Used roll forming lines for sale (88)

Condition: good (used), DREISTERN P3.100 Profiling Line – 16 driven stations and 2 × 18.5 kW Short title for platforms with character limits: DREISTERN P3.100 Profiling Line, 16 driven stations Platform data Chsdpfx Abjzzyd Nsred * Machine type: Profiling line / Roll forming line * Manufacturer: DREISTERN * Model: P3.100 * Year of manufacture: not known / to be added before publication * Condition: used, dismantled * Control system: not available For sale is a DREISTERN profiling line, type P3.100, with 18 stations, 16 of which are driven. The line is equipped with 16 profiling stands, 50 mm working shafts, quick-change plates, and two Bosch motors, each with 18.5 kW. The modular design with mechanical quick clamps and quick-change plates is suitable as a solid mechanical base for customer-specific roll forming applications. A constructive expansion with additional stations is possible. According to the previous operator, the line operated flawlessly until it was dismantled at the customer's site. The control system is not available and is not included in the scope of supply. Recommissioning or control system adaptation by the buyer is therefore necessary. Machine bed and drive * Production direction: from left to right * Axle distance: 330 mm * 18 stations in total * 16 stations driven, with 16 gearboxes * Quick-change plates * Mechanical quick clamps * Coolant piping * 2 × Bosch motor, each 18.5 kW Profiling stands * Number in scope of supply: 16 pieces * Tool width per stand: 275 mm * Working shaft diameter: 50 mm * Working shaft connection: 30 mm with groove * Fixed lower shaft * Axial adjustment * Adjustment range lower to upper shaft: 80–170 mm Gearboxes * Worm gear ratio: 1:7.5 * Lower/upper shaft ratio: 1:1 Scope of supply * Machine bed with gearbox support * Infeed table * Pneumatic measuring wheel unit * Special straightening device * 16 gearboxes * 16 profiling stands * 2 Bosch motors, each 18.5 kW * 32 universal joints

Condition: good (used), Profile roof tiles Entry width 1250 mm Cjdpfjxam Rajx Abrshd Material thickness 0.5 - 0.75 mm Year of manufacture 2002 Speed 8 m/sec.

Condition: used, Year of construction: 2001, functionality: fully functional, machine/vehicle number: 1895, SWAH SLV-3 – Corner Insertion Machine A specialized, highly efficient pneumatic/electric machine designed for the automatic insertion and clamping of corner pieces into rectangular duct flanges (TDC/TDF/Slide-on profiles). Manufactured by the European specialist SWAH, the SLV-3 significantly speeds up the final assembly of rectangular ductwork while ensuring rigid, airtight joints. Specifications • Manufacturer: SWAH s.r.o. (Czech Republic) • Model / Typ: SLV-3 • Year of Manufacture: 2001 • Serial No.: 1895 • Application: Fast and automated press-fitting of metal corners into rectangular ventilation ducts. • Voltage: 400 V • Current: 1.1 A • Machine Weight: 96 kg Chodpozbipvefx Abrod Key Features & Components • High-Speed Assembly: Eliminates manual hammering, allowing the operator to lock ventilation corners into the profile in seconds with consistent, high-quality results. • Heavy-Duty Pressing Mechanism: Delivers a secure, tight seal between the duct profile and the corner piece without deforming the sheet metal or damaging the zinc coating. Condition & Availability • Status: Fully operational and in good working condition. • Ready for delivery

Condition: new, Year of construction: 2026, functionality: fully functional, total width: 550 mm, total length: 2,320 mm, total height: 1,000 mm, input voltage: 220 V, working width: 300 mm, spindle motor power: 750 W, warranty duration: 12 months, power: 0.75 kW (1.02 HP), overall weight: 410 kg, Equipment: CE marking, New Misirli seamless rain gutter roll forming machine (portable) for producing seamless gutters on site or in the workshop, directly from metal coil. Supplied new by the authorised Misirli sales and service partner in Sofia, Bulgaria. The machine forms aluminium, pre-painted steel, galvanised steel and copper coil into a U-section rain gutter, cut to any length the operator needs – no joints along the run. Codpsz Dqubofx Abrehd Technical data - Coil (strip) width: 300 mm - Material thickness: 0.40 – 0.60 mm - Materials: aluminium, pre-painted steel, galvanised steel, copper - Production speed: 10 m/min - Drive motor: 1 HP (0.75 kW), 2800 rpm, chain and gear drive - Power supply: 220 V AC, 50–60 Hz (single phase) - Machine dimensions (L x W x H): 2320 x 550 x 1000 mm - Weight: 410 kg - Forming rolls: solid, CNC-machined, hard-chrome plated - Gutter profile: K-style (ogee), top width 127 mm (approx. 5"), bottom 85 mm, back height 85 mm, front height 90 mm Quality and compliance: CE marked, built according to the Machinery Directive and Low Voltage Directive, electrical equipment tested to EN 60204. All parts are manufactured in-house on CNC machines; spare parts are kept in stock. Larger versions also available: 330 mm strip (420 kg) and 370 mm strip (0.50–0.60 mm, 1.5 HP, 2860 x 730 x 1160 mm, 500 kg). Warranty: 1 year. Demonstration in Sofia possible.

Condition: used, Guard Rail Roll Forming Line: Cjdexnmmqopfx Abrehd • The production line for road safety barriers consists of: • Accessories and rollers for the production of 2- and 3-wave guard rails • Bending machine for 2- and 3-wave profiles • 19-station roll forming machine, complete with rollers and motorization • No. 3 punching stations • No. 1 cutting station • No. 7 hydraulic power units • No. 1 station with feeding rollers

Condition: ready for operation (used), Year of construction: 2002, Profile T18 Feed width 1250 mm Material thickness 0.5 – 0.63 mm Year of manufacture 2002 Control system: Siemens PLC (new) The machines can be inspected in operation at our plant in 94486 Osterhofen after prior arrangement. Chjdpfshryh Ujx Abred

Condition: ready for operation (used), Year of construction: 2018, Machining sides: 3, workpiece materials: aluminium/steel, travel X: 4000mm, feed rate: 120m/min, A-axis: +/-110°, spindle speed: 18000rpm, tool holder: SK30, tool positions: 8, max. profile dimensions X/Y/Z: 4000mm/250mm/190mm, machine dimensions X/Y/Z: approx. 5750mm/2100mm/2350mm, weight: approx. 4000kg, control: Mecal. Documentation available. On-site inspection is possible. Codpfoyh Nv Hsx Abrehd

Condition: ready for operation (used), Year of construction: 2018, functionality: fully functional, sheet thickness steel (max.): 6 mm, sheet thickness aluminum (max.): 7 mm, total width: 1,700 mm, total length: 31,000 mm, total height: 2,000 mm, input voltage: 400 V, working width: 1,250 mm, coil weight: 5,000 kg, overall weight: 8,800 kg, T20 Trapezoidal Sheet Roll Forming Line for Sale * Model: T20 Trapezoidal Sheet Roll Forming Line * Year of Manufacture: 2018 * 5-ton hydraulic decoiler included * Automatic stacker at the end of the production line The machine has seen very little use and is in excellent working condition. It has been well maintained and is fully operational. The production line is currently dismantled, making it ready for transport. Cedpfozhip Ijx Abrshd If you need any additional information, photos, or videos of the machine in operation, feel free to contact us.

Condition: like new (used), Year of construction: 2022, Infeed height 900 mm Infeed width 300 – 800 mm Non-ferrous metals: Either 0.6 – 0.8 mm or 0.8 – 1.0 mm (has to be set before ordering) Non-ferrous metals: 1.0 – 1.2 mm (only with façade profiles) Steel (320 N/mm²): 0.55 – 0.70 mm Stainless steel: Max. 0.5 mm Cjdjxwxdgepfx Abrshd 3,830 mm x 2,045 mm x 1,275 mm 1,770 kg

Condition: excellent (used), Year of construction: 2023, functionality: fully functional, Complete P20 & P30 HVAC Duct Flange Profile Roll Forming Lines with Butyl Sealant System For sale is a complete set of two professional roll forming lines for the production of P20 and P30 flange profiles, used in the manufacturing of rectangular HVAC ducts and fittings. The set includes: - P20 flange profile production line - P30 flange profile production line Both machines are equipped with an integrated butyl sealant application system. Depending on production requirements, the profiles can be manufactured with or without factory-applied butyl sealant. This provides full flexibility and allows the finished profiles to be adapted to different duct manufacturing technologies and customer requirements. The machines perform the complete production process – from coil decoiling, through multi-stage roll forming, to automatic cutting of the finished profile to the required length. Technical highlights - 18 roll forming stations - Automatic PLC-controlled cutting system - Production speed up to 9 m/min without sealant application - Production speed up to 5 m/min with butyl sealant application - Integrated butyl sealant application system - Complete production lines for P20 and P30 profiles Both machines are in very good technical condition. Since new, they have been used exclusively for the production needs of our own HVAC duct manufacturing facility. They have not been used for continuous mass production of profiles for commercial sale, therefore their overall level of utilisation is relatively low. Csdjzx Rz Hopfx Abrehd Both production lines are fully operational, properly adjusted, tested and ready for immediate production. The machines are offered as a complete P20 + P30 set, allowing the buyer to establish in-house production of the two main flange profile sizes commonly used in the manufacturing of rectangular HVAC ducts and fittings. Relocation and commissioning support We can provide technical assistance with dismantling and relocation of the machines. We can also support the buyer with installation, adjustment, testing and commissioning at the new production facility, helping to ensure that both lines are properly set up and ready for production after relocation. The machines can be inspected while in operation, and production tests can be carried out prior to purchase. The indicated price is NET and VAT will be added where applicable.

Condition: ready for operation (used), A 4-axis CNC bar machining center Elumatec is available. Version: 6,4m, travel X/Y/Z: 7720mm/845mm/620mm, max. machining length face/non-face: 7720mm/7600mm, positioning accuracy: +/-0.1mm/m, max. spindle speed: 24000rpm, tool holder: HSK-63F, tool stations: 8, clamping devices: 8, machine dimensions X/Y/Z: approx. 11250mm/3400mm/2950mm, weight: approx. 7400kg, operating hours according to production planning system: approx. 42200h. The machine has no hour counter. Documentation available. An on-site inspection is possible. Chjdpfx Aboy Aafxerod

Condition: used, DALLAN Rollforming machine | Omega profiles 60mm & 80 mm With 11 forming stations, fully equipped and currently set up for Omega 60 mm, the line includes additional tooling for Omega 80 mm profiles. Chedpfxoxugf He Abred This machine is complete, in excellent condition. DALLAN rollforming line with 11 forming stations: · Maximum sheet width: 300 - 350 mm · Controls: Dual console · Shaft diameter: 60 mm · End unit: Integrated cutting station · Current setup: Configured for classic Omega 60 mm, includes tooling for Omega 80 mm · Idle decoiler · Tooling box (approx. 1,000 kg) for producing other profile types · Dimensions: 10,000 x 1,400 x 1,600 mm (L x W x H) · Weight: 10 tons Maximum sheet width: 300 - 350 mm Controls: Dual console Shaft diameter: 60 mm End unit: Integrated cutting station Current setup: Configured for classic Omega 60 mm, includes tooling for Omega 80 mm

Condition: new, Year of construction: 2026, functionality: fully functional, total width: 2,300 mm, total length: 9,000 mm, total height: 2,300 mm, overall weight: 9,000 kg, Mobile Roll Forming Machine for Frameless Steel Arch Buildings Automatic Production Line for Self-Supporting Steel Hangars and Arch Roofs The mobile roll forming machine is designed for the on-site production of self-supporting curved steel panels used for the construction of frameless steel buildings, arch hangars and self-supporting metal roofs. The technology makes it possible to construct large-span steel buildings without a conventional internal steel frame. Steel coil is formed into a structural profile, cut to the required length and then curved to the required building radius. Several curved panels are connected together using a special seaming machine to form a strong, continuous and self-supporting arch structure. The equipment can be used for the construction of: frameless steel hangars aircraft hangars agricultural buildings grain and machinery storage buildings warehouses industrial buildings workshops garages livestock buildings sports facilities self-supporting steel roofs temporary buildings military and logistics storage facilities Mobile Production Directly at the Construction Site One of the main advantages of this technology is the possibility of producing the complete structural panels directly at the construction site. The main forming and curving equipment is installed on a mobile trailer chassis. The machine can therefore be transported to the building site, where steel coils are converted into finished structural arch panels. This is particularly important for long panels that would otherwise be difficult or expensive to transport. The supplied machine has two axles and eight tyres intended for movement around the construction site. Production Process The complete production process consists of several stages: Steel Coil → Decoiling → Straight Profile Forming → Cutting to Length → Curving → Panel Seaming → Lifting → Installation The supplied technical manual describes the machine as a combination of a roll forming section and an arch bending section, with electrically driven forming and bending and hydraulic cutting. Main Technical Specifications Parameter Specification Machine type Mobile arch sheet roll forming line Application Frameless / self-supporting steel buildings Feeding width 1000 mm Effective profile width Approx. 610 mm Material thickness 0.8–1.5 mm Forming stations 13 + 1 Straight panel forming speed Up to 15 m/min Arch panel forming / curving speed Up to 13 m/min Seaming speed Approx. 6 m/min Forming motor 7.5 kW Curving / bending motor 5.5 kW Cutting motor 4.0 kW Additional drive 3.0 kW Total installed motor power Approx. 20 kW Cutting system Hydraulic Cutting tool material Cr12MoV, heat treated Roll material 45# steel, chromed and hardened Roller hardness HRC 58–62 Control system PLC Machine dimensions Approx. 9000 × 2230 × 2200 mm Machine weight Approx. 9000 kg Chassis 2 axles / 8 tyres Different Profile Sizes Available The machine can also be manufactured for different structural profile dimensions according to the required building span and application Available configurations may include different: coil feeding widths finished profile widths profile depths steel thicknesses Chedpoztwx Ujfx Abrod arch radii building spans For example, depending on machine configuration, profiles can be designed for relatively small buildings as well as large-span self-supporting arch structures

Condition: used, Roll Forming Line for Drywall and Zinc-Coated Door Frame Profiles General Description: Complete roll forming line designed for the production of zinc-coated steel profiles used in drywall structures and door frame systems. The machine processes galvanized steel strips with thicknesses typically ranging from 0.6 mm to 1.0 mm, featuring quick roller adjustment depending on the required profile type. Profiles Produced - Drywall Profiles: • Galvanized Tracks: width 57 mm and 77 mm, height 35 mm, sheet thickness 0.6 mm • Galvanized Studs: 39×55 mm and 39×75 mm, sheet thickness 0.6 mm • U-Shaped Profiles for False Ceilings: 27×60×27 mm, sheet thickness 0.6 mm • Offset Profiles for False Ceilings: 20×29×28 mm, sheet thickness 0.6 mm - Zinc-Coated Door Frame Profiles (10/10 mm): • Complete range from ART. 201 to ART. 217, including L, U, Z and special shapes • Variable dimensions: widths from 20 to 46 mm, heights from 15 to 31 mm, customizable configurations available Technical Features • Material thickness: 0.6 – 1.2 mm • Strip width: variable, depending on profile • Number of forming stations: 19 Chodpsxnmyqefx Abred • Rollers: hardened and ground steel rollers • Drive system: independent motorization for each roller group • Feeding speed: adjustable • Cutting unit: automatic flying shear or saw • Optional units: punching, slotting, or quick-change tooling systems

Condition: good (used), Year of construction: 1996, Offer 25468 Sheet – Profiling Line for Shelf Panels Technical Data: - Shelf panel width approx. 250 mm - Material thickness 1.25 mm - Profiling unit with 16 roll forming stations - Hydraulic punching unit - Straightening unit, make DREHER - Motorized decoiler CAMU, load capacity approx. 1.5 t - Control panel - Space requirement / footprint: 14 x 1.5 m Chjdpjxxvq Tsfx Abred - Weight approx. 10 t

Condition: used, Year of construction: 2006, API tube mill 355mm x14mm (A3801) is line to produce pipes for petrol industries so can be perfect solution for your company to grow up API tube mill (Made in China), Forming machine is made in Japan OD 114–355mm wall thcikness: 4-14.3mm steel grade: N80 tube length:6-15m standard: API 5CT N80 scope of supply: – slitting line; – tube mill; – two end facing machines; – two hydro testers; – 1 tube straightening machine, rolls (OD 114.3, 139.7, 219.1, 273.05, 323.9, 339.72 , 355.6mm) machine was made in 2006, stopped running in 2016. Chodpev Hcwtsfx Abrsd used seam annealer and HF welder, brand: Thermatool. Used slitter, Chinese brand. thickness: 4–14mm, N80, Q235, hot rolled steel. max coil width 1600–1700mm. 2+5 leveler DC motor: 55kw slitter DC motor: 160kw scope of supply: – coil car; – uncoiler (with 4 colums); – hold down roll; – peeler table; 2+5 leveler; – shear; – conveyor and loop; – guiding device; – slitter; – tension unit; – recoiler with support arm; – coil car; – approximate 12 slitting blades; – electric cabinet, hydraulic system. slitter is for tube mill

Condition: ready for operation (used), Year of construction: 1993, A Dreistern roll forming machine is offered. Main drive power: 9.2kW, production direction: right to left, roll shaft diameter: 30mm, roll shaft connection: 20mm, tooling width of roll stand type 1: 135mm, center distance of type 1: 130mm, adjustment range of type 1: 60mm-100mm, tooling width of roll stand type 2: 210mm, center distance of type 2: 260mm, adjustment range of type 2: 80mm-130mm, control system: Siemens SIMATIC HMI. The gearbox has been fully overhauled. Inspection by appointment is possible. Codpfx Ajzta Edebrshd

Condition: used, Year of construction: 1982, sheet width 480 mm plate thickness 3 mm stations 13 weight of the machine ca. 11 t dimensions of the machine ca. 15,x2 m Number of stations 13 Number of straightening stations 1 Waves 60 mm Center distance, horizontal 310 mm Center distance, vertical 110 - 250 mm Speed approx. 11 m / min. Connected load approx. 20 kW Uncoiler (without drive) - Coil- , inside 508/610 mm - Coil weight 3 t Flying hydraulic scissors Roller set for hat profile The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. Codpoyqtx Hofx Abrehd About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team

Condition: used, Stainless steel welding line MOD.70/120, made OLIMPIA 80 with tricathode welder & Seam bead roller & Orbital polishing Cjdpfx Asvtn H Tobrehd Specifications: - Diameter : 35 – 120 mm - Thickness : 0.7 – 3.5 mm - Length : 3 – 6 m Tube diameter: 35 – 120 mm Thickness: 0,7 – 3,5 mm Tube length: 3 – 6 m

Condition: ready for operation (used), Year of construction: 1989, - USED - ROLL FORMING MACHINE Codpjzqwf Nefx Abrshd STEPS: N. 20 WEIGHT: 25000 Kg OVERALL DIMENSIONS: 7300 x 2400 x 1500 mm NOTE: PROFILE: WIDTH FROM 85 mm TO 670 mm; LENGTH FROM 2000 TO 5000 mm; THICKNESS FROM 0,6 TO 1,5 mm IN AUTOMATIC; No 5 4-STEPS HEADS; FORMING LINE FOR CABLE TROUGHS AND CABLE TRAY COVERS PRODUCTION; EQUIPPED WITH LOADING/UNLOADING ROLLER CONVEYORS

Condition: ready for operation (used), Year of construction: 1994, A Schüco profile rolling machine for the thermal separation of aluminum profiles in window, door and façade construction is available. Processing speed: 45m/min, control speed: 15m/min, max. profile height: 400mm, max. profile width: 250mm, max. insulating bar width: 300mm, machine dimensions X/Y/Z: approx. 2700mm/800mm/1650mm, weight: approx. 900kg. Including automatic insulating bar feeder, safety cage/alignment roller set, roller conveyor and roller conveyor extension. Documentation available. On-site inspection is possible. Chsdpswtg Hwjfx Abrod

Condition: new, Year of construction: 2026, Automatic Roll Forming Line for Light Gauge Steel Frame Production This automatic roll forming line is designed for manufacturing Light Gauge Steel (LGS) and Cold Formed Steel (CFS) structural profiles used for steel frame houses, modular buildings, commercial buildings and prefabricated construction systems. The production line automatically performs feeding, leveling, punching, roll forming, profile marking and hydraulic cutting according to digital production data. It is an ideal solution for manufacturers of: Light Gauge Steel structures Steel frame houses Prefabricated buildings Modular buildings Tiny houses Commercial steel structures Residential steel framing Cold formed steel construction systems Flexible Machine Configuration The roll forming line can be supplied in two different configurations depending on production requirements. Fixed Profile Machine Designed for manufacturers producing one profile size with maximum productivity and simplified machine setup. Multi-Profile Roll Forming Machine An adjustable roll forming system capable of producing several profile widths on one machine by changing the roll forming configuration. This solution provides greater production flexibility while reducing investment costs compared with purchasing multiple dedicated production lines. Complete Automatic Production Process The machine automatically performs the following operations: Coil feeding Strip leveling Servo punching Hole punching Slot punching Service hole punching Roll forming Profile identification marking Hydraulic cutting to length Finished profile discharge The production line is designed to work with professional steel frame design software. The operator imports production data generated from a building design into the machine control system. Based on this information the machine automatically manufactures every structural member including: wall studs tracks floor joists roof trusses rafters beams structural reinforcements Each component is produced with the correct length, punching pattern and identification marking required for final assembly. Automatic Profile Marking Each profile can be automatically marked during production. Typical marking information includes: Profile number Wall identification Member position Assembly reference Project identification Automatic marking significantly simplifies profile sorting and speeds up on-site assembly. Instead of manually identifying every component, installers receive a complete production kit with every profile clearly identified. Automatic Punching System All punching operations are synchronized with the roll forming process to achieve high accuracy and repeatability. Main Advantages Fully automatic production Computer controlled manufacturing Automatic profile marking Servo punching system Hydraulic cutting High dimensional accuracy Reduced material waste Fast production Cjdpfx Abszrt Ivorjhd Flexible profile sizes Suitable for custom house projects Reduced manual labour Easy assembly thanks to profile identification Applications Technical Specifications Typical options include: Single-profile roll forming machine Multi-profile adjustable machine Automatic profile marking Servo punching Hydraulic cutting Automatic decoiler Hydraulic decoiler Computer control system Production management software compatibility

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: 0630, type of input current: three-phase, input voltage: 400 V, coil weight: 6,000 kg, overall weight: 12,000 kg, Machine available immediately. We are offering a new TR32 trapezoidal roll forming machine. The machine is new and ready for collection. Type: TR32 Year of Manufacture: 2026 Serial Number: 0630 Weight: 12,000 kg Maximum power: 12 kW Supply voltage: 3x400 V Supply frequency: (50–60) Hz THE MACHINE INCLUDES: - Electric decoiler with manual tension release, manually operated, capacity Q=6,000 kg; - Sheet metal feed with circular (rotary) knives - Profiling unit - Electromechanical guillotine - 6-meter sheet metal stacker + 6-meter transport cart - Control cabinet - Safety guards If you have any questions or require additional information, please send us a message or call us. Chedpfxszl A I Sj Abrjd

Condition: ready for operation (used), Year of construction: 1998, Travel X/Y/Z: 3200mm/300mm/250mm, speed: 18000rpm, motor power: 7.4kW, tool holder: SK30, tool positions: 8, tool changer: turret, materials processed: aluminum/steel (max. 5mm thick)/PVC (steel-reinforced and unreinforced), wood and plastics. Documentation available. On-site inspection is possible. Chsdpfx Absuzlfasrjd

Condition: excellent (used), Year of construction: 2005, 19 stations design: cassette shaft Ø: 30 mm strip width: 200 mm Cjdsh Tm Rajpfx Abrshd strip thickness: 1 mm