Used Hydraulic single column presses over 125t for sale (35)

Condition: used, Single-column hydraulic press, straightening press, punching frame ECKOLD Press frame with hydraulic cylinder, mobile press, punching unit Type RSD 1500 - 125 Machine. No. 317 / 690 Year of construction approx. 1986 Compressive force 150 ton. throat 125 mm ram stroke 35 mm Table size 280 x 210 mm Plunger surface Ø 125 mm Installation height (ram to table) max. 265 mm Table height above floor 403 mm Hydraulic operating pressure max. 500 bar - without hydraulic unit - Plunger surface with 4 M16 threads and 20 mm guide groove, central centering hole Ø 15 mm - 1 high-pressure hydraulic hose with external thread M30x1.5 mm, hose length 4 meters - 1 high-pressure hydraulic hose with union nut M30x1.5 mm, hose length 4 meters Space requirement L x W x H 700 x 300 x 1450 mm Weight 1250 kg Crjhxzjd Swtaozwwsb Good condition

Year of construction: 1974, Condition: used, machine/vehicle number: 82, Hydraulic frame press for sheet metal stamping with a force of 630 tons, designed for cold stamping. The vertical frame press with a welded construction consists of a table and an upper plate that are connected with screws. An electrical cabinet is installed next to the press and an oil overflow tank is located deep in the foundation, which facilitates filling the press system with oil. The pressing units are removable, which makes their assembly and repair easier. The press is controlled with a button. The size of the slider stroke is ensured by adjusting the position of the end stop. Cshxzzwjpgkt Sjwjrb 1. Nominal pressing force, tone 630 2. Rated working pressure of fluids, KN/cm 2,200 3. Slide stroke, mm 750 4. Slider speed, mm/s a) at idle speed 215 b) during the working stroke 10 c) during the return stroke 120 5. The greatest distance between the table and the slider, mm 1400 6. Distance between posts, mm 2200 7. Table dimensions, mm a) from left to right 2220 b) front to back 1800 8. Thickness of stamping plate, mm 220 9. Table height above floor level, mm 410 10. Nominal force of the hydraulic washer, tf 250 11. Hydraulic cushion stroke, mm 350 12. Ejector speed, mm/s a) when going up 51 13. Press size, mm a) from left to right 5070 b) front to back 3000 c) height 7065 14. Press height above floor level, mm 5480 15. Weight of the press, kg 69400 Electric motor revolutions 1450 min-1 Operating voltage 400/230 V Mains frequency 50 Hz ± 1% Rated air pressure 0.7 Pa

Condition: new, die cushion press capacity: 30die cushion returning speed: 52die cushion stroke: 200daylight: 750pressure: 150stroke: 500 Crohsd Ab Ilexzzwwjb

Condition: like new (used), 2 column hydraulic press Press force: 200 t upper stroke: 500 mm lower stroke: 200 mm overall dimension: 1800x2200x3700 mm Power: 10 PS Weight: 8.4 t Crohxoghl N Ujzzwwsb

Year of construction: 2023, Condition: new, Pressing force 150to Siemens PLC Crjhxzzwjkyu Hvoweb hydraulics Bosch/Rexroth stroke 400mm table area 600mm x 800mm

Condition: excellent (used), Year of construction: 2017, Functionality: fully functional, table height: 400 mm, pressing force: 500 t, table width: 5,500 mm, table length: 3,000 mm, TECHNICAL DETAILS capacities Maximum force: 500 t Restoring force: 200 t Table dimensions: 5,500 x 3,000 mm Table stroke: 3,500 mm Table height above floor: 400 mm Extension speed of the table: 60 - 80 mm/s Stroke of the carriage: 1,800 mm Daylight opening: 2,000 mm Cushion dimensions: 3,960 x 1,860 mm Stroke of the upper cushion stop: 180 mm Cushion force: 100 t Fast return: 35 mm/s Electrical power: 380 V, 50 Hz Output: 59 kW EQUIPMENT PLC Siemens Bolster table with dimensions of 5,500 x 3,000 mm Croheu Iy Trjxzzwweb Cooling in the control cabinet CE marking

Condition: excellent (used), Year of construction: 1995, Functionality: fully functional, - BAKER 200 T-type box press - manufacturer Germany - pressing force 200 T Cshxzsrnkdrozwwjrb - year 1995 - for straightening steel parts in two planes - infinitely adjustable clamping force from the control panel - smooth adjustment of the approach distance from the desktop - automatic operation - very good condition - complete DTR

Year of construction: 1992, Condition: used, machine/vehicle number: 530, The STEINER hydraulic press was manufactured and developed with practical aspects in mind. The hydraulic device is located on the hydraulic tank behind the press. Control blocks and valves are easily accessible from the outside and can be quickly replaced if necessary. The hydraulic radial piston pump is located on the drive console and is connected to the motor and pump mount via a coupling. The press stand is indestructible and torsion-resistant Sthal welded construction. The ironing board is screwed to the stand. The hydraulic cylinders are screwed to the press stand from above and guided through the mounting holes in the appropriate direction. The piston is connected to the piston rods via a wear ring. Four-sided, diagonal, flat grooves on the stand allow for very precise movement. Hydraulic cylinders are made of high quality material and are designed for high pressures. The piston rods are ground and hard chrome plated. The cylinder tubes are honed from the inside. Seals that have been maintained over many years are characterized by high quality and tightness. The piston rods are guided by guide bands, which are characterized by very low abrasion and a long service life. The control, control and monitoring devices for all control devices are installed in the control unit. Mutual locks ensure that no two program processes can run at the same time. The electrical control is located in a closed control cabinet. Pressing force - 8000 kN Operating pressure - 285 bar Installation height - 850 mm Stroke - 250 mm Table surface - 1550 x 1450 mm Ram surface - 1550 x 1450 mm Stand passage - 1800 mm Cehepgktcexzzwwerb Lateral Breakthrough in the stand on the right and left Width x height - 1300 x 1075 mm Table top thickness - 155 mm Width of the machine approx. - 3100 mm Depth approx. - 4300 mm Height approx. - 4660 mm Table height above hallway - 500 mm Table height under hallway - 755 mm Drive power - 55 kW Oil requirement approx. - 1400 liters Total weight approx. - 60 tons

Condition: new, More technical data on request ht curtain manual and automatic working manual stroke adjustment by camshaft switch maintenance free self lubricating 4-fold ram guiding polster plate with T-slots according to CE rules Crehxzsd Ab Igjzwwsb press force:150 tohydraulic pressure:254 bartable:1200 x 750 mmram dimension:950 x 650 mmhole in table:120 mmstroke:300 mmdistance ram-table:550 mmrapid speed:100 mm/sworking speed:5,5 mm/sreturn speed:165 mmmotor:11 kWlength:2.225 mmwidth:1.600 mmheigth:3.650 mmweight:8.200 kg

Condition: new, pressure: 125motor: 22daylight: 500stroke lenght (max.): 400table diamension: 800 x 600 x 120tappet area: 800 x 600 x 300table height: 850messurements (LxWxH): 1.600 x 2.000 x 3.200weight approx.: 7.000oil filling: 400 Control / Key switch:         1. setup mode Manual without light sensor(max. 10mm. /sec. speed). 2. automatic (full speed) with light sensor Main cylinder: Ø 220mm. Auxiliary cylinder: 2 pcs. Ø 70 x 40mm. Auxiliary guide: 2 pcs. Ø 50mm. Motor: 15kw. - 22hp. ( IE-3 ) Pump: 48Liter / ASC. Cshxzzwemr Hpcoworb Speed : flow 120mm./sec. - return 140mm./sec. - Pressure : 13mm - 5mm/sec. Installation height: 500mm. Stroke length: 400mm. Table top: 800 x 600 x 120mm. - (with T - grooves) Plunger plate: 800 x 600 x 300mm. - (with T - grooves) Table height: 850mm. (Floor to table top upper edge) ----- Accessories Hydraulics:           Hydraulic control block & accessories: REXROTH Pressure adjustment via PLC.  (10 - 60 tons) Speed adjustable via PLC. Air cooler Pre-fill valve Accessories control: Siemens S7-1200 Main control box   Swivel control panel Safety PLC. - SICK Light sensors SICK 700 + 150mm. Linear scale for adjusting the stroke length 9 PLC screen - Siemens (German & English) Movable two-hand control Ethernet connection for remote maintenance Alarm annunciator for malfunctions (candlestick & sound) 2-fold workspace lighting 8 free ON & OFF buttons on the PLC. for external connections The press complies with the machine directives Hydraulic proportional valves Dual channel cable protection Instruction manual & parts list (German + English) With side safety door (doors can be moved backwards)