 8 bar, filtered and unlubricated Alignment unit Torque sensor 2 Nm Xforce HP force sensor 1 kN Torsional drive Front safety device Zwick/Roell machine electronics Software: Zwick / Roell testXpert III testing softwareVersion: 1.2 + ALMEMO 2450 universal measuring device Humidity/temperature sensor FHAD4641 + Mettler Toledo precision balance Type: Mettler WXSE + Visual recognition system color Zwick Item No.: 3004644 Vision sensor: IV-G500CA Evaluation unit: IV-G10 Installation distance: 20 to 500 mm + Auto Injector Condition: used Optical condition according to the pictures Functionality according to the pictures The complete configuration of all components and accessories, as well as the calibration of the system, must be carried out by the customer themselves. Subject to changes, errors and prior sale.

Condition: excellent (used), functionality: fully functional, Universal testing machine for material testing / material analysis Testing of tensile strength, bond tensile strength, and shear strength of masonry and wood connections, etc. Isdpfoxmv H Rsx Acpstn - Nail pull-out test - Compression test on cement and mortar prisms - Bending test on cement and mortar specimens - Compaction test - Bending test on wood and concrete - Shear strength test on wood - Splitting test on wood - Scaffolding connection test - Shear strength test on walls - Tensile test on walls - Tensile test on structural steel - Tensile test on wood - Pull-out test on structural steel - Reversal bending test on structural steel - Anchor pull-out test - Bond tensile test I have made a video demonstrating the function of the testing machine. I can send this video to a mobile number via WhatsApp or Signal! Shipping and loading are possible at my warehouse!

Condition: good (used), Year of construction: 2013, operating hours: 300 h, functionality: fully functional, machine/vehicle number: H50KS, tractive force with load: 50,000 N, Universal testing machine, type H50kS up to 50KN for tension and compression Load cell 50KN 10KN 1KN and Windows software 8-9-10-or 11 for tension, compression, bending, shear etc., according to EN ISO 7500-1, ASTM E4 The H50kS is a universal testing machine developed according to the latest standards. The machine operates in accordance with the relevant radiation protection and safety directives in the EC. (EN 50081-1, 72/23/EEC, EN 61010-1) The maximum voltage within the machine is 48 volts. Special features - large, easy-to-read liquid crystal display with backlighting - Graphical or numerical display mode - alpha-numeric file input - speed range 0.001 to 500 mm/min. - high return speed 0.001 to 500 mm/min. - exact crosshead positioning - Robust load frame - Output report of results with mean value and standard deviation via printer - Large selection of test software under Windows for various standards - RS232 interface mode for use with computer system - Accuracy of load cell force display 0.5 % over the entire range - Displacement display accuracy 0.001 mm - Equipped with a force and displacement alarm system - 32bit motor controller - 20% digital weight blanking during load cell capacity check - Automatic motor alarm in case of over or under voltage and overheating Specifications: - Force measurement accuracy +/- 0.5 % of the displayed force in the range 2% to 100% - Accuracy of position measurement +/- 0.01 % or 0.001 mm - Speed accuracy +/- 0.005 % of the selected speed - Operating temperature 0 to 38°C - Humidity range 10% to 90% Technical data: - Two-spindle table model - maximum load 50kN in tension and compression - maximum stroke 1100 mm without clamping fixtures - for further details please refer to the brochure Itedpfxeq Ruw Ns Acpon Dimensions: Height: 1613 mm width: 720 mm Depth: 500 mm Weight: 140 kg Connection: Machine: 50-60 Hz - 2000 W Power supply: 220/240VAC

Condition: used, SincoTec Type: POWER SWING 20 kN POWER SWING 20 kN resonance testing system Sincotec Power Swing 20 kN resonance testing system Manufacturer's maintenance performed Itodpfxjzii A Do Acpon General information For sale is a used Power Swing 20 kN resonance testing system from Sincotec Test Systems GmbH. The testing system was used in a single-shift operation, and all maintenance work was performed regularly by the manufacturer. Special features: Robust construction for continuous operation Precise resonance testing up to 20 kN Manufacturer's maintenance available Ideal for research, testing, and development applications Technical data – Testing system Feature / Value Overall height of testing system 1215 mm (without clamping device) Width of testing system 2005 mm Depth of testing system 1205 mm Maximum force amplitude 10 kN Maximum total force ±20 kN Accuracy of measuring sensors min. Class 1 (according to DIN EN 10002-3) Technical data – Control cabinet Feature / Value Overall height of control cabinet approx. 1800 mm Height of tabletop 1080 mm Width of control cabinet 650 mm (narrow tabletop) / 1450 mm (wide tabletop) Depth of control cabinet 700 mm (narrow tabletop) / 800 mm (wide tabletop) Weight 152 kg (small tabletop) 187 kg (large tabletop) with (granite plate) 247 kg Conditions for the installation site Feature / Value Space requirement 4.3 × 3.0 m Required ceiling height 2.5 m Floor load-bearing capacity 234 N/cm² Mains conditions Feature / Value Voltage 400 V three-phase with neutral conductor and protective earth Phase sequence Right-rotating field Voltage fluctuations ≤ ±10 % Short-time dips < 20 ms Limits for sustained disturbances Radio interference level A according to VDE 0871 Frequency 50 Hz ± 1 % Protective earth / Grounding resistance < 0.3 Ω Connection and protection Feature / Value Voltage supply 400 V / 50 Hz (Right-rotating field) Connection plug CEE socket, 5-pole, 16 A Protection 16 A Weight of testing system approx. 3.6 t Max. weight clamping device 250 kg Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data are subject to change!) We would be happy to answer any further questions you may have by phone.

Condition: used, Zwick Type: Z30 Technical data: Overall height 2114 mm, width 748 mm, depth 580 mm Fmax: 30 kN Vmax: 125 mm/s Accessories: Extensometer ClipOn 13.5 mm Extensometer ClipOn 40 mm Computer + testXpert II V3.5 software Total weight approx. 500 Condition: used Itedpfx Aszil Ucscpen Scope of delivery: (See image) (Subject to changes and errors in the technical data and specifications!) We will gladly answer any further questions you may have over the phone.

Condition: used, Zwick / Roell Type: Z020 Allround-Line BT1-FR020TN.A50 Zwick / Roell Material Testing Machine, 20 kN, Tensile & Compression Testing, testXpert III For sale is a high-quality Zwick / Roell material testing machine for professional tensile and compression testing of materials and components. The machine is suitable for metals, plastics, rubber, and many other materials and is typically used in laboratories, quality assurance, research, and education. The machine is controlled via a PC with Zwick/Roell testXpert III software (storage medium and documentation available). Technical Data: Nominal testing force: 20 kN Testing direction: Tensile & Compression Power connection: 230 V / 50–60 Hz / 1-phase Power consumption: approx. 2.1 kVA Weight: approx. 150–180 kg Dimensions: approx. 856 × 650 × 1,545–2,114 mm Technical Data (from documents & nameplate) Mechanics / Testing Nominal force: 20 kN Testing direction: Tensile & Compression Max. testing frequency: 0.5 Hz Crosshead: servo-electric Positioning accuracy: < 1 µm Speed range: 0.0005 – 1,000 mm/min Dimensions & Weight Overall height: approx. 1,545 – 2,114 mm (depending on the crosshead position) Overall width: approx. 856 mm Overall depth: approx. 650 mm Working space width: 440 mm Weight: approx. 150 kg (basic unit) approx. 180 kg with typical equipment Electrical Data Power connection: 230 V AC Phases: 1-phase (1PH, N, PE) Mains frequency: 50 / 60 Hz Current consumption: approx. 8–10 A Itedpfx Acszimgtopsn Power consumption: approx. 2.1 kVA Socket: Schuko (CEE 7) Measuring & Control Electronics Internal measurement value acquisition: 500 Hz Data transmission to PC: 10–100 Hz adjustable Interface: RS232 (COM) Protection class for electronics housing: IP32 Important note: “The table shown in the photos is not included in the sale.” Condition: used Scope of supply: (See picture) Zwick / Roell material testing machine (20 kN) Electronics unit PC workstation (monitor, PC condition see pictures) 2 measuring modules (Delock units) Zwick/Roell testXpert III software (storage medium) Original operating and technical documentation Various connection and linking cables (Changes and errors in the technical data are subject to change!) We will gladly answer any further questions you may have by phone.

Condition: good (used), Year of construction: 2013, Traverses X Y Z: 1020 x 610 x 620mm, Table size 1200mm x 600mm, spindle speed 12000rpm, spindle motor power 14.7kW, Siemens 840DSL control with Shopmill, 43M/min rapids, Spindle taper BT40, Iodpfx Acez Eh Nlepotn 30 station ATC, through spindle coolant, swarf conveyor.

Condition: used, functionality: fully functional, Used tensile testing machine, model Zwick Z2.5 Zwicki, equipped with new control electronics and Windows-based PM-Soft-Smart software for tensile, compression, and bending tests up to 2.5 kN. The testing machine has been retrofitted with a new control unit featuring an MFC controller and can be operated exclusively via PC. Connection to a standard PC or laptop is established via a USB cable. The PM-Soft-Smart Windows software is a highly versatile control and evaluation software, allowing the user to create any number of custom test programs. The delivery also includes a test specification created according to customer requirements. Suitable grips for virtually all testing tasks are available as accessories. Technical data: Single-column testing machine incl. 2.5 kN load cell Crosshead travel: 800 mm Test space depth: 100 mm Displacement resolution: 0.0001 mm Iodpjykpamofx Acpetn Test speed: 0.2–1000 mm/min Power supply: 230V AC Dimensions (D x W x H): 414 x 320 x 1260 mm Weight: approx. 40 kg

Year of construction: 2005, condition: refurbished (used), We are offering this ZwickRoell 1484 200KN tensile and compression testing machine, manufactured in 2005, which has undergone a complete overhaul. Manufacturer: ZwickRoell Model: 1484 Year of manufacture: 2005 Condition: refurbished Itsdpfx Acjzw N Hlspsn Category ID: 407 Machine type: 200KN tensile and compression testing machine Types of tests: Tensile and/or compression Testing space: 2, top and bottom Capacity: 200KN Accessories: Included, in particular the mechanical grips The machine will be equipped with a new control cabinet with DOLI technology and testing software compliant with ISO 6892-1. If you have any questions or require further information, please do not hesitate to contact us.

Year of construction: 2023, condition: excellent (used), 1 used universal testing machine / tensile testing machine / material testing machine Manufacturer: Zwick Roell Type: Retroline 50 KN Modernization/inspection by ZwickRoell: 01/2023 Ijdoz Eyqnspfx Acpjtn with testControl II measuring, control, and regulating electronics. Maximum testing force: 50 kN 2 × wedge-type specimen holders, ZwickRoell 8404R, 50 kN Specimen holder part no. 1006757 Flat specimens: 0–22 mm, depending on the set of jaws Round specimens: Ø 4–19 mm, depending on the set of jaws Opening width with jaws: 22 mm Connecting pin: Ø 36 mm Weight per specimen holder: approx. 11 kg suitable for static and cyclic tensile tests extensive original ZwickRoell documentation inspection report available very well-maintained condition Application areas: Tensile tests and material testing on metals, plastics, and other materials; suitable for quality assurance, testing laboratories, research, development, and training.

Condition: used, Zwick Testing Machine Type: Z20 Controller: BX1-EZ020.A4K-000 Technical Data: Stroke: 200 mm Piston dimensions H x W x D: 1037 x 385 x 180 mm Fmax: 20 kN Vmax: 125 mm/s Accessories: ClipOn extensometer, 13.5 mm MFA 25 extensometer (temperature range up to +200°C) Computer + testXpert II V3.5 software Climate chamber: Airtemp LKG-K-TK-50 Temperature range: -40°C to +150°C Climate temperature range: 20°C to +90°C Humidity range: 10% to 95% Ijdpfx Ajzil Upecpetn Test chamber volume: 50 liters Temperature change rate: 1 K/min Refrigerant: R404, 5 kg Voltage: 400V 3Ph/N/PE/50 Hz 16 A 9 kW Condition: used Total weight: approx. 1500 kg Scope of delivery: (See image) (Subject to changes and errors in the technical data and specifications!) We will be happy to answer any further questions you may have by phone. Written orders can be placed by email or fax.

Condition: used, functionality: fully functional, Rotary testing machine for testing transformers 8 stations Testing stations for: voltage, input/output current (mA), high voltage, pad printing Itjdpsyl Adzefx Acpen Test adapters for all common EI transformers included

Condition: excellent (used), Year of construction: 2022, 400mm swing, 220mm max diameter, 510mm cutting length, Siemens 828 Control, 65mm bar capacity, 12 station turret, 17kW Spindle Motor, Spindle Speed 4000rpm, Ijdpfx Asz Hatfscpetn 3 jaw chuck, low volt light, coolant, Tool setter, swarf conveyor

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: PM3, Universal testing machine PM3 (2026) Force: 3 kN Crosshead travel: 520 mm Working space depth: 66 mm Overall height: 1036 mm Weight: approx. 40 kg Displacement resolution: 0.01 mm Testing speed: 1-500 mm/min Cc7d2rmq Return speed: 700 mm/min Ijdoyc U Dbjpfx Acpstn Load cell: 3 kN Includes evaluation electronics and basic software. Our testing machines can be operated in stand-alone mode via a numeric keypad, allowing for a “quick test” even without a PC. For tests that require data storage and recording of the curve profile, we offer the option to control and evaluate the tests using the basic software. This allows you to generate various test sequences and create a test report. Furthermore, you have the option to process the raw data in your own programs. Optional: - Delivery and commissioning - DAkkS or factory calibration according to DIN EN ISO 7500-1 - Clamping devices: Pressure plates, bending fixtures, shear fixtures, wedge clamps, scissor clamps, peeling clamps, screw clamps, pneumatic clamps, and hydraulic clamps.

Condition: used, machine/vehicle number: 5585HK1182, We are offering this used Instron 5585HK1182 universal testing machine for sale. Stroke: 1182 mm Iedpfx Aezgv Etocpetn Pressing force: 25 t Dimensions (installation): 1.5 x 1.0 x 2.5 m Weight: 952 kg Control system: Instron Blue Hill If you have any questions or require further information, please do not hesitate to contact us.

Condition: excellent (used), Year of construction: 1992, functionality: fully functional, machine/vehicle number: 06651, travel distance X-axis: 6,800 mm, travel distance Y-axis: 3,700 mm, travel distance Z-axis: 1,500 mm, feed rate X-axis: 15 m/min, feed rate Y-axis: 15 m/min, feed rate Z-axis: 10 m/min, total length: 15,000 mm, total width: 7,500 mm, spindle speed (max.): 4,000 rpm, total height: 7,000 mm, table height: 1,100 mm, rapid traverse X-axis: 15 m/min, rapid traverse Y-axis: 15 m/min, rapid traverse Z-axis: 10 m/min, distance between stands: 3,300 mm, type of input current: three-phase, table load: 50,000 kg, rotational speed (max.): 4,000 rpm, distance table center to spindle nose: 2,110 mm, overall weight: 110,000 kg, spindle motor power: 50,000 W, control cabinet length: 7,000 mm, control cabinet height: 2,000 mm, control cabinet width: 600 mm, Equipment: rotational speed infinitely variable, MODEL: Portal Type AGE: 1992 S/N #: 06651 CATEGORY: Mills, Planer Type, CNC CAPACITY: X-Axis Travel: 6800 mm Y-Axis Head Travel: 3700 mm Z-Axis Ram Stroke: 1500 mm, fixed crossrail Ram Cross Section: 500 mm x 500 mm Distance Between Columns: 3300 mm Distance Table To Ram Face: 2110 mm, vertical passage 2000 mm Table Size: 6000 x 2500 mm Spindle (Quill) Diameter: 250 mm Spindle Taper: ISO #50 Spindle Speeds: 0-4000 RPM Ijdeyahv Sjpfx Acpjtn Spindle Motor: 50 KW EQUIPPED WITH: FIDIA System C20 CNC Control, new in 2002 CNC biaxial continous milling head Universal Milling Head with Auto Indexing Right Angle Head with Auto Indexing Straight Milling Head Wagons for Head Change and Tool Pick-up Change Hydrostatic Bearings Coolant System Full Length Chip Conveyors both side Way Covers Rapid movements: Z-10.000 mm/min, X and Y-15.000 mm/min Table load: max 50.000 kg Weight of the machine: 110.000 kg Outside dimensions: 15.000 x 7.500 x 7050 mm Machine has been tested before dismantling and is fully operational, all mechanical components in excellent condition, electrics new in 2018. Machine available from stock. The price is now SPECIAL FROM STOCK. Once we will reassemble the machine, price will grow significantly. We can assist you to assemble and run up the machine.

Condition: used, Zwick Type: HA 50 Dimensions: H 2685 mm x W 1040 mm x D 750 mm Footprint: 1600 cm² Technical data: Fmax: 50 kN Vmax: 1500 mm/s Working area height max. 1370 mm Working area width 565 mm Accessories: Kistler force sensor 50 kN via NI-Labview Hydraulic unit 280 bar Footprint: 415 cm² Clamping device / specimen holder available (Universal flange, high-strength jaws for specimen holder) Computer + testXpert R V6.0.0 software Condition: used Iedpfxjzil Uie Acpetn Scope of delivery: (See image) Weight approx. 1200 kg without frame, etc. (Changes and errors in the technical data are subject to change!) We will gladly answer any further questions you may have by phone.

Condition: used, Zwick / Roell Type: LTM10 Max. testing frequency: 100 Hz, depending on the amplitude Dynamic testing force in tension/compression: 10 kN Static testing force in tension/compression: 7 kN Piston stroke: 60 mm Positioning and repeat accuracy: +/- 2 µm Speed range: 1 mm/min - 1 m/s Testing space height without load cell: 1170 mm Weight with linear motor: 1065 kg (without control unit) Maintenance: according to maintenance specifications, partially performed by Zwick/Roell Accessories: screw chucks, software (TestXpert research) Isdpfx Acjzh D R Hepetn Connection: 400V 50/60 Hz 32A 3-phase/PE Condition: used Scope of delivery: (See image) (Changes and errors in the technical data are subject to change!) We will gladly answer any further questions you may have over the phone.