Used Veneer Press for sale (12,787)

Condition: used, Year of construction: 2017, Automatic cold press Manufacturer: CMB Type: PFR-CCL Year of manufacture: 2017 Technical data: Motorized loading table 3,500 x 1,600 mm for manual assembly of the plates and automatic loading into the press on the 1,600 mm side. Structure made of welded steel profiles. Devices for adjusting the working height to compensate for unevenness in the floor. Steel rollers. Foot switch. PRESS Plate size: 5,500 x 1,600 mm Loading side: 1,700 mm Stroke: from top to bottom Opening: 450 mm Cold press The plates are made of steel sheet and attached to a steel frame structure. Maximum pressing force: 160 tons. Specific pressure (on 100% of the area): 1.82 kg/cm2 Specific pressure (on 80% of the area): 2.27 kg/cm2 Pressure cylinder: 12 x 80 mm Njdpfxozuzw Dj Afwolf Auxiliary cylinders: 6 x 50/30 mm Power supply: 400 Volt EU/50 Hz/3 PH. + G AUTOMATIC LOADING and UNLOADING of the plates on the lower plate, on the 3,500 mm side. The transport is carried out via a motorized MYLAR belt. The belt is activated by 2 rollers, one of which is located at the entrance and one at the exit of the press. The rollers are driven by a motor with a chain that slides on special guides. The Mylar belt rotates around the lower plate, which rests on special side supports. The belt rotates on 2 rollers, which are located at the entrance and exit of the press. The ends of the MYLAR belt are attached to special rods with devices for tensioning the MYLAR. The upper plate is covered with a Mylar film. The press plates consist of thick steel sheets that are welded to the frame structure. HYDRAULIC UNIT with pump, oil tank and valves for operating the pressure cylinders and auxiliary cylinders that move the upper plate. The hydraulic control unit is located in the upper part of the press to facilitate maintenance. CONTROL PANEL with buttons and switches. Pressure control manometer on the front of the press. UNLOADING MOTORIZED ROLLER TABLE 2,000 x 1,600 mm The unloading table is located at the exit of the press for manual unloading of the pressed plates. Exit side from the press: 1,600 mm. Note: The loading table of the press with the dimensions 3,500 x 1,600 and the unloading table with the dimensions 2,000 x 1,600 are shorter than the press table with the dimensions 5,500 x 1,600, as the press was installed in a line. Note: The technical data and descriptions are a transcript of the order confirmation at the time. The data is for informational purposes only and is not binding.

Condition: ready for operation (used), Year of construction: 2000, machine/vehicle number: 331.00465, functionality: fully functional, power: 2.2 kW (2.99 HP), input voltage: 380 V, input frequency: 50 Hz, pressing force: 16 t, stroke length: 100 mm, operating speed: 90 mm/s, overall weight: 950 kg, Model:PE6-16 Pressure/Tonnage: 16 Tons Distance Over Bed: 600mm Nlodjzux Ruspfx Afwjf Full Length Top and Bottom Tooling Guarding Control: CNC 402

Condition: used, Veneer machine with direct stacking Manufacturer: Fischer & Rückle Type: FZR15 / DAR 12 Year of manufacture: 2006 / 2014 Cross-feeding splicer For highly efficient cross-gluing of parallel-joined veneer strips into endless or component-specific veneer surfaces. The cut or rotary-cut veneers must be pre-glued with PVAc or urea adhesives. This cross-gluer is the most economical alternative to longitudinal gluers for cross-grain applications. Production Approx. 17-20 joining points/min Technical data Veneer strip length (grain direction): 350-1500 mm Veneer strip width (cross-grain direction): 50-500 mm Veneer strip thickness: 0.3-1.5 mm Equipment Feed device for efficient and convenient semi-automatic feeding of veneer strips. Plate automation for component-specific surfaces with pre-sorted components and a pre-selected number of veneer strips. Features - Perfect bonding of cut or rotary-cut veneer of all wood species, even with wavy or rippled veneer - Unique, tried-and-tested horizontal pressing system that results in fully closed, solid glue joints - Solid, robust construction for high durability, reliable and fail-safe operation - Easy operation thanks to screen, clear symbols, separate manometer with direct access, etc. - Liftable pressure bars for quick and easy access to the heating plates for cleaning - Few wear parts, low costs for service and maintenance Cross cutter For cutting to a pre-set format width (across the grain). The width is determined by two photoelectric cells that are mounted at the required distance from the cutter. Direct stacking device DAR-22 For outputting and stacking the veneer surface directly after splicing. The spliced surfaces are gently outputted and stacked on this compact direct stacking device without mechanical intervention. Min. veneer sheet length (grain direction): 350 mm Veneer sheet width (across the grain): 250 - 1200 mm Max. stack height approx. (small sheets are not perfectly aligned): 500 mm Max. stack width (across the grain) for discharge to the rear end: 1200 mm Note: Nedpfx Afozuz Hfjwslf The technical data and descriptions are a transcript of the original order confirmation. Data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2007, Heating plate press Manufacturer: OTT Type: Solid 16-32 Nljdpfxozuzxno Afwef Year of manufacture: 2007 Technical data Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Bending tool, die, upper knife, upper tool, straight tool -Tool for: press brake Nljdefcd Imjpfx Afwof -Tool as: die -Thickness: 25/13 mm -Drawing: with the pictures -Total length: 400 mm -Total height: 108 mm -Weight: 6.5 kg

Condition: used, Bending tool, die, upper knife, upper tool, straight tool -Tool for: press brake -Tool radius: 10 mm -Thickness: 20mm -Total length: 471 mm -Total height: 188 mm Nlsdpfx Afoc Sauqewof -Recording width: 80 mm -Weight: 19.8 kg

Condition: good (used), Profile bending machine, bending machine, flat iron bender, horizontal bending/straightening press -Bending/straightening press: hydraulic profile bending machine Nlodot Hmhlopfx Afwof -Base: solid construction, mobile -Hydraulic unit: unfortunately without type designation -Piston rod: Ø 55 mm / stroke: 200 mm -Individual components: see photos -Total dimensions: 1180/1060/H1000 mm -Weight: 445 kg

Condition: good (used), Veneer saw, veneer sawing machine, jointing cutting machine, fine cutting machine, fine cutting circular saw Nlodpob A Hnhefx Afwjf -Cutting length: 3000 mm -with extraction

Condition: used, Bending tool, die, upper knife, upper tool, deer foot tool -Tool: for press brake Nledecn Rdvspfx Afwef -Tool radius: mm -Dimensions: 30 x 169 mm -Length: 2500 mm -Weight: 89 kg

Condition: good (used), Year of construction: 1988, Reaction vessel, batch system, solids separator, washing trough, painter's wash station, water treatment, tool and water cleaning, filter press, chamber filter press -Manufacturer: Poligrat, chamber filter press type 470-20/2 -Model: 11 plates -Hydraulic cylinder: Stroke: 115 mm -Dimensions: 1315/920/H1720 mm -Weight: 580 kg Nljdehvfznepfx Afwef

Condition: used, Bending tool, die, upper knife, upper tool, straight tool -Tool: split, for press brake -Tool angle: 90° -Drawing: in the photos -Dimension: 33 x 170 mm Nlodpsgph Arsfx Afwof -Length: 1485 mm (1 x 855/630 mm each) -Weight: 44.6 kg

Condition: used, Bending tool, die, lower knife, lower tool, prism tool, reversible prism, 1-part die block for die bending machine, die tool, hemming tool -Tool: for press brake, die / hemming tool -Measures: see drawing in the photos -Dimensions: 150/101 / H75 mm / 150/77 / H159 mm Nledogwhvaspfx Afwsf -Weight: 7.2 kg / 11.4 kg

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, pressing force: 225 t, stroke length: 200 mm, table length: 4,100 mm, overall weight: 15,000 kg, Equipment: safety light barrier, Fully Serviced Bystronic CNC Pressbrake Available for Purchase A high-quality, pre-owned Bystronic Xact Smart 225/4100 hydraulic downstroke CNC pressbrake is currently available for sale. This 2019 machine is fully serviced, operational, and ready for immediate deployment. Key Technical Specifications Manufacturer: Bystronic Model: Xact Smart 225/4100 Year of Manufacture: 2019 Bending Capacity: 225 tons Bed Size / Working Length: 4,100 mm (4 metres) Nljdpfx Aezg Nq Nsfwof Control System: ByVision touchscreen CNC control Total Axis Configuration: 7 axis total, featuring a 5-axis backgauge (X, X1, R, Z1, Z2) Crowning: Hydraulic deflection compensation Installation Requirement: Free-standing design; no foundation pit required Core Advantages High Precision: The 5-axis backgauge and hydraulic crowning ensure exact bending angles across the entire 4-metre bed length. User-Friendly Interface: The intuitive ByVision touchscreen control simplifies setup and reduces programming time. Cost-Effective Installation: The free-standing configuration eliminates the need for expensive floor excavations or pits. Feel free to let us know if you would like us to draft a formal quotation for you

Condition: used, Year of construction: 2017, Used 3-meter press brake from Safan Type: E Brake 100 3100 Capacity: 3100 x 100 tons Y1, Y2, X, Xdelta, R, Z1, and Z2 are CNC-controlled Nedpfx Ajzh Ibvofwolf E Control Hydraulic WILA top clamping system 1 set of complete tooling Year of manufacture: 2017

Condition: good (used), Year of construction: 2012, functionality: fully functional, Bale press Dixi 60 SLD, year of manufacture 2012 Manufacturer: Dixi Type: Dixi 60 SLD Year of manufacture: 2012 Drive power: 7.5 kW, 400 V / 16.5 A Feed opening: 990 x 1,110 mm (W x L) Pressing force: 60 t Pressing cycle: approx. 47 s Bale size: 800 x 1,100 x 1,200 mm (W x H x L) Bale weight: approx. 370-410 kg Tying: 3-fold, manual Machine dimensions: approx. 4,150 x 1,725 x 2,035 mm (L x W x H) Nodpfjzk A Rdox Afwslf Machine weight: approx. 5,420 kg Material: Paper, cardboard, film Note: The press is in good condition. It has been inspected and tested. A video can be found on our website or YouTube channel. An operating manual is available. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or for any errors. The offer is non-binding, subject to prior sale, and can be revoked at any time. Inspections are possible by arrangement. The sale is made against advance payment, ex works, without any warranty.

Condition: used, Year of construction: 2008, Overview This NIKO VP11e is a horizontal pneumatic (membrane) press for whole or destemmed grapes, built in 2008 by NIKO (Nikolaj Šraml s.p., Podnanos, Slovenia). The press is made entirely of stainless steel and runs a fully automatic, multi-stage pressing program once started: grapes are loaded through the two perforated cylinder doors or axially, an internal membrane inflates against the load to extract juice at progressively increasing pressure, and the cylinder rotates between stages to break up ("crumble") the pressed cake ahead of the next drain cycle. Juice drains into a wheeled collection pan under the cylinder with a pump connection; pomace is discharged by rotating the open door face-down over the pan. The press is mounted on castors for repositioning and remains still installed and under power at the seller's winery in Spain. It can be inspected in operation on request. Technical data - Manufacturer: NIKO (Nikolaj Šraml s.p., Podnanos, Slovenia) - Model: VP11e - Year of manufacture: 2008 - Machine type: horizontal pneumatic (membrane) press for grapes, mobile on castors - Cylinder volume: 1,100 L (cylinder Ø 920 mm) - Juice drainage pan (tina) volume: 450 L - Loading doors: 2, 640 x 420 mm each - Max. working pressure: 1.7 bar - automatic multi-stage program (pre-press 0.3 bar, then 0.8 / 1.2 / 1.7 bar for whole white grapes; 0.3 bar, then 0.8 / 1.2 bar for destemmed, fermented red grapes) - Integrated blower for membrane aspiration: -0.2 bar vacuum / +0.2 bar pressure - Power: 2.9 kW, single-phase 230 V (1/N/PE), 50 Hz - Mechanical protection: IP55 - Noise level: < 75 dB - Dimensions: approx. 2,520 x 1,270 x H 1,560 mm (with axial loading extension; 2,350 mm long without it) Nljdpjzk Eqmefx Afwof - Weight: approx. 430 kg Equipment - Pneumatic membrane pressing cylinder with integrated aspiration blower - Wheeled juice drainage pan with pump connection - Electric control panel with automatic pressing programs (incl. draining cycle) - Axial loading option - Safety guard on drive elements, door interlock switch and STOP switch - OEM operating manual (Spanish) Condition Used - still installed and under power at the seller's winery. No further condition report has been provided by the seller; the machine can be inspected in operation on site. Availability Immediately. Location: Spain. Dismantling, handling, packing and truck loading can be quoted on request (EXW).

Condition: good (used), Year of construction: 2020, functionality: fully functional, Horizontal baling press Dixi 80 SLD, with lifting/tilting device, semi-automatic, year of manufacture 2020 Manufacturer: Dixi Type: Dixi 80 SLD Year of manufacture: 2020 Drive power: 11 kW, 400 V / 21 A Feed opening: 1,040 x 1,110 mm (W x L) Nlsdpeziy Dfefx Afwjf Pressing force: 80 t Pressing cycle: approx. 35 s Capacity: approx. 1000 kg/h Bale size: 1,120 x 1,120 x 1,200 mm (W x H x L) Bale weight: approx. 500-600 kg Tying: 4-fold, manual Machine dimensions: approx. 4,320 x 1,830 x 2,620 mm (L x W x H) Machine weight: approx. 8,000 kg Materials: Paper, cardboard, film Note: The press is in good condition. It has been inspected and tested. A video can be found on our website or YouTube channel. The operating manual is available. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided and any errors that may occur. The offer is subject to change, prior sale, and can be revoked at any time. Inspections are possible by arrangement. The sale is made against advance payment, ex works, without any warranty.

Condition: new, pressure 28.0 t throat 225 mm stroke 150 mm table surface area 325 x 300 mm work speed 2.0 - 9.8 mm/sek Nledpezkl Husfx Afwjf return speed 12.8 mm/sek total power requirement 4.0 kW weight of the machine ca. 650 kg dimensions of the machine ca. 1800 x 900 x 2000 mm - NC control to adjust the piston stroke - Selector switch for manual or semi-automatic operation - Flow control valve and pressure control valve - Integrated pressure gauge - Various tools can be installed on the piston - inside There is a 40 mm hole for attaching the tools

Condition: excellent (used), Year of construction: 2001, machine/vehicle number: 1301, power: 11 kW (14.96 HP), pressing force: 150 t, stroke length: 200 mm, table width: 100 mm, clearance between the columns: 400 mm, total length: 5,200 mm, total width: 1,730 mm, total height: 3,240 mm, overall weight: 10,500 kg, Equipment: CE marking, Adjustable sheet metal support arms, front side Parking station for sheet metal support arms, left side WILA crowning system Nledpfx Afszl Ahrjwef Under power Max. bending length: 3100 mm Distance between uprights: 2550 mm Max. pressing force: 150 tons Distance to table mount: 590 mm Max. stroke: 200 mm Table width: 100 mm Upright overhang: 400 mm Descent speed: 300 mm/min Working speed: 10 mm/min Return speed: 120 mm/min X-axis range: 0 - 1000 mm Number of controlled axes: 6 Crowning: Yes Power: 11 kW Length: 5200 mm Width: 1730 mm Height: 3240 mm Weight: 10500 kg

Condition: ready for operation (used), Year of construction: 2010, machine/vehicle number: 33407, functionality: fully functional, power: 37 kW (50.31 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, pressing force: 220 t, stroke length: 300 mm, operating speed: 21 mm/s, reverse speed: 200 mm/s, table length: 3,050 mm, throat depth: 400 mm, ram plate length: 3,000 mm, distance table to ram: 570 mm, clearance between the columns: 2,600 mm, oil tank capacity: 350 l, total length: 5,700 mm, total width: 2,100 mm, total height: 3,685 mm, overall weight: 14,500 kg, Equipment: CE marking, documentation/manual, safety light barrier, Technical specifications Force: 2200 kN Working length: 3000 mm Distance between uprights: 2600 mm Stroke: 300 mm Distance table – ram: 570 mm Gap: 400 mm Turbo PP5400 Approach speed: 120 mm/s Working speed: 21 mm/s Return speed: 200 mm/s Weight: 13500 kg Motor: 37 kW Oil: 350 L Weight: 14500 kg LxWxH: 5700 x 2100 x 3685 mm Table: PP8170 V-axis  EFL 130 PP8303 Upgrade 2026  Top tool clamping: PP3090 – Wila  Hydraulic top tool clamping: PP3100  PP3160 hydraulic clamping V-dies  Back gauge: PP8251 XRZ modules: X1000  Security; CE: PP3580 – lasersafe  PP8402 T1 T2 Njdpfjzkxqmox Afwjlf

Condition: ready for operation (used), Year of construction: 2012, machine/vehicle number: 34435, functionality: fully functional, power: 37 kW (50.31 HP), input voltage: 400 V, input current: 63 A, input frequency: 50 Hz, pressing force: 170 t, stroke length: 200 mm, operating speed: 21 mm/s, reverse speed: 180 mm/s, table width: 120 mm, table length: 3,050 mm, table height: 970 mm, throat depth: 405 mm, ram plate length: 3,050 mm, distance table to ram: 400 mm, clearance between the columns: 2,600 mm, oil tank capacity: 350 l, total length: 4,945 mm, total width: 2,000 mm, total height: 2,995 mm, overall weight: 11,500 kg, Equipment: CE marking, documentation/manual, safety light barrier, Hydraulic press brake LVD EASYFORM 170/30 Touch-B Year of manufacture: 2012 Serial number: 34435 Technical specifications Force: 1700 kN Working length: 3000 mm Distance between uprights: 2600 mm Stroke: 200 mm Distance table – ram: 400 mm Gap: 405 mm Turbo: PP5400 Approach speed: 128 mm/s Working speed: 22 mm/s Return speed: 200 mm/s Weight: 11500 kg Motor: 37 kW Oil: 350 L Weight: 11500 kg LxWxH: 4945 x 22000 x 2995 mm COMMAND CONTROL TOUCH-B – • Table PP8170 V-axis • EFL 90 • Top tool clamping PP3090 – Wila • Hydraulic top tool clamping PP3100 • PP3160 hydraulic clamping V-dies • Back gauge X R Z1 Z2 X’ • Safety: CE PP3580 – lasersafe Nodpszk H A Defx Afwolf • 2 supports, front

Condition: good (used), Year of construction: 2001, For sale is a TOX Pressotechnik press, model MBG 004.124. The machine features a pressing force of 40 kN (equivalent to approximately 4 tonnes) and is suitable for industrial press-fitting, joining, assembly, riveting, embossing, and staking operations. A key highlight is its current certification status: The machine remains certified until April 2027. Technical Data Manufacturer: TOX Pressotechnik Type: MBG 004.124 Product Type: Press / Press-fit machine / Joining machine Pressing force: 40 kN Maximum air pressure: 5 bar Total stroke: 200 mm Power stroke: 80 mm Year of manufacture: 2001 Machine serial number: 210192.1 Nlsdeznkvpopfx Afwsf Machine/Electrical number: 210193.1 Nominal voltage: 230 V AC Control voltage: 24 V DC Frequency: 50 Hz Power: 0.2 kW Rated current: 0.5 A Back-up fuse: 16 A Protection class: IP65 Standard: DIN EN 60204 Circuit diagram: STE 325-26 Country of manufacture: Germany Certification valid until: 04/2027 Condition: Used The press operates with a total stroke of 200 mm. The actual power stroke is 80 mm, delivering a maximum pressing force of 40 kN. The machine is suitable for tasks such as press-fitting bushings, bearings, and pins, as well as for assembly, riveting, embossing, staking, and joining operations. Please refer to the images for the exact condition and scope of delivery. "Everything from a single source: We would be happy to offer you suitable bank financing for your project." komplett-konzept.leasingo.de You can find additional presses and industrial machines—both new and used—in our shop! PD

Condition: good (used), Year of construction: 1981, pressure 300 t passage width 1100 mm stroke 950 mm table width 1050 mm table depth 1200 mm dayligth 1180 mm Nsdpfsx Uru Njx Afwjlf weight of the machine ca. 20 t dimensions of the machine ca. 2,8 x 3 x 4,5 m

Condition: good (used), pressure 250 t passage width 700 mm stroke 850 mm table surface area 2000 x 1000 mm mould height - Max./min. 355 / 1200 mm total power requirement 30 kW weight of the machine ca. 25 t dimensions of the machine ca. 4,2 x 2,1 x 5,5 m Nedpfjxcblwox Afwslf

Condition: excellent (used), 4-axis hydraulic CNC press brake with HACO-Robosoft ATS 590 Graphic control (modernized in 2008) and CE conformity. Pressing force: 135 t Bending length: 4000 mm Dimensions L x W x H: approx. 4500 x 1600 x 2320 mm Weight: 10500 kg Nlodpfjx Npiyex Afwjf Accessories / Special features: • 4-axis CNC control HACO ATS 590 Graphic Y1 + Y2, X, R for bending depth, back gauge, and top/middle/bottom gauge fingers • The gauge fingers are adjusted manually, moving them together/apart • Graphical programming and display • CE conformity through 1 working speed • Hydraulic synchronized control • Manual table crowning by adjustment via hand crank under the die with SIKO counter • Split upper tooling, as new • Continuous universal die with 4 different V-openings up to max. V = 40 mm, as new • Split additional upper and lower tooling • Collecting rail • Tooling system "PROMECAM" • 2 pcs. support arms • Fast, precise and easy to adjust • Foot switch and emergency stop • Electrically secured safety doors (right, left, and rear) • 1 working speed, rapid return • CE conformity UVV valid until 04/2027 Delivery time: immediately from stock in Dortmund, free loading onto a truck Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel / Germany