Center lathe

Padovani Labor 275 E Electronic Teachin

Condition: used, Year of construction: 1979, functionality: fully functional, Swing over bed 2000mm Swing over carriage 1700mm Turning lenght 8000mm Max. weight of workpiece in centers 80 ton Max. weight of workpiece in centers and steadies 100 ton Main motor power 150kW Spindle speed (3 ranges) 0,5-160rpm 4-jaws independent chuck dia. 1700mm Min. clamping dia. 170mm Hjdpfxoyy Nx Ns Ahaet Max. clamping dia. 1400mm Dia. of tailstock quill 450mm Bed width 2280mm Height of bed 650mm Special equipment: - 4-jaws chuck dia. 1700mm - tool system: double shelf toolpost - steady rest dia. 200-600mm - steady rest dia. 600-1100mm - open steady rest up to 1600mm Total weight of the lathe 110 tons

Condition: excellent (used), turning diameter over bed 900 mm turning diameter over slide rest 600 mm turning length 3000 mm spindle turning speed range 11,2 - 560 U/min tool holder Multifix D1 total power requirement 22 kW weight of the machine ca. 5,6 t dimensions of the machine ca. 5,6 x 1,8 x 1,7 m Safety-related conversion according to CE standard 2017 2011 new plan pull spindle, lock case partially renewed, lubrication according Hedpfx Ahjym D H Teaet to internal plan

Year of construction: 2024, condition: new, Motorized sheet metal shear Technical data Cutting capacity: 2.5 mm Cutting length: 2550 mm Cutting angle: 1°40′ Stroke rate/min: 35 1/sec Motor power: 3 kW Hedpfx Ashk Nf Rehajt Back gauge range: 550 mm Table width: 400 mm Table height: 850 mm Height: 1260 mm Width: 1350 mm Length: 3100 mm Weight approx.: 1540 kg

Condition: used, Wig welding machine L-TEC, Inverter TIG 200 DC type WIG welding machine for direct current DC Serial no. 184548, year of manufacture approx. 1994 Power: 200 Amps = 60% duty cycle 155 Amps = 100% duty cycle Adjustment range: stepless Current type: DC (direct current) Mains connection: 400 Volts, 50 Hz, 32 Amps plug - 4 meter hose set with central connection and hand torch - with remote potentiometer (foot switch) Hsdpsdzqb Eofx Ahaot - gas pressure regulator - DC only - HF ignition Space requirement L x W x H: 850 x 480 x 740 mm Weight: approx. 150 kg The welding test yields very good results when welding stainless steel with direct current. Otherwise in good condition.

Condition: new, Year of construction: 2026, The CORMAK HBS275 band saw for cutting tubes, profiles and bars is widely used in all locksmith and metalworking workshops where precision, quality and cutting speed matter. The model is equipped with a 0-60° swivel arm; the saw guides are based on sintered carbide. The frame construction ensures accurate and quiet operation. Machine characteristics The horizontal metal band saw with swivel arm enables cutting in a plane perpendicular to the axis of the material being cut and at any angle within the range from 0 to 60°. The material to be cut can be fed manually or by any mechanical device, while the tool feed is automatic. The blade guides are equipped with special carbide plates and bearings. This has a major impact on blade guidance, service life, straightness, accuracy and cutting quality. Carbide guidance greatly reduces wear of the machine and blade. The machine is equipped with an efficient coolant pump with a closed coolant circuit. The saw arm is made of a single cast-iron casting and, together with the 27 mm wide cutting blade used in this saw, fully enables multi-series cutting of both profiles and solid materials. The vice is located in an adjustable bed and is equipped with a quick clamp. The blade guides are equipped with hard metal plates – sintered carbide and a rolling bearing system. It is precisely the SINTERED CARBIDE GUIDES that are responsible for the precision and straightness of the cut. The arm has been inclined at an angle of 25°, which increases blade durability and improves cutting conditions. A cleaning brush is mounted at the bottom of the arm to achieve excellent cleanliness and blade operation. The machine drive is transmitted via a worm gearbox. The machine has a three-phase motor with two cutting speeds and motor thermal protection. The shape of the upper part of the base forms a tray for draining coolant and collecting chips generated during material cutting. A cast-iron work table with a swivel arm and a control panel on a separate arm is mounted to the base. In the cutting process, the main cutting movement is the movement of the cutting blade, while the feed is the lowering of the arm. The arm lowering speed (cutting speed) is regulated by a hydraulic cylinder. The feed speed is adjusted on the saw control panel. Two cutting blade speeds are available: 37.5 and 75m/min. In the lower position of the arm (after cutting the material), the cutting blade drive is switched off automatically. Safety is ensured by cutting blade guards and micro-switches that stop the motor after the cutting cycle is completed or when any guard is opened; additional protection consists of automatic shutdown of the saw in the event of cutting blade breakage. The machine drive is transmitted by a motor with a worm gearbox. The motor with thermal fuse protects against overheating during operation. Technical data TOTAL POWER 1.5kW POWER SUPPLY 400V 50Hz ARM LOWERING ADJUSTMENT hydraulic cylinder BLADE LENGTH 2450 x 27 x 0.9 mm Hsdpfeudi Unox Ahaet BLADE SPEED 37.5 / 75m/min VICE BASE HEIGHT 900 mm MACHINE DIMENSIONS (WITH ARM RAISED) (L x W x H) 1720 x 800 x 1800 mm WEIGHT 215 kg

Year of construction: 1972, condition: ready for operation (used), Spindle-to-table distance min./max.: 81mm/481mm, counter support spindle center distance: 195mm, spindle head swivel: 360°, milling spindle diameter: 70mm, spindle adjustment: 100mm, headstock adjustment: 300mm, table dimensions X/Y: 480mm/820mm, travel X/Y/Z: 500mm/200mm/400mm, max. workpiece length: 400mm, spindle speed: 1600rpm, feed X/Y: 500mm/min, feed Z: 250mm/min, spindle head swivel: +/-30°, machine dimensions X/Y/Z: approx. 1600mm/2550mm/1700mm, weight: approx. 2300kg. The machine was electrically tested at the end of 2025 and a defect of the emergency stop switch was discovered. Documentation available. On-site inspection is possible. Hjdpfx Ajx S Rcmjhaet

Condition: good (used), Year of construction: 1980, turning diameter over bed slide: 1,040 mm, turning diameter over top slide: 710 mm, turning length: 2,000 mm, bed width: 600 mm, Optional chuck 1200 mm 2 Axis RSF Digital read out Conical turning attachment Spindle bore 130 mm Central lubrication DBC Turning Length: 2000mm Swing over bed Ø: 1040mm Swing over cross slide Ø:710mm Swing in the gap Ø: 1780mm Gap length: 1000mm Spindle bore: 130mm Bed width: 600mm Tailstock spindle Ø: 130Ø Stroke pinole: 300mm Hodpfx Ajx Tgr Tohast Spindle taper: 6Mk Power: 22kW Speeds / ranges: 600Rpm Feed rate X-Axis: 4000mm/min. Feed rate Z-Axis: 4000mm/min. Length: 6000mm Width: 2100mm Height: 2100mm Weight: 8300kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: ready for operation (used), Year of construction: 2012, A Mitutoyo coordinate measuring machine overhauled in 2023 is available. Measuring dimensions X/Y/Z: 705mm/1005mm/605mm, max. workpiece height: 800mm, table dimensions X/Y: 880mm/1720mm, max. table load: 1000kg, resolution: 0.1µm, traverse speed: 520mm/s, measuring speed: 8mm/s. Machine dimensions X/Y/Z: approx. 1500mm/2000mm/2750mm, weight: approx. 2000kg, control: GEOPAK and CAT 1000 PS. Including various probe trees. Documentation available. On-site inspection is possible. Hjdpex Ih A Njfx Ahast

Condition: good (used), Year of construction: 2011, machine/vehicle number: 2212.287, Automatic panelsaw Schelling Typ:FH 6 430 Maskin nr:221.287 År:2011 Panel beam saw Schelling with automatic, rear-feed,lifting table. For sawing board material, chipboard, MDF, Plywood, Board, Laminate etc. Techn info: Software MCS Evolution 2.0, SPS, Soft-SPS-Siemens WinAC Operating system WINDOWS XP PC with keyboard and mouse TFT monitor 17" Cutting length 4300mm, automatic detection of the start of the plate Cutting width 4300mm Machine accuracy of the cut length 3m +-0.1mm Positioning accuracy measured at input +-0.1mm Hedpfx Ahstk It Soaot Max diameter saw blade 460mm, spindle 30mm Pre-scoring blade 200mm, spindle 20mm motor operation is set from the control console Max panel thickness 120mm Panel stack aligner Main saw blade motor 27kw Saw blade over table 135mm Safety curtain Air cushion table with 3pcs air ball nozzles, radial ventilator fan Table sizes 2650x850mm 620x850mm 2650x2550mm Pressure beam with automatic adjustment of pressure to cut length and package height Package straightener before and after the pressure beam Max package height 120mm (incl. sum of curvature and board thickness tolerance) Pusher with 12 grippers Max clamp opening (gripper) 133mm Min-max force package straightener 400/2000N Speed saw carriage forward 6-150m/min Speed saw carriage back 150m/min Forward feed speed (pusher) up to 25m/min (according to EC Europa EN1870-13) other countries 80m/min Speed feeding back up to 80m/min Push-off device 3 pcs Lift table length x width 4350x2550mm Hydraulic unit Standard version 1600mm lifting height 1.25/2.5m/min raising speed, 1.25/5m/min lowering speed Maximum load 1200 kg/m2 total 9 tons Roller track driven rollers, frequency controlled for stack on lifting table 4100x2600mm Max stack weight 6500 kg Max stack length 1060mm Slots for forklift 4 pcs, distance in the middle 1200mm, slot width 300mm Light curtain for personal protection Roller conveyor driven for package frequency controlled input to lifting table left 5600x2600mm max load 6500kg Roller conveyor driven for packages frequency controlled input to lifting table right 5600x2600mm max load 6500kg Slots for forklift 2 pcs, center distance 900mm, slot width 400mm 2 positioning stops with roller for stack alignment Light curtain (double beam) for personal protection Roller table after saw depth 4300mm, free-running ployamide rollers Angle stop at the rolling table Infeed guide two-lane (beam length 7200mm) 2-sided hardened precision guides rack and pinion drive, two-sided Input carriage (pusher) gear rack servo drive, non-contact measuring system Gripper, (scissor clamps) in pusher 12 pcs Automatic adaptation of the clamping force to the package height (progressive clamping force) can be set to 0 Pusher for panels thickness greater than 6mm,material thinner than 6mm is fed manually Central cleaning system feed trough (pusher) Compressed air 6-8 bar, approx. 1600l/min Power 38 kw, 70 A. 3x400 volts, 50 Hz, operating voltage 24 VDC Dust extraction 4000m/h, air speed 30m/s Diameter connection 80mm (angle connection), 120mm /pressure beam), 150mm (sawdust channel) Total setup area without driven roller conveyors including protective grid approx: 11650x7300mm Driven roller tracks left-right 5500+5500mm Stock no: 2002125BXACEO Subject to incorrect technical data presented

Condition: refurbished (used), ECCENTRIC PRESS SGP TYPE : PEZZ 500/1700/1000 PRESSURE : 500t DOWN TABLE DIMENSIONS: 1700x1000mm Hodjhqqnzspfx Ahaot LENGTH OF STROKE: 20-153mm DISTANCE BETWEEN RAM -TABLE: Min 700mm , Max 800mm WEIGHT: 40.000 kgr MADE IN AUSTRIA