Used Fine Structure for sale (4,942)

Condition: used, Compact pub brewery with a 2-vessel brewhouse, tanks, bottling equipment, and utility systems. The system consists of the following components: 1. Malt mill (Summer 2017) Roller mill on a painted steel frame with a capacity of approx. 400 kg/h of malt (2.2 kW motor power), featuring a mechanism for fine, rapid adjustment of the roller gap and a bagging spout at the bottom. 2. Brewhouse (Wengert, 2018) Two-vessel brewhouse with a mash/wort kettle and a lauter tun made of stainless steel with copper-clad lids. The kettle (nominal capacity: 500 l) is equipped with a top-driven two-blade propeller agitator and is fired by a gas burner (Weishaupt). The lauter tun is equipped with a rake, a drop floor, and a side spent grain flap with a chute. The brewhouse features a control system (Movonik, 2017) for automating temperature control and agitator speed. The brewhouse is mounted on a stainless steel frame that includes a wort pump, control cabinet, control unit with touchscreen display, and various pipes, valves, and fittings. Wort cooling and aeration are provided by a freestanding two-stage plate heat exchanger and a wall-mounted wort aeration unit. 3. Fermentation/Storage/Pressure Tanks/Transport Tanks - Open fermentation vat (Speidel) with a capacity of 675 liters. The vat is equipped with a temperature sensor and temperature control unit, jacket cooling, a lid, and outlet lines at the bottom and in the lower section of the frame. - 5 cylindroconical fermentation and storage tanks (Mueller, 2017), each with a capacity of 1,250 liters, 2 cooling zones, and up to 3 bar of overpressure. Each tank is equipped with a temperature sensor, its own temperature control unit, a pressure gauge, a bung, a sampling tap, a cleaning line, and a discharge line with a manual valve. - One cylindroconical fermentation and storage tank (Mueller, 2017) with a capacity of 625 liters, 2 cooling zones, and an operating overpressure of up to 3 bar. The tank is equipped with a temperature sensor and temperature control, a pressure gauge, a bung, a sampling tap, and cleaning and discharge lines with manual valves. - 4 horizontal dispensing tanks (Mueller, 2017), each with a capacity of 520 liters, a cooling jacket, and up to 3.9 bar overpressure. The tanks are mounted on a shared stainless-steel truss structure. Each tank is equipped with: a temperature sensor and its own temperature control unit, sight glasses, a sampling valve, a hose-type level indicator, a pressure gauge, and a discharge line with a manual valve. A four-line CO₂ pressure-reducing station is also located on the side of the tank group. - Horizontal transport tank (Mueller, 2019) mounted on a frame with fork rails and jacket cooling. The tank has a capacity of 1,020 liters and can withstand up to 3.9 bar of overpressure. Equipped with a pressure gauge, safety valve, sight glasses, and a discharge line with a manual valve. Suitable for use with tank liners. 4. Filling - Batch bottle washing machine on a mobile stainless steel frame for processing up to 10 bottles per cleaning cycle. Additional equipment includes a centrifugal pump, a detergent tank, a fold-down stainless steel hood, and various pipes and fittings. - Filler for party cans and siphons (Leicht, 2018) with two filling stations. Semi-automatic, mounted on a stainless steel frame with various fittings and controls. 5. Utilities - Stainless steel hot water tank with electric reheating via screw-in heating elements with a power rating of 7... Tjdjztpxmjpfx Abujd

Condition: refurbished (used), Year of construction: 2009, Benier MS 500 bread moulder,The MS500 moulding system is specially designed for dough consistencies, which have to be degassed for a fine regular internal crumb structure. White, wheat, wholewheat or all other type of flours can be processed each with their own moulding settings in order to achieve the optimum result. equipped with a teflonised infeed hopper in order to centralize the dough pieces stainless steel curling net between moulding head and pressure board pressure board with v-shaped pattern and independently adjustable side guides Tedpozfld Njfx Abujd weight range 50-1200 grams output max 2200 pcs/hr moulding length min. 130 mm – max. 450 mm year of build 2009

Condition: new, maximum load weight: 33,865 kg, overall weight: 48,000 kg, axle configuration: 3 axles, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately and in the short term, on our website. The following is an excerpt of the equipment. Complete equipment available upon request. Gooseneck: Gooseneck with angled front corners at approximately 45° and rear slope of approximately 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN) Hardwood flooring approximately 30 mm thick Loading platform: Double-extendable design with rear slope of approximately 500 mm x 8°. 6 pairs of lashing rings that fold outwards (LC 5,000 daN) 4 pairs of lashing rings that fold outwards (LC 10,000 daN) 1 pair of lashing rings horizontally at the front of the loading platform (LC 10,000 daN) 1 intermediate table, approximately 250 mm Hardwood flooring approximately 48 mm thick, checkered steel plate over the axles Cutouts in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) Axles: BPW axles and suspension; all axles hydro-mechanically steered. Technical axle load: 12,000 kg each Air suspension with lifting and lowering valve Axle tool Tires: Tires 245/70 R 17.5, load index (146/146 F) Brand of our choice Kingpin: JOST kingpins (mechanical) with 2-speed gearbox for an approximate lifting capacity of 24 tons (approximate test load of 50 tons) Braking system: Braking system in accordance with EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit Paintwork: First-class and durable corrosion protection High-quality 2-component (2K) topcoat, single color in RAL 3002 carmine red Rear section metallic and painted in RAL 9010 (pure white) Steel structure: Steel structure made of high-strength fine-grained steels. Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Electrical system: Electrical system in accordance with EU regulations Lighting 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connecting bar with 24N, 24S & 15-pole sockets according to ISO. 24N ISO-1185 24S ISO-3731 15-pole ISO-12098 Including the following additional equipment: 2-inch kingpin Galvanized steel front wall, approximately 400 mm high Yellow-red air couplings on the galvanized front connecting bar A spare wheel holder in front of the front wall Electro-hydraulic unit Rear steering from front and rear, operable via cable remote control with pushbuttons, with single-axle steering control (without installation in the tractor unit) Mounting on the rear area of the gooseneck for aluminum ramp plates Mounting rail for aluminum ramp plates at the rear of the vehicle Tedpfsz Sh Htjx Abusd Galvanized folding supports under the slope of the loading platform Aluminum side walls and rear wall on the gooseneck, plug-in design, approximately 2,440 x 400 mm (L x H) The rear galvanized plug-in edges are removable (overall length approximately 2,560 mm) A galvanized toolbox, integrated into the angled gooseneck 4 pairs of WADER container pockets in the loading platform for a 20', 2x 20', 40' or a 45' container 8 pairs of pocket holders for plug-in edges approximately 100 x 50 mm in the outer frame of the loading platform Extensions galvanized, extendable by approximately 230 mm on each side Sliding mounting rails for aluminum ramp plates at the rear of the vehicle 2 pairs of ferry rings under the gooseneck and 2 pairs at the rear Central lubrication system with 2 BEKAMAX (Pico) pumps with normal grease NLGI-2 and removable protection around the pump 2 LED reversing lights mou

Condition: used, Year of construction: 2026, functionality: fully functional, CORMAK FM350 Dust Collector – Industrial Sawdust and Chip Extraction System The CORMAK FM350 is an industrial-grade dust extraction system designed for efficient and reliable removal of sawdust, chips, and fine particles in professional woodworking facilities. Thanks to its powerful suction performance, large-capacity collection bags, and the ability to connect up to four woodworking machines simultaneously, the FM350 provides effective dust control even in demanding production environments. Key advantages Powerful 3.8 kW motor (400 V) – ensures reliable continuous operation in industrial conditions. High airflow capacity of 4,860 m³/h – efficiently removes large volumes of sawdust and wood chips. Heavy-duty metal centrifugal fan – durable steel impeller provides quiet, vibration-free operation. Robust steel construction – powder-coated finish protects against corrosion and mechanical damage. Adjustable leveling feet – allow precise positioning even on uneven floors. Six 200 L collection bags – large waste capacity reduces the frequency of emptying. Quick bag replacement system – steel clamps enable tool-free and fast bag removal. Connection for up to four machines – suction manifold with 1 × Ø180 mm and 4 × Ø100 mm outlets provides flexible installation options. Construction and technology Tjdpfxj Afnk Nj Abuod The CORMAK FM350 is equipped with a durable steel centrifugal fan and a reinforced support structure designed for intensive industrial operation. High-quality components ensure resistance to overloads and long-term reliability. The modern bag mounting system allows quick maintenance and convenient replacement of filtration and collection bags. Precision and performance Thanks to large-surface fabric filter bags and high suction pressure, the CORMAK FM350 dust extractor provides excellent working conditions even during heavy-duty woodworking operations. Effective dust removal improves air quality, increases operator comfort, and contributes to a safer production environment. Applications The CORMAK FM350 is designed for: wood processing plants – extraction from saws, planers, routers, and other woodworking machines professional carpentry workshops requiring multi-machine extraction technical schools and training facilities large industrial halls requiring a high-capacity sawdust extraction system Standard equipment 3 fabric filter bags 3 fabric collection bags Suction manifold: 1 × Ø180 mm / 4 × Ø100 mm Optional equipment Galvanized hose clamps 3-micron filter cartridge Technical specifications Parameter Value Extraction capacity 4,860 m³/h Collection bag volume 3 × 200 L Number of bags 6 Suction connections 1 × Ø180 mm, 4 × Ø100 mm Dimensions (L × W × H) 2355 × 590 × 2150 mm Weight 125 kg Motor power 3.8 kW Power supply 400 V / 3-phase PLEASE NOTE!!!! This machine is a returned item; it comes without its original packaging or splitter. NO WARRANTY AND NO RETURNS!

Condition: new, Year of construction: 2026, sheet width 3100 mm plate thickness 9 mm pre-bending 6 mm diameter of upper rolls 220 mm diameter of lower rolls 200 mm side roll diameter 170 mm min. dia. 250 mm roll speed 6 m/min total power requirement 10,3 kW weight of the machine ca. 4651 kg dimensions of the machine ca. 4915 x 1120 x 1235 mm Features - Machines include the following DAVI standard specification: The components of the machine structure (machine stand, frame and swivel bearings, etc.) have been calculated and designed to withstand the loads required for the applications and performance levels. The robust and heavy-duty machine construction absorbs the loads generated during the bending process without transferring them to the foundation. - High-quality surface finish: For forming delicate surfaces and/or soft materials without leaving marks Hydraulic-mechanical parallelism system, supported by electronics for fine-tuning. There are two INDEPENDENT & SYMMETRICAL hydraulic circuits for the left and right cylinders of each roller. The oil flow is regulated by two DOUBLE PUMPS, which are mounted on the same motor shaft and are fully synchronised. The two symmetrical hydraulic circuits move the cylinders and supply the rollers with the SAME amount of oil in a fully synchronised manner. Electronic control is activated only for extremely precise fine-tuning. - Smooth transmission of the drive Both the hydraulic motors and the gearboxes (top and bottom) can follow the deflection of the roll without load when bending narrow sheets. This ensures perfectly symmetrical deflection of the rolls under load. This system also allows the rollers to deflect freely, without the risk of breakage under excessive load. - ‘Roll-by-Wire’© digital technology Since 2004, DAVI has revolutionised the way sheet metal rollers are wired (similar to ‘fly-by-wire’ technology in the aerospace, FMS and automotive industries) and introduced ‘Roll-by-Wire’ technology. This allows the entire control system of the roller to be controlled via digital signals rather than, as was previously the case, via numerous relays and contacts. Digital technology is much faster and more reliable. Action Benefit Reduction in the number -> Reduction in potential of components component failures Very compact design -> Improved accessibility for maintenance work Improved accessibility for -> Damaged parts can be identified maintenance work more easily Tsdpfoz Dxpmox Abujd More reliable -> Greater accuracy thanks to the use of ‘digital signals’ Permanent lubrication technology The lever-arm feed system eliminates all linear friction during the movement of the side rollers, as the roller support arms, which house the bushings, rotate simply and smoothly around two large, strong pivot points made of alloy steel, ensuring precise and friction-free rotation. This guarantees reduced wear and safety during unlimited use. Further advantages of the lubrication-free lever-arm feed mechanism are: •NO daily maintenance required (lower operating costs). •More production time available. •The bearings are sealed to protect against scale, dust and rust - Hardened rollers •Excellent heat tre...

Condition: used, Year of construction: 2019, functionality: fully functional, machine/vehicle number: AN2018080, total length: 12,860 mm, total width: 4,806 mm, type of input current: three-phase, input voltage: 400 V, feed length X-axis: 3,000 mm, working width: 350 mm, power: 25 kW (33.99 HP), TRC 1500 – Timber Repair & Cosmetic Machine Technical Description • System Overview • Process Workflow System Overview The Wintersteiger TRC 1500 is a fully automated industrial system designed to detect, repair defects in wooden boards. It combines advanced 3D scanning, high-pressure thermoplastic injection technology to deliver consistent, high-quality repairs at production speed. Defects are repaired with thermoplastic filling material using injection and application units. No filling material is wasted thanks to the precise calculation of the filling quantity and precision injection. the edges can also be filled. Key Features • Automated 3D laser triangulation defect detection • High-pressure thermoplastic injection for durable repairs • Precision finishing unit for cosmetic perfection • Independent melt temperature zones with 8 kg tank • Closed glycol-water cooling system for controlled solidification • Ethernet-based control system with remote maintenance • Unlimited product profiles and intuitive scanner interface Product Range (Workpiece Specifications) Length 500–3000 mm Width 100–350 mm Thickness 3–30 mm Production speed upto 10 m/min – depending on number and sizes of defects Filling System – Injection & Application Units • Injection Unit: • 3-axis positioning (X/Y servo-driven, Z pneumatic) • Pressure-regulated melt feed • High-pressure injection • Application Unit: • 3-axis control • Fine finishing of repaired areas Faulty Spot Eye Scanner • 3D laser triangulation and high-speed camera system. • Detects defects from approx. 1 mm depth • Automatic height adjustment • 2D + 3D measurement • Adjustable parameters for wood types Melting Unit • 8 kg tank • Independent temperature zones • Integrated piston pump for constant pressure Cooling Unit • Closed glycol-water circuit • Stable temperature control Control System • Ethernet-based communication with remote maintenance • Access to PLC, scanner, servo drives • Energy-efficient regenerative drive technology Scanner Software • Processes 3D light-section profiles • Calculates defect volume and coordinates • Unlimited product programs • Intuitive operator interface High-Pressure Injection Process 1. Melting of thermoplastic material 2. Pressure and temperature regulation 3. Targeted injection into defect 4. Immediate cooling 5. Minimal surface residue • Benefits: • Low material usage Todpfxsx Dmdho Abujd • Excellent adhesion • No alteration of surrounding wood structure System Architecture • Melting unit • Heated hoses • Injection head • Cooling plate • Cooling unit with supply/return flow

Condition: good (used), Year of construction: 2013, functionality: fully functional, working width: 300 mm, passage height: 340 mm, Three-sided brush sanding machine / brush machine Manufacturer: Houfek Type: Twingo 300 Year of manufacture: 2013 Working width: 300 mm Passage height: approx. 340 mm 1x sanding brush unit, vertical, from the left, speed infinitely adjustable 1x sanding brush unit, vertical, from the right, speed infinitely adjustable 2x sanding brush units, horizontal, from above, speed infinitely adjustable Tedpjzg S Nzsfx Abued Feed rate infinitely adjustable Machine weight: approx. 690 kg Includes various sanding and structuring brushes on a separate pallet.

Condition: used, maximum load weight: 30,660 kg, overall weight: 43,000 kg, axle configuration: 2 axles, first registration: 03/2024, next inspection (TÜV): 03/2025, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpt from the equipment: Complete equipment available upon request. Loading Platform * Low-bed with central beam in extendable design * Length approx. 6,750 mm * 5 pairs of lashing rings that fold outwards (LC 5,000 daN) * 1 pair of lashing rings that fold outwards (LC 10,000 daN) * 1 pair of lashing rings lying horizontally at the rear of the loading platform (LC 10,000 daN) * The supply lines are protected in the central beam and adapt to the respective low-bed length. Gooseneck * Length approx. 3,900 mm * Gooseneck hydraulically adjustable up/down and extendable * Technical saddle load: 23,000 kg Rear Chassis * Short design with closed outer frame and diamond plate cover * Chassis with excavator well, which is closed in the rear half to accommodate the air tanks * 2 pairs of lashing rings that fold outwards (LC 5,000 daN) * 1 pair of lashing rings that fold outwards (LC 10,000 daN) Axles * BPW axles * Hydro-mechanically forced steered * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve * Axle tool Tires * 245/70 R 17.5 3PMSF – Manufacturer of our choice, load index (146/146F) Braking System * According to EU regulations with EBS-E (2S2M) without connection lines to the tractor unit Steel Construction * Made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Paintwork * High-quality 2-component (2K) * Topcoat in solid color RAL 3002 carmine red Incl. the following additional equipment: * 2-inch kingpin * One galvanized steel front wall, approx. 400 mm high * One spare wheel holder in front of the front wall * Yellow-red air couplings on the galvanized connection strip at the front * 4 wheel chocks with bracket. (± 5 kg) * Steering from the front and rear via cable remote control, operable via push buttons, with single-axle steering control (without installation in the tractor unit) * Electro-hydraulic unit (± 45 kg) * Yellow reflector tape according to EU regulations on the side, on the extension, and at the rear of the trailer * 1 wooden block, approx. 500x250x200 mm * Attachment rail for aluminum loading ramps at the rear of the vehicle * One bracket for a rotating beacon at the rear of the trailer * One mud flap at the rear of the trailer * European reflector plates (red-yellow) at the rear of the trailer * On the gooseneck and at the rear panel, one bracket each on the left and right for warning signs including socket * Manual and description on a USB stick * Speed stickers 80 km/h at the rear and on both sides * Load gauge for determining axle loads including load diagram * Incl. special accessories: On the gooseneck, aluminum side and rear walls, plug-in, approx. 2,440 x 400 mm (L x H) Tedpfx Abozvt Tysuod * The rear galvanized end crossbars are removable. (Length of the structure approx. 2,560 mm). (± 46 kg) * On the gooseneck, a separate air connection with an air gun. * 2 work lights with a switch on the trailer, mounted on the gooseneck platform on the left and right * 6 pairs of rung pockets for end crossbars approx. 100 x 50 mm in the outer frame of the loading platform * 2 pairs in the outer frame of the chassis (± 29 kg) * Extensions, galvanized, extendable by approx. 230 mm per side (± 262 kg) * Hydraulic connections from the gooseneck to the low-bed with multi-coupling instead of screw co

Condition: used, Year of construction: 2019, color: grey, overall weight: 16,000 kg, maximum load weight: 13,200 kg, empty load weight: 2,800 kg, loading space volume: 45 m³, loading space width: 2,460 mm, loading space length: 7,300 mm, loading space height: 2,520 mm, first registration: 06/2019, axle configuration: 2 axles, total length: 7,300 mm, driver cabin: day cab, emission class: none, Equipment: truck registration, Vehicle number for inquiries: 41947 Gnipol, NW745SF * Year of manufacture: 2019 * 7.45 [presumably meters, referring to trailer length] * Fixed roof * Load securing rail * Portal door * Furniture version * Telescopic support legs * Galvanized * Other * Gross vehicle weight: 16,000 kg * Unladen weight: 2,800 kg * Payload: 13,200 kg * Permissible gross vehicle weight: 16,000 kg * Interior dimensions: L = 7300 mm, W = 2460 mm, H = 2520 mm * Interior volume*: 45 m³ * Dimensions of corner brackets: E = 5853 mm * Dimensions of overhang: 799 mm * Lowering height: 1320 mm * Pallet spaces: 18 * 3-row load securing rail * Telescopic support legs * Adjustable lowering height * Light band Disclaimer: Subject to changes, prior sale, and errors. You can find more pictures and videos on our website. Todpfe Ad Ui Nsx Abued Our extensive service includes, for example: * Purchase / sale / rental of commercial vehicles * Fast and uncomplicated financing * Application for all (export) documents * Ordering of export license plates / customs license plates * Vehicle preparation: new tarpaulins, lettering, paintwork, etc. * Professional loading / load securing * TÜV inspections, registration service * Transfer of commercial vehicles Please ask our trained staff; we will be happy to advise you.

Condition: used, Year of construction: 2006, Main areas of application: Animal feed industry: Production of high-quality sinking or floating fish feed and pet food. Food industry: Processing of cereals, protein concentrates and structured food ingredients. The Kahl LTW 160 twin screw extruder is a high-performance industrial machine from the German manufacturer Amandus Kahl, primarily used for mixing, kneading, cooking, and shaping viscous materials (such as animal feed, fish feed, or food components). The machine is characterized by its modular design and integration into complete, turnkey production lines. Format: Screw diameter (??): 160 mm Equipment: Tedpfovfxqyex Abuod 1 x feed table, 1 x tube chain conveyor, 1 x mixer 1 x water addition, 1 x extruder, 1 x supply air fan, 1 x cyclone, 1 x rotary valve, 1 x distributor, 1 x belt dryer, 1 x product hopper, 1 x tube chain conveyor, 1 x fine grain hopper, 1 x fine grain discharge, 1 x fine grain bag, 1 x supply air fan, 1 x belt dryer, 1 x rotary valve, 1 x dust bag, 1 x exhaust fan, 1 x airflow rotary dryer, 1 x dedusting, 1 x tumbling screen, 1 x bar removal, 1 x final packaging 1 x belt unit, type: BTK 1510-0 refurbished 2016

Condition: used, Year of construction: 2006, overall weight: 16,000 kg, maximum load weight: 12,400 kg, empty load weight: 3,600 kg, loading space width: 2,460 mm, loading space length: 7,200 mm, loading space height: 2,400 mm, Equipment: cooling unit, GERMAN DEALER offers: Schmitz BDF refrigerated box trailer Tjdpfx Abe Ahdtpousd Carrier 850 unit in working order new battery 2 rows for locking bars skirt board 16,000 kg GVWR 3,600 kg unladen weight Year of manufacture: 05/2006 Interior dimensions: 7200x2460x2400 mm Many swap bodies and chassis are in stock! ##### DELIVERY IS POSSIBLE THROUGHOUT GERMANY! MEPO COMMERCIAL VEHICLES HAS BEEN PROVIDING VEHICLES SINCE 1983! VIEWING BY APPOINTMENT ONLY! #####

Condition: new, axle configuration: 3 axles, permissible axle load (axle 1): 10,000 kg, permissible axle load (axle 2): 10,000 kg, permissible axle load (axle 3): 10,000 kg, loading space length: 29,000 mm, loading space width: 2,540 mm, loading space height: 2,850 mm, total length: 29,000 mm, total width: 2,540 mm, total height: 2,850 mm, suspension: air, tire size: 385/65-R22.5, Equipment: ABS, - BPW axles Tsdo Aba Iropfx Abusd - EBS - Air suspension - Disc brakes - Central lubrication system NEW MAX210-Z-3AA-13.60-22.5-2.54, available directly from stock Technical data MAX210-Z-3AA-13.60-22.5-2.54 Total weight: 48,000 kg / Coupling pressure: 18,000 kg / Axle load: 30,000 kg / Tare weight: 11,456 kg / Payload approx.: 36,544 kg / Coupling height (laden): 1150–1250 mm / Turning radius: 2300 mm Loading area length: 13,600 mm / 2-way extendable (2 x 770 mm) to 2900 mm / Wheelbase: 1810 mm Technical description: Extendable loading area with pneumatic locking / A fixed intermediate table of ± 250 mm is located in the central box structure. / 8 pairs of lashing eyes that fold outwards (LC 5,000 daN) / 3 pairs of lashing eyes that fold outwards (LC 10,000 daN) / Recesses in the outer frame for attaching lashing straps (LC 2,000 daN) Tires: Tires 385/65 R22.5 (Brand: Goodyear) Tire pressure monitoring system (TPMS): TPMS according to ECE R 141 Axles: BPW axles with disc brakes, air-suspended with raising and lowering valve. All axles are hydromechanically steered. Technical axle load: 10,000 kg (ET 0) Braking system: WABCO braking system according to EU regulations with EBS-E system (2S2M), without connecting cable to the tractor. Steel structure: Steel structure made of high-quality fine-grain steel. Steel grades: S355J2+N/S355MC (Yield strength 355 MPa) / S690QL/S700MC (Yield strength 690 MPa) Electrical system: Electrical system according to EU regulations, lighting 24 V ASPÖCK-NORDIK (ASS3). ASPÖCK-UNIBOX on the galvanized connection strip at the front with 24N, 24S and 15-pin sockets. Connections according to ISO / 24N ISO-1185 / 24S ISO-3731 / 15-pin ISO-12098 Warning signs: Below the gooseneck and at the rear, left and right, holder for warning signs with socket. Options: • Maneuverability at the front and rear via cable remote control with PDC light control for axle alignment. (without mounting on the tractor) • Electro-hydraulic unit (approx. 45 kg) • 2 wheel chocks with holder on the partition wall • Kingpin 2" • Galvanized steel partition, approx. 1600 mm high. EN12642-XL • White reflector tape according to EU regulations over the entire length and width. Red at the rear. • EU marking plates (red-yellow) at the rear of the vehicle. • Holder for a rotating beacon at the rear of the vehicle. • Loading floor made of 30 mm thick hardwood, reinforced with omega profiles (approx. 298 kg). • 10 pairs of stake holder, approx. 100 x 50 mm, in the outer frame of the loading floor. • 1 spare wheel holder under the loading floor on the right. • BEKAMAX (Pico) central lubrication system with 2 pumps. • 6 pairs of recesses in the loading floor for WADER container locks, for 1 x 20', 2 x 20', 1 x 40' or 1 x 45' container. • 5 pairs of stake profiles, mounted across in the loading floor, for stakes 100 x 50 mm • Galvanized storage compartment under the loading floor (2390 x 720 x 400 mm) • Rope hooks (8 mm), every approx. 500 mm below the edge profile of the gooseneck and the loading floor • Ladder, mounted on the left in the direction of travel • Stainless steel toolbox • LED lighting • 10 pairs of twist locks (100 x 50 mm, length 1000 mm) • 8 container General information Year of manufacture: 2026...

Condition: as good as new (ex-display), Demonstration Machine The professional brushing machine from Holzprofi is designed for final surface finishing tasks, including fine sanding, structuring, ultra-fine sanding, and other finishing operations. The surface result depends on the tools used. Standard Features: - 2 height-adjustable rubber-coated pressure rollers - Height scale with roller height display - Electrically adjustable roller height - Automatic star-delta switch Tedjvrvwqspfx Abued - Machine is CE compliant Technical Data: Working width: 400 mm Max. tool diameter: 300 mm Mounting shaft diameter: 40 mm 2 feed speeds: 4.5 / 9 m/min Motor output S1 at 100% duty: 5.5 HP (4 kW) Max. workpiece height: 300 mm Brush roller RPM: 1140 rpm Brush diameter: 120 - 300 mm Machine dimensions (L x W x H): 1500 x 1000 x 1750 mm Weight: 435 kg Additional equipment available on request Extras not included in the price (Representative image)

Condition: ready for operation (used), Year of construction: 2012, functionality: fully functional, machine/vehicle number: 20110006, Finecut WMC precision cutting machine. The machine is in working order and can be tested. Working area: 500 x 500 mm Maximum material thickness: 50 mm Tedpj Afdh Defx Abuod The machine is supplied without a high-pressure pump.

Condition: new, Year of construction: 2024, New machine Year of manufacture: 2024 Technical data Table size: 1100 x 760 mm Table height: 905 mm Milling spindle: 30 mm with quick-release nut Clamping height: 140 mm Height adjustment: 125 mm Dust extraction port: 2 x Ø 120 mm Stepless speed control: 1500-10000 rpm Motor power: 7.5 kW (10 hp) Net weight: approx. 880 kg Technical description 7" touch control, optional, top and bottom Tedpfjx N Dhdox Abujd 7" capacitive touchscreen, also operable with gloves (e.g., Maxi Flex) Language selection: German, English, French (other languages on request) Tool zero point selectable in the program, 3 reference points Simple menu structure thanks to innovative touch control (max. 2 levels) Display (working screen) for tool and program number, height, angle, speed, and milling stop Operating hour counter Warning messages for incorrect operation Remote maintenance via the Internet (VPN tunnel) USB interface for data backup and loading of tools, programs, and users Tool database for 5 tools (20 programs possible per tool) Heavy-duty table milling machine with a double-sided swiveling, fixed milling spindle for a swiveling range of +/- 45.5° 2-axis positioning control for height and swivel adjustment Electronic position and speed indicators Stepless speed control: 1500-10000 rpm, 7.5 kW motor with 11 kW frequency converter Push buttons with electronic soft start Left and right rotation Tool quick-clamping device Finely planed gray cast iron table with a rigid frame support Milling stop 301: overall adjustment is carried out manually via 1 handwheel on the right side; adjustment range approx. 140 mm, scale display, overall stop via touchscreen +/- 0.1 mm, partial stop adjustment (chip removal) +5 mm to -25 mm is carried out via a star-grip screw on the left side, scale display via a mm nonius, clamping to the machine table manually via clamping lever screws, milling stop made of aluminum die-casting with 2 planed cast iron guide rails 500 mm long with aluminum splinter guards, maximum possible tool diameter is 250 mm Machine socket Lockable main switch Electronic, wear-free motor brake Milling protection and pressure device GAMMA V 1629 Arc milling stop 1639 Tapoa Milling spindle 30 mm with quick-release nut CE compliant including: - Milling stop type 301 - Cast iron guide plates and aluminum splinter guards - Milling protection and pressure device GAMMA V 1629 - Table slide for table top 1100 x 760 mm, surface coated, for quick, comfortable, and tool-free adjustment to different tool diameters up to max. 240 mm, including front table insert with quick-release locking up to tool diameter 155 mm instead of standard table inserts (not in conjunction with a rotary table) - Zeromaster reference dimension setting device for precise 0-point height adjustment of the milling tool to the table top for 24 V DC - Milling arbor quick-change system HSK-80 with spindle locking and milling arbor 30 mm instead of milling spindle 30 mm (higher concentricity and no sticking in the spindle as with the MK 5 or steep taper system) - Console

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2023, load capacity: 6,300 kg, power: 6.1 kW (8.29 HP), main lifting speed: 4,000 mm/min, working height: 3,200 mm, Crane system with 2 ABUS traveling cranes (each with a lifting capacity of 6,300 kg) TECHNICAL DETAILS Number of traveling cranes: 2 Lifting capacity per traveling crane: 6,300 kg Main lifting speed: 4,000 mm/min Fine lifting speed: 700 mm/s Working height: 3,200 mm MACHINE DETAILS FEM remaining service life assessment: 0.00 full load hours consumed Theoretical remaining service life: approx. 20 years Crane track steel structure: Double-T girders Tjdpszyl Rxjfx Abujd Power: 6.1 kW Dimensions & Weight Dimensions (L x W x H): 18,000 x 7,735 x 4,500 mm Total weight: 3,500 kg EQUIPMENT 2 ABUS traveling cranes, each with a lifting capacity of 6,300 kg Portal Crane track steel structure made of double-T girders Complete manufacturer and inspection documentation Manual Drawings Inspection reports Wiring diagrams

Condition: used, Year of construction: 2019, color: grey, overall weight: 16,000 kg, maximum load weight: 13,200 kg, empty load weight: 2,800 kg, loading space volume: 44 m³, loading space width: 2,460 mm, loading space length: 7,300 mm, loading space height: 2,500 mm, first registration: 06/2019, axle configuration: 2 axles, total length: 7,300 mm, driver cabin: day cab, emission class: none, Equipment: truck registration, Vehicle number for inquiries: 41949 Gnipol, NW745SF * Year of manufacture: 2019 * 7.45 * Fixed roof * Load securing rail * Portal door * Furniture version * Telescopic support legs * Galvanized * Other * Gross vehicle weight: 16,000 kg * Tare weight: 2,800 kg * Payload: 13,200 kg * Permissible gross vehicle weight: 16,000 kg * Internal dimensions: L = 7300 mm, W = 2460 mm, H = 2500 mm * Internal volume*: 45 m³ * Dimensions of corner fittings E = 5853 mm * Dimensions of overhang 799 mm * Lowering height: 1320 mm * Pallet spaces: 18 * 3-row load securing rail * Telescopic support legs * Adjustable lowering height Tedpj Aa If Nefx Abujd * Light band Disclaimer: Subject to changes, prior sale and errors. You can find more pictures and videos on our website. Our extensive service includes, for example: * Purchase / sale / rental of commercial vehicles * Fast and straightforward financing * Application for all (export) documents * Ordering of export license plates * Vehicle preparation: new tarpaulins, lettering, painting, etc. * Professional loading / load securing * TÜV inspections, registration service * Transfer of commercial vehicles Please contact our trained specialists; we will be happy to advise you.

Condition: new, maximum load weight: 36,020 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our full vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Complete equipment details available on request. Gooseneck: * Gooseneck with rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area: * Loading area with rear bevel approx. 1,000 mm x 8° * 5 pairs of fold-out lashing rings to the outside (LC 5,000 daN) * 3 pairs of fold-out lashing rings to the outside (LC 10,000 daN) * 1 pair of horizontal lashing rings at the front of the loading area (LC 10,000 daN) * Hardwood flooring approx. 48 mm thick, checker plate above the axles Two-piece steel ramps: * One pair of galvanized two-piece steel ramps, approx. 3,185 + 1,420 x 1,250 mm, with grating covering C40/5 (point load approx. 2.8 t on a surface of approx. 20 x 20 cm) * Ramp with hydraulically foldable ramp sections and hydraulic lifting system * Maximum load per pair: 30,000 kg Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 rigid axles, 1 steering trailing axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lock activated via reverse gear and manually * Air suspension with raise/lower valve Tyres: * Tyres 235/75 R 17.5 3PMSF – brand at our discretion TPMS: * TPMS tyre pressure monitoring system according to ECE R 141 Brake system: * WABCO brake system compliant with EU regulations, with EBS-E (2S2M), without connection lines to the tractor unit Steel construction: * Steel construction made of high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: * Electrical system according to EU regulations, LED lighting 24V ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the indicator * ASPÖCK-UNIBOX on the front connection bar with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: * HRM metallisation of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to guarantee optimum corrosion protection * Finishing coat: 2 layers 2K topcoat, solid colour RAL 3002 carmine red as per RAL system 841GL * Rear section metallised and painted RAL 9010 (pure white) * Rims in silver Included accessories: * One bracket for warning signs on the gooseneck and at the rear left and right, including socket * 1 spare wheel holder under the loading area, right in the direction of travel * 2" kingpin Tsdpfx Aboy Auhujuod * One galvanized steel front wall * Yellow-red air couplings on the galvanized front connection bar * 4 wheel chocks with brackets on the bulkhead * 3 height wooden boards * Galvanized folding supports under the loading area bevel * Bracket for rotating beacon at rear of trailer * Height-adjustable tarpaulin structure – approx. 3,960 mm * Galvanized front wall with tensioning system for sliding curtains, height adjustable by approx. 400 mm * EDSCHA roof, sliding forward on aluminum roof girder profiles (screwed to front and rear wall) * 3 pairs of sliding stakes in the loading area * The body is hydraulically extendable to the left and right at the rear by approx. 750 mm * Sliding roof with pivoting portal crossbeam * Sliding curtain with approx. 700 mm reserve length, ratchet straps at approx. 600 mm intervals. Height O

Condition: new, Year of construction: 2026, functionality: fully functional, CORMAK FM300 230V Dust Extractor with Dust Filter The CORMAK FM300 230V with a dust filter is a highly efficient and mobile dust extractor that combines powerful suction with a modern filtration system. Designed for workshop environments, it is suitable for both professional woodworking facilities and smaller workshops. The use of a 2-micron dust filter makes the machine suitable for applications where clean air is particularly important. Main Advantages of the Machine High extraction capacity – 2,800 m³/h – effective removal of chips, sawdust, and dust from one or two machines simultaneously. 2-micron self-cleaning dust filter – ensures clean air in the workshop and effective retention of fine particles. Stable metal construction – resistant to vibration and mechanical damage. Tedpfx Aboz A T T Dsusd Balanced steel impeller – ensures quiet and vibration-free operation. Compact dimensions and mobility – an ideal solution for workshops with limited space. Quick bag mounting system – convenient and fast replacement of the plastic waste collection bag. Construction and Technology The FM300 230V is equipped with a balanced metal sawdust fan that generates high negative pressure and enables stable operation for many hours. The robust frame made of steel profiles and the solid mobile base ensure structural rigidity and reduce vibration. The suction system is fitted with a Y-shaped connector (2 x Ø100 mm), allowing two machines to be connected simultaneously. The 2-micron dust filter is self-cleaning, which significantly extends its service life and improves filtration efficiency. It is an ideal choice for applications where, in addition to extracting larger waste particles, it is also important to remove fine dust generated during milling and sanding. Precision and Operating Efficiency Operating at a speed of 2,850 rpm, the FM300 230V provides highly effective removal of contaminants, contributing to cleanliness and safety in the working area. Thanks to its 1.5 kW motor and efficient turbine, the extractor maintains consistent suction power even during intensive use. Applications Small and medium-sized woodworking facilities Furniture and model-making workshops Woodworking – saws, jointers, and planers Milling, sanding, and drilling workstations Standard Equipment Metal Y-shaped connector – 2 x 100 mm Metal base with 4 castor wheels Plastic waste collection bag 2-micron self-cleaning dust filter Optional Equipment Ø100 mm extraction hose Galvanized clamps Technical Specifications Specification Value Extraction capacity [m³/h] 2,800 Negative pressure 1,800 Pa Noise level 70 dB Motor speed [rpm] 2,850 Bag capacity [litres] 153 Number of bags 1 Diameter of extraction outlets [mm] 1 x 130, 2 x 100 Dimensions (L x W x H) [mm] 940 x 510 x 1,960 Weight [kg] 64 Motor power [kW] 1.5 Power supply 1-phase, 230 V User and Maintenance Manual (DTR) YES CE Declaration of Conformity YES

Condition: used, Demo machine The professional brushing machine for finishing surfaces, fine sanding, structuring, ultra-fine sanding, and other final operations. The surface finish depends on the tools used. Standard features: - Independent height adjustment for the 1st and 2nd units - 2 height-adjustable rubber-coated pressure rollers - Scale with roller height display - Electrically adjustable roller height - Machine complies with CE regulations Technical data: Working width: 400 mm Max. tool diameter: 300 mm Clamping shaft diameter: 40 mm 2 feed speeds: 4.5 / 9 m/min Motor output S1 at 100%: 5.5 HP (4 kW) Max. workpiece height: 300 mm Working roller speed: 1140 rpm Tedsvr I Rvjpfx Abued Machine dimensions (L x W x H): 1700 x 1000 x 1750 mm Brush diameter: 120 – 300 mm Machine weight: 655 kg Equipment on request. Extras not included in the price. (Representative image)

Condition: used, Year of construction: 2010, overall weight: 16,000 kg, maximum load weight: 12,250 kg, empty load weight: 3,750 kg, loading space width: 2,490 mm, loading space length: 7,250 mm, loading space height: 2,400 mm, Equipment: cooling unit, GERMAN DEALER offers: BDF refrigerated box body Carrier 750 unit in working order 2 rows of lashing rails Baseboard protection strip Telescopic support legs 16,000 kg gross vehicle weight 3,750 kg unladen weight Year of manufacture: 11/2010 Interior dimensions: 7250x2490x2400 mm Many interchangeable platforms and chassis are in stock! Tjdpfxs Agugts Abuod ##### PLEASE CALL - NO EMAILS! ##### DELIVERY IS POSSIBLE THROUGHOUT GERMANY! MEPO COMMERCIAL VEHICLES HAS BEEN PROVIDING VEHICLES SINCE 1983! VIEWING ONLY BY APPOINTMENT! #####

Condition: new, functionality: fully functional, Year of construction: 2026, overall weight: 100 kg, total height: 1,000 mm, color: red, continuous operating pressure: 210 bar, spindle torque (max.): 1,800 Nm, Equipment: hydraulics, Cone splitter Excavator splitter Drill cone splitter Wood splitter KS5 Drill cone 200x400 - Made in Germany The powerful cone splitter for attachment to mini-excavators, excavators, wheel loaders, tractors, skidders and many other options. The drill cone can be exchanged for various tools such as a root cutter, auger, hummus sieve, concrete mixing drum, weed broom and many other attachments. The cone splitter consists of a very stable drive unit and the drill cone (splitting cone) The drill cone is completely hardened. It is not made of unhardened steel as is the case with many other manufacturers. It can be converted to other tools in a few simple steps. - Cone splitter - Root cutter - Earth auger - Weed brush - Sweeping broom - Rotary harrows NO CHINA GOODS ! WE PRODUCE IN GERMANY ! Todpeuph Uxofx Abuod THE ideal multi-purpose tool for foresters, farmers, gardeners, do-it-yourselfers and professionals Overall length 600 mm plus attachment and interchangeable system Universally applicable in construction, forestry, agriculture and horticulture For splitting heavy firewood or wood for wood chips For drilling holes in the ground, for stakes, plants and much more For removing rootstocks and tree stumps For cleaning trenches and paved areas For levelling garden areas and creating a fine soil structure You simply do the work from the excavator without any further assistance. A very solid and stable steel construction enables you to work hard and for a long time. In addition to the motor, the shaft is supported by 2 sturdy tapered roller bearings to protect against tension and pressure. The tapered roller bearings can be lubricated for a long service life. A powerful HMT 500 hydraulic motor with up to 1,800 Nm gives you the necessary torque for efficient work, from 25 l/min up to 125 l/min and 210 bar pressure Weight 70 kg included: - Drive unit with powerful HMT hydraulic motor, weight 70 kg - Drill cone with tip Ø 200 mm 270 mm/400 mm long, 6xM16 thread LK173 on the front side Total length 270 mm + drill cone tip 130 mm = 400 mm Diameter 200 mm Weight 30 kg Total weight 100 kg

Condition: used, We offer a used KARL SCHNELL 119 FD 225 D emulsifier – an industrial machine designed for continuous cutting, emulsifying, homogenizing and grinding of food products. The machine is suitable for meat processing plants, fish processing plants, production of fillings, pâtés, sauces, pastes, delicatessen products and convenience food. The KARL SCHNELL 119 FD 225 D belongs to the FD series of inline emulsifiers. Machines of this type are used wherever a very fine, uniform and stable product structure is required. The FD series is designed for high-quality emulsification and can be adapted with suitable cutting tools and drive configurations depending on the processed product. The heart of KARL SCHNELL emulsifiers is the KS cutting system, which enables intensive product size reduction in a continuous process. Depending on the application, this type of machine can operate with different cutting tool configurations, including knife systems with perforated plates. This allows the machine to be adapted to products with different structures, viscosity and technological requirements. The inline cutter operates continuously – the product is fed into the working chamber, passes through the cutting system and is discharged as a finely cut or emulsified mass. This solution helps increase production efficiency, reduce manual work and achieve repeatable product quality in subsequent batches. The machine can be used as a standalone unit or as part of a larger technological line, for example after preliminary grinding, mixing or bowl cutting. The KARL SCHNELL 119 FD 225 D is a good solution for plants looking for an efficient inline emulsifier for industrial food production. Technical data: Manufacturer: KARL SCHNELL Model: 119 FD 225 D Machine type: emulsifier Power: 74 kW / 100 HP Power supply: 400 V Frequency: 50 Hz Motor speed: 2975 rpm Control cabinet operating voltage: 3 × 400 V / 50 Hz Control voltage: 230 V AC Construction: stainless steel Application: cutting, homogenization and emulsification of food product Main advantages: continuous inline operation high power of 74 kW motor speed 2975 rpm intensive cutting and emulsification of product possibility of obtaining a fine and homogeneous mass structure Todpfxjzi U Rms Abuod suitable for fillings, emulsions, pâtés, sauces and pastes can operate as a standalone machine or as part of a technological line solid industrial construction stainless steel construction renowned manufacturer KARL SCHNELL solution for continuous production in food processing plants

Year of construction: 2017, operating hours: 2,000 h, condition: excellent (used), functionality: fully functional, machine/vehicle number: 51.I613-020-01, The IFE SORT is a density sorting machine based on the fluidized bed system for fine, dry bulk materials. The function of this air separation table is based on a combination of vibration and air technology. Heavy components are conveyed upwards by vibration, while lighter components are kept suspended by injected air and consequently float downwards. The applications include recycling and secondary raw material processing, as well as the wood, food, and mining industries. Standard version: consists of a basic unit with a perforated plate insert driven by two unbalanced motors and a fan with a motor. Nominal width: 600 mm; sieve aperture 0.6 mm Capacity: up to 3 tons/hour in recycling – however, this is highly dependent on the density and size of the material being processed. Easy adjustment: of impact angle, amplitude, inclination, speeds, etc. Design: dust-tight Control cabinet: is not included; 2 x 500 W unbalanced motors and 1 x 4 kW fan The machine was in operation at an R&D center in Israel. As the company now operates a production facility in the Netherlands, the R&D center will be closed. The machines will be transported to Europe at the owner's expense and can be delivered ex works at a port or at the production facility in the Netherlands. Todpezkup Eofx Abusd The details for optimal transport need to be clarified. The machine price does not include packaging on a pallet.

Condition: new, Year of construction: 2026, functionality: fully functional, CORMAK FM230L1 Dust Extractor with Dust Filter The CORMAK FM230L1 with a dust filter is a modern, mobile dust extractor that combines high operating efficiency with a compact design. The use of a horizontal impeller and an advanced filtration system allows the machine not only to effectively remove sawdust and wood chips from woodworking machinery, but also to vacuum production hall floors. The machine has been designed for professional woodworking facilities as well as hobby workshops. Main Advantages of the Machine Extraction capacity of 1,000 m³/h – ensures efficient removal of wood chips and sawdust from a single workstation. Balanced WhirlWind metal impeller – quiet, stable operation and increased durability. Dust filter and plastic waste collection bag – effective separation of contaminants and cleaner air in the workshop. High negative pressure and horizontal suction system – efficient extraction of even fine dust and particles. Production hall vacuuming capability – the included wide floor nozzle expands the functionality of the machine. Compact dimensions – takes up little space in the workshop. Large wheels and ergonomic handle – easy transportation in various working conditions. Construction and Technology Tedpfx Aboz A Ur Uouod The heart of the FM230L1 woodworking dust extractor is a multi-blade WhirlWind series impeller mounted horizontally in a metal housing. It provides even suction pressure and smoother operation compared to standard vertical designs. The reinforced motor operates in continuous S1 duty mode, ensuring reliability even during intensive use. Additional structural supports eliminate vibration and ensure a long service life of the suction system. Precision and Operating Efficiency The FM230L1 operates at a rotational speed of 2,800 rpm, allowing efficient extraction of sawdust, wood chips, and fine dust generated by woodworking and sanding machines. The filtration system removes airborne contaminants, reducing the need for frequent cleaning and improving operator comfort. The set includes a large floor nozzle, making the machine a practical sawdust vacuum cleaner as well. Applications Craft woodworking shops and furniture manufacturing facilities Educational and school workshops Sanders, saws, milling machines, and jointers Cleaning production halls and production lines Standard Equipment Dust filter Plastic waste collection bag Floor nozzle Metal fastening clamps Lockable, bearing-mounted castor wheels Optional Equipment Ø100 mm extraction hose Galvanized clamp Additional filter bag set Technical Specifications Specification Value Motor power (S1) 0.75 kW Motor speed 2,800 rpm Extraction capacity 1,150 m³/h Negative pressure 1,020 Pa Noise level 65 dB Bag capacity 90 l Number of bags 2 (filter + waste collection) Extraction outlet diameter 100 mm Height 1,550 mm Width 420 mm Length 800 mm Power supply 230 V Weight 27 kg The FM230L1 with dust filter is a compact and reliable woodworking dust extractor designed for everyday work with wood and wood-based materials. Choose quality, stability, and industrial-grade filtration – order today and improve working conditions in your facility!