Lead/traction spindle lathe

WEILER Condor 81

Condition: used, L + Z Lathe WEILER Type Condor 81 A Mach. No. 36553 Year of manufacture approx. 1985 Centre distance 750 mm Swing over bed 330 mm Centre height over bed 165 mm Swing over cross slide 180 mm Centre height over cross slide 90 mm Spindle bore 40 mm Chuck mounting: Short taper DIN 55027 size 5 Tailstock quill taper MK 3 Quill travel 110 mm Spindle speed 45 - 2800 rpm, 16 steps Drive power 3 kW Power supply 400 Volt, 50 Hz - Spindle speed through 16 gear steps - 3-jaw chuck Ø 160 mm RÖHM with hard and soft jaws Kdjdjk S Ht Aopfx Apdjl - Multifix quick-change tool post size B with 3 holders - Automatic longitudinal and cross feed - Electro-mechanical spindle brake - Emergency stop - Coolant tank with pump integrated in the machine base, without feed hose to working area - Hinged chuck guard - Splash guard - 1 live center - Electric diagram and operating manual Space requirements L x W x H 1850 x 950 x 1400 mm Weight 1100 kg Good condition

Condition: used, Year of construction: 1987, pressure / t stroke / mm table-size / mm weight of the machine ca. 65000 kg Make: Shepherd Type: SVRM 4-roller bending machine: Year of construction: 1986 Working width: 3000cm Smallest pipe diameter with 600 mm roller: Ø 720 mm Smallest tube diameter with 360 mm roller: Ø 460 mm Kedpfxjuddcaj Apdjdl Sheet thickness up to (depending on the material): 50 mm Material SA- 738 B Working width: 2500 mm Material SA- 738 B Material thickness: 35 mm conical bending: Except for the top roller, all rollers can be moved in an inclined position for conical bending. The roller positions can be read on display instruments. For semi-automatic or fully automatic operation of the machine, the bearing jewels of the rollers are equipped with scale bars and slide cams for limit switch actuation. This allows the rollers to return to the same set position over and over again, giving a very high level of uniformity in the shot wefts being bent.

Condition: excellent (used), Year of construction: 1987, functionality: fully functional, Weiler Centre Lathe Model Condor 81 Lead and Feed Screw Lathe with 3-Axis Heidenhain Digital Readout from a Training Workshop Technical Data: >> Year of manufacture: 1987 / Machine No.: 87-674 >> Centre height: 165 mm >> Distance between centres: 750 mm >> Spindle speeds: 22 to 2800 rpm Kdsdpfoym Slwex Apdsl >> Spindle bore: 40 mm >> Camlock Spindle Nose DIN 55027 Size 5 with bayonet lock >> Tailstock taper: MT 3 >> Feeds: 0.015 to 0.46 mm/rev >> Thread cutting capability: metric, inch, module, and diametral pitch >> Metric thread pitches: 0.18 to 28 mm >> Spindle brake >> Weight: approx. 1,100 kg >> Switchable spindle brake >> Dimensions (LxHxD): 1.83 m x 1.29 m x 0.88 m Included Accessories and Equipment: >> 3-axis Heidenhain digital readout >> 1 pc. 3-jaw chuck with one set of jaws (wedge type) >> Quick collet change system with collets from 1–29 mm in 0.5 mm increments >> Toolholder with 7 tool pockets >> Bed stop >> Machine feet >> Drill chuck >> Live centre >> Coolant system About the Machine: Offered here is a used Weiler Condor 81 lathe, year 1987, in very good condition. The machine is, of course, fully functional. It is a very robust and powerful machine. Coming from a training workshop, the Weiler is extremely well maintained. The 3-axis Heidenhain digital readout allows for easier and more precise operation. The machine has been electrically and mechanically inspected by us. A complete oil change has been performed. This newer generation of Weiler lathes is very user-friendly. Take the opportunity to view and test the machine under power on site.

Condition: good (used), functionality: fully functional, Used L + Z lathe with 3-axis digital readout Manufacturer: WEILER Type: Condor 81 B Machine. No.: 87596 Year of manufacture: approx. 1987 Center distance: 750 mm Turning diameter over bed: Ø 330 mm Center height above bed: 165 mm Turning diameter over support: Ø 180 mm Center height above support: 90 mm Spindle bore: Ø 40 mm Tailstock inner taper: MK 3 Pinol adjustment: 110 mm Spindle speed: 45 - 2800 rpm. (16 steps + 2 motor speeds) Feed range: 0.016 - 0.50 mm/rev Drive power: 1.6 + 3.2 kW (drive motor stage 1+2) Mains connection: 400 Volt, 50 Hz Connected load: 32 kW Control voltage: 42 Volt Equipment + accessories: - 3-axis digital readout from Heidenhain type VRZ 750 Kdjdpfx Apsvadqzedol - Quick clamping device and various collets + draw tube - 3-jaw power chuck Ø 160 mm Forkardt F160 - Multifix size B quick-change steel holder - LED work light - Bed stop - Automatic longitudinal & face feeds - Electro-mechanical spindle brake switchable - 2x emergency stop - Electrical feed key query (via sleeve with button) - Coolant tank with pump in the machine base - Folding chuck guard - Splash guard - Circuit diagram - Adjustable machine feet Space requirement: 1850 x 950 x 1400 mm (L x W x H) Weight: approx. 1100 kg This new generation of Weiler lathes is very user-friendly and robust. Machine can be demonstrated on site under power. All information without guarantee. Subject to prior sale.

Condition: used, Technical details: x-travel: 700 mm y-travel: 450 mm z-travel: 450 mm spindle cone ISO: 40 (SK 40) table surface area: 760 x 420 mm table feed: längs: 10 - 500 (Eilgang: 1,4 m/min.) mm/min table feed: vertical: 5 - 250 (Eilgang: 1,4 m/min.) mm/min spindle turning speed - continuous: 32 - 1600 / 18 step U/min spindle head swivable left - right: 10 ° links / rechts ° quill stroke vertical: 125 mm feed continuous: 10 - 500 / 8 step mm/min rapid traverse: 1,4 m/min Total power requirement: 6,5 kW weight of the machine ca.: 3,0 t dimension machine xH: 2,3 x 2,0 x 1,85 m Further features: Headstock projection min./max.: 2094 / 2544 mm Equipment: -cooling water pump with feed -Linear path measuring system - Heidenhain ND750 Accessories: -Machine vice Ksdpfx Apjvc Avhjdsdl *

Condition: like new (used), functionality: fully functional, Weiler center lathe Model Condor 81 guidance and feed spindle lathe with 3-axis digital display from K&C, NEW Geometrically overhauled with inspection protocol for new machine tolerances Technical data: >> Machine No. 84-121 >> Center height 165 mm >> Center distance 750 mm >> Spindle speeds: from 22 to 2800 rpm >> Spindle bore 40 mm >> Short taper spindle head DIN 55027 size 5 with bayonet lock >> Tailstock MK 3 >> Feeds from 0.015 to 0.46 mm/rev >> Possible threads: metric, imperial, module, and diametral pitch Kjdpjwrm Dtefx Apdodl >> Metric thread pitches from 0.18 to 28 mm >> Weight approx. 1100 kg >> Spindle brake switchable >> Length 1.83 m, Height 1.29 m, Depth 0.88 m Equipment and accessories: >> 3-axis digital display from K&C, new, 12 months manufacturer warranty with operating instructions Functions: switching mm/inch, coordinate selection ABS/INC, value halving, reference mark, tool programming for 200 pcs., taper calculation, radius/diameter, quick zeroing, count direction switching >> Collet chuck NEW, collets NEW from 3 to 26mm, increments of 1mm >> 160 mm three-jaw chuck with 2 sets of jaws NEW >> Multifix size B NEW with 3 piece steel holders >> Bed stop >> Electric chuck guard NEW >> Rear wall >> Operating manual >> Coolant device >> Machine feet About the machine: A Weiler Condor 81 guide and feed spindle lathe in a very good, geometrically overhauled condition is being offered. The guides are newly ground or newly scraped. Inspected according to test protocol. The accessories collets and chuck are new. For safety: The machine has a brake motor, electronic spindle guard and two emergency stops, making it an absolutely as-new lathe. Even at high speeds, the Weiler runs very smoothly. This newer generation of Weiler lathes is very user-friendly and allows surfaces as if ground to be produced. Take the opportunity to view this machine on site under power and convince yourself of its condition.

Condition: excellent (used), Year of construction: 1987, functionality: fully functional, Weiler Precision Lathe Model Condor 81 Lead and Feed Spindle Lathe with 3-Axis Digital Display from K&C NEW Technical Data: >> Year of manufacture 1987 Machine No. 87 835 >> Center height 165 mm >> Center distance 750 mm >> Spindle speeds: from 22 to 2800 rpm >> Spindle bore 40 mm >> Short taper spindle nose DIN 55027 size 5 with bayonet lock >> Tailstock MK 3 >> Feeds from 0.015 to 0.46 mm/rev >> Possible threads: Metric, Inch, Module, and Diametral-Pitch >> Metric thread pitches from 0.18 to 28 mm >> Weight approx. 1100 kg >> Spindle brake switchable >> Length 1.83 m, Height 1.29 m, Depth 0.88 m Accessories and Equipment: >> 3-axis digital display from K&C new, 12 months manufacturer's warranty with operating manual Functions: Switch mm/inch, coordinate selection ABS/INC, halving of display value, reference mark, tool programming 200 pcs, taper calculation, radius/diameter, quick zeroing, reversing of count direction Kdsdpjwrmuxsfx Apdol >> 1 piece 3-jaw chuck 160 mm NEW, 2 sets of jaws >> 1 piece 4-jaw chuck 160 mm, 1 set of jaws >> Collet equipment and new collets from 3 to 26 mm in 1 mm increments >> Multifix size B with 2 tool holders >> Bed stop >> Electronic spindle guard >> Rear panel >> Coolant system >> Machine feet About the Machine: A used Weiler Condor 81 in very good condition is offered. The machine is, of course, fully functional and has been completely disassembled and repainted. A very robust and powerful machine. The new 3-axis digital display from K&C makes working even easier and more precise. The machine has been electrically and mechanically tested by us. A complete oil change was carried out. This newer generation of Weiler lathes is very user-friendly. Take the opportunity to view and test this machine on site under power.

Condition: excellent (used), Year of construction: 2006, FAMUP MCP 45 CNC machining center TECHNICAL DATA axes Number of axes: 3 X-axis: 450 mm Y-axis: 300 mm Z-axis: 400 mm Feed rate Work feed X,Y,Z: 10`000 mm/min Rapid feed X,Y,Z: 30`000 mm/min Working pressure force X,Y: 2000 N Working pressure force Z: 3300 N Pallet Dimensions: 400 x 300 mm Number of grooves: 2 Groove width: 14 mm Groove spacing: 80 mm Max. Table load: 100 kg Changeover time: 9 sec. Spindle Ksdpfxsq U Rm Hs Apdjdl Spindle motor power: 5 kW Speed: 10`000 rpm Tool changer Magazine slots: 16 Max. Tool diameter: 63 mm Max. Tool length: 150 mm Max. Tool weight: 4 kg Tool change time: 1.7 sec Weight: Approx. 3000 kg No responsibility is taken for the correctness, completeness and up-to-dateness of the information.

Condition: excellent (used), functionality: fully functional, Weiler Centre Lathe Model Condor 81 Lead and Feed Screw Lathe with 3-Axis Heidenhain Digital Readout Technical Data: >> Year of manufacture: 1988 Machine No. 88-955 >> Centre height: 165 mm >> Centre distance: 750 mm >> Spindle speeds: from 22 to 2800 rpm >> Spindle bore: 40 mm >> Short taper spindle nose DIN 55027 Size 5 with bayonet lock >> Tailstock: MT 3 >> Feeds: from 0.015 to 0.46 mm/rev >> Thread cutting capability: metric, imperial, module, and diametral pitch >> Metric thread pitches: from 0.18 to 28 mm >> Weight: approx. 1100 kg >> Spindle brake can be engaged >> Dimensions: Length 1.83 m, Height 1.29 m, Depth 0.88 m Accessories and Equipment: >> 3-axis Heidenhain digital readout >> 1 pc. new 3-jaw chuck with 2 sets of jaws >> Collet chuck set, collets from 3 to 30 mm, 40 collets, some duplicate sizes >> Multifix size B with 3 tool holders >> Bed stop >> Machine feet >> Drill chuck >> Live centre For Safety: >> Cover for lead and feed screw >> 2 emergency stop buttons >> Spindle brake Kdjdpfx Aoxu Hlaopdsl About the machine: A used Weiler Condor 81 lathe from 1988 is being offered in very good condition. The machine is of course fully functional. The lead and feed screws are covered for safety. A very robust and powerful machine. The 3-axis Heidenhain digital readout makes working even easier and more precise. The machine has been electrically and mechanically tested by us. A full oil change has been carried out. This newer generation of Weiler lathes is very user-friendly. Take advantage of the opportunity to inspect and test this machine under power at our facility.

Condition: used, Year of construction: 1996, Technical details: grinding diameter: 1,5 - 75 mm grinding wheel diameter: 400 mm grinding wheel width: 160 mm work stroke: 0 - 1 mm working feed: stufenlos/ continous mm/min grinding wheel speeds: 1300 U/min control for program: Num 1020 GC total power requirement: 14 kW weight of the machine ca.: 3,8 t dimensions of machine: 3,0x2,2x2,2 m dimensions electric cabinet LxWxH: 1,5x0,4x2,0 m CIRCULAR GRINDING MACHINE - alloyed round steels as well as (grooving process) throughfeed process. - In the plunge process, the plunge-cut length is max. 160mm. - Workpiece removal automatically via rail (its function or operation is not known to WMW AG) - grinding wheel with reshaping device, speed = 1300 rpm. - regulating grinding wheel with reshaping device, infeed angle right 0-6° and left 0-2°; wheel size 280x160mm - automatic grinding wheel balancing system accessories: various grinding and regulating wheels on request The machine is operating in manual mode! The control is in the Catalan language and none of our employees can control the machine or understand the language. Kjdpfx Aju Ngyzopdjdl *