Eccentric Press - Single Column

WEINGARTEN ARP100

Condition: used, Single-column eccentric press WEINGARTEN type ARP 100 Machine no. No. 122481 Year of construction 1984 Pressure capacity 100 ton. throat 400 mm Table size 920 x 660 mm ram surface 700 x 450 mm Rear upright width 735 mm Stroke adjustment 20 - 160 mm Plunger adjustment 80 mm Installation height with 160 mm stroke max. 355 mm (without intermediate table top) Installation height with 20 mm stroke max. 425 mm (without intermediate table plate) Stroke rate 60 strokes/min. Bdjdsu Rwa Iepfx Aczek Table surface intermediate table top 920 x 610 mm Thickness of intermediate table top 90 mm Hole in intermediate table top Ø 210 / 180 mm Through-hole in machine table Ø 210 / 180 mm Table height above floor 800 mm (without intermediate table top) T-slot width in table and ram 22 mm Clamping pin bore 50 mm Motor power 11 kW Mains connection 400 Volt, 50 Hz - Hydraulic overload protection in ram - ORTLINGHAUS pneumatic clutch/brake combination - Electromotive ram adjustment with counter - Clamping pin bore with clamping piece - Front crankshaft support bearing - Gear reduction gears in closed oil bath gearbox - Two pneumatic tappet compensation cylinders - WOERNER automatic central grease lubrication - Lift release via electric foot switch or two-hand control panel - Electrical control cabinet permanently attached to the machine - Operating instructions and circuit diagram - UVV for manual insertion work Space requirement L x W x H 2200 x 1600 x 3250 mm Weight 8.3 tons Good condition

Year of construction: 1990, condition: used, pressure 75 t throat 300 mm stroke 8 - 110 mm table surface area 750 x 600 mm ram adjustment 75 mm ram surface 430 x 230 mm hole in the table 250 x 150 mm tool hole in ram 40 mm no. of strokes 60 + 90 Hub/min weight of the machine ca. 4,4 t total power requirement 4,5 - 6,8 kW dimensions of the machine ca. 1,95 x 1,1 x 2,35 m distance table/ram Hub unten, Stöß. unten 19 mm distance table/ram Hub oben, Stöß. oben 380 mm Furnishing: - with hydraulic clutch-brake combination, with new hydraulics and oil cooler - with gear transmission in oil bath - fixed table prepared for the attachment of tool changing consoles - 2 roller bars in the table - mechanical overload in the ram The following work is carried out on the machine / partial overhaul: - Machine is completely disassembled, checked, seals changed, defective parts exchanged etc - Machine is repainted - new Balluff cam control - new hydraulic unit with oil cooler for the clutch - new Vogel central lubrication - new control cabinet with touch panel and ABB safety control Bdsdpfx Aod Nl E Uoczok - Current UVV test with braking time measurement

Year of construction: 1981, condition: ready for operation (used), There are two identical eccentric presses available, nominal force: 1000kN, stroke speed: 30-85/min, stroke adjustment: 20-125mm, weight: 8t, year of construction machine 1/ 2: 1978/ 1981, with documentation. Bedpfx Acolc N Rvezjdk

Year of construction: 1965, condition: used, pressure 150 t throat 550 mm stroke 10 - 140 mm table surface area 1180 x 980 mm no. of strokes 40 Hub/min dayligth 500 mm Bdjdpscubatsfx Aczok ram surface 1040 x 800 mm ram adjustment 70 - 150 mm tool shank hole (depth x diameter) 435 x 55 mm required power 15 kW weight of the machine ca. 12 t dimensions of the machine ca. 3 x 1,7 x 3 m - with additional brake - slide weight compensation - motorized slide adjustment - central grease lubrication (manual) - table mounting plate - safe for manual inlay work

Condition: used, Year of construction: 1970, machine/vehicle number: 120895, pressure:63 t throat:250 mm stroke:8 - 100 mm no. of strokes:120 Hub/min Bdsdpfxjfx Hv Hs Aczjk table::715 x 500 mm dayligth:330 mm ram adjustment:63 mm clamping plate:700 x 480 mm hole in the table:240 mm Hole in clamping plate:110 mm dimension of ram:450 x 280 mm weight of the machine ca.:5,5 t dimensions of the machine ca.:1,2 x 1,7 x 2,7 m hydraulic tilting single column eccentric press, tilting in 4 steps, opening to rear (325 x 500mm) and below (360x160mm) with central lubrication via hand pump, additional clamping plate 700 x 480 x 850 mm, two-hand operation, foot-trip operation possible, operating-mode selector for adjustment of continuous or single stroke, emergency cut-off, piece counter, various accessories

Condition: ready for operation (used), Year of construction: 1980, Power: 300 to Size of bolster: 1.200 x 850 mm Overhang: 400 mm Width of ram: 1.100 mm Opening in bolster: 400 x 250 mm Daylight: 500 mm Frequency: 32 1/min Stroke: 30 - 140 mm Ram adjustment: 105 mm Weight: app. 19.500kg Other - allowed for 2-Hand safe working - euqipped by safety valve Herion Xsz 20 - Motorized grease lubrication - Pneumatic ram balancing cylinders - Motorized ram adjustment - T-slots in ram - Stand alone control panel - bearing of con rod overhault Bedpjd A Hbcsfx Aczedk

Condition: used, Year of construction: 1977, pressure 250 t Bdedovuuaiepfx Aczsk stroke 40 - 190 mm no. of strokes 40 /min throat 500 mm passage to the back 1050 mm dayligth 615 mm table surface area 1380 x 880 mm hole in the table 450 mm table height over floor 800 mm ram surface 1200 x 800 mm ram adjustment 125 mm power requirement 22,0 kW Weight 24,0 t dimensions of the machine ca. 2,0 x 2,5 x 3,95 m x m x m permitted for manual loading according to the German Safety Regulations (UVV) with motor, pneumatic clutch/brake combination, hydraulic overload protection in ram, pneumatic counterbalance in ram, motoric ram adjustment, manual stroke adjustment, motoric centralized lubrication, bolster plate, two-hand operation

Condition: used, Year of construction: 1989, pressure 250 t stroke 20 - 190 mm no. of strokes 24 / 48 /min throat 500 mm Bdsdpjvut Ncofx Aczek passage to the back 1000 mm dayligth 615 mm table surface area 1400 x 880 mm hole in the table 450/500 mm table height over floor 800 mm ram surface 1380 x 620 mm ram adjustment 125 mm power requirement 29,0 kW Weight 27,0 t dimensions of the machine ca. 2,0 x 2,6 x 4,1 m x m x m permitted for manual loading according to the German Safety Regulations (UVV) with motor with 2 speeds, pneumatic clutch/brake combination, hydraulic overload protection in ram, pneumatic counterbalance in ram, motoric ram adjustment, semi-automatic stroke adjustment, motoric centralized lubrication, two-hand operation can be inspected in running function in our warehouse

Condition: used, Year of construction: 1959, pressure 063 t Bjdpfx Acovuk Rwszodk throat 280 mm stroke 8 - 100 mm no. of strokes 65 /min distance table/ram, max. stroke up, adjustment up 550 mm table surface area 630 x 500 mm hole in the table 230 mm table height over floor 740 mm table adjustable 200 mm ram surface 320 x 260 mm ram adjustment 63 mm power capacity 5,5 kW weight 4,6 t Dimensions (WxDxH) 1,4 x 1,8 x 2,4 m permitted for manual loading according to the German Safety Regulations (UVV) with motor, friction clutch, mechanical overload protection in ram, manual stroke adjustment, manual ram adjustment, adjustable table, manual centralized lubrication, two-hand operation Press is currently under revision

Condition: used, Year of construction: 1991, Pressure capacity 1,500 kN Adjustable stroke 20 - 132 mm ram adjustment max. 90 mm Stroke rate 50 / 75 1/min. Bsdpfsrm Nqmjx Aczsdk Further data and pictures on request used, the press is currently completely disassembled not functional and must be mechanically and electrically overhauled