Condition: excellent (used), functionality: fully functional, Used Sandvik CV217 VSI Crusher Year 2012 All New Wear Parts Shotblasted and Painted 185kW Electric Motor Complete With Electric Control Panel Complete With Support Legs Approx Weight 9,5000 Kgs Rsdpjy Swimsfx Ai Hju Excellent Condition

Year of construction: 2013, operating hours: 700 h, condition: excellent (used), functionality: fully functional, Used Westeria Airtrack 1 Tracked Windsifter Year 2013 700 Hrs Redpeyyxx Esfx Ai Heu 2000mm wide feed belt / rotating drum Heavies Belt / Lights Belt Volvo Diesel / Electric Generator Driven 19,000 kgs Very Nice Unit Fully Serviced & Ready To Go Straight To Work

Year of construction: 2017, operating hours: 6,100 h, condition: excellent (used), functionality: fully functional, Year 2017 6100 Hrs 1 Owner JCB Engine Rodpfexz R Tnex Ai Hou Fitted With 0-20 / 40mm Deck Extremely Well Looked After Unit

Condition: ready for operation (used), * Brand: Kleemann * Beltwidth: 1400 mm. * Driving: 15 kW Gearbox. Rodpfx Aieywm Sne Hou * on Stock: 1 piece

Condition: reconditioned (used), Year of construction: 2019, operating hours: 3,000 h, functionality: fully functional, pressing force: 70 t, year of last overhaul: 2025, Technical data packing press / can press / metal sheet press: Manufacturer unoTech GmbH Type UPAXX 70 Year of manufacture 2019 Operating hours approx. 3,000 hours Pressing force 700 kN at 315 bar Filling opening chute 420 x 1,250 mm (d x w) Channel cross-section (package dimension) 350 x 500 mm (h x w), length depending on material Drive power 30 kW Connected load 40 kW Power consumption, total 70 A Throughput capacity for empty beverage cans with: one pressing stroke approx. 1.7 t/hour two pressing strokes approx. 2.5 t/hour Redpfsy Urvaex Ai Hju Achieved compaction approx. 1200 kg/m³ Hydraulic oil tank capacity 850 l Press dimensions built up 8,000 x 1,600 x 2,500 mm (l x w x h) Transport weight press approx. 9.5 t Accessories: Oil cooler 1.5 kW, oil tank heater 1.5 kW, press box made of wear-resistant steel S355 Material properties: According to the manufacturer, this machine is suitable for pressing tin cans, metal sheet offcuts, sheet steel as well as aliminium, brass and copper waste. Condition of the baler: The packing press has been fully overhauled in our workshop. The press is in very good condition; please see the demonstration video following the overhaul. The machine sustained transport damage whilst being moved. The control cabinet was damaged and slightly dented by a forklift truck, and the main switch (on/off switch) was damaged. These damages are reflected in the significantly reduced sale price and must be repaired by the buyer at their own expense. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2002, operating hours: 44,590 h, functionality: fully functional, pressing force: 200 t, filling opening width: 2,000 mm, filling opening length: 1,020 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,000 kg, oil tank capacity: 3,100 l, year of last overhaul: 2026, volume flow: 795 m³/h, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 112 Year of construction 2002, partially refurbished in December 2025 Rodjy Uruvopfx Ai Heu Operating hours 44,590 hours, stand December 2025 Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Machine weight baler approx. 50,8 tons Scope of delifery: 1 piece baler MACPRESSE, type 111A 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Comments: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Hydraulic oil tank emptied and cleaned • Oil and air filters replaced • New hydraulic oil filled • All hydraulic hoses replaced • Press ram dismantled, broken down into individual parts, mechanics made operational • Front two main rollers replaced • Knives on the press ram replaced • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, complete seal set replaced • Counter knife in the frame replaced • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame on the left and right replaced. • Worn press base cut out, base plate replaced with wear-resistant HARDOX steel. • Binding and twisting unit dismantled, broken down into individual parts, mechanics made functional, all twisting shafts and ball bearings replaced. • All wire rollers in the needle heads replaced • Wire knives cleaned and readjusted, chains greased and tensioned • All wire deflection rollers made operational • All door contact switches replaced • Wirbulator device dismantled, disassembled and made operational • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode, see video for the machine function test. The documentation (BA, CE, electrical/hydraulic circuit diagram) is complete. Viewing is possible by appointment. We accept no liability for the technical specifications or any errors.

Condition: used, Technical data feed hopper with hydraulic moving floor and bag opener for recyclables from yellow bags and residual waste: Manufacturer BRT HARTNER GmbH Type HP5-3035 Year of construction 2015 Hopper volume 30 m³ Drive line 17.5 kW Dimensions in current state 13,200 x 3,050 x 4,350 mm (l x w x h) Condition of the machine: The feed hopper with bag opener was used at a large recycling plant, where recyclable materials from yellow bags or commercial waste were tipped into the hopper using wheel loaders, the bags were opened using the bag opener, and the recyclable materials were transported to a sorting plant or the commercial waste was transported in measured quantities for further processing. The system functioned flawlessly until it was dismantled and replaced with a larger system with higher throughput capacity. The machine was dismantled into individual parts in our workshop, partially overhauled, reassembled, and tested during operation. The following overhaul work was carried out and the following spare parts were replaced: Dismantling of the feed hopper and bag opener into individual parts. Cleaning, partial sandblasting, priming and painting of the steel parts. Various wear and cover plates were newly manufactured and installed. Cutting off the worn ends (approx. 40cm) of the push floor pipes. Welding on the new pipes and smoothing the push floor pipes. Replacement of all plastic sliding plates for the hydraulic push floor. Rsdpfey Urtfox Ai Hsu Removal of the hydraulic unit from the push floor, emptying of the hydraulic oil tank, replacement of the oil filters, refilling with new hydraulic oil. Replacement of the three hydraulic blocks, all valves, the oil sight glass and all hydraulic hoses from the hydraulic unit. The seal kit and hydraulic hoses were replaced on all three hydraulic cylinders of the push floor. All six limit switches (proximity sensors) on the push floor were replaced. The conveyor chains on the left and right of the scraper conveyor were replaced. Seven carrier bars on the scraper conveyor were replaced. The drive motor for the ripper blades was replaced. All nine pneumatic cylinders for the pressure pipes were replaced. All pneumatic lines and connections were replaced. All of the plastic sliding plates for the hydraulic operation of the bag opener were replaced. The bag opener can be moved vertically so that the system can also be used for commercial waste or residual waste without the bag opener. The side impact protection plates on both sides were replaced. Various wear parts of the bag opener have been replaced. The entire system has been rewired and reconnected. The system control in the control cabinet has been retrofitted by the manufacturer BRT Hartner to a self-sufficient individual control system and the standard programme has been reloaded into the control system. The system has been commissioned and tested by the manufacturer BRT Hartner, see the function video. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: refurbished (used), “SGM DIS 100” for Sale Manufacturer: SGM Magnetics Type: DIS 100 Belt widthness: 1.000 mm (New belt) Included: Rodpfx Asy U N Exoi Hou – New Control-unit Eddy Current Separator is overhauled, sandblasted and painted.

Condition: good (used), 6 Pcs “Smulders” for Sale Manufacturer: Smulders Waste Technology – 5 Pcs. with 200mm. wide Stainless steel belt. Rsdpfxjy Um N Ue Ai Hju – 1 Pc. with 400mm. wide Stainless steel belt. Also air blowers in stock.

Condition: ready for operation (used), Year of construction: 2008, Brand: HSM Rodpfezaqymjx Ai Heu Model: V-Press 1160 plus Year of manufacture: 2008 Pressing force: 532 kN Voltage: 400 Max. bale weight: up to 550 kg (depending on the material) Bale dimensions: 120 x 110 x 120 cm Machine weight: 2403 kg Machine dimensions: 180 x 157 x 298.5 cm Feed opening dimensions: 119.5 cm × 65 cm Condition: very good! Video of the machine in operation available upon request. Transportation is also possible.

Condition: excellent (used), N.PREVIERO shredder Redpfx Aisza Epio Hju Blade: 1,000 Engine: 170 kW Complete with conveyors and dosing systems.

Year of construction: 2010, condition: good (used), 2 SICON shredders Year 2010 Redpfx Aeiz Tm Iei Hsu The electrical cabinet is missing Price 15 000€ each 4 densimetric tables : 8 000€ each

Condition: excellent (used), Year of construction: 2021, operating hours: 44 h, functionality: fully functional, HSM V-Press 860 plus vertical baling press, year of manufacture 2021 Technical data: Manufacturer: HSM Type: V-Press 860 plus Year of manufacture: 2021 Operating hours: 44 Pressing force: 60 t Drive power: 4 kW Feed opening: 1195 x 645 mm Feed height: 1114 mm Bale size: approx. 1200 x 1200 x 780 mm Bale weight: 480 kg Tying: manual Theoretical cycle time in idle mode: 25 s Theoretical pressing capacity: 12 m³/h Rodpfx Aey Uvt Aoi Heu Dimensions: 1800 x 1253 x 2990 mm (W x D x H) Weight: 2213 kg Materials: film, paper, cardboard Note: The press is in good condition. It has been inspected and tested by us. A video can be found on our website or YouTube channel. Please note: All technical data refers to the manufacturer's specifications. We assume no liability for the information provided or any errors that may occur. The offers are non-binding, subject to prior sale and may be revoked at any time. Inspections are possible by arrangement. The sale takes place at our location, without warranty. Our payment terms are 100% prepayment.

Condition: used, Year of construction: 1983, total width: 750 mm, total height: 900 mm, total length: 2,400 mm, Empty weight: 500 kg - Year: 1983 - Documentation available: No Rodpfx Aisxalyye Heu - CE certificate present: No - Transport dimensions: 2400mm x 750mm x 900mm (l x w x h) - Transport weight [kg]: 500kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 2018, total length: 2,400 mm, total height: 1,000 mm, total width: 1,200 mm, Colour: Red Empty weight: 1.000 kg - Year: 2018 - Documentation available: No - CE certificate present: No - Serial number: 600-797 Rodpfx Aey Tmu Uei Heu - Main motor power [kW]: 22,2 - Rotation speed [rpm]: 1770 - Rotor width [mm]: 400 - Number of shafts [pcs.]: 2 - Opening width [mm]: 385 - Opening length [mm]: 93 - Sieve perforation [mm]: 20 - Number of fixed knives [pcs.]: 18 - Transport dimensions: 2400mm x 1200mm x 1000mm (l x w x h) - Transport weight [kg]: 1000kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, year of last overhaul: 2026, volume flow: 930 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Rsdpfx Aoy S Ru Asi Hou Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2015, operating hours: 30,143 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 570 kg, overall weight: 20,000 kg, oil tank capacity: 600 l, year of last overhaul: 2026, volume flow: 800 m³/h, Technical data baler: Manufacturer Presona AB, Sweden Type LP 60 VH1 Year of construction 2015 Total operating hours, 30,143 hours, as of July 2025 Effective pump running time onl 6,527 hours, as of July 2025 Number of pressed bales 115,193 bales, as of July 2025 Press force pre press 25 t Main press force 60 tonnes Specific pressing force 73N/cm² Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Theoretical throughput capacity 800 m³/hour Throughput capacity under operating conditions 350 m³/hour Bale dimensions 1,100 x 750 mm Drive power 37 kW Tying 5-fold vertical, fully automatic Throughput capacity with a Bulk weight of 50 kg/cbm 11 to 14 tonnes/hour Rjdpjy S Rtlefx Ai Heu Bale weights 420 to 570 kg, depending on material Hydraulic oil tank volume 600 litres Baler dimensions assembled with hopper 10,100 x 3,750 x 4,310 mm (l x w x h) Transport dimensions excluding press 10,100 x 2,400 x 3,000 mm (l x w x h) Machine weight press approx. 20 tonnes Condition of the press: The press was partially overhauled in our workshop and then tested in manual and automatic mode. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Grease cartridges of the automatic roller lubrication system replaced Slide rails cut out from the press floor in the press room Underbody reinforced with welded sheets New HARDOX slide rails welded in Wire station with deflection rollers for the lower wire cleaned and made operational Slide rails cut out from the floor in the press channel New HARDOX slide rails welded in Both side walls of the press channel dismantled, derusted Worn side wall plates cut out Complete side walls covered with new wear plates and welded Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Machine checked, general maintenance work carried out and press tested in manual and automatic mode Comments: The press is sold without a conveyor belt and without wire stations. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 1996, functionality: fully functional, pressing force: 170 t, filling opening width: 1,020 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, overall weight: 40,000 kg, oil tank capacity: 3,000 l, year of last overhaul: 2025, volume flow: 750 m³/h, For sale is a used baling press system consisting of a chain belt conveyor for underfloor operation, with a feed hopper, a hydraulic pre-compactor with ruffler, a MACPRESSE 111A baling press, two complete wire drawing frames with 5 wire reel stands each, without wire. Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 111A Year of construction 1996, refurbished in 10/2024 Press power main press 170 tons Specific press capacity 14 kg/cm² Feed channel 1,800 x 1,020 mm Filling volume 2,5 cm³ Theoretic throughput rate 750 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 55 kW Tying system 5-fold horizontal, full automatic Throughput rate at a approx. 30 up to 35 tons/h, depends on material Volume hydraulic oil tank 3,000 l Transport dimensions of press with new machine feets 113,700 x 2,300 x 2,900 mm (l x w x h) Machine weight baler approx. 40 tons Comments: The baler was partially overhauled in our workshop and tested after completion of the work, please look at our functional video. The system was previously used to bale paper and cardboard from municipal collections. The contract was awarded elsewhere after the end of the contract period, so the complete system is for sale. The overhaul work carried out and the spare parts replaced can be found in the detailed photo documentation and in our quotation. Rsdpfey S Rqwox Ai Hsu The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Technical data conveyor belt: Manufacturer Wagensfeld B.V. Type chain belt conveyor 1700 mm Year of construction 2017 Drive power 7.5 kW Belt speed 14 m/minute Length of infeed conveyor 6,900 mm Length of ascending belt 12,885 mm Length of gooseneck 1,747 mm Overall length 21,271 mm Pitch 32° Effective width 1,644 mm Height of drive shaft above ground 5,777 mm Wall height of feed conveyor 500 mm Wall height of ascending conveyor 880 mm Steel flights height 40 mm Distance between flights 1200 mm Transport dimensions conveyor disassembled 15,005 x 2,503 x 2,435 mm (l x w x h) Pit dimensions 11,500 x 2,700 x 1,015 mm (l x w x d) Remarks: The chain belt conveyor, built in 2017, was later made to fit the baler during the last installation of the baler in the Netherlands and is newly installed. The conveyor belt is in good, operational condition and has therefore not been overhauled. An installation drawing with the pit dimensions is available. Scope of delifery: 1 chain belt conveyor, Wagensveld B.V. 1 piece feed hopper with pre-compressor flaps 1 piece wirbulator 1 baler MACPRESSE, type 111A 2 wire drawing frames with wire reel stands, without wire 1 operating manual with CE declaration, electrical and hydraulic circuit diagram

Condition: excellent (used), Year of construction: 2019, Wanrooe Grinding Line Year 2019 Consisting of a single shaft crusher, a conveyor elevator of approximately 4 meters with suction installation Rsdpfowqtuisx Ai Heu

Condition: good (used), functionality: fully functional, “Steinert NES 150 210 E 6119” for Sale Rodpfx Aiey S Tv No Hju Manufacturer: Steinert Type: NES 150 210 E 6119 Belt widthness: 1.500 mm (New belt) With control-unit. Overhauled, balanced, sandblasted and painted.

Condition: ready for operation (used), Year of construction: 1994, Brand: HSM Model: 155 VL Redpfx Aoy Uwnnoi Heu Year of construction: 1994 Pressing force: 157 kN Voltage: 400 Max. bale weight: 250 kg Bale dimensions: 110 x 70 x 95 cm Machine weight: 950 kg Machine dimensions: 144 x 100 x 234 cm Feed opening dimensions: 110 x 59 cm

Condition: good (used), Year of construction: 2018, operating hours: 1,011 h, functionality: fully functional, Shredder GROSS, Model GAZ 82 S, Year of Manufacture 2018 Technical specifications: Manufacturer: GROSS Apparatebau Model: GAZ 82 S Year of manufacture: 2018 Operating hours: 1,011 Drive power: 37 kW Feed opening: 800 x 1200 mm Hopper volume: 1 m³ Rotor diameter: 368 mm Rotor length: 800 mm Rotor speed: 60–120 rpm Extraction nozzle diameter: 200 mm Transport dimensions: approx. 2100 x 1700 x 2600 mm (LxWxH) Weight: approx. 2,600 kg Rodpfxex Uz N Aj Ai Hou Suitable materials: Wood, cardboard, plastics Accessories: Hopper Remarks: The shredder is in good condition. It has been inspected and tested at our location in 28816 Stuhr. You can find a video on our website or YouTube channel. Inspections, including under power, are possible at any time by appointment. On request, we can also carry out tests with your material for a handling fee. If you have any questions about the machine, we will be happy to answer them by phone from Monday to Thursday from 08:00 to 14:00. On Fridays, we are available from 08:00 to 13:00. Please note: All technical data are based on information provided by the manufacturer. We accept no liability for the stated details or for any errors. This offer is non-binding, subject to prior sale, and may be withdrawn at any time. Inspections are possible by arrangement. Sale is ex works upon advance payment, without warranty or guarantee.

Condition: good (used), Year of construction: 2015, operating hours: 1,932 h, functionality: fully functional, Baler Presto CC 50 M, semi-automatic, year of manufacture 2015, with lift-and-tilt device Technical Specifications: Manufacturer: Presto Model: CC 50 M Year: 2015 Operating hours: 1,932 Pressing force: 50 t Cycle time: 52 s Drive power: 7.5 kW Filling opening: 1030 x 1100 mm Filling volume: 0.85 m³ Tying: 3-fold, wire, manual Throughput depending on bulk density: 35 kg/m³ – 1.3 t 60 kg/m³ – 1.7 t 100 kg/m³ – 2.2 t Bale dimensions: 750 x 1100 mm Bale weight: 300 kg Dimensions: 4705 x 1680 x 2540 mm (LxWxH) Machine weight: approx. 4,000 kg Materials: Paper, cardboard, film Redpfxeyz R Etj Ai Hju The operating manual is available in German. Note: The machine is in good condition. It has been inspected and tested at our premises in 28816 Stuhr. The video is available on our website or YouTube channel. Please note: All technical data is based on information from the manufacturer. We accept no liability for the details provided or for any possible errors. Subject to prior sale; offer is non-binding and may be revoked at any time. Inspections are possible by arrangement. Sale is ex works against advance payment, without warranty or guarantee.

Condition: good (used), Year of construction: 2017, operating hours: 1,640 h, functionality: fully functional, Baler Presto CC 40 M, Year of manufacture: 2017 Technical Specifications: Manufacturer: Presto Model: CC 40 M Year of manufacture: 2017 Pressing force: 40 t Cycle time: 34 s Drive power: 15 kW Feed opening: 1080 x 1100 mm Feed volume: 0.85 m³ Binding: 4-fold, polyester strapping, manual Throughput rate at bulk density of: 35 kg/m³ - 1.8 t/h 60 kg/m³ - 2.5 t/h 100 kg/m³ - 3.1 t/h Bale size: 750 x 1100 mm Bale weight: 400 kg Dimensions: 3650 x 1590 x 2010 mm (LxWxH) Redpfx Aisyz R Hqj Hou Machine weight: approx. 3,800 kg Materials: Paper, cardboard, film The baler is in good condition. It has been inspected and tested by us. A video can be found on our website or YouTube channel. Operating instructions and CE declaration are available. Note: Channel discharge is fully automatic and regulated. Please note: All technical data is based on the manufacturer's information. We do not accept liability for the information provided or any possible errors. This offer is non-binding, subject to prior sale, and may be revoked at any time. Inspections are possible by appointment. Sale is ex-works, prepayment required, without warranty or guarantee.

Condition: ready for operation (used), Year of construction: 1979, functionality: fully functional, Baler Paal Pacomat II, Year of Manufacture 1979 Technical Specifications: Manufacturer: Paal Model: Pacomat II Year of Manufacture: 1979 Drive Power: 11 kW Pressing Force: 27 t Channel Cross Section: 700 x 1000 mm Filling Opening: 1000 x 650 mm Throughput: approx. 60/115 m³/h Bale Size: 700 x 1000 mm Bale Weight: up to 400 kg Machine Dimensions: approx. 7000 x 2000 x 2000 mm (LxWxH) Machine Weight: approx. 5200 kg Materials: Paper, Cardboard, Film Redoyz Saljpfx Ai Hju Remarks: The machine is in fully functional condition. It has been inspected and tested at our site in 28816 Stuhr. You can find the video on our website or our YouTube channel. Viewings, including under power, are possible at any time by appointment. Please note: All technical details are based on information provided by the manufacturer. We accept no liability for the accuracy or possible errors. Offers are subject to change, prior sale reserved, and may be revoked at any time. Viewings are possible by prior arrangement. Sale is ex works, without warranty or guarantee. Our payment terms require 100% advance payment.