Condition: used, Year of construction: 2019, Used machine Year of manufacture 2019 only 110 operating hours! Equipment and technical data: X = 1800 mm Y = 900 mm Z = 80 mm in 18 mm Koskisen panels consisting of a milling table (X-axis), a portal (Y-axis) and a Z-axis. Milling bed in 19 mm MDF as a sacrificial plate with guide rails and slotted nuts, as a clamping method. Base frame with struts, cast with polymer concrete, prepared for transport by pallet truck or forklift. Mechanical set consisting of profile guides including guide carriages, as well as ball screws 2010 and 1605 for all axes. Shaft couplings and high-performance grease for lubricating the individual carriages, as well as energy chains including connection sets. Control set consisting of a Triple Beast, for controlling 3 axes, with Ethernet connection. Leadshine power amplifier for the fourth motor. Four stepper motors, 5.0A, 3Nm with motor cables, as well as a switching power supply with 48 V, 6.7 A, LED board for breakout board, ribbon cable and proximity sensors, small parts such as wire cables, wire end ferrules, control cable, shrink tubing and cable lugs. Fgj Ia Uneryyhkoxijb Fully installed in an aluminum housing including electrical kit and emergency stop. 21.5 inch monitor as a built-in monitor, including mini PC with Windows 7, CAD software Rhino 5.0, G-code generator Estlcam, control software Beamicon2, as well as mouse and keyboard, pre-installed in an ergonomic desk. Tool length sensor for determining the length and changing the active zero point offset. Special equipment: High frequency spindle with 2.2 kW, including union nut, frequency converter, mains filter, braking resistor and collet set. PC with 8 GB RAM and AMD processor CAD software Rhino 5.0 for creating both simple 2D data and 3D solid bodies Location: Switzerland Availability: Short term

Condition: excellent (used), machine/vehicle number: AA2/002664, 5-axis CNC machining center Table length 3548 mm Max. workpiece width 1350 mm Working area in Y-axis horizontal drilling 1221 mm Working area in Y-axis horizontal milling (front) 1350 mm Fs Iewb Urwsa Unxisgb Working area in Y-axis horizontal milling (rear) 198 mm Through clearance 180 mm Z-axis travel 400 mm Rapid feed rate X = 40 m/min; Y = 80 m/min; Z = 22.5 m/min. 5-axis spindle power – new 11 kW RAPID tool magazine 12 positions TOOL ROOM tool magazine 10 positions Max. saw blade diameter 300 mm Drilling unit: 18 vertical spindles Horizontal spindles: 8 Integrated grooving/sawing unit diameter 120 mm; 6000 rpm Xilog Plus software PC flatscreen terminal Laser positioning aid for suction cup positioning Vacuum system: 1 vacuum pump 250/300 m³ at 50/60 Hz Chip conveyor belt Operating voltage: 415 V - 50 Hz Machine weight: approx. 4200 kg

Condition: used, Year of construction: 2021, Working dimension X: 5.420 mm Working dimension Y: 1.350 mm Working dimension Z: 210 mm Number of milling spindles: 1 HOLZ-HER ChipControl: Yes HOLZ-HER 5-axes spindle 7844: Yes Main motor power: 13 kW Rotation speed max: 24.000 rpm 4th axis: Yes 5th axis: 5-axes spindle Tool clamping system: HSK-F63 Tool changer positions: 33 HOLZ-HER Tool changer 7996: Yes HOLZ-HER Tool changer 7892: Yes HOLZ-HER Tool changer 7886 Pickup tool changing position: Yes Vertical drilling spindles: 10 Horizontal drilling spindles in X: 4 Horizontal drilling spindles in Y: 2 Groove saw: in X-direction HOLZ-HER Drilling aggregate 7882: Yes Cantilever machine: Yes Machine table: Pod and rail table Two rows of stops: Yes Workpiece support aids: Yes Electronic supervision of the end-position of the stops: Yes Number of consoles: 8 Pneumatic pipe connectors: zentral 4-field processing: Yes Positioning aid: Yes Crosshair laser: Yes Vacuum pump: Yes HOLZ-HER ECO-Vac: Yes Fo Iasv I Uuae Unxisgb Number of vacuum pumps: 2 Capacity vacuum pump: 275 m³/h Special workpiece clamping system: For windows Safety device: Safety mat Chip conveyor: Yes Interface for .dxf data: Yes Control cabinet cooling: Yes Automatic central lubrication: Yes Control: PC control Conformity marking: CE mark Weight: 6.500 kg Space requirement Length: 9 m Space requirement Width: 4,7 m Space requirement Height: 2,8 m

Condition: used, Albatros Numerical Control with TPA CAD Software Working range on X-axis mm 3260 Working range on Y axis mm 1200 Working range in Z-axis N ° 2 work fields Bar worktop No. 6 electronically adjustable bars by C.N. Line laser for virtual 0 position in Y direction N° 4 pneumatic Bakelite bars for lifting the panel No. 3 electronically adjustable suction cups by C.N. for each bar with vacuum seal for fixing the panel during processing No. 1 vertical electrospindle with C-axis, with automatic tool changer with No. 10 positions, Hsk type cones Automatic tool change system with 12 positions - positioned on the machine side Drilling head with 17 spindles arranged as follows: - No. 8 verticals on X axis - N° 5 verticals in Y axis - No. 2 horizontal on X axis - N° 2 horizontal in Y axis No. 2 blade groups for making grooves on the X and Y axes Front protection and safety system with carpets Automatic lubrication system (Air conditioning system for cooling and cleaning of machine control) Vacuum pump mc/h 250 Fs Ia Uovph Hxjnxisgb

Condition: excellent (used), Year of construction: 2011, 4-AXIS MILLING AND ROUTING CENTER LOADER FOR 9 TOOLS Brand: POUWELS Model: DEF 1000 Type : SPEEDO Serial number: 135 Year : 2011 (Machine deployed and visible in our workshops by appointment) The DEF 1000 router is designed for routing all types of wood parts exclusively. It is specialized for staircase manufacturing. MACHINING CAPACITIES : Movements (machining strokes) : - X travel: 6000 mm (option installed) Y movement: 1000 mm Vertical movement (Z axis): 380 mm - Maximum travel speeds : X axis: 75 m/min Y axis: 75 m/min Z axis: 30 m/min - C axis rotation: -90 +90°. MACHINE COMPOSITION - Control panel Windows 7 Pro computer - Ethernet hub - Manual or programmed control mode : Pouwels Prostair program direct link Autocad 2008 Control system: Num 1050 Digital Drive - 3-axis routing heads 7.5 kw - 0 to 24000 rpm - Horizontal routing head with rotation ( C axis ) 7.5 kw - 24000 rpm - Fixed side tool changer for 9 HSK63 F tools ER32 collets OTHER FEATURES : - Power supply : 400v Three-phase+N+T - Installed power: 15 kW In Max 37.5A - Suction cups Ø180mm and Ø120 h.70mm - One vacuum pump 170 m3/h - Pneumatic supply: 8 bars - CE standards Fj Ia Uolc Hzwsnxijgb - Suction: centralized outlet Ø 250 mm - Recommended flow rate: 8000 m3/h (5500 min.) Overall dimensions 8300 x 3500 x 2050 mm Weight 8560 kg Please consult us for the supply of consumables, accessories and/or vacuum systems. Machine offered as is. Prices ex-store. Delivery and additional services on request.

Condition: used, No. 3218 CNC machining center SCM Record 120S Used, can still be viewed in operation Compact CNC machining center for all milling and drilling work in solid wood, chipboard, MDF and plastic Technical data (according to manufacturer's brochure): Travel X-Y-Z 2850 x 1355 x 250 mm High-performance milling spindle / milling unit 7.5 kW, 900 - 18000 rpm Automatic tool changer with 10 ISO 30 tool holders Drilling unit with 5 individually retrievable vertical drilling spindles in X 4 horizontal drilling spindles Drill holder M 10 Routolink control with 10.5” color monitor Sale on behalf of customer, ex location near 69124 Heidelberg, without disassembly, transport and assembly Disassembly, loading and transport by us optionally possible Errors in description and price excepted To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended Sold as is Technical details, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “purchased as seen” Pictures and videos serve as examples and do not represent the actual scope of delivery Fe Ia Unev Uz Hvoxisgb Terms of payment: Prices excl. VAT, payment before collection or dispatch Terms of delivery: ex location

Condition: used, Functionality: fully functional, Masterwood Winner 3.2 Working area 3100 x 1250 ISO30 Toolchanger Drillinghead Sawblade in X Fj Ia Usv T Tptenxiogb Year 1999 2 working fields ISO cones and collets Masterwork CAD-CAM 100m3

Condition: used, BIESSE ROVER35XL MACHINING CENTER Automatic bridge and suction cup movements 2 router heads, vertical and horizontal drilling Fe Ia Unjwcl Tbexijgb 2 tool changers 4th axis tooling included

Condition: used, Year of construction: 1999, Working dimension X: 3.000 mm Working dimension Y: 1.000 mm Working dimension Z: 80 mm Fs Iewby T Hea Unxisgb Number of milling spindles: 1 Main motor power: 5 kW Tool clamping system: HSK-F63 Tool changer positions: 6 Vertical drilling spindles: 14 Horizontal drilling spindles in X: 4 Horizontal drilling spindles in Y: 2 Groove saw: 90° turnable Cantilever machine: Yes Machine table: Pod and rail table Number of consoles: 6 Positioning aid: Yes Vacuum pump: Yes Capacity vacuum pump: 100 m³/h Safety device: Safety mat LED luminous tape: Yes Workpiece support aids: Yes Software: IMA IMAWOP Conformity marking: CE mark

Condition: used, Year of construction: 2003, Used machine Fs Iaekwg U Ss Unxiegb Year of manufacture 2003 New HSD milling spindle 2023 not yet in use New drilling gearbox 2020 Technical specifications: X-axis working area 3400 mm Y-axis working area 1300 mm Z-axis working area 130 mm Max. workpiece size 3000 x 1300 x 100 mm X-axis speed 25 m/min Y-axis speed 25 m/min Z-axis speed 20 m/min Milling spindle motor speed 0-24000 rpm Drill spindle motor speed 3400 rpm Milling spindle motor power 7 kW Drill spindle motor power Tool changer Interface 2.2 kW 5-way ISO-30 Brushless motor power X-axis 5.39 N/m Brushless motor power Y-axis 5.39 N/m Power Brushless motor Z-axis 2.39 N/m Number of drill spindles 15 Grooving saw diameter 120 mm Vacuum pump 100 m³/h Max. installed electrical power 15 kW Extraction hose connection diameter 120 mm Machine dimensions (L/W/H) 4500 x 2000 x 2500 mm Machine weight 2400 kg Location: Röllbach Availability: Upon request

Condition: good (used), Year of construction: 2019, CNC machine with fixed table and dual drive gantry, five axis interpolating electrospindle. Particularly suitable for SIPS panels, woodworking, plywood, MDF, plastics and thermo formed prodcuts. 6120mm x 1605mm Working field in X / Y axis 6850mm X axis stroke 1970mm Y axis stroke 1080mm Z axis stroke Max height / panel passge 700mm C axis rotation + / - 360 degrees Fj Iovpv Nboa Unxijgb 12kw electrospindle with programmable speeds from 500 - 22,000 rpm 12 Position automatic toolchanger Auxiliary 2 position toolchanger 250m3/hr vacuum pump 2 Field phenolic working table suitable for vacuum cups Hoist points to fix jigs [ series of threaded holes on table for mechanical fixing ] Set of 3 disappearing stops OSAI Series 10 CNC control including [ for example ] PC with Windows XP [ or higher ] Interactive programming Paramteric programming 3D interplolation Cutter radius compensation Extraction requirements 2200m3/hr Weight 5235kg Year - 2019 CE FULL ORIGINAL SPECIFICATION SHOWN IN IMAGES

Condition: excellent (used), Year of construction: 2017, Weeke Optimat BHX 055 Year of manufacture 2017 Main use: approx. 900 operating hours Working area X 200 – 3050 mm Working area Y 70 – 850 mm Working area Z 12 – 60 mm, special workpiece thickness: 8 mm 13 vertical drilling spindles 4 horizontal drilling spindles in X axis 2 horizontal drilling spindles in Y axis Grooving saw in X direction Milling spindle 5 kW; 1250 – 24,000 rpm 4-station tool changer (WZW) Workpiece clamping system Fe Iewakdaja Unxisgb POWERCONTROL control system with 17-inch TFT flat screen, Windows XP operating system WoodWop 7.1 including MDE and production list software Delivery includes only all tools and HSK holders shown!

Condition: excellent (used), Homag BOF 311 machining center Useful milling work area 3225 mm x 1700 mm Automatic work table with 6 bars and 3 carriages per bar Various large, medium, small suction cups 14 power clamps 58-120 04 power clamps 58-120 Tool transfer pick-up Drilling unit 21 spindles 17 vertical 4 horizontal blade 120 mm 5-axis milling unit double fork kw 15 from 1000 to 24000 rpm liquid cooling Automatic chain tool change magazine 30 positions Position for blade diameter 350 mm Drilling aggregate with 4 spindles 10 chip guide aggregate Chip transport belt Fe Ia Unjwh N Uajxiegb Vacuum pump

Condition: used, machine/vehicle number: 007601, X axis working area: 4320 mm Fgj Ia Unxju N Skfeiob Y axis working area: 2245 mm Working Table: Flat table Main Electrospindle power: 9 KW Number of controlled axes: 3 axes Total number of drilling spindles: 16 Total number of tool changer positions: 8

Condition: used, Year of construction: 2021, Working dimension X: 6.175 mm Working dimension Y: 2.250 mm Working dimension Z: 500 mm Independent Z-axes: 2 Number of milling spindles: 1 HOMAG DRIVE 5 +: Yes Vibration sensor: Yes Main motor power: 15 kW Rotation speed max: 24.000 rpm Torque support: Yes 4th axis: Yes 5th axis: 5-axes spindle Tool clamping system: HSK-F63 Tool changer positions: 28 Linear tool changer: Yes Disc tool changer: Yes Pickup change place: Yes Vertical drilling spindles: 17 Horizontal drilling spindles in X: 2 Horizontal drilling spindles in Y: 2 Groove saw: 90° turnable Gantry machine: Yes Machine table: Pod and rail table Stop for top layer protrusion: Yes Workpiece support aids: Yes HOMAG Pneumatic connection for powerClamp: Yes Number of consoles: 10 Pneumatic pipe connectors: an den Konsolen Positioning aid: Yes LED luminous tape: Yes Vacuum pump: Yes Safety device: Bumper, laser HOMAG safeScan: Yes Chip conveyor: Yes HOMAG Speed Pack: Yes HOMAG Package for abrasive materials: Yes Tool charge measurement: Yes Control cabinet cooling: Yes Fo Iewbtzqea Unxiogb UPS - Uninterruptible Power Supply: Yes HOMAG IPC Powerpack: Yes HOMAG Manual operation: Yes HOMAG Convenience package operation: Yes Control: HOMAG POWER CONTROL PC 87, Homag powerTouch Software: HOMAG WOODWOP 7.2, HOMAG WOODMOTION, HOMAG MMR, HOMAG collisionControl, HOMAG WOODWOP CAD/CAM SCHNITTSTELLE Conformity marking: CE mark Space requirement Length: 10,5 m Space requirement Width: 6,3 m Space requirement Height: 3,7 m

Condition: used, Year of construction: 2005, Used machine Year of manufacture: 2005 Condition: Functionally tested Equipment and technical data: Milling unit 6 kW, water-cooled Tool holder HSK 63 F Speed 1,000 - 18,000 rpm. Tool changer: 6-way side Drill head: 9 vertical drilling spindles in 32 mm grid Horizontal drilling spindle: 1+1 Vertical drilling spindle: 1+1 Grooving saw in X direction Control: Twin CAm 32 Vacuum pump 100 cbm/h Incl. vacuum suction cups Travel paths: X-axis: 2,685 mm Y-axis: 1,095 mm Fgj Iajkwg Rve Unxijb Z-axis: 140 mm Installation dimensions 5200 x 2843 x 1855 mm Weight: Approx. 3,500 kg Availability: by arrangement Warehouse location: Röllbach

Condition: excellent (used), Year of construction: 2019, operating hours: 54 h, Functionality: fully functional, HSK63F milling unit, maximum cutter length up to 130 mm Right and left rotation for HSK63F tool holder 3-position magazine for automatic tool change Electrical connection: 400V, 3Ph, 50Hz / 32A Motor: 5.5 kW (S1), 1000-20000 rpm. with frequency converter Workpiece width (X): min. 60 mm / max. 1000 mm Workpiece thickness (Z): min. 6 mm / max. 60 mm Workpiece length (Y): min. 250 mm in through-feed mode 5600 mm programmable workpiece length in software Workpiece weight: max. 75 kg Drilling head: PowerBlock with 21 spindles and 1 grooving saw 1 vertical drilling spindle Fs Ia Unxjwd E Tqjijgb 6 horizontal drilling spindles in Y 2 horizontal drilling spindles in X 1 grooving unit in Y Accessory package: Additional safety device via slatted curtain (required for horizontal Lamello P-System milling) Counterpressure device from above Roller table 765 mm (Y-axis), foldable, for front of the machine, width 500 mm Roller table 765 mm (Y-axis), foldable, for rear of the machine, width 500 mm Auxiliary stop 600 mm with integrated rollers for roller tables Interior lighting Extraction distributor W 160 mm / BL 80-80-80 mm

Condition: excellent (used), Year of construction: 2003, Functionality: fully functional, machine/vehicle number: 11470, workpiece width (max.): 450 mm, Hundegger K2 in very good condition, overhauled, rebuilt, and commissioned by Hundegger. Since then, it has only run for about 20 hours and was professionally dismantled and stored in a heated hall. Fgo Iswhpavoa Unxiob

Condition: as good as new (ex-display), single phase, 1950 kg, dust extraction, vacuum table with four individually controlled sections, water cooled 6kw 24000 rpm spindle, A2 hand held controller.spindle, Fj Iaohh Anre Unxiegb

Year of construction: 2000, Condition: ready for operation (used), General Data Fj Ia Uov Ezm Rjnxiegb Machine weight 5000 Main Drive Number of axis 3 Movement X-Axis Movement 3000 mm Y-Axis Movement 1480 mm Z-Axis Movement 440 mm Workpiece Workpiece X 3000 mm Workpiece Y 1000 mm This 3-axis IMA BIMA 210 100/300 CNC Wood Machining Centre was manufactured in 2000. Ideal for advanced woodworking tasks, this machine ensures precision and efficiency in operation. Consider the opportunity to buy this IMA BIMA 210 100/300 CNC Wood Machining Centre. Contact us for more information. Application Types CNC Wood Machining

Year of construction: 2013, Condition: excellent (used), Technical design: Console table 3050 x 1200 mm with manually movable 6 consoles , each console 2vacuum suction cups and a pneumatic lifting rail point laser set-up aid, vacuum pump Fj Iaekqyizj Unxijgb CNC control XILOG Plus main spindle 8,5 kW (12 HP) HSK 63F with C-axis , 1500 - 24.000 rpm tool changer plate 12-fold 1 adapter unit swiveling saw drilling head with: 12 vertical spindles, 4+2 horizontal spindles, grooving saw bumper safety system The shown tools, HSK- tool holders, drills etc. are not included in delivery!

Condition: used, Year of construction: 2022, Used machine Year of construction 2022 Equipment and technical data: GRUNDMASCHINE DYNESTIC 7507 10.7_Push Fj Ia Unevyay Eexiegb Processing length 3100 mm (without tools) CAMPUS V7 CAD/CAM software 1 x license incl. CabinetControl Base and material removal simulation upgrade "CAMPUS "" Better Nest"" Free-form nesting software " Uninterruptible power supply - UPS Milling unit 7830, power: 10.3 kW (S6/40) Chipcontrol sensor package for 3-axis spindle incl. receiver 7884 Drilling unit cpl. 14 spindles Drive power 3 kW Integrated sawing unit for sawing/grooving in X-direction n(max.) 1000-7330 min-1, infinitely variable 1 rear stop bar for processing field (field D) rear with 1 lateral stop (replaces lateral stops at the rear) Stop monitoring for 5 standard stops at the rear and right Tool changer 7873 , 6-fold linear pick-up Pneumatically liftable with integrated cover for HSK holders 2 additional holders for HSK holders for tool changer 7873. Tool changer 7872, 1-fold aggregate magazine swiveling in X and Y direction 2 x 140 m³/h dry-running vacuum pump Vacuum unit cpl, (VP8) 250 m³/h, 400V additional (upgrade) Vacuum connection cpl. 16-circuit vacuum VF16 LASER,DIRECTION CPL POINT LASER CPL OPTION ZB8 Lubrication cpl. central lubrication encoder side 2 X vacuum cups for smooth table surfaces complete 140 x 115 mm, height 30 mm with connection hose 2 X vacuum cups for smooth table surfaces complete 120 x 50 mm, height 30 mm with connection hose Conveyor belt cpl. push-off conveyor AUT 5 10.7 Push-off table Additional suction via push-off conveyor belt Pusher on moving column, controlled incl. simultaneous suction of the wear plate Direct Label 7507 label printer and complete touch label ligth option ZB74 TouchTool tool length measurement Availability: by arrangement Location: Bavaria Bavaria

Condition: used, Year of construction: 2012, Used machine Used nesting CNC from Holz-Her type Dynestic 7521 Basic machine - Dynestic 7521 20.6 Dynestic table For classic nesting processing with wear plate Machining length 6250 mm (DYNESTIC 20.6 additional 4th fence in Y already included) Machine frame in welded construction with welded and hardened prismatic guides for the traveling column, unit head and consoles Moving column in gantry design Rack and pinion drive, helical toothing, in X and Y direction, Ball screw spindles Z-direction for precise positioning Technical data: The technical data refers to the DYNESTIC 7521 - 20.6 Please refer to the corresponding data sheets. Machining dimensions: Max. Workpiece size for milling X = 6250 mm Y = 2100 mm Max. Travel distances X = 7360 mm Y = 2720 mm Z = 325 mm Max. Overtravel height DYNESTIC table Z = 1st step 318 mm / 2nd step 418 mm from top edge of table (without tools, without holder) Maximum programmable speed Vector speed: 128.0 m/min X = 80 m/min, Y = 100 m/min, Z = 25 m/min 4-stage extraction hood with pneumatic height adjustment and viewing window Voltage 400 V, 50/60 Hz CONTROL: Dual-core processor Operating system Windows XP 80 GB hard disk / 1 GB RAM RJ45 network connection 10/100 Base-T Fast Ethernet US keyboard and Microsof t InteliEy e mouse (optical) CD-ROM / CD-RW drive (CD burner) Remote maintenance Integrated network card for data transfer of control and program data. Data is transferred via high-speed Internet connection Prerequisite: High-speed Internet connection on the machine. DYNESTIC table Fixed, continuous processing table with grid division, continuous grooves in X and Y direction, Spacing of the grooves 50 mm With 25 meter sealing cord for clamping the wear plate 1 processing area with stop bars / stop Height 30 mm, can be lowered pneumatically 2 stop bars in the Y direction and 1 stop in the X direction on the right (viewed from the front edge of the machine) Vacuum fields 1-circuit vacuum system Drilling unit 7976, 24 spindles Drive power 3.0 kW 18 vertical spindles can be called up individually L-shaped arrangement, 10 in X and 8 in Y direction 32 mm grid Fgo Ijrlp Diea Unxieb Max. Drill diameter: 35 mm Total drill bit length: 70 mm from screw-on end (depending on panel thickness) Spindle stroke: 70 mm Direction of rotation: Alternating right / left rotation n(max.) 1000 - 5710 min-1 infinitely variable Mounting: M 10 thread - fit 11 mm without tools, without holder 6 horizontal spindles 2 double drilling spindles in X-direction (distance 32 mm between 1st and 2nd horizontal drilling spindle) 1 double drilling spindle in Y-direction Holder: M 10 thread, fit 11 mm Total drill bit length max. 70 mm from screw-on end without tool, without holder Free space 1 for: Optional double drilling spindle in X direction or Vertical adapter with double feed force Free space 2 for: Optional saw in X-direction or Vertical adapter with double feed force Milling unit 7831, 2-stage Power: 11.0 kW (S6) n(max.) = 1000 - 24000 min-1 infinitely variable, two-stage feed stroke max. power at 12000 min-1 to 24000 min-1 air-cooled

Condition: used, Year of construction: 2006, Used machine Year of construction: 2006 Condition: Function tested Equipment and technical data: Console machine Processing size in X: 3,200 mm Fo Iorc Ityea Unxijgb Processing size in Y: 1,470 mm Max. Travel height in Z: 325 mm Milling spindle motor: 11 kW liquid-cooled Incl. laser pointer Incl. traveling disk tool changer 7996 with 18 places 6 consoles incl. 12 vacuum cups with separate lock case unit 7982 4 pneumatic lifting and lowering loading aids Incl. manual control unit Incl. 3-field safety step mats Incl. C-axis Horizontal drilling stations: 6 Vertical drilling stations : 16 incl. sawing unit 7946 pneumatically swiveling 3.5 kW Heat exchanger for switch cabinet cooling Manual central lubrication Vacuum pump 140 m³/h - generally overhauled - CAMPUS software for CNC machining centers Weight: Approx. 4,450 kg Availability: Short term Location: Röllbach

Condition: used, Year of construction: 2007, Used machine Year of construction 2007 Nesting machine with grid table Table working area 5000 x 1240 mm X-axis travel 5665 mm Fe Istlz Ihea Unxiogb Travel distance y-axis 1650 mm Z-axis travel 325 mm max. machining height 135 mm with milling unit 7933 Motor 11 KW (S6) HSK 63, water-cooled with C-axis with disk tool changer 18-fold with vacuum pump 250 m³ with manual control unit with central lubrication with minimum quantity lubrication device Availability: short term Location: Röllbach