Used Cone for sale (1,003)

Condition: good (used), Chuck flange, flange mount, chuck flange, drive flange, intermediate flange, chuck faceplate -Muck flange: for three-jaw chucks, four-jaw chucks, faceplates Ndedpfx Ahsxrk T Ne Sec -Outer diameter: Ø 200 mm -Bolt circle: Ø134 mm -Socket: Short cone 6, cone Ø 101 - 106 mm -Overall dimensions: Ø 200 x 145 mm -Weight: 7.6 kg

Condition: good (used), live center, live center, live morse taper, live center, live lathe center, live center, centering cone, centering ball, centering mandrel, centering chuck, pipe centering chuck, live centering chuck -Manufacturer: Kondamat, centering chuck pipe centering chuck -Recording: MK4 Nodpfxexrlvle Ah Sedc -Dimensions: see photos -Dimensions: Ø 78 x 230 mm -Weight: 2.7 kg

Condition: used, Year of construction: 2011, Used Equipment Ndsdpfx Aszvz Tbjh Soc Year of Manufacture: 2011 Condition: Currently installed Equipment and Technical Data: -Filter housing base ring NFHSU 9/9 with discharge chute for press - Discharge: 1.1 kW - Storage volume in the base ring approx.: 3.25 m³ - Dimensions L x W x H (incl. base ring) 2440 x 2440 x 900 mm - Ground clearance: 350 mm - Conveyor screw for briquetting press 0.75 kW - Extension and expansion rings are optional; max. storage volume approx. 12 m³ - Extension and injection ring NFHSU for 9/9 and 10/10 Jet, L x W x H: 2480 x 2480 x 500 mm - Expansion ring for NFHSU 9/9, 2480x2480x700 mm, with inspection door and type-tested explosion flap - Filter for filter housing NFHSU 9/9/20, filter area 116 m²: The Nestro filter system NFHSU is a solid filter construction made of 4 mm galvanized steel sheet and is designed for outdoor installation and weather resistance. This filter system is particularly robust and designed for underpressure operation up to -3,500 Pa. The filter system is equipped with upper and lower inspection doors 600 x 600 mm, with automatic filter regeneration, dry extinguishing system, differential pressure switch / volumetric flow monitoring and the necessary explosion protection. Note: Filter is equipped with high-quality filter material, BIA category M, antistatic, residual dust content < 0.1 mg/m³ and suitable for return air operation. Further technical data: - Filter tube length: 2,000 mm - Filter tube diameter: 230 mm - Number of filter tubes: 81 - Filter area: 116.0 m² - Filter regeneration: automatic/motorized - Number of vibrating motors: 4 pcs - Fan shroud for NFHSU 9/9 including inspection door - Fan US-FHN (clean gas) 22 kW 16,400 m³/h - 3,200 Pa: A Nestro high-performance fan with above-average efficiency and high energy saving potential when using a frequency inverter (optional). The robust welded construction is primed and painted in RAL 5015. The fan is delivered as standard with an inlet cone and backflow damper. Technical data at a glance: - Volumetric flow: 16,400 m³/h - Corresponding underpressure: 3,200 Pa - Electric motor: 22 kW / 400 Volt / 50 Hz - Speed: 3,000 rpm - Design: B5 - Pressure nozzle: without - Application area: Nestro underpressure filter and others - Injection nozzle d= 400 mm with flange ring - Injection nozzle d= 350 mm with flange ring - Backflow damper d= 350 mm with flange edge - Backflow damper d= 400 mm with flange edge - Briquetting press C150; 30 - 50 kg/h, hydraulic unit 5.5: Technical data: - Power consumption (hydraulics): 5.5 kW - Briquette diameter: 50 mm - Weight: 650 kg - Briquetting performance with a bulk density of approx. 250 kg/m³, material-dependent: 30 - 50 kg/h - Ground clearance with base frame (art. no. 710300): 350 mm - Briquetting press, dust-proof - Briquetting press complete with hydraulic solenoid valve control for automatic operation, oil tank with 100 l oil, in welded construction, including main cylinder, stuffing cylinder, gripper cylinder, pressing jaw, electrical control panel with fully automatic control and 5 m cable The press is standardly equipped with: Monitoring switch for oil temperature, hardened press bushing, connection part for briquette line and automatic briquette length adjustment

Condition: used, Year of construction: 2017, Overview Pilot-scale tunnel for the continuous thermal treatment of packaged products by water spray. The unit heats or cools filled containers – PET and glass bottles, jars, cans – as they travel through the tunnel on a modular conveyor belt. Heating and cooling run as separate cycles, one process per pass. Temperature is regulated by a PT-100 probe and a controller acting on a direct steam injection valve, which keeps operation simple and the set point stable. Frame, tanks and main components are built entirely in AISI 304 stainless steel. The machine was used exclusively in a pilot plant for R&D trials and never ran in full-scale industrial production. It is in excellent condition, well maintained, and already dismantled and stored. Technical details - Year of manufacture: 2017 - Treatment zone: 500 mm wide x 2,700 mm long - Conveyor belt: 500 mm wide perforated modular polypropylene mesh - Belt speed: adjustable via mechanical variator - Retention time: adjustable from 5 to 20 minutes - Throughput: approx. 500 units/h, adjustable - Overall dimensions: approx. 2,870 x 1,000 x 2,250 mm (L x W x H) Nedszxnu Dopfx Ah Sodc - Material: AISI 304 stainless steel - Electrical supply: 3 x 400 V + N + PE, 50 Hz - Total installed power: 1.7 kW (recirculation pump 1.5 kW, conveyor drive 0.18 kW) - Steam connection: DN 15 at 7.5 bar - Water connection: 1" at 3 bar - Compressed air connection: 1/4" at 6 bar - Vapour extraction: two Ø 154 mm chimney outlets Equipment - Spray tunnel with 12 stainless steel full-cone nozzles - Lower collection tray and tank with float level valve and overflow pipe - Stainless steel centrifugal recirculation pump - Automatic temperature control via PT-100 probe and direct steam injection valve - Vapour capture hoods at infeed and outfeed - Tank manhole, 185 x 235 mm - Base frame to set the machine to line working height Condition and availability - Used only for R&D trials in a pilot plant, never in industrial production - Excellent condition, well maintained - Already dismantled and stored - Can be inspected on site; loading by the seller possible - Immediately available - Location: Spain

Condition: excellent (used), functionality: fully functional, travel distance X-axis: 1,000 mm, travel distance Y-axis: 700 mm, spindle speed (max.): 2,000 rpm, table length: 1,100 mm, table width: 842 mm, X axis: mm 1.000 Y axis: mm 700 Spindle travel: mm 300 Table dimensions: mm 1.100 x 842 Spindle speed: rpm 40 – 2.000 Spindle cone: MT 4 Max power: kW 10 Max loading on table: ton 1 Machine weight: ton 15 EQUIPPED WITH A LOT OF ACCESSORIES Ndedpfozizgbox Ah Ssc

Condition: used, mileage: 47,830 km, power: 206 kW (280.08 HP), first registration: 08/2003, fuel type: diesel, overall weight: 14,500 kg, axle configuration: 2 axles, brakes: retarder, color: red, gearing type: automatic, emission class: euro3, total length: 10,000 mm, total width: 2,350 mm, total height: 3,300 mm, Year of construction: 2003, Equipment: ABS, air conditioning, compressor, MAN LE 14.280 with METZ DLK 23-12 PLC 3.2 L32 aerial ladder, in immediately operational condition. ---- First registration: 05.08.2003 Mileage: 47,826 km Operating hours of the ladder superstructure: 1,608 hours Operating hours of the vehicle: 2,150 hours Equipment of the base vehicle: * Suspension type: leaf spring/leaf spring * Wheelbase: 4500 mm * Permissible gross vehicle weight: 14.5 t * Automatic transmission ZF 5 HP 590 with retarder * Fuel tank: 125 l, right side * Adjustable steering wheel * Axle ratio i = 5.86 * Differential lock in rear axle * Medium-length cab * Driver's comfort seat with lumbar support - manufacturer: GRAMMER * Passenger seat bench - manufacturer: GRAMMER * Air conditioning R134A * Exhaust pipe with tailpipe on the left * Auxiliary starter system * Anti-lock braking system (ABS) * Traction control system * Disc brake for front axle * Armrests on both doors * Additional long-range and fog lights * Hour meter * Cruise control * Stabilizers for front and rear axles * Headrests for driver and passenger * Cab rear wall with 3 windows * Heated and electrically adjustable exterior mirrors * Wide-angle mirror on the right, heated * Curb mirror on the right, heated and electrically adjustable * Electric windows on the left and right * 4-wheel parking brake (also on the front axle) * Tire chains on the rear axle * Winter tires 10R22.5 Equipment of the aerial ladder superstructure: * Superstructure: Metz aerial ladder DLK 23-12 PLCIII with rescue platform (rescue height approx. 30.75m). Max. outreach angle: 75 degrees, max. platform load capacity: 270 kg, nominal rescue height: 23 m, nominal outreach: 12 m, outriggers: horizontal-vertical, variable outrigger width between 2,400 mm and 4,500 mm * Rotating beacon lights at the front and rear * Front and rear flashing lights * Air horn * Stretcher storage for accommodating a DIN stretcher, including conversion for accommodating a rescue basket stretcher, load capacity up to 150 kg * Permanently installed 230V power supply to the rescue platform, 2 Schuko sockets in the rescue platform * Permanently installed water supply line in the upper part of the ladder with shut-off valve and B-Storz couplings * 3 anchor points in the rescue platform for securing the crew * Load eye on the lower ladder, loadable up to 4,000 kg * Load eye on the basket segment (between ladder tip and rescue platform) for attaching a lowering device, 270 kg/400 kg payload * LED ambient lighting on the undercarriage * XXL platform on the turntable for accommodating a DIN generator, ventilation unit, traffic cones, etc. * 2 adjustable spotlights at the end of the lower ladder, operable from the main control panel * 2 spotlights on the basket * Permanently installed battery charger Waeco PerfectCharge IU154A * Complete service booklet available, all maintenance performed annually Upon request and for an additional charge, a new 20-year inspection can be carried out, including hose replacement and inspection! ----Immediately operational vehicle in well-maintained condition, both inside and out! Non-smoking vehicle! Your contact person for this vehicle: ---- Daniel Seidler Tel: Mobile: also WhatsApp Email: Ndedezw R Sijpfx Ah Sec Subject to changes, prior sale and errors!

Condition: used, Year of construction: 1982, test force 588,613,980,147 N checking height 250 mm throat 150 mm weight of the machine ca. 100 kg dimensions of the machine ca. 460 x 210 x 840 mm ype of force: Spring force load Ndodsyan Nrjpfx Ah Ssc Preload: 98 kN Stroke: 150 mm Test height: 250 mm Test force: 588 N, 613 N, 980 N, 1471 N, 2450 N Voltage: 220 V Current type: 50 Hz Accessories and special equipment: - Holder with diamond cone 120 degrees - Hardness comparison plate HRC - Holder with carbide ball 2.5 mm diameter - Hardness comparison plate HR 2.5/187.5 - Test table 190 mm diameter - Prismatic test table for max. 85 mm diameter - Protective cover - Machine table with drawer Space requirement: 460 x 210 x 840 mm Weight: approx. 100 kg

Condition: new, neu ca. 10 Wochen ab Auftrags Türkei 52700 € 996.03 € 2550 mm 10 mm 10 mm 8 mm 8 mm 6 mm 245 mm 245 mm 180 mm 1,5 / 6 m/min 7.5 kW 4800 mm 1600 mm 1470 mm 6170 kg 4 rolls Top rolll driven by hydromotor and planetary gearbox, bottom roll driven by gear and cardan system Pinch roll and latereal rolls move with hydraulic cylinders Digital read-out for lower and side rolls position Njdpfx Ahjyb Syko Ssdc Hardened rolls Conical bending device Hydraulic load relieving of upper roll Hydraulic drop-end bearing 2 working speeds Protectionagainst overload Moveable control pane According to CE rules OPTIONAL EQUIPMENT: Infinitely adustable speed of rolls Hydraulic side support Hydraulic top support NC control IMPORTANT ISSUES AT CONICAL BENDING: The max. sheet metal thickness isequivalent to 50 % of nominal capacity The cone length can be max. 30 % oremust be more than 60 % of roll length Hardened rolls are recommended

Condition: good (used), Faceplate, faceplate chuck, four-jaw chuck, face turning chuck -Faceplate: Chuck size Ø 560 mm -Bolt circle: Ø 170 mm Njdjx R R R Ijpfx Ah Sjdc -Through hole: Ø 90 mm -Reference: Short cone 8 (Ø 136-139 mm) -Dimensions: Ø 560 x 200 mm -Weight: 77.3 kg

Condition: new, neu ca. 10 Wochen ab Auftrags Türkei 32480 € 620.37 € 1550 mm 9 mm 9 mm 7 mm 7 mm 5 mm 180 mm 180 mm 150 mm 1,5 / 6 m/min 5.5 kW 3900 mm 1150 mm 1250 mm Njdpsynmzpjfx Ah Sodc 3250 kg 4 rolls fullhydraulic drive of upper roll and lower roll hydraulic infeed of lower and side roll digital read-out of lower and side rolls position hardened rolls conical bending device hydraulic load relieving of upper roll hydraulic drop-end bearing 2 working speeds central lubrication system protectionagainst overload moveable control pane according to CE rules OPTIONAL EQUIPMENT (PRICES ON REQUEST): infinitely adustable speed of rolls hydraulic side support hydraulic top support NC control IMPORTANT ISSUES AT CONICAL BENDING: the max. sheet metal thickness isequivalent to 50 % of nominal capacity the cone length can be max. 30 % oremust be more than 60 % of roll length hardened rolls are recommended

Condition: new, neu ca. 10 Wochen ab Auftrags Türkei 53700 € 1014.93 € 2050 mm 16 mm 16 mm 13 mm 13 mm 10 mm 260 mm 260 mm 200 mm 1,5 / 6 m/min 7.5 kW 4300 mm 1600 mm 1550 mm 6100 kg 4 rolls Top rolll driven by hydromotor and planetary gearbox, bottom roll driven by gear and cardan system Pinch roll and latereal rolls move with hydraulic cylinders Digital read-out for lower and side rolls position Hardened rolls Conical bending device Hydraulic load relieving of upper roll Hydraulic drop-end bearing 2 working speeds Protectionagainst overload Moveable control pane According to CE rules Njdpfx Aheynm Ehe Sjdc OPTIONAL EQUIPMENT: Infinitely adustable speed of rolls Hydraulic side support Hydraulic top support NC control IMPORTANT ISSUES AT CONICAL BENDING: The max. sheet metal thickness isequivalent to 50 % of nominal capacity The cone length can be max. 30 % oremust be more than 60 % of roll length Hardened rolls are recommended

Condition: new, neu ca. 12 Wochen ab Auftrags Türkei 97400 € 1840.86 € 2050 mm 30 mm 30 mm 25 mm 25 mm 20 mm 350 mm 350 mm 260 mm 1,5-5 m/min 22 kW 5000 mm 2000 mm 1900 mm 11000 kg 4 rolls fullhydraulic drive of upper roll and lower roll hydraulic infeed of lower and side roll digital read-out of lower and side rolls position hardened rolls conical bending device hydraulic load relieving of upper roll hydraulic drop-end bearing 2 working speeds central lubrication system protectionagainst overload Ndedpfx Aoynm Enoh Ssc moveable control pane according to CE rules OPTIONAL EQUIPMENT: infinitely adustable speed of rolls hydraulic side support hydraulic top support NC control IMPORTANT ISSUES AT CONICAL BENDING: the max. sheet metal thickness isequivalent to 50 % of nominal capacity the cone length can be max. 30 % oremust be more than 60 % of roll length hardened rolls are recommended

Condition: new, Our SAPI "Mammut" pressure blasting unit with a 60-liter tank capacity is suitable for all common blasting media. The blasting pressure can be continuously adjusted from 0.1 to 12 bar using the permanently installed pressure regulator. A water separator is also permanently installed on the blasting unit; this separates moisture from the compressed air and prevents the blasting media from clumping due to excessive moisture. Our safety shut-off device is included for safe operation of the sandblaster. This starts and stops the blasting process by operating the hand lever mounted on the blasting hose. Included in delivery: SAPI pressure blasting unit "Mammut 60 L" 1" pressure regulator, permanently mounted 1" water separator, permanently mounted SAPI safety shut-off Technical specifications for the pressure blasting unit: Precisely adjustable from 0.1 - 12 bar TÜV-tested with certificate 1" fixed piping, internal and external Rubber-coated metal cone with rubber seal Generous hand hole Rubber-coated metal cone with rubber seal Large hand hole Rubber-wheeled chassis Abrasive dosing valve (suitable for all common blasting media) Ndsdpswc Afhjfx Ah Ssc Capacity 60 l Total height 1,130 mm Bowl diameter 360 mm Total diameter 700 mm Weight approx. 60 kg ADVANTAGES OF THE SAPI PRESSURE BLASTING UNIT with safety shut-off Fast shut-off and start-up times, while complying with the regulations of the professional associations (VBG 48) Pressure setting Can be precisely adjusted before the actual blasting process, continuously adjustable from 0.1 to 12.0 bar. Reduced abrasive consumption, as the pressure vessel remains permanently pressurized, thus eliminating unnecessary abrasive run-on. Upon restart, the full blasting pressure is immediately available at the nozzle and does not need to be slowly built up. This significantly reduces abrasive consumption and significantly reduces wear on the blasting hose. No moisture (condensate) builds up in the vessel, as the vessel remains constantly pressurized and is not vented and vented with every start and stop. This process also offers other advantages, such as: Optimal abrasive dosing with a hardened fine dosing valve Lower compressed air consumption, thus significantly reducing fuel consumption (diesel) One-person operation, as the blasting pressure is constantly displayed by the vessel pressure and can be easily adjusted on the pressure gauge without prior start-up. No failure-prone components such as control valves, diaphragms, or seals, making it easy to maintain and reliable. Only the blasting hose needs to be checked in the safety shutoff and replaced if necessary.

Condition: new, Year of construction: 2025, Our SAPI "Mammut" pressure blaster with a 100-liter tank capacity is suitable for all common blasting media. The blasting pressure can be continuously adjusted from 0.1 to 12 bar using the built-in pressure regulator. A water separator is also permanently installed on the blaster, which separates moisture from the compressed air and prevents the blasting media from clumping due to excessive moisture. Our safety shut-off system ensures safe operation of the sandblaster. This starts and stops the blasting process by operating the hand lever mounted on the blasting hose. The pressure blaster is delivered fully operational, assembled in a space-saving mesh box. All that's required is to connect the compressed air supply and fill it with blasting media. It can be easily transported by forklift or pallet truck. A lockable aluminum box is installed for storage of protective clothing, spare parts, etc. The scope of delivery includes: SAPI "Mammut 100 L" pressure blaster 1" pressure regulator, permanently mounted 1" water separator, permanently mounted SAPI safety shut-off device Abrasive sieve Cover 10 m blast hose, fully assembled, ø 25x7 mm Silicon carbide Venturi long nozzle, diameter optionally 6 mm, 8 mm, or 10 mm RED 2 sandblasting helmet Nylon/cotton sandblasting overalls 1 pair of leather blasting gloves 10 m breathing air hose, fully assembled SAF breathing air filter/activated carbon filter Wearing parts set consisting of: 100 tear-off films for RED 2 10 inner discs for RED 2 1 blast hose coupling, 25x7 mm nylon 2 rubber seals for blast hose coupling 1 nozzle holder, 25x7 mm Grid box with blast hose holder Aluminum box Lockable Technical specifications of the pressure blaster: Precisely adjustable from 0.1 - 12 bar TÜV-certified with certificate Fixed 1" internal and external piping Rubber-coated metal cone with rubber seal Large hand hole Rubber-wheeled chassis Abrasive dosing valve (suitable for all common blasting media) Ndjdpswc Ri Isfx Ah Ssc Capacity: 100 l Total height: 1,130 mm Bowl diameter: 490 mm Total diameter: 900 mm Weight: approx. 75 kg Dimensions of the mesh box: Length: 1,460 mm Width: 840 mm Height: 1,400 mm Total weight including all accessories: 260 kg

Condition: new, Year of construction: 2025, Our SAPI "Mammut" pressure blasting unit with a 200-liter tank capacity is suitable for all common blasting media. The blasting pressure can be continuously adjusted from 0.1 to 12 bar using the permanently installed pressure regulator. A water separator is also permanently installed on the blasting unit; this separates moisture from the compressed air and prevents the blasting media from clumping due to excessive moisture. Our safety shut-off device is included for safe operation of the sandblaster. This starts and stops the blasting process by operating the hand lever mounted on the blasting hose. Njdpfx Ajwc Rk Ejh Sjdc Included in delivery: SAPI pressure blasting unit "Mammut 200 L" 1 1/4" pressure regulator, permanently mounted 1 1/4" water separator, permanently mounted SAPI safety shut-off Technical specifications of the pressure blasting unit: Precisely adjustable from 0.1 - 12 bar TÜV-tested with certificate 1 1/4" fixed piping inside and outside Rubber-coated metal cone with rubber seal Generous hand hole Rubber-coated metal cone with rubber seal Large hand hole Rubber-wheeled chassis Abrasive dosing valve (suitable for all common blasting media) Capacity: 200 l Total height: 1,420 mm Vessel diameter: 600 mm Total diameter: 1,000 mm Weight: approx. 140 kg ADVANTAGES OF THE SAPI PRESSURE BLASTING UNIT with safety shut-off Fastest start-up and shutdown times while maintaining compliance the regulations of the professional associations (VBG 48) The pressure setting can be precisely adjusted before blasting – continuously adjustable from 0.1 to 12.0 bar Lower abrasive consumption, as the pressure vessel remains permanently pressurized and there is no unnecessary run-on time Upon restart, full blasting pressure is immediately available at the nozzle – no pressure build-up necessary → lower consumption & less wear on the hose No condensate formation in the vessel, as it remains constantly pressurized → no venting or venting with every start/stop Optimal abrasive dosing with a hardened fine dosing valve Less compressed air required → noticeably lower diesel consumption One-person operation, as the pressure can be displayed and adjusted directly on the pressure gauge – even without starting No failure-prone components such as control valves, diaphragms, or seals → easy to maintain and reliable Only the blasting hose in the safety shut-off device needs to be checked and replaced if necessary

Condition: excellent (used), Year of construction: 2016, operating hours: 200 h, functionality: fully functional, total height: 1,760 mm, total length: 1,100 mm, total width: 850 mm, workpiece weight (max.): 12 kg, spindle speed (max.): 10,000 rpm, spindle speed (min.): 500 rpm, feed length X-axis: 100 mm, feed length Y-axis: 190 mm, feed length Z-axis: 325 mm, type of input current: three-phase, grinding wheel diameter: 125 mm, overall weight: 520 kg, grinding length: 270 mm, rotational speed (min.): 500 rpm, rotational speed (max.): 10,000 rpm, center height in crank: 220 mm, center height: 300 mm, collet bore: 25 mm, grinding spindle speed: 10,000 rpm, feed rate X-axis: 1 m/min, feed rate Y-axis: 1 m/min, feed rate Z-axis: 1 m/min, pivoting range: 360 °, travel distance X-axis: 100 mm, travel distance Y-axis: 190 mm, travel distance Z-axis: 325 mm, center width: 620 mm, grinding spindle motor power: 1,100 W, table length: 190 mm, table width: 200 mm, table height: 1,020 mm, power: 1.1 kW (1.50 HP), height adjustment type: electric, workpiece diameter (max.): 400 mm, input current: 20 A, grinding diameter: 300 mm, input frequency: 50 Hz, disc diameter: 125 mm, input voltage: 280 V, space requirement width: 2,000 mm, space requirement length: 1,800 mm, space requirement height: 1,800 mm, grinding wheel speed: 10,000 rpm, year of last overhaul: 2022, distance table to spindle center: 325 mm, tool diameter: 300 mm, workpiece length between centers: 270 mm, distance between centers: 270 mm, number of spindles: 1, Equipment: rotational speed infinitely variable, max. grinding diameter 238 - 620 mm grinding length 190 mm workpiece length 380 - 940 mm spindle turning speed - stepless 2 - 12000 U/min current capacity 380 kVA power capacity - grinding motor 1,1 kW total power requirement 2,2 kW weight of the machine ca. 0,6 t !!! We have almost all spare parts for the Deckel S 11 machines in stock !!! !!! Accessories can be varied as desired !!! We would be happy to trade in your used Deckel S 11 - contact us! 2016 S25 003004 V, 50/60 Hz, with CEE plug and cable Color: light gray Nedpew U Ehbefx Ah Sjdc motorized height adjustment, axial grinding spindle adjustment Equipment: * Opto-electronic measuring device with measuring electronics Image processing, PC (Original ISOG) * CCD camera and monitor * Dividing head Sk 40 with dividing disk 24 R * 1 dividing disk each 14, 16, 18 * Tightening screw M 16 * Counter bearing complete with 4 center punch points * Center point Sk 40 with driver * Twist-u. Relief grinding device with rack housing * Dust extraction completely without vacuum cleaner * LED machine light * Tooth support complete with support and sliding blades * Setting gauge * Universal setting gauge * Handwheel facility * Dressing device with 3 diamonds * 1 set of collets 1.0 - 17.5 mm by 0.5 mm rising * Pliers sleeve and extraction nut and key * 10 pieces of direct collets Sk 40 6 - 25 mm * 4 cone reducing sleeves Sk 40 x Mk 1, 2, 3, 4 * Clamping nut * 12 grinding wheel chucks * Tool cabinet with shelves * 2 protective hoods * various diamond / borazon discs * Operating instructions and key, spare parts list, circuit diagram * Set of technical grinding instructions ##### Machine is partially overhauled and has an electrical acceptance report!#####

Condition: good (used), Grinding wheel holder, standard flanges, special flanges, grinding wheel flange Nodpfx Asw Dnx Njh Sjdc -Grinding wheel holder: with grinding stone -Mounting: Hole shaft cone Ø47-55 mm, thread M60 see photos -Grindstone: 400 x 40 mm, unfortunately without type designation -Transport dimensions: Ø 400 x 85 mm -Weight: 31.1 kg

Condition: good (used), Grinding wheel holder, standard flanges, special flanges, grinding wheel flange -Grinding wheel holder: with grinding stone -Mounting: Hole shaft cone Ø 62-69 mm / Left thread. -Grinding wheel: Ø 450 x 40 mm Nsdew Dn Sijpfx Ah Ssdc -Transport dimensions: Ø 450 x 140 mm -Total weight: 30 kg

Condition: good (used), Grinding wheel holder, standard flanges, special flanges, grinding wheel flange -Grinding wheel holder: with grinding stone -Mounting: Hole shaft cone Ø 32-35 mm -Grinding wheel: Ø 210 x 40 mm -Transport dimensions: Ø 210 x 70 mm -Total weight: 4.3 kg Ndodpow Dpfqsfx Ah Soc

Condition: good (used), Chuck flange, flange holder, lathe chuck flange, driving flange, intermediate flange, lathe chuck face plate, mounting flange Nsdpfx Asxdhu Ioh Sedc -Chuck flange for: driving heart, three-jaw chuck, four-jaw chuck, face plate -Outside: Ø 260 mm -Adapter: short cone size 6 (Ø103-105 mm) -Bolt circle: Ø 133 mm -Dimensions: Ø 260 x 140 mm -Weight: 11.2 kg

Condition: good (used), Chuck flange, flange holder, lathe chuck flange, driving flange, intermediate flange, lathe chuck face plate, mounting flange -Chuck flange for: driving heart, three-jaw chuck, four-jaw chuck, face plate Nsdpfx Ahexdhvlj Sodc -Outside: Ø 225 mm -Mounting: cone Ø100-102 mm -Bolt circle: Ø 140 mm -Dimensions: Ø 225 x 165 mm -Weight: 8.1 kg

Condition: used, Year of construction: 1988, turning diameter over bed 2000 mm turning diameter over slide rest / mm turning length / mm - Type 1 K 671 320 F3 - Year of manufacture 1988 (first commissioned in 1998) - Turning length 10,000 mm - Turning diameter over bed 2,000 mm (modified) - Faceplate diameter 1,950 mm - Faceplate clamping range 400 - 1,350 mm - Speeds 1.00 - 140 rpm Ndsdpfx Ajxn Tz Ioh Sjc - Torque 125,000 Nm - Main cutting force 130 kN max. - Automatic swiveling tailstock - Max. workpiece weight 70 tonnes - Max. workpiece weight with steady rest 100 tonnes - Drive power 100 kW - Number of bed ways 4 - Dimensions 22,000 x 6,200 x 2,900 mm - CNC control SIEMENS 840D (2010 for €220,000.00) - Support feed X-Z 0.3 - 4,000 mm/min. - Support rapid traverse X-Z 4,000 mm/min. - Inner cone dimensions 140 x 1:7 - The machine complies with CE guidelines - Includes 2 steady rests, 1 roller block, 4 jaws, boring device - Condition: very good condition

Condition: like new (used), Year of construction: 2001, Set of clamping cones SK 50 - like new. Hardly used. Nodpfxjxnldze Ah Sodc

Condition: used, Year of construction: 1991, Allis Chalmer 60 109 M-II Primary Gyratory Crusher 2 complete units, intake size: 1,500 mm (60 inches), cone diameter: 2,725 mm (109 inches), output size: 175 to 250 mm (7 to 10 inches), throughput: approx. 4,700 to 6,400 t/h, without electric motor (required drive power: 750 kW), including one hydraulic hammer each, total weight: approx. 570 t per unit Ndsdpjvg A Raofx Ah Ssc

Condition: new, Year of construction: 2025, Weighing unit with 10 weighing heads (large hoppers for bulky products) for very precise weigh checking, with 5.5-Liter volume each. Special design for salad or similar products: dimpled surface, adjustable rotating top cone and stronger linear feeder, stagger dump, washdown construction. - Specifications: max. speed of the machine in neutral: 40 cycles/minute; weighing range: 10-5000g, accuracy: +/- 0.5-2.0g; touchscreen (large version) operation; stainless steel; 220V, 2.0kW; L1900xW1266xH1900; 700/750kg. That machine/system is available in different versions for different packaging sizes and with different packaging speeds. Ndsdpfx Ajv Nmryeh Sec Please note that our new prices are often below the usual used prices. Please feel free to inquire and tell us your packaging task. - Usually 30-50 different new machines are available immediately from stock. In addition, we have very short delivery times from approx. 3 weeks for customized machines. Deviations from the sample photo are possible. - All machines are available with full warranty.