Machining center

CONTUR M-1600

Condition: as good as new (ex-display), Year of construction: 2024, General Ppodpfjur Ng Ujx Aaajp Tool magazine : 2x chain magazine with 32 stations each Rapid traverse in X/Y/Z : 48 m/min Traverse path X/Y/Z : 800/900/620 mm Spindle Technology : Direct drive Speed : 15.000 rpm Tool holder : HSK-A63 NC rotary table Technology : Swivel rotary table with torque drive, made by Kessler A-axis : +/- 120 C-axis : 360° Clamping surface : ø800 mm Table load (max.) : 1,000 kg Workpiece dimensions (max.) : ø800 x 500 mm Equipment Distance measuring system : Direct (glass scales) in all axes Chip management : Chip conveyor Coolant management : IKZ system with filter and high pressure, 18 bar Workpiece measurement : Touch probe, Heidenhain TS 740 Tool measurement : Laser, BLUM Set-up mode : Electronic handwheel Additional equipment : Spindle cooler

Condition: ready for operation (used), Year of construction: 2015, Used Timesavers Deburring Machine 42-Series-1350-WRB Technical Specifications: Year of manufacture: 2015 Condition: refurbished (2026) The machine is under power and can be inspected by appointment! Max. working width: 1350 mm Abrasive belt dimensions (W x L): 1380 x 1900 mm Antistatic device Maximum weight: 100 kg Electrical connections: 400 V Frequency: 50 Hz 1st Unit: Contact roller Ø 180 mm Contact roller 55° Shore NI, grooved Pneumatic oscillation Fine adjustment by raising/lowering the contact roller Dial gauge Main motor 15 kW Processing speed: 11 m/s, in feed direction 2nd Unit: Rotary brush unit 8 brushes Ø 350 mm Motorized height adjustment with tip switch Drive motors: 5x 1.5 kW Rotational speed of the unit, frequency controlled Processing speed: 6 – 17 m/s 3rd Unit: Wall-mounted parts cleaning brush Podpfxjyk U Szo Aaaepp Feed: Fixed vacuum table Feed belt, flat and perforated, oil- and heat-resistant, flame-retardant Feed motor 2.6 kW, frequency controlled, 0.6 – 8 m/min Tip switch for forward/reverse feed belt Motorized height adjustment of table 0.18 kW, 0 – 100 mm, digital display Pressure rollers: Spring-loaded pressure rollers Ø 50 mm, with limit switch at the front Vacuum pump 15 kW Machine built to CE standards Main switch, operating hours counter Sound pressure level: ± 80 dB Machine weight: 6,200 kg Extraction and/or installation service can be offered on request!

Condition: new, Year of construction: 2023, functionality: fully functional, type of input current: three-phase, travel distance X-axis: 1,500 mm, travel distance Y-axis: 750 mm, travel distance Z-axis: 610 mm, workpiece weight (max.): 1,500 kg, total height: 24,920 mm, total length: 43,670 mm, total width: 30,700 mm, table length: 1,600 mm, table width: 700 mm, spindle motor power: 11 W, rapid traverse Z-axis: 24 m/min, rapid traverse X-axis: 30 m/min, rapid traverse Y-axis: 30 m/min, spindle nose: Iso 40, spindle speed (max.): 8,000 rpm, spindle speed (min.): 40 rpm, tool diameter: 75 mm, tool length: 250 mm, Equipment: documentation/manual, rotational speed infinitely variable, NEW vertical machining center "AWEA BM-1500 II" with FANUC 0i-MF Plus CNC Accessories present: 4th axis interface Air blow system Left side auger chip conveyors Ppodpfx Asrkn Iioaaop Coolant through spindle ( CTS ) at 20 bar Coolant gun Fairing bottom washing system 500 liter refrigerant collection tank Automatic power-off system Alarm light & work light

Condition: new, Year of construction: 2025, -Custom-Made Machines Tailored to Your Production Needs. -Our custom-made machines are meticulously designed and engineered to meet the unique demands of your production processes. Whether your focus is finishing, oxide removal, or radius edge rounding, these machines deliver outstanding precision and performance -Finishing: Achieve smooth, high-quality finishes on a wide range of materials, ensuring a consistently professional, polished appearance. -Oxide Removal: Effectively eliminate surface oxides to provide a clean, contaminant-free surface—essential for further processing or coating applications. -Radius Edge Rounding: Precisely round edges to your specified radius, enhancing both safety and the overall quality of your finished products. Customization Options Each machine is tailored specifically to your requirements, offering flexibility in: Processing Speeds: Adjustable to match your varying production demands. Special Features: Options include dust and fume extraction systems, adjustable pressure settings, and programmable configurations designed to optimize your workflow Psdpfohq Dbxjx Aaaspp Built for Durability. Constructed with longevity in mind, our custom machines are built to perform reliably through extended production cycles. Whether for small-scale projects or high-volume industrial applications, these machines provide exceptional results, year after year

Condition: as good as new (ex-display), Year of construction: 2025, working width: 1,100 mm, sheet thickness (max.): 100 mm, The 32 RB series offers the solution for manufacturers delivering premium-quality products. This top quality is achieved by a multi-rotating brush unit with four abrasive lamella brushes, which evenly deburr and perfectly round the edges of the metal. Multi-directional rotary brush deburring machine (RB) for consistent deburring and finishing of flat sheet metal parts. All-around processing in a single pass, providing the part's surface with a non-directional finish. Equipped with one (or more) abrasive belt units (W) for pre-deburring and final finishing. Pjdpsxw Ikcefx Aaaepp - Abrasive belt unit - Rotary brush unit (self-calibrating) - Abrasive belt unit

Year of construction: 2026, condition: as good as new (ex-display), Workbenches in Pro version Precise and careful processing Completely made of steamed, solid beech All important edges are rounded Environmentally friendly oiled surfaces Standard with tool drawer The two cylinder rods of the collets are precise and stable in a casting With smooth trapezoidal threaded spindle French front caliper with German rear caliper with linear Guide, two round bench dogs short, long, two round bench dogs drawer and loading in Finger hot dip galvanizing in rear caliper and by charging back 1915 mm long work surface without pliers Width/depth work surface without pliers 615 mm Working height 870 mm Length 520 mm front caliper Length 450 mm rear caliper Wide front caliper 70 mm Wide rear pliers 140 mm Span front pliers 190 mm Span back pliers 180 mm Span front clamp until the Middle Hook 225 mm Span back pliers until the Middle Hook 265 mm Plate thickness 50 mm Length 2120 mm (product) Width/depth (product) 790 mm Ppedjc Uydajpfx Aaaop Height 870 mm (product) Weight 91 kg (net) Location: Off the shelf 54634 Bitburg

Condition: excellent (used), Year of construction: 2010, functionality: fully functional, Tool Milling Machine Kunzmann WF4/3 with Heidenhain TNC 320 CNC Control – Excellent Condition, CE-Compliant, from Training Workshop! Technical Specifications: • Year of manufacture: 2010, Machine No. 347283 • Fixed angular table • Infinitely variable spindle speed up to 4,500 rpm • Infinitely variable feed in 3 axes from 0 to 2,000 mm/min • Rapid traverse X and Y axis: 5,000 mm/min Ppodexuppuspfx Aaaep Z axis: 4,000 mm/min • Travel X/Y/Z: 400/350/400 mm • Table size: 650 x 350 mm • Table load capacity: 250 kg • Vertical quill stroke: 60 mm • Vertical and horizontal quill – SK40 taper • Hydraulic clamping system • Weight approx. 1,800 kg • Space requirement approx.: 2.3 x 2 x 2 m • Drive power: 15 KVA Accessories and Equipment: • Heidenhain TNC 320 CNC control • Hydraulic clamping, vertical and horizontal • Automatic central lubrication • Spindle brake • Technical documentation, spare parts diagrams, control manuals and programming examples • Handwheels • Coolant system • Electronic handwheel HR410 About the Machine: Offered for sale is a Kunzmann WF4/3 tool milling machine with Heidenhain TNC 320 CNC control. This universal milling machine is in excellent condition and has seen very few operating hours. It comes from a facility where it was used exclusively for training purposes. The control is very user-friendly. Additionally, the machine features hydraulic clamping both vertically and horizontally. Changing from vertical to horizontal operation is very straightforward by swinging away the vertical head. The ways are regularly lubricated via the central lubrication system. The Kunzmann has been mechanically and electrically inspected by us. You are welcome to view and test the Kunzmann on-site under power. There are 7 units of Kunzmann WF4/3 with the TNC 320 Heidenhain milling machines available. The machines are available immediately.

Condition: as good as new (ex-display), Year of construction: 2023, Control : Heidenhain TNC 640 Pjdpfxot Dizvj Aaajpp Travels X : 1,020 mm Travels Y : 520 mm Travels Z : 610 mm Clamping surface (L x B) : 1,160 x 520 Table load : 750 kg Spindle Speed : 15,000 rpm direct Tool holder: SK40 (BigPlus) DIN69872 In general Tool changer : 30-stations Machine bed : Meehanite cast Repetitive accuracy : 0.008 mm Equipment Chip conveyor Coolant supply Elect. handwheel high pressure coolant

Condition: used, Year of construction: 1992, Automatic PET bottle blowing machine Manufacturer: SIDEL Type: SBO 4 S1 Year of prod. 1992 Capacity: 4,000 for 1.5 L / 2 L bottles Installed power: 150 kW Includes 1.5 L molds Ppjdpfx Aowa Rhrsaaop Preform feeder Technical condition: used machine, starts up, program is functional

Condition: used, Magnetic drill, hand drill -Magnetic base: Magnetor type PS 32 L -Drilling machine: AEG type HBE-IV - Recording: MK2 -Max. Drill: Ø 23 mm -Connection: 265V/200Hz -Dimensions: 700/300/H670 mm Podpfxefc R D Ae Aaaopp -Weight: 49 kg