CNC turning and milling center

EMCO MT 65 G2

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included) Ppodpfx Adewp Rqfeler

Condition: used, Year of construction: 2004, functionality: fully functional, machine/vehicle number: 8038938456C, turning length: 450 mm, turning diameter over cross slide: 505 mm, turning diameter: 202 mm, spindle motor power: 10,000 W, spindle speed (max.): 6,000 rpm, spindle bore: 51 mm, Gildemeister CTX 310 Heidenhain Turn+ Ppedewk E Uzjpfx Adljr The machine its full functional, but have some miner isue.

Condition: good (used), Year of construction: 2000, table width: 1,000 mm, table length: 1,800 mm, ram plate width: 600 mm, total length: 25,000 mm, total width: 27,000 mm, total height: 47,000 mm, overall weight: 43,000 kg, die cushion stroke: 200 mm, Siemens Simatic OP 27 control system Light barrier Sick Separate control cabinet Ritta Side passages Ppedpfx Ajtiwgisdlsr Ground level installation

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, We offer you the following: Manufacturer: DMG Mori Model: CMX 50 U Year of manufacture: 2019 Control unit: Slimline Siemens Operate Travel distances: X-axis: 500 mm Y-axis: 450 mm Z-axis: 400 mm B-axis: -5 to +110 ° C-axis: 360 ° Main spindle: Tool holder: SK 40 Spindle speed range: 20 - 12,000 rpm Main spindle drive power (100/40%): 13 / 9 kW Pedeywlkcopfx Adlopr Working table: Table size: D 630 x 500 mm Tool changer: Number of tool pockets: 30 positions Rapid traverse rates: Rapid traverse (X/Y/Z): 30 m/min Operating hours: approx. 7,070 h Spindle hours: approx. 2,800 h Technical features & accessories: - Direct linear measuring system in x, y, and z axes, including air purge - Air blow switching via M function - Production package, consisting of: - Internal coolant supply 12 bar - Chip conveyor, 250 l tank - Bed flushing via M function - Coolant spray gun - Machine enclosure roof - 4-color signal lamp - Renishaw measuring kit, consisting of: - Touch probe PP40 - Tool measurement TS27R - Tool breakage monitoring - Calibration tool - Preparation for 3DquickSET Accessories, tools, and clamping devices shown are only included in the scope of delivery if specified in the additional information. Technical data and specifications are subject to change and errors. Prior sale reserved!

Condition: used, functionality: fully functional, Year of construction: 2021, operating hours: 116 h, load capacity: 4,000 kg, lifting height: 17,000 mm, fuel type: diesel, mast type: telescopic, power: 85 kW (115.57 HP), empty load weight: 13,040 kg, drive type: Diesel, Rigid telescopic forklift Ppedjv Ezt Depfx Adler Mast type: Telescopic Speed class: 20 Technical condition: New Front tires type: Air Front tires Size: 400/70-24 Front tires Condition: 80 - 100% Rear tires Type: Air Rear tires Size: 400/70-24 Rear tires Condition: 80 - 100% 3rd valve, 4th valve, heating, full cabin, CE certificate, Specifications: -Carrying capacity 4000kg -Lifting height 16,4m -MAX gradeability 40% -Curb weight 13040kg -Engine KUBOTA 85,1kw ( 114hp ) -Capacity 3769cm3 -Emission standard Tier4f -Steering Front wheel steering, all wheel steering and crab steering.

Condition: reconditioned (used), functionality: fully functional, approx. 4.5 m long infeed and centering table Drive via chain from the feed motor Centers the logs in the middle of the rotor Debarking machine VK 26 Podpfou Hmacex Adlopr 4 main cutters 4 pre-cutters 30 KW main motor 11 KW feed unit non-driven extraction table Machine workshop checked Machine cleaned and repainted

Condition: used, Year of construction: 2007, working width 1380 mm Psdet Hw Iijpfx Adlspr workpiece height 70 mm total power requirement 45 kW weight of the machine ca. 5.500 kg

Condition: ready for operation (used), Year of construction: 2009, functionality: fully functional, CNC Turning and Milling Center - DMG GILDEMEISTER - CTX gamma 1250 TC YOM: 2009, until 2011 showroom machine, from 2012 operating Ppsdpfxew Hg Nls Adlsr The machine can be inspected by appointment in the factory under power. Condition: Good (high accuracy), ready for immediate use. Spindle hours (August 1st, 2025): 9.580 h The heart of the machine is the integrated traveling column with turning milling spindle and interpolating B-axis. Machine basic data: * Part hollow clamping device (hydraulic) * C-axis * Cross slide above with turning/milling spindle as motor spindle, with hydraulic clamping in turning, tool holder: Capto C6 * Y-axis: +/- 200 mm * B-axis: +/- 120° * Disc-type tool magazine * Absolute, direct measuring systems in X-, Y-, Z1-axis * USB-interface, Ethernet interface TECHNICAL SPECIFICATIONS: * Control: Heidenhain CNC Pilot 4290, 3-D path control TURN PLUS Working area: * Swing diameter over bed: 630 mm * Turning diameter: 630 mm * Spindle distance: 1.510 mm * Bar diameter max.: 65 mm Main drive I: * Drive power (100% / 40% ED): 24 / 34 kW * Speed range from - up to: - 5.000 rpm * Speed of the C-axis: - 5.000 rpm Turning/milling spindle: * Tool holder: Capto C6 * Spindle speed: - 12.000 rpm * Drive power (100% / 40% ED): 13.2 / 22 kW * Torque (100% / 40% ED): 60 / 100 Nm Tool magazine: * Number of tools: 36 * Dimensions of the machine approx. (Width/Depth/Height): 6.860 x 4.220 x 2.530 mm * Total weight of the machine approx.: 18,5 tons EQUIPMENT: * Well equipped … * No steady rest available * Documentation complete available. Detailed technical data sheet and information on equipment available on request. There is no guarantee for correctness and completeness of the technical details and and accessories.

Condition: excellent (used), CPM 2000 granulator, 90kW engine die diameter 410mm We have several pieces Psdpfx Ajwcdpnjdlspr

Condition: as good as new (ex-display), Various designs such as round, hexagonal or square and in smooth smooth version, cross-grooved version or with longitudinal and transverse grooves. A current list of available new and as-new SK32/SK42/SK52/SK65/SK80/SK100 expansion chucks can be found on our homepage. Pedpfsh Dmamsx Adlepr We look forward to your inquiry. STALEX Machine Tools GmbH