Roll Grinder

WaldrichSiegen WSF 400

Condition: good (used), Year of construction: 1995, functionality: fully functional, turning diameter over cross slide: 267 mm, spindle bore: 76 mm, center height: 228 mm, center width: 1,500 mm, quill stroke: 229 mm, quill diameter: 75 mm, total length: 3,030 mm, total width: 1,200 mm, total height: 2,000 mm, rotational speed (max.): 1,600 rpm, rotational speed (min.): 20 rpm, overall weight: 2,300 kg, Conventional lathe, center high 228 mm, between centers 1500 mm, bore Ø 76 mm, 16 speed 20 - 1600 rpm, motor 9,3 kw, camlock 8'', dimensions 310x120x200 cm, weight ca. 2300 kgs; equipement: pneumatic chuck SCHUNK ROTA Ø 315 mm, coolant device, 3-jaws chuck Ø 315 mm, several jaws, live center, tool post PARAT WD with toolholders, steady rest, drilling chuck, lamp, manual, cabinet Gujdpfjypud Ujx An Iog

Condition: good (used), Year of construction: 1980, turning diameter over bed slide: 1,040 mm, turning diameter over top slide: 710 mm, turning length: 2,000 mm, bed width: 600 mm, Optional chuck 1200 mm 2 Axis RSF Digital read out Conical turning attachment Spindle bore 130 mm Central lubrication DBC Turning Length: 2000mm Swing over bed Ø: 1040mm Gsdpfx Ajx Tgr Tjn Ijug Swing over cross slide Ø:710mm Swing in the gap Ø: 1780mm Gap length: 1000mm Spindle bore: 130mm Bed width: 600mm Tailstock spindle Ø: 130Ø Stroke pinole: 300mm Spindle taper: 6Mk Power: 22kW Speeds / ranges: 600Rpm Feed rate X-Axis: 4000mm/min. Feed rate Z-Axis: 4000mm/min. Length: 6000mm Width: 2100mm Height: 2100mm Weight: 8300kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: new, functionality: fully functional, Year of construction: 2025, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, dust extraction, emergency stop, fume extraction, nozzle changer, safety light barrier, High-strength welding bed Guodsw A Iilopfx An Iog Partitioned smoke extraction system Fully automatic butter injection system Fully automatic cutting, material saving, fast speed Cutting area 4000 × 2000 mm X‑axis travel 1520 mm Y‑axis travel 4020 mm Z‑axis travel 80 mm Max. combined positioning speed 170 m/min Acceleration 2.8 G Machine dimensions (L×W×H) 9500 × 2900 × 2380 mm Footprint 10500 × 3400 mm Net weight 8500 kg

Condition: new, maximum load weight: 67,200 kg, overall weight: 85,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Full specifications available upon request. GOOSENECK * Gooseneck in SNT design to optimize load floor length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractors: 6 x 2, 6 x 4, and short 8 x 4 * Detachable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic power unit for controlling hydraulic functions, except for hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of flat lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in aluminum side boards, approx. 400 mm high, anodized * 1 plug-in aluminum rear board, approx. 400 mm high, anodized * Approx. 40 mm thick hardwood flooring above gooseneck, checker plate flooring above kingpin * 3.5 inch kingpin * Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow regulator, including bracket for hanging supply lines (Faymonville couplers) * 2 pairs of stake pockets recessed in the gooseneck, for plug-in stakes approx. 100 x 50 mm LOAD FLOOR * Extendable load floor, approx. 11,000 mm long, with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical locking bolts and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective deck length * BPW axles and suspension, 1st axle steered, 2nd axle fixed, all other axles hydro-mechanically forced steered * 1st axle with electro-magnetic reverse lock via reverse gear and manual activation * Axle load capacity: 12,000 kg each * Air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing gears with 2-speed gearbox and crank. JOST Modul B – static test load = approx. 50,000 kg * Continuous and, between axles, interrupted approx. 50 mm thick hardwood floor on load deck (increases coefficient of friction) * Slotted holes for attachable and repositionable bridging elements: – at the fixed part behind the gooseneck – on the front of the load floor * 1 sliding intermediate table, approx. 500 mm wide, for the sliding tube with large cross-section, checker plate flooring, front and rear with slotted holes for attachable and repositionable bridging elements * 1 pair of recessed flat lashing rings in the front fixed part of the load floor (LC 10,000 daN) * 9 pairs of recessed lashing rings, foldable outward, in the load floor perimeter frame (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking control, no installation required in the tractor * 1st axle with automatic lift axle function and start-up assist according to EU Regulation 2021/535 Gujdpfxergzv Ne An Ijg * Under the gooseneck and at the rear cross member, left and right, a 7-pin socket each with holder for warning signs * Factory-applied sand coating on the perimeter frame of the load floor as well as the checker plates and the transition area between load decks

Condition: as good as new (ex-display), Demo device with less than 20 operating hours // BEST CONDITION System: Optiv M 6.6.4 multi-sensor coordinate measuring machine with Dual Z technology Probes and sensors: - 10x CNC motor zoom with digital color camera and 12-segment LED ring light - HPsS-X1H Scanning Sensor with HH-A-T5 - HP-S-X1C/H stylus holder (1xM3) - M3 stylus kit for HP-S-X1C sensor - HR-X button rack for HP-S-X1C/H (3 ports, L=400) - Sensor calibration unit without calibration artifacts - Glass standard 25mm - Ring gauge 20mm Computers and software: - Measurement and evaluation software PC-DMIS CAD++ - Machine control unit BEST - Dell 27" monitor - work table Optional accessories: - Chromatic white light sensor (CWS) - CWS measuring head 3mm - Solara.MP12 - QA STAT 12 Gujdpfsncfd Rjx An Isg - O-QIS 12 Delivery, commissioning and other services on request If desired, the measuring device can be converted from OptiCheck3D V 5.0

Year of construction: 1981, condition: excellent (used), faceplate diam 1300mm max turning diam 1100mm Gedpfx Anjk Dz N Ij Isug range of turning diam 460-1250mm

Condition: excellent (used), Year of construction: 2015, functionality: fully functional, Equipment: documentation/manual, Machine model: ALC400G Max. workpiece dimensions (W×D×H): 600 × 470 × 240 mm (Flushing) Max. workpiece dimensions (W×D×H): 600 × 470 × 230 mm (Submerged) Max. workpiece weight: 500 kg (Flushing) Max. workpiece weight: 350 kg (Submerged) Gedpfxsyu Nqme An Isug Work tank dimensions (W×D): 850 × 610 mm X axis travel: 400 mm Y axis travel: 300 mm Z axis travel: 250 mm U axis travel: 150 mm V axis travel: 150 mm Taper angle (at workpiece thickness 130 mm): ±25° Wire diameter: Ø0.1 – Ø0.3 mm Wire feed speed (max): 420 mm/sec Wire tension: 3 – 23 N Machining method: Flushing / Submerged Distance from floor to table top: 995 mm Wire bobbin weight: 8 kg Machine dimensions (W×D×H): 2,115 × 2,500 × 2,230 mm Machine installation space (W×D): 3,350 × 3,850 mm Machine weight (including power supply): 3,400 kg Air pressure: 0.5 MPa Air consumption: 30 NL/min Total power input: 3-phase, 50/60 Hz, 13 kVA Dielectric tank external dimensions (W×D): 700 × 2,155 mm Dielectric tank weight (empty): 450 kg Dielectric tank capacity: 675 liters Dielectric fluid filtration method: 3 replaceable paper filters (internal pressure type) Deionizer: Ion-exchange resin (18 L type)

Condition: used, Year of construction: 2010, operating hours: 11,780 h, Equipment: ABS, all wheel drive, Volvo EXCAVATOR EW140C air conditioning 16,850 kg Gusdpfx Ansyltr Ao Isg 91 kW Top condition

Condition: used, Year of construction: 1973, pressure 200 t chamfer lenght 3600 mm distance between columns 2650 mm dayligth 500 mm throat 300 mm stroke 250 mm working feed 10,5 mm/sec return speed 100 mm/sec ram stroke speed 150 mm/sec table height 900 mm oil volume 500 l Gusdpfxot I D U Ee An Iog total power requirement 37 kW weight of the machine ca. 17800 kg dimensions of the machine ca. 3710 x 1800 x 3390 mm Equipment: - Controlled axes Y1 + Y2 - Manual X-axis with digital position display - Set of upper and lower tools - 2x stop fingers - 2x front support arms - Hand and foot controls - Side + rear safety guard - Operating instructions

Condition: good (used), Year of construction: 2012, Vertical CNC turning machine with a 12-position turret and powered tools; Year of manufacture 2012, in good condition; Fanuc 31i control system with Manual Guide i; 630 chuck – 900 mm turning diameter; Automatic door; 2-stage gearbox – resulting in very high torque; Tool setter, detachable; Chip conveyor; Various tool holders, fixed and powered; Only approximately 4,100 operating hours. An inspection is possible and recommended by arrangement, with the machine powered on. Gedpfx Aneztqp Hj Ieug