Condition: ready for operation (used), Spare parts package for Kiefel KMD 85 consists of electronics, gears and motors see photos. Folqoq Evmcj Ep A Isgb Chain transport is not included in the pictures.

Condition: used, Twin screw extruder Fgelev U Nnusq Ep A Isb 34mm diameter 400 volts, 128 amps 2 pairs of spare screws Used for powder coatings Hourly output 250-400 kg depending on the product

Condition: excellent (used), Year of construction: 2005, KM 500/2700C2 Technical Specifications Clamping Side: Clamping Force: 5000 kN Tie Bar Dimensions (H x V): 900 x 800 mm Minimum Installation Height: 480 mm Maximum Platen Distance: 1650 mm Centering: 200 mm Mold Weight: 7900 kg Injection Side: Fgjlev Uzq Ujq Ep A Iob Screw Diameter: 80 mm Displacement: 1433 cc Injection Pressure: 1829 bar Equipment: MC 4 Control System Core Pulls: 2+2 Machine is sold without robots and peripherals!

Year of construction: 1990, Condition: good (used), This haul-off machine, manufactured by Battenfeld Extrusionstechnik GmbH, is in the machine storage of Plastima Used Machinery. The machine, a model Haul-Off R630/6V, dates from the year 1990. Brand: Battenfeld Extrusionstechnik GmbH Model: Haul-Off R630/6V Year of manufacture: 1990 Voltage: 380 V Power: 4,5 kW Pipe diameter max: 110 mm to 630 mm Fjlqerrv Uwe Ep A Isgb

Year of construction: 2008, Condition: refurbished (used), Functionality: fully functional, Twin parallel screw extruder - Manufacturer: WEBER - Type: DS 8.22 - Year: 2008 - Double parallel screws ø87mm 22D - 5 heating zones on the cylinder + 2 cooling zones - 5 tool heating zones - Engine power: 56kW - Up to 200kg/h profile - 300kg/h tubes Very good condition Folswc Dhdjq Ep A Iegb

Condition: like new (used), Year of construction: 2009, operating hours: 49,500 h, Functionality: fully functional, machine/vehicle number: 172007, clamping force: 100 kN, screw diameter: 35 mm, Machine from clean room production. Fgelqewcki Ie Ep A Ieb

Condition: good (used), Year of construction: 2015, Technical Datasheet – ENGEL DUO 7050/1500 WP 🔩 Clamping Unit: 1. Clamping force: 15,000 kN 2. Opening force (with pressure cushion): 1,000 kN 3. Opening force (without cushion): 476 kN 4. Opening stroke: 2,550 mm 5. Mold height (min – max): 700 – 1,360 mm 6. Max. daylight (platens open): 3,250 mm 7. Platen dimensions (H × V): 2,420 × 2,170 mm 8. Tie bar spacing (H × V): 1,865 × 1,430 mm 9. Tie bar diameter: 250 mm 10. Max. mold weight: 45,000 kg (2/3 on moving platen) 11. Ejector stroke: 300 mm 12. Ejector force: 230 kN 13. Dry cycle time (Euromap 6): 4.8 s 14. Dry cycle stroke: 1,300 mm 🧩 Injection Unit: 1. Screw diameter: 105 mm 2. Screw stroke: 480 mm 3. Injection volume: 4,160 cm³ 4. Screw speed (max): 130 rpm (up to 150 rpm with performance adjustment) 5. L/D ratio (3-zone screw): 22 6. Plasticizing rate (3-zone screw): 113 g/s (max. 130 g/s) 7. Plasticizing rate (barrier screw): 148 g/s (max. 171 g/s) 8. Injection speed: 800 cm³/s (630 cm³/s at higher pressure) 9. Injection pressure (standard/boost): 1,650 / 2,090 bar 10. Nozzle stroke: 950 mm 11. Nozzle contact force: 150 kN ⚙️ Drive & Energy: 1. Installed power (injection unit): 74 kW 2. Heating zones (incl. nozzle): 7 3. Pump drive power: 161 kW 4. Oil tank volume: 1,800 liters Felewfgi Aoq Ep A Iegb ⚖️ Machine Weight: 1. Clamping + Injection Unit: 66 tons 2. Approx. additional components: 17 tons

Condition: ready for operation (used), Year of construction: 2000, operating hours: 3,688 h, General Data Measurements width 1160 mm Measurements depth 5146 mm Measurements height 2365 mm Machine weight 9800 kg Injection Unit Screw diameter 60 mm Shot weight 644 g Stroke volume 678 cm³ Fgeljwg H Uzsq Ep A Ieb Clamping Unit Clamping force 250 T Opening stroke 580 mm Max open daylight 1130 mm Mould height min 250 mm Mould height max 550 mm Additional Equipment Core Pull: 2 Air Circuit: 1 This Victor VS-250 hydraulic injection moulding machine was manufactured in 2000. It is ideal for precision plastic processing tasks. Contact us for more information about this machine. Application Types Injection Moulding

Condition: good (used), I will sell an aggregate/injection molding machine for the production of polystyrene boxes such as fishbox, thermobox (3 sizes of boxes - adjustable mold). The price includes a set, i.e.: Fgelq Ep Asua Dqis Isb - injection molding machine, aggregate, automatic machine for the production of polystyrene EPS shapes - very good condition, year of manufacture 2023. - configurable mold for the production of thermoboxes - 3 sizes of boxes. With appropriate equipment, it is possible to produce high-density blocks and shapes (70-90 kg / m3) on the above set used for cutting shapes for warm assembly under windows, doors, HS Along with the line, the transfer of copyright to the box designs. We also have other elements/devices for sale, such as: - injection molding machine, aggregate, machine for the production of EPS polystyrene foundation plates + plate mold - Certus container steam boiler room (oil steam generator) - EPS foamer - steam installation: boiler room - machines - 3m3 steam tank - installation for transporting foamed EPS - EPS silos - polystyrene crusher - many spare parts Possibility to send more photos and information by email. Possibility to sell individual components of the set separately.

Year of construction: 2002, Condition: used, Working widths 1800 mm roll surface width 2000 mm Number of rollers 2 St./ea Upper roll Gravur oder Stahl dia diameter of upper rolls 210 mm Heating - upper roll Elektro Lower roll Gummiert dia diameter of lower rolls 300 mm Roller covering - soft rubber 95 °Sh weight 2 t dimensions of the machine ca. 3,0 x 1,5 x 1,8 m Embossing Calender with exchangeable top roll, The following spare rollers are included with the machine: • 1 x steel roll, chrome plated Fgeljt An E Req Ep A Ijb • 3 x engraving rolls, various designs • 1 x spare bottom roll - rubber coated On the outlet side there is a small batch - rising batch winder ATTENION: the electrical control unit is defective, still needs to be replaced, therefore SPECIAL PRICE for self-repair

Year of construction: 2003, Condition: good (used), For sale we have an injection molding machine of the company Arburg and the type 420 C 1000 150/60 Fgslqoi E Ttqe Ep A Ijb The machine has been serviced regularly and on time Designation: 420 C 1000- 150/60 Machine number: 191198 Year of manufacture: 2003 Machine number: 110846 Operating hours: 51629 pump hours Spraying cylinder Ø 25 mm Horizontal Ø 15mm Vertical Weight: 2550 kg Length: 4,5m Equipment: 2 core pulls , cavity pressure ,accumulator ,Q-switch ,hot runner controller internal , conveyor belt, rotary plate Not in the offer are granulate conveying systems, temperature control units or external hot runner controllers Prices plus value added tax Visits are possible by appointment. Please contact us, our team will be pleased to help you. Trade-in or exchange possible! Machines purchase / sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES ETC. Do you need a high-quality but inexpensive metalworking machine for your production? Or do you want to sell yours? For more information or to contact us, please visit our website

Condition: like new (used), Functionality: fully functional, machine/vehicle number: SBO 6/10, Sidel Stretch Blow Moulding Machine Max. output: 6.000 bottles/hour. Max. bottle size: 3.000 cc. Blow stations: 6. Machine is in very good conditioning and well maintained. Fslq Epjg Ailcj A Iogb GENERAL INFORMATION The SBO 6/10 has 6 molds and 10 heating modules. Will work with a wide range of bottle sizes and styles from 0.25 to 3 liters. Sidel 2-step ^PET stretch-blow molders require previously manufactured preforms be supplied to the machine. Separating the bottle manufacturing and preform manufacturing processes allow production to be optimized, provide greater flexibility of operation and use, and provide higher production output rates and yield. MAXIMUM PREFORM DIMENSIONS Neck height 9 – 41 mm (measured from bottom of support ring) Minimum inside diameter of neck 19 mm Maximum outside diameter of neck 34 mm Preform support ring diameter 29 – 51 mm Maximum preform length 210 mm MAXIMUM BOTTLE DIMENSIONS Maximum bottle diameter 130 mm Maximum bottle height 380 mm Bottle capacity 0.25 – 3 liters AVERAGE PREFORM WEIGHTS (non carbonated and carbonated liquids) 0.25 liter bottle 14-20 grams 0.50 liter bottle 20-33 grams 1.00 liter bottle 26-40 grams 1.50 liter bottle 35-51 grams 2.00 liter bottle 44-58 grams 3.00 liter bottle 68-84 grams BLOW WHEEL Height 3.5 meters Number of molds 6 Closing force 10 tons Item height (under neck) at outfeed 1.4 meters approximately Machine DC drive motor power 4 KW HEAT CONDITIONING Height 2 meters Number of oven heating units 10 Number of heating zones per unit 8 Maximum power 170 KW ELECTRICAL USAGE Maximum supplied power 200 KW Average consumption 100-150 KW/hr (varies per bottle being produced) COMPRESSED AIR Supplied power from 7-35 bar Pressure 7 bar Flow rate 50-100 Nm3/hr (varies per bottle being produced) Blow pressure – champagne base up to 25 bar Blow flow rate – champagne base 110-550 Nm3/hr Blow pressure – petaloid base up to 35 bar Blow flow rate – petaloid base 155-770 Nm3/hr CHILLED WATER Temperature 10-12 degrees Centigrade Pressure 5-6 bar Flow rate up to 6 cubic meters/hour Kcal to be removed up to 16,000 Kcal/hour WEIGHT Blow wheel with molds 8 tons Heat conditioning unit 2.2 tons Preform feeder 0.65 tons Electrical cabinet 0.85 tons PREFORM HEAT CONDITONING The preforms are transferred neck up to the heat conditioning device. This unit continuously insures the preforms are inverted before passing, neck down, in front of the heating units and then inverts them again. During the heating phase, the preforms are rotated and their necks protected from the heat in order to optimize the distribution of heat without deforming the neck. Heating is insured by 10 heat modules. Each unit can accommodate up to 8 infrared lamps stacked horizontally whose ends are air cooled. The heating power of 8 zones, corresponding to the 8 rows of lamps, can be controlled in order to optimize the heat profile. These zones are regulated on all SBO Models. After heating, a control by infra-red camera of preform temperature enables regulation of the zones under control, thus insuring maintenance of the required temperature.

Condition: excellent (used), Year of construction: 2008, Functionality: fully functional, Vacuum Forming Machine with: Bush vacuum pump Typ: RA 0255 D 561 CUXX Servo Plug Assist Clamping frame lifted parallel Servo Form table Siemens S7 control 8 Cooling fans Technical specifications Max. Plate size: 2250x1250 mm Max. Forming area: 2200x1200 mm Max. Thickness of the panel: 10 mm Max. Drawing height: 700 mm Max. Tool height: 860 mm Only 2.640 Working hours The machine has an automatic changeover function, upper punch with pneumatic drive, mould table with pneumatic drive and position storage. Electric heating, individual heating pattern is stored, energy-saving mode during work breaks by switching off the vacuum pump and lowering the set temperature of the radiant heaters. Temperature control connection for top and bottom Under-tension frame (max. 140 °C); Heating molding machine variants:- 8-position switch Forming table with pneumatic drive, Forming table speed digital adjustable (7 levels); Top table - with pneumatic drive; - Synchronization device for asymmetrical Burden; - automatic top table tool clamping - automatic conversion Fgelov Uzflsq Ep A Ieb - Speed digitally adjustable (7-stage via valve cascade); - Top table can be used as a demoulding aid 8-way cooling fan Additional double fan in the front center (1 motor with fan mounted on both sides without nozzle), Air shower cooling - connection for upper clamping frame; Include this complete set of Frames. All frames with substructure and base plate. Some with cooling possible valued in approx 40.000 euros 1740 x 700 1960 x 1060 2040 x 735 1270 x 960 860 x 860 2260 x 1070 1720 x 350

Condition: ready for operation (used), Year of construction: 2003, operating hours: 8,666 h, General Data Measurements width 1180 Measurements depth 4343 Measurements height 2190 Machine weight 6400 Injection Unit Screw diameter 55 mmm Shot weight 451 g Stroke volume 475 cm³ Clamping Unit Clamping force 180 T This Victor VS180 was manufactured in 2003. It is a hydraulic injection moulding machine, ideal for precision plastic processing. Contact us for more information about this machine. Application Types Felqowg Iaro Ep A Iogb Injection Moulding

Condition: excellent (used), For sale, Form thermostat - Tool Temp TT-188 Max. heating temperature - 90°C Fgelevzb Nqsq Ep A Ijb Medium - water Power: 9850 Watts The device has: - vacuum pump vaccum - vacuum tank - function of sucking the medium out of the mold - the device can be integrated with the machine, maintenance-free

Condition: excellent (used), Year of construction: 2021, ENGEL DUO 17060/2700 (2021) 🔧 Technical Specifications • Clamping force: 27,000 kN Fgjlqswd Sywj Ep A Iob • Tie bar spacing (horizontal × vertical): 2,130 × 1,750 mm • Platen size: 2,970 × 2,640 mm • Mold height (min–max): 800 – 1,900 mm • Opening stroke: 3,100 mm • Max. distance between platens: 5,090 mm • Dry cycle (Euromap 6, 6 mm stroke): 5.8 s • Max. mold weight (fixed/moving platen): 50,000 kg each 🧩 Injection & Plasticizing Unit • Screw type: S4V G18 • Screw diameter: 150 mm • Injection volume: 10,780 cm³ • Injection pressure (max): 1,620 bar • Injection speed: 87 mm/s • Plasticizing rate (barrier screw): 235 g/s • Screw speed: up to 115 rpm 🔩 Nozzle & Ejector • Nozzle stroke: 1,300 mm • Nozzle contact force: 210 kN • Ejector stroke: 400 mm • Ejector force: 385 kN ⚙️ Drive & Power • Main motors installed power: 192 kW • Reload pump motor: 16 kW • Oil reservoir capacity: 1,600 liters • Main power: 3×400V, N+PE / 50 Hz ➕ Additional Features & Configuration • T-slot platen with ejector back confirmation • Locating ring Ø 120 mm • Sprue bush “R”: 19 mm • Hydraulic corepull 2+2, air valve 1+1 • Mold heating control with 144 zones (24pin, K-type) • Valve gate interface with 36 zones (16pin DC24V) • Abrasion/corrosion-resistant screw barrel • Servo hydraulic drive • Oil maintenance system • UPS (AVR) backup unit • Robot interface EM67 • Cooling circuit: 1” inlet, 2 zones per platen (90°) • Autoclamp system for fast mold changes

Condition: good (used), Functionality: fully functional, 3 rotor blades Fgolq Epev A Ahdo A Isb 2 stator blades Blade inlet 220 x 200 mm Power 3 kW

Condition: ready for operation (used), Year of construction: 1999, operating hours: 4,937 h, General Data Measurements width 1180 Measurements depth 4343 Measurements height 2190 Machine weight 6400 Injection Unit Screw diameter 55 mm Fjlq Epjwg Ia Ee A Iegb Shot weight 451 g Stroke volume 475 cm³ Clamping Unit Clamping force 180 T Max open daylight 970 mm Distance between bars 510 x 510 mm Mould height min 200 mm Mould height max 500 mm This Victor VS180 was manufactured in 1999. A hydraulic injection moulding machine, it offers robust performance for various plastic processing applications. Consider the opportunity to buy this Victor VS180 hydraulic injection moulding machine. Contact us for more information. Application Types Injection Moulding

Condition: good (used), Year of construction: 2006, Model: HM 210/1000 S Clamping force: 210 t Distance between tie bars: 630 x 570 mm Fgslqsu Ekbho Ep A Ieb Mould height: 300 mm Daylight max. : 1050 mm Screw diameter: 50 mm Injection pressure: 2016 bar Injection volume: 491 cm3 Shot weight: 440 g Transport parameters: weight 10000 kg, L x W x H: 5000 x 1700 x 2300 mm Controll: Unilog B4 Videos on request.

Year of construction: 1995, Condition: good (used), Functionality: fully functional, Manufacturer Pallmann Type PS-G 250 x 500 Blade inlet 250 x 500 cm Folqovkw A Eo Ep A Isgb Motor power 15 kW Slow-running mill with gear - quiet and dust-free Year of manufacture 1995 Additional sieves - 4 pieces

Condition: ready for operation (used), Year of construction: 2003, operating hours: 7,507 h, General Data Measurements width 1135 Measurements depth 3354 Measurements height 2080 Machine weight 4100 Injection Unit Screw diameter 40 mm Shot weight 155 g Stroke volume 163 cm³ Clamping Unit Clamping force 80 T Max open daylight 670 mm Distance between bars 360 x 360 mm Mould height min 150 mm Mould height max 350 mm This Victor VS80 hydraulic injection moulding machine was manufactured in 2003. It is a robust and reliable choice for your production needs. Contact us for more information. Fgelqswg H U Uj Ep A Ijb Application Types Injection Moulding

Condition: good (used), Functionality: fully functional, 3 rotor blades 2 stator blades Folq Epev A Ahks A Iogb Blade inlet 220 x 200 mm Power 3 kW

Condition: ready for operation (used), Year of construction: 2018, General Data Measurements width 1200 mm Measurements depth 4100 mm Measurements height 1820 mm Machine weight 3500 kg Fgslq Epov Sfxqs A Isb Clamping Unit Clamping force 600 kN Size of mold platens 545 x 505 mm Ejector stroke 70 mm This Haitian ZHAFIR Zeres ZE600 was manufactured in 2018. It is a hydraulic injection moulding machine, ideal for precision and efficiency in plastic processing. Consider the opportunity to buy this Haitian ZHAFIR Zeres ZE600 hydraulic injection moulding machine. Contact us for more information. Application Types Injection Moulding

Condition: good (used), Functionality: fully functional, 3 rotor blades 2 stator blades Blade inlet 220 x 200 mm Fgslqev A Agys Ep A Ieb Power 3 kW

Year of construction: 2006, Condition: ready for operation (used), Additional Equipment Machine includes an SA 500 extractor built in 2006 and a 6m long cooling section. This KUHNE KS45-24D compounding extruder was manufactured in 2006. Ideal for processing a variety of materials, it offers robust construction and reliable performance. Consider the opportunity to buy this KUHNE KS45-24D compounding extruder. Contact us for more information. Application Types Fsljv Sfw Hsq Ep A Iogb Extrusion