Lead/traction spindle lathe

WEIPERT

Condition: good (used), Year of construction: 1967, LZ-Lathe Fabr.WEIPERT TYPE:UD 500 e year 1967 Gsdpfxeu Rd H Io Anloiu with digital readout ,top support feed tool holder MULTIFIX size C ,Forkardt chuck 315 mm. Center height : 250 mm Center width : 1500 mm spindle bore : 65 mm Spindle speed : 14 -1400 rpm Machine is in good condition .

Condition: new, Year of construction: 2024, machine/vehicle number: 302340, Profile Bending machine KB Türkei model MB 30 bottom shaft 30 mm top shaft 35 mm two rollers driven with basement capacity: up to round tube 48 x 3,0 mm Gsdpfx Aod S Uf Ssnlsiu flat material 50x10 mm square tube 40x40x3,0 mm weight 170 kg motor 0,75 kw 400 Volt 50 Hz 3 ph.

Condition: used, Year of construction: 1960, turning diameter over bed 480 mm turning diameter over slide rest 260 mm turning length 1500 mm turning speeds 90 - 1120 U/min centre height 240 mm spindle bore 52 mm total power requirement 7,5 KW weight of the machine ca. 2,3 t dimensions of the machine ca. 3,0 x 1,3 x 1,5 m Engine Lathe Gijdpfoy Umb Dex Anleu - 3-jaw chuck (200 mm) - Quick-change tool post - Steady rest - Machine lamp - Chip tray - Center point

Condition: excellent (used), turning length: 5,500 mm, total height: 2,900 mm, total length: 9,000 mm, total width: 2,900 mm, overall weight: 32,000 kg, Make: WEIPERT Type: W1400 Gjdpfxswzhzle Anloiu Control: R&D MTC3 DBC Turning Length: 5500mm Swing over bed Ø: 1400mm Swing over cross slide Ø:960mm Length: 9000mm Width: 2900mm Height: 2900mm Weight: 32000kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Year of construction: 1965, condition: used, pressure 150 t throat 550 mm stroke 10 - 140 mm table surface area 1180 x 980 mm no. of strokes 40 Hub/min dayligth 500 mm ram surface 1040 x 800 mm ram adjustment 70 - 150 mm tool shank hole (depth x diameter) 435 x 55 mm required power 15 kW weight of the machine ca. 12 t dimensions of the machine ca. 3 x 1,7 x 3 m Gisdpfxscubats Anlsu - with additional brake - slide weight compensation - motorized slide adjustment - central grease lubrication (manual) - table mounting plate - safe for manual inlay work

Condition: used, greates pass round over bed 480 mm swing diameter over bed slide 300 mm turning length 1500 mm centre height 240 mm centre distance 1500 mm spindle bore 42 mm spindle turning speed range 14 - 1400 U/min Gisdpjtqqx Aofx Anlju total power requirement kW weight of the machine ca. 2,4 t dimensions of machine L x W x H 3,00 x 1,05 x 1,40 m Accessories: 3-jaw chuck 250 mmø, MULTIFIX-head, running center

Condition: good (used), Technical parameters Maximum cutting capacity Round 650mm Square 650×800mm Saw blade Saw blade speed 20~80 m/min Saw size 54X1.6 Giedpfx Asullzhjnlsu Guides Carbide and bearing blade guides Cleaning Wire brush & flood coolant Tension Hydraulic Motor power 7.5 kW Hydraulic 2.2 kW Coolant 0.12 kW

Condition: good (used), Studer S30-12 cylindrical grinding machine TECHNICAL DATA Main dimensions Center height: 125 mm Center width: 400 / 700 / 1025 mm Largest longitudinal slide path: 400 / 700 / 1000 mm Longitudinal slide Gjdpfxovca Ize Anlsiu Table speed: 50 - 5000 mm/min Reversing delay: 0-6 s Smallest automatic travel: 1.5 mm Max. stroke: 400 / 700 / 1020 mm Max. Table inclination: 12 / 30 / 78° Cross slide Swivel range: +- 45° Quick adjustment: 40 mm Feed path with handwheel: 20 mm Largest plunge depth: 1.7 mm Sanding headstock Grinding wheel diameter x width x bore: 450 x 80 x 203 mm Speed: 1340 / 1500 1625 / 1800 / 2000 / 2200 rpm Coarse adjustment: 210 mm Workpiece headstock Swivel range: 0 - 90 Speed range: 30 - 675 rpm Mounting cone: Morse 5 Collets: W25 Tailstock Mounting cone: Morse 3 Adjustment travel of the center: 30 mm Total power requirement: 5 / 8.25 kW No liability is assumed for the correctness, completeness and up-to-dateness of the information.

Condition: new, Year of construction: 2024, Working range Center distance 1000 mm Turning diameter over bed 356 mm Rotation Ø over support 220 mm Bed width 206 mm Travel paths X-axis travel 178 mm Z1-axis travel 92 mm Swivel range top slide ± 50° Main spindle Speed range, high 550 1/min - 3000 1/min Speed range, low 30 1/min - 550 1/min Spindle holder Camlock D1-4 Spindle bore 38 mm Spindle cone 5 MK Feed rate Feed X-axis 0.014 mm/rev - 0.206 mm/rev Feed Z-axis 0.043 mm/rev - 0.653 mm/rev Thread cutting Thread cutting, metric (37) 0.4-7 mm Thread cutting Whitworth (28) 4-56 TPI Tailstock Tailstock pinol diameter 45 mm Tailstock taper 3 MK Tailstock quill stroke 120 mm Tailstock cross adjustment ± 10 mm Drive power Giodpfxou Sklyj Anlsu Motor power main drive 4 kW Dimensions and weights Dimensions (length x width x height) 1.95 m x 0.75 m x 1.55 m Weight 880 kg

Condition: used, Year of construction: 1953, You can find additional images, data, and detailed information in the PDF notes. Should you have any further questions or require more information, please do not hesitate to contact us at any time. We are at your disposal. Gjdpfxex R Tnvo Anlsiu

Condition: ready for operation (used), Year of construction: 2019, operating hours: 14,530 h, Control Unit Brand FANUC Model 31i-Model B Gisdpfx Ansx D I Axolju Main Drive Number of axis 3 This 3-axis Star SR-20J N was manufactured in 2019. It's a Swiss type turning machine designed for precision and efficiency. Ideal for intricate machining tasks, this model offers robust performance in a compact footprint. If you are looking to get high-quality turning capabilities, consider the Star SR-20J N machine we have for sale. Contact us for more information. Application Types Turning

Year of construction: 1967, condition: used, LatheFabr. Weipert Type W500 Gjdpfxoh Rwkle Anloiu turning diameter 500 mm Turning length 1000

Condition: used, functionality: fully functional, spindle bore: 102 mm, center height: 400 mm, turning length: 2,000 mm, 26 spindle speeds from 4.5 to 1400 rpm - powered top slide - rapid traverse - 400 mm Forkardt chuck Gedpfx Aoy D H Rwsnloiu

Condition: new, functionality: fully functional, turning diameter over cross slide: 280 mm, spindle bore: 58 mm, turning diameter over bed slide: 470 mm, center height: 235 mm, turning length: 1,000 mm, quill stroke: 127 mm, quill diameter: 68 mm, total length: 2,150 mm, total width: 810 mm, spindle speed (max.): 2,000 rpm, spindle speed (min.): 20 rpm, bed width: 300 mm, overall weight: 1,800 kg, quill mount: MK 4, Tip height: 235 mm Giodpfxjcirnis Anlju Center distance: 1000 mm Spindle bore: 58 mm Spindle nose according to DIN 55029: Camlock D6 Motor power: 5.5 kW Spindle speed range: 20-2000 mm Features include Hardened and precision-ground Z-axis guideways Turcite coatings (on mating surface) of the tool and face slides Manual central lubrication with one pump for longitudinal and cross slides Complete coolant system with rear splash guard and splash guard on the slide Chuck guard Switch rod with 3 adjustable cams Machine light Fixed center point Set of machine mounting plates

Condition: like new (used), Year of construction: 2008, SPECIFICATION KB-45 Cutting capacity 455mm Maximum working height 255mm Table 600 x 500 mm Tilt 4 ways up to 15° Saw blade length 3490mm Saw blade width 3-16mm Saw blade speed 25-115m/min Butt welder capacity 3-16mm Motor size 1HP Weight 285 Kgs Height 2020mm Width 1100mm Depth 660mm STANDARD FEATURES Overload switch Single-phase / 3-phase supply Built-in saw blade and tire cleaning brush Saw blade welder, blade shear and grinder Godpfx Aneu Rdr Rjlsiu Slotting table Low-voltage halogen lamp Mitre guard for angled cuts Quick rip fence for straight cuts