Injection moulding machine

DEMAG

Condition: good (used), functionality: fully functional, Year of construction: 2014, laser power: 3,000 W, X Working area max.: 2500 mm Y Working area max.: 1250 mm Control: IndraMotion MTX Laser power: 3000 watts Standard equipment: Machine - Coordinate guide for high-precision machining - Stable, easily accessible C-frame - Linear magazine with 21 tool positions and 4 clamps - Drives with maintenance-free three-phase servo motors - Repositioning device with programmable hold-down device - Foot switch for clamp closing - Ball tables - 2 part flaps 500 mm x 500 mm - FocusLine - NitroLine - FastLine - Ejection cylinder for laser parts - Slag cone detection TRUMPF laser - TruDisk 3001 solid-state laser with 1 LLK outlet - Excitation via pump diodes - LLK according to standard layout (10m) - TruControl laser control 1000 - Cooling unit - Laser logbook function Cutting head - Solid-state laser compact cutting unit - ControlLine Punching head - Electro-hydraulic punching head - Rotatable mono tool holder - Tool length compensation - Programmable hold-down device (active / passive / repositioning) - Punch stroke counter and thread stroke counter - Spray lubrication of punch Pgedpfx Aowld Suedisw - Punch slug extraction - Calculation of filling level in the punching console - Level monitoring of thread forming and tool lubrication Control - Open control based on Rexroth IndraMotion MTX - Control panel with 17" touch control panel - Program management - Production plan - Integrated technology data - Teleservice via Internet - Programmable cutting gas pressure - Automatic switch-off with wake-up mode Data transfer - USB interface - RJ-45 network connection Safety - CE marking - Two-beam light barriers - Monitoring system for, among others Gas pressure, temperature, cooling water - Quick shutdown hydraulics - Protection against scattered radiation - Compact dust extraction system - MultiTool function - MultiBend function - Thread forming function - Engraving function - Deburring and rolling technology function - SoftPunch function - StripLine - Lowerable die - Spray lubrication die including level monitoring - Additional clamping claw - 4 pcs. Height-adjustable clamping claws - Vibration-damped installation - Chip conveyor with tilting container - Blow-out device for small parts - Warping detection SheetMaster - Unloading platform - Suction frame with 36 suction cups - Peeling suction cup - Vacuum sensors for each suction cup - Double sheet detector for double sheet control - Central lubrication - TRUMPF control based on Rexroth IndraMotion MTX - Automatic clamp closing machine - Loading and unloading parallel to production time - Peeling system including positioning aid medium format (2500x1250) - First additional suction cup package standard - Second additional suction cup package standard - Unloading monitoring laser parts GripMaster - Parts conveyor belt punching station - Parts conveyor belt laser station ToolMaster with 70 stations (only for punching operation) - ToolMaster set-up parallel to production time

Condition: excellent (used), Year of construction: 2023, operating hours: 1,851 h, functionality: fully functional, pressing force: 70 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 500 kg, overall weight: 17,000 kg, oil tank capacity: 70 l, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410 BS-22/50 Year of construction 2023 Pump operation hours 1,851 hours, as of July 24 Press power main press 70 t (a 70 tonne hydraulic cylinder is installed, special equipment) Specific press force 90,9 N/cm² (a 70 tonne hydraulic cylinder is installed, special equipment) Feed channel 1,400 x 1,000 mm Theoretic cycle time 13 sec Theoretic throughput capacity 266 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 22 kW Connected load 65 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 5,5 t/h bulk weight of 50 kg/cbm approx. 7,5 t/h bulk weight of 100 kg/cbm approx. 9,7 t/h Bale weight with a bale length of approx. 1.2 m up to 500 kg, depends on material SPS controller Siemens S7-1500 Operating panel Schneider Harmony Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 17 t Special equipment: Wear-resistant floor made of HARDOX steel Larger main hydraulic cylinder with 70 tonnes of pressing force Special press ram for pressing loose bulk materials with small grain sizes OptiCut XS system for lower cutting forces and higher throughput rates Special pressing piston for pressing "difficult" materials Psdou Thbxepfx Adisgw Technical data for the conveyor belt: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Deutschland Type KGF GB 1500 Year of construction 2023 Drive power 4.0 kW Belt speed approx. 0.3 m/second Length feeding conveyor 2,679 mm Length elevating conveyor 6,866 mm Length goose neck 1,272 mm Grade 35° Effecting width 1,400 mm Side wall height 800 mm Carrier height 50 mm Carrier distance 750 mm Belt quality EP 400/3, 3:1 (DIN quality N) Overall height 4,515 mm Overall transport dimensions11,148 x 2,502 mm (l x w) Technical data on the non-contact personal protection system: Manufacturer BOREMA Umwelttechnik AG, Switzerland Type APSS iBOR 22 Year of construction 2023 Condition of the press system: The entire system is in very good condition due to the short operating time of only 1,851 pump hours and the processing of only paper, cardboard and film. Scope of delivery: Avermann baler, type AVOS 1410 BS-22/50, incl. wire drawing stations and bale chute Avermann conveyor belt, type KGF GB 1500 BOREMA personal protection system, type APSS iBOR 22 Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), Angel Victory 1350/220 Tech Closing 220 tons year 2004 Clamping plan WxH 860x830 Pgedpfx Adjpdrpzjisw Scrow 55mm 618 cm3 Cc 200 Minimum mold height 250mm Maximum 730mm

Year of construction: 2017, condition: ready for operation (used), Laser power: 10kW (10000W), working range: 3000mm/1500mm, max. material thickness: mild steel: 25mm, stainless steel: 30mm, aluminum: 30mm, copper: 12mm, brass: 15mm. Positioning speed: 120m/min, positioning accuracy: +/-0.05mm, max. workpiece weight: 1100kg. Machine dimensions X/Y/Z: approx. 9500mm/3500mm/3500mm, suction dimensions X/Y/Z: approx. 1500mm/1500mm/4000mm, machine weight: approx. 12000kg, operating hours: approx. 17000h. Documentation available. On-site inspection is possible. Expected to be available from June 2025. Podpfxsvyiqge Adisgw

Condition: good (used), Shrink tunnel from a German manufacturer: -Tunnel opening approximately 500 x 200 mm. -Temperature adjustable up to 250 degrees and transport speed up to 25 m / min. Pjdpfxjh U A I Ro Adijgw -Choice of fixed or co-rotating tunnel bars. -By means of deflectors, the hot air streams at the top and in the middle can be adjusted separately. -Bottom air can be switched on separately. -The machine can be pushed or fixed in place by means of lockable castors.

Condition: used, Year of construction: 2009, operating hours: 20,536 h, pressing force: 80 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, empty load weight: 16,000 kg, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 20,536 hours, as of September 2024 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Psdeu Thypopfx Adisgw Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine is currently in our workshop undergoing partial refurbishment. We expect the refurbishment work on the machine to be completed by the end of October, after which the machine will be tested and released for sale.

Year of construction: 2010, condition: ready for operation (used), A CNC turret punching machine Amada and an automatic loading and unloading unit LKI Käldman (Amada) are available. 1) CNC turret punching machine Amada EMZ3610, year of manufacture: 2010, pressing force: 300kN, travel X/Y: 2500mm/1525mm, travel X/Y with repositioning: 5000mm/1525mm, max. material thickness: 4.5mm, max. table load: 160kg. Traversing speed X/Y: 100m/80m/min, axis speed: 128m/min, positioning accuracy: +/-0.1mm. Turret stations 45, auto-index stations: 2xB/2xC, turret speed: 30rpm, stroke rate: 1000 strokes/min, machine weight: approx. 21000kg. 2) Loading and unloading system LKI Käldman (Amada) MP Sheetcat 3015, year of manufacture: 2017, min. sheet dimensions X/Y: 1000mm/300mm, max. sheet dimensions X/Y: 3050mm/1525mm, sheet thickness: 0.8mm-6mm, max. sheet weight per pallet: 3000kg, suction cups: 34, machine dimensions X/Y/Z: approx. 8400mm/3600mm/3100mm. Documentation available. On-site inspection is possible. Pgedpov Rp Tcjfx Adisw

Condition: used, Year of construction: 1998, Overview This machine was built in 1998 by French manufacturer Sidel. The machine is in very good working condition, is already professionally dismantled and stored in a warehouse. Techn. Details Capacity: 7.200 bph in 1,5L Number of moulds:  6 (molds not included) Equipped with quick change for shell molds Number of heating modules: 10 modules Neck personalization: 29/25      Working hours: 47.000 only         Machine was regularily maintained       Machine equipped with:            Sidel preforms elevator to unscrambler Sidel preforms unscrambler & feeder Sidel oven & blowing wheel for 6 molds Sidel electrical cabinet Sidel PCC drive & control panel Big set of spare parts list upon request Pjdpforkgy Uex Adiegw

Condition: good (used), Year of construction: 2013, functionality: fully functional, Machine is still in production. It can be inspected in Greece. It is ready to be used. Pgodpfx Aev A I E Isdiow

Condition: used, functionality: fully functional, Foundry factory for sale, Property includes 15 buildings, 6 hectares of land. Located at the Karhula industrial site next to the city of Kotka in southeastern Finland, Karhulan Valimo was founded in the 1880’s. In 1902, the foundry was merged with a wood grindery, glass factory, brick factory and engineering works to form the Karhula Oy. In 1915 the Karhula Factories were sold to Ahlström Corporation. The current Foundry was built in 1960 and in 2000 Ahlström sold the foundry to Sulzer Pumps Finland. In 2016 Sulzer Pumps decided to close the foundry and it was sold to Karhulan Foundry Oy, which was unfortunately declared bankrupt in March 2021. Throughout its history, the foundry has been known of been able to produce highly demanding castings particularly in high alloyed steels. In 2022 Karhu Assets Oy bought the facilities and machinery of the foundry. Most of the equipment in the fettling shop has already been sold, while most of the machinery in the moulding department and meltshop are intact and available. All heat treatment furnaces, a total of 10 units, are in place and available for sale. Welcome to visit on the site! The equipment is located in Kotka, 48600, Finland, and is sold EXW Kotka in its current condition. The flight time from most European cities to Helsinki, Finland, is approximately 2 hours, and the drive from Helsinki to Kotka via the motorway is about 120 km (1 hour). You are welcome to visit us in person to inspect the foundry machinery! Pgodpfx Adjuxmt Tsiew Second-Hand Condition: All machines, equipment, and articles are sold in a used condition. No Warranty, Exchange, or Guarantee: The seller does not offer any warranties or guarantees on the items sold. There is no option for exchange or refund, so the buyer accepts any risks associated with the purchase. As Inspected On Site: The buyer must inspect the goods on-site before making the purchase, as the sale is final once inspected. The seller will not be held responsible for any defects found after the purchase.