Used roll benders (motor-driven) for sheet thickness over 14mm for sale (105)

Year of construction: 1973, condition: like new (used), Used BRONX Heavy Duty Initial Pinch Pyramid bending rolls. Year of manufacture : 1973. MACHINE FORMERLY INSTALLED AT ROLLS ROYCE PLC IN DERBY UK. IMMEDIATELY FOR SALE AND NOW LOCATED IN BELGUIM WHERE IT CAN BE INSPECTED. SPECIFICATION CAPACITY Two sets of dimensions which are shown below as "Prebending & Rolling" and then "Rolling only". Material Mild Steel Mild Steel Tensile strength 28/32 tons/sq.in 28/32 tons/sq.in Maximum width 11’(3350mm) 11’(3350mm) Maximum thickness at this width 2” (50mm) 2½” (63.5mm) Minimum inside diameter of rolled cylinder at maximum capacity 30’ (762mm) 37 ½’ (953mm) Maximum thickness of plate when hot rolling (finished rolling temperature 850° C.) 4” (102mm) 5” (127mm) Minimum inside diameter of rolled cylinder at maximum capacity hot rolling 40” (1016mm) 50” (1270mm) MAIN PARTICULARS Diameter of all rolls - 27” (686mm) Body length of rolls - 11’2”(3403mm) Rolling speed - 12 f.p.m. (3600mm/min) Main drive motor - 150 H.P. Slip Ring Type Two bottom roll adjusting motors, each - 50 H.P. Slip Ring Type Combined operation of swing down bearing and top roll counterbalance - Hydraulically applied Hydraulic power pack motor - 10 H.P. Electrical equipment to be suitable for operation on a supply of - 400/440 volts, 3 phase, 50 cycles CONE ROLLING ATTACHMENT: To facilitate the rolling of taper or conical forms, a skid plate is fitted to the inside of the non-drive end housing. ELECTRICAL EQUIPMENT Motors: Main Drive - 150 H.P. half hour rated – slip ring screen protected – foot mounted type. Bottom Roll Adjustments - 50 H.P. half hour rated – slip ring screen protected – foot mounted type. Hydraulic Power Pack Motor - 10 H.P. continuously rated – Squirrel cage – screen protected – foot mounted type. Control Gear: Main Drive - Drum type reversing control gear with 5 minute rated wire wound resistances, designed to pass 100% full load on the first notch or operating position in each direction. The controller will be fitted with off position interlock and limit switch rings where necessary. Bdedeh U Rzgopfx Al Usg Bottom Roll Adjustments - Drum type reversing control gear with 5 minute rated wire wound resistances designed to pass 100% full load on the first notch or operating position in each direction. The controllers will be fitted with off position interlock and limit switch rings where necessary. Hydraulic Power Pack - Direct-on-line contactor type starter, operated from a maintaining type push button station. Solenoid valves for operating cylinders are push button operated. Note: Full protection to be provided for all the above control gear by a circuit breaker, incorporating overload and no-volt protection. FEATURES AND EQUIPMENT Spare Roll included with the machine. LENGTH TBA MM WIDTH TBA MM HEIGHT TBA MM WEIGHT 95 tonnes NOTE: The information contained herein is provided in good faith, but however due to unforeseen errors or omissions cannot be binding as to accuracy.

Year of construction: 2018, condition: good (used), Make: FACCIN Type: 4HEL 3590 Control: Siemens TOUCH Year: 2018 Specifications Metric US Standard Rolling width 3500 mm Rolling thickness 3x toproll Ø 80 mm Rolling thickness 5x toproll Ø 110 mm Rolling thickness prebending 90 mm Top Roll Ø 900 mm Top Roll Ø 900 mm Bottom Roll Ø 800 mm Side roll Ø 600 mm Number of rolls 4 Rolling speed 0-6 Adjustiment lower roll 0-200 mm/min. Adjustment side rolls 0-400 mm/min. Top support yes Side supports yes Number of driven rolls Bdsdpfx Alokvm Nfj Ujg 2 Power 90+75+9 kW Dimensions (Estimate) Length 4430 mm Width 8800 mm Height 11000 mm Weight 178000 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, functionality: fully functional, actuation type: hydraulic, roller (top) diameter: 420 mm, sheet thickness (max.): 25 mm, total length: 3,100 mm, Hydraulic cylinder Brand: Casanova Bending length: 3,100 mm Maximum bending thickness: 25 mm Top roller diameter: 420 mm The side rollers are raised parallel, without inclination. New control and command panel, installed and modified in 2003. Equipped with hydraulic flag and hydraulic side table. Pit dimensions: - 200x6800 mm - 555 mm depth Bdjdpjydk D Hjfx Al Uog

Condition: new, functionality: fully functional, The EVO is the latest innovation in sheet metal processing. It is equipped with numerous innovative and patented features that increase your production capacity and productivity, while offering the lowest total cost of ownership. The high-quality components used in this machine and the latest version of the BENDtronic® control system, which is installed as standard on all EVO machines, are particular highlights. Available from stock: HAEUSLER EVO 31031 4-roll round bending machine / roll bending machine Manufacturer: Haeusler Type: EVO 31031 4-roll round bending machine / roll bending machine Origin: Germany / Switzerland Year of manufacture: 2024 Condition: NEW, exhibition machine Availability: immediately Bdodpfx Aoxwmb Hol Ueg Performance: Working width 3100 mm Round bending capacity 14 mm Bending capacity 12 mm Not the right machine? As a representative of Haeusler, we can put together and offer you your desired machine according to your requirements. Please do not hesitate to contact us.

Year of construction: 2007, condition: good (used), Make: HAEUSLER Type: Clamp Year: 2007 Specifications Metric US Standard Min. shell inner diameter 1800 Max. shell inner diameter 5500 Min. shell outside diameter 1500 Max. shell outside diameter 2500 Minimum wall thickness 10 mm Maximium wall thickness 40 mm Max. section weight 15 T Max. weight total workpiece 60 T Bdjdokwcn Espfx Al Usg Dimensions (Estimate) Length 24000 mm Width 6000 mm Height 3200 mm Weight 0 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), functionality: fully functional, Year of construction: 1990, machine/vehicle number: 4ROLL, roller (bottom) diameter: 470 mm, roller (top) diameter: 470 mm, side roll diameter: 420 mm, roller diameter: 470 mm, roller length: 3,050 mm, working width: 3,050 mm, working height: 1,800 mm, sheet thickness (max.): 50 mm, sheet thickness steel (max.): 45 mm, sheet thickness aluminum (max.): 45 mm, sheet thickness copper (max.): 45 mm, overall weight: 43,000 kg, total length: 7,700 mm, total width: 2,410 mm, total height: 2,470 mm, power: 37 kW (50.31 HP), input voltage: 380 V, type of input current: three-phase, working length: 3,050 mm, Equipment: documentation/manual, emergency stop, PLATE BENDING MACHINE FACCIN - 4 ROLL HYDRAULIC 3000 X 40 MM MODEL 4HCI3-35/30 YEAR 1990 PLATE BENDING ROLL LINEAR GUIDEWAYS DOUBLE PINCH PRE-BENDING Machine in good working condition Bending capacity -Plate width : 3000 mm -Rolling plate thickness 40 mm - Prebend thickness 35 mm Rolls dimensions: -Useful length 3050 mm -central rolls upper/lower 470 mm -side rolls left/right 420 mm • Hardening of the 4 rolls high strength surface • 3 rolls driven powered with gear unit with hydraulic motor • Conical bending attachment side rolls tiltable to form cones, contrast pad roller type. • Opening front hydraulic drop-end to unload the closed shell. • Variable speed working roll bending rotation hydraulic speed fast/slow. • Console electric on wheels with centralized commands joysticks and 3 digital readout. Bodpfx Aowb Scmel Ujdg • Digital readouts of the rolls position bending and pre-bending repeatability. • Hydraulic tank capacity oil 350 liters – power electric 37 Kw voltage 380 /50 • Dimension 7700 x2410 x H 2470 mm - weight 43000kgs

Condition: new, functionality: fully functional, Year of construction: 2026, roller (bottom) diameter: 310 mm, roller (top) diameter: 320 mm, roller diameter: 310 mm, roller length: 1,550 mm, working width: 1,500 mm, sheet thickness steel (max.): 38 mm, overall weight: 12,500 kg, total length: 4,500 mm, total width: 2,300 mm, total height: 1,740 mm, power: 18.39 kW (25.00 HP), working length: 1,500 mm, Equipment: documentation/manual, emergency stop, FACCIN HAV 15342 variable three-roll bending machine Electronically controlled, hydraulic three-roll bending machine Technical data: Number of rollers: Three Geometry of the side rollers: variable Working width: 1550 mm Top roller diameter: 320 mm Side roller diameter: 310 mm Pressure force against the top roller: 160 tons Working pressure at nominal force: 250 bar Guaranteed installed power: 18 kW (25 hp) Guaranteed maximum rotation speed: 3.5-7 m/min Guaranteed machine weight: 12,500 kg Length: 4,500 mm Width: 2,300 mm Height: 1,700 mm Guaranteed performance: Bdedpfx Ast Akt Rjl Usg for material with yield strength 260 N/mm² Rolling capacity (full working width) 38 mm Bending capacity (full working width) 20 mm from pipe diameter 1,600 mm Rolling capacity (full working width) 30 mm Bending capacity (full working width) 17 mm from pipe diameter 415 mm Standard equipment: Variable geometry with linear guides for roller movement Extra long folding bearing for increased frame stability Electronic parallelism system EPS Hardened rollers for high wear protection All rollers ground after heat treatment Siemens S7-HMI PLC control system PGS-CLASSIC control system with Siemens touch panel Hitech hydraulic and electrical package Simultaneous rotation and roller movement Safety ripcord with emergency stop and CE certification Central lubrication Water cooling for the hydraulics Cone bending device Prepared for retrofitting of supports and roller conveyors FACCIN Advantage Package AP

Condition: refurbished (used), BENDING ROLL MACHINE SHEET METAL LENGHT 4000mm SHEET METAL THICKNESS 15mm 3 BENDING ROLLS PREBENDING WEIGHT: 23.000kgr Bsdpfshxyilex Al Uedg THE MACHINE IS IN TOP CONDITION LIKE NEW NEW ELECTRIC PANEL, NEW ELECTRIC CABINET, NEW CABLES, NEW SEALS, MOTOR AND PUMB RESTORATION

Condition: new, Ostas 4-Roll Plate Bending Machine 4R OHS 2570 x 275 Hydraulic Side Roll Positioning 3 Digital Displays Hydraulic Drop-End Hardened Rolls Cone Bending Device Separate Control Console Roll Length: 2570 mm Top Roll Diameter: 275 mm Side Rolls Diameter: 220 mm Total Motor Power: 16.5 kW Weight: 9500 kg Dimensions (mm): 5350 x 1750 x 1950 (L x W x H) Bending Performance Data 16 mm at minimum inside diameter (5 x top roll) 12 mm at minimum inside diameter (1.5 x top roll) Pre-bending Performance Data Bedpfxoxrdn He Al Uedg 12 mm at minimum inside diameter (5 x top roll) 10 mm at minimum inside diameter (1.5 x top roll) All bending capacities are based on 250 N/mm2 yield strength Material (ST 37 – ST 42 structural steel) The images shown are for illustration purposes only.

Year of construction: 1991, condition: good (used), Make: HAEUSLER Type: VRM-HY Year: 1991 Specifications Metric US Standard Rolling width 3000 mm Rolling thickness 3x toproll Ø 120 mm Rolling thickness 5x toproll Ø 150 mm Rolling thickness prebending 100 mm Top Roll Ø 910 + 820 + 740 mm Bottom Roll Ø 940 mm Side roll Ø 780 mm Number of rolls 4 Rolling speed 2 + 4 Adjustiment lower roll 200 mm/min. Adjustment side rolls 500 mm/min. Number of driven rolls 2 Power 300 kW Dimensions (Estimate) Length 8000 mm Width 5400 mm Height 5400 mm Weight 290000 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details! Bdedpfx Alekwcc Nj Ujg Share on

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2017, machine/vehicle number: 25498, roller (bottom) diameter: 320 mm, roller (top) diameter: 320 mm, side roll diameter: 260 mm, working width: 2,070 mm, sheet thickness (max.): 25 mm, TECHNICAL DETAILS Sheet width: 2,070 mm Sheet thickness: 25 mm Bending capacity: 18 mm Top roller diameter: 320 mm Side roller diameter: 260 mm Lower roller diameter: 320 mm MACHINE DETAILS Total power supply: 26 kW Dimensions & Weight Bdjdoygw Ikspfx Al Ujg Space requirement: approx. 4,700 x 2,000 x 2,200 mm Machine weight: approx. 8,100 kg EQUIPMENT Hydraulic lateral roller adjustment Conical bending device 2 driven rollers Hardened rollers Hydraulic drop-end bearing Mobile control panel Foot switch Safety device CE marking

Year of construction: 1980, condition: good (used), Make: HAEUSLER Type: VRM-HY Year: 1980 Specifications Metric US Standard Rolling width 3000 mm Rolling thickness 3x toproll Ø 130 mm Rolling thickness 5x toproll Ø 140 mm Rolling thickness prebending 120 mm Top Roll Ø 950 mm Bottom Roll Ø 850 mm Bjdpfjkvm Szex Al Ujdg Side roll Ø 180 mm Number of rolls 4 Rolling speed 2 + 4 Adjustiment lower roll 0 - 400 mm/min. Adjustment side rolls 0 - 400 mm/min. Number of driven rolls 2 Power 132 + 37 kW Dimensions (Estimate) Length 12000 mm Width 5440 mm Height 5650 mm Weight 286000 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Year of construction: 1978, condition: good (used), Make: HAEUSLER Type: VRM-HY Year: 1978 Specifications Metric US Standard Bdjdpskvm S Njfx Al Ueg Rolling width 3050 mm Rolling thickness 3x toproll Ø 60 mm Rolling thickness 5x toproll Ø 70 mm Rolling thickness prebending 50 mm Top Roll Ø 630 mm Bottom Roll Ø 600 mm Side roll Ø 500 mm Number of rolls 4 Rolling speed 0 - 5 Adjustiment lower roll 200 mm/min. Adjustment side rolls 200 mm/min. Number of driven rolls 2 Power 120 kW Dimensions (Estimate) Length 5790 mm Width 4200 mm Height 4200 mm Weight 85000 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: refurbished (used), BENDING ROLL MACHINE ROUNDO SHEET METAL LENGHT 2500mm SHEET METAL THICKNESS 30/25mm 3 ROLLS Bdjdpfxehx N Uko Al Usg WEIGHT: 19.000kgr

Condition: ready for operation (used), functionality: fully functional, Year of construction: 1980, machine/vehicle number: 4350, roller (bottom) diameter: 280 mm, roller (top) diameter: 300 mm, sheet thickness (max.): 20 mm, overall weight: 14,200 kg, working length: 2,000 mm, TECHNICAL DETAILS Bending length: 2,000 mm Max. sheet thickness: 20 mm Bending capacity: 15/11 mm Bdjdozi D Saspfx Al Ueg Bottom roller diameter: 280 mm Top roller diameter: 300 mm MACHINE DETAILS Drive power, main drive: 16.2 kW Drive power, top roller drive: 4.8 kW Drive power, bottom roller drive: 3.7 kW Weight: 14,200 kg

Condition: new, functionality: fully functional, Year of construction: 2026, FACCIN 4HEP 3163 Four roll bending machine Electronically controlled, hydraulic four-rolls bending machine Technical specifications: Number of Rolls: Four Geometry of the side rollers: planetary guide Working length: 3000 mm Top roll diameter: 630 mm Lower roll diameter: 570 mm Side rolls diameter: 500 mm Guaranteed installed power: 72 kW Guaranteed maximum rotation speed: 5 m/min Guaranteed machine weight: 58,000 kg Length: 6,800mm Width: 3,600mm Bdedpfoiivfqjx Al Ueg Height: 3,550mm Guaranteed capacities: for material with a yield point of 260 N/mm² Rolling capacity (full working width) 70 mm Bending performance (full working width) 60 mm from pipe diameter 3150 mm Rolling capacity (full working width) 55 mm Bending capacity (full working width) 50 mm from pipe diameter 820 mm Standard equipment: Planetary movement of the side rolls Extra heavy double hinged folding release Electronic parallelism system EPS Hardened rolls for high wear protection cone bending device Mobile control panel 3 digital displays for the position of the side rolls and the lower roll Safety trip wire with emergency stop and CE certification

Condition: new, functionality: fully functional, Year of construction: 2026, FACCIN 4HEP 3135 Four roll bending machine Electronically controlled, hydraulic four-rolls bending machine Technical specifications: Number of Rolls: Four Geometry of the side rolls: planetary guide Working length: 3000 mm Top roll diameter: 350 mm Lower roll diameter: 330 mm Side rolls diameter: 250 mm Guaranteed installed power: 14.4 kW Guaranteed maximum rotation speed: 5 m/min Guaranteed machine weight: 13,000 kg Length: 5,700mm Width: 1,800mm Height: 2,100mm Guaranteed capacities: for material with a yield point of 260 N/mm² Rolling capacity (full working width) 20 mm Bending performance (full working width) 15 mm from pipe diameter 1750 mm Rolling capacity (full working width) 14mm Bending capacity (full working width) 12mm from pipe diameter 455 mm Standard equipment: planetary movement of the side rollers Bodpfxoiivc Do Al Uedg Extra heavy double hinged folding release Electronic parallelism system EPS Hardened rolls for high wear protection cone bending device Mobile control panel 3 digital displays for the position of the side rolls and the lower roll Safety trip wire with emergency stop and CE certification

Condition: new, functionality: fully functional, Year of construction: 2026, FACCIN 4HEP S54 Four roll bending machine Electronically controlled, electric drive, four-rolls bending machine Technical specifications: Number of Rolls: Four Geometry of the side rolls: planetary guide Working length: 3000 mm Top roll diameter: 300 mm lower roll diameter: 280 mm Side rolls diameter: 200 mm Guaranteed installed power: 10.8 kW Guaranteed maximum rolling speed: 5 m/min Guaranteed machine weight: 10,000 kg Length: 5,500mm Width: 1,400mm Height: 1,600mm Guaranteed services: for material with a yield point of 260 N/mm² Rolling capacity (full working width) 18 mm Bending performance (full working width) 12 mm from pipe diameter 1500 mm Rolling capacity (full working width) 12 mm Bending capacity (full working width) 10 mm from pipe diameter 450 mm Standard equipment: Electrical drive of the top roll Planetary movement of the side rolls Extra heavy double hinged folding release Electronic parallelism system EPS Bdsdpeiivgrefx Al Usg Hardened rollers for high wear protection cone bending device Mobile control panel 3 digital displays for the position of the side rolls and the lower roll Safety trip wire with emergency stop and CE certification

Condition: new, functionality: fully functional, Year of construction: 2026, FACCIN HAV 3162 variable three-rolls bending machine Electronically controlled, hydraulic three-rolls bending machine Technical specifications: Number of Rolls: Three Geometry of the side rolls: variable Working length: 3050 mm Top roll diameter: 620 mm Side rolls diameter: 550 mm Pressure force against the top roll: 630 tons Working pressure at nominal force: 250 bar Guaranteed installed power: 55 kW (75 hp) Guaranteed maximum rotation speed: 3.5-7 m/min Guaranteed machine weight: 45,000 kg Length: 7,600mm Width: 3,700mm Height: 3,100mm Guaranteed capacities: for material with a yield point of 260 N/mm² Rolling capacity (full working width) 75 mm Bending performance (full working width) 48 mm from a pipe diameter of 3,100 mm Rolling capacity (full working width) 55 mm Bending performance (full working width) 40 mm from pipe diameter 805 mm Standard equipment: variable geometry with linear guides for rolls movement Extra long release arm for increased frame stability Electronic parallelism system EPS Hardened rolls for high wear protection All rolls ground after heat treatment Siemens S7-HMI PLC control Bedpjiivgysfx Al Uedg PGS-CLASSIC control with Siemens touch panel Hitech hydraulic and electric package Simultaneous rotation and rolls movement Safety trip wire with emergency stop and CE certification central lubrication Water cooling for the hydraulics cone bending device Prepared for retrofitting supports and roller conveyors FACCIN Advantage Package AP

Year of construction: 1985, condition: used, machine/vehicle number: 112-176, Technical specifications: Bedpfx Aloc I Snzs Ujdg - Bending process controlled by automatic or manual operation. - Bending capacity for square steel ST 37 up to approx. 25 mm. - Bending capacity for flat steel ST 37 up to approx. 30 x 8 mm. - Adjustable bending length between the rotating units up to approx. 1000 mm. - Clamping plate with various mounting holes for different profiles. - Tailstock / backstop. - Preselection of bending time / preselection of bending length and rotation angle. - Right-hand / left-hand operation. - Space requirement: approx. W 1750 x H 1100 x D 500 mm. - Drive: 400 V / 0.75 kW. - Weight: approx. 150 kg.

Condition: new, neu ca. 10 Wochen ab Auftrags Türkei 53700 € 1014.93 € 2050 mm 16 mm 16 mm 13 mm 13 mm 10 mm 260 mm 260 mm 200 mm 1,5 / 6 m/min 7.5 kW 4300 mm 1600 mm 1550 mm 6100 kg 4 rolls Top rolll driven by hydromotor and planetary gearbox, bottom roll driven by gear and cardan system Pinch roll and latereal rolls move with hydraulic cylinders Digital read-out for lower and side rolls position Hardened rolls Conical bending device Hydraulic load relieving of upper roll Hydraulic drop-end bearing 2 working speeds Protectionagainst overload Moveable control pane According to CE rules Bodpfx Aleynm Eho Ujdg OPTIONAL EQUIPMENT: Infinitely adustable speed of rolls Hydraulic side support Hydraulic top support NC control IMPORTANT ISSUES AT CONICAL BENDING: The max. sheet metal thickness isequivalent to 50 % of nominal capacity The cone length can be max. 30 % oremust be more than 60 % of roll length Hardened rolls are recommended

Condition: new, neu ca. 12 Wochen ab Auftrags Türkei 73200 € 1383.48 € 2050 mm 20 mm 20 mm 16 mm 16 mm 12 mm 280 mm 280 mm 220 mm 1,5 / 5 m/min 16.5 kW 4350 mm 1700 mm 1850 mm 8550 kg 4 rolls fullhydraulic drive of upper roll and lower roll hydraulic infeed of lower and side roll digital read-out of lower and side rolls position hardened rolls conical bending device hydraulic load relieving of upper roll hydraulic drop-end bearing 2 working speeds central lubrication system protectionagainst overload moveable control pane according to CE rules OPTIONAL EQUIPMENT (PRICES ON REQUEST): Bdjdpfxeynmyls Al Usg infinitely adustable speed of rolls hydraulic side support hydraulic top support NC control IMPORTANT ISSUES AT CONICAL BENDING: the max. sheet metal thickness isequivalent to 50 % of nominal capacity the cone length can be max. 30 % oremust be more than 60 % of roll length hardened rolls are recommended

Condition: new, functionality: fully functional, Year of construction: 2026, TECHNICAL SPECIFICATIONS: Bdedpfx Aljgd T R Dj Uog Number of rolls FOUR Geometry linear guides Maximum plate width mm 3000 Top roll diameter mm 390 Bottom roll diameter mm 370 Side rolls diameter mm 295 Installed power HP 40 Stepless variable rotation movement m/1' 4-8 Machine weight (guaranteed) Kg 19,000 Guaranteed performance with material yield point 260 N/mm² Rolling capacity (full working width) Ø 1950 mm 25 mm Bending performance (full working width) Ø 1950 mm 20 mm Rolling capacity (full working width) Ø 507 mm 18 mm Bending performance (full working width) Ø 507 mm 16 mm • Hardened and polished rollers • Siemens NC control • Cone bending device with electronic tilting

Condition: new, functionality: fully functional, Year of construction: 2026, HAV 3293 Plate width: 3200mm Top Roll diameter: 930mm Bdsdpfxeiivg Sj Al Usg Side rolls diameter: mm 800 Machine weight: 150 Ton Rolling capacities (Y:260Mpa/Ø 4650mm): 3200mmx155mm Prebending capacities (Y:260Mpa/Ø 4650mm): 3200mmx115mm

Condition: new, functionality: fully functional, Year of construction: 2026, BIKO B4 2014 Linear Four roll bending machine Hydraulically controlled four-rolls bending machine Make BIKO, model B4 2014 Technical specifications: Number of Rolls: Four Geometry of the side rollers: linear guides Working width: 2000 mm Top roller diameter: 145 mm Lower roller diameter: 130 mm Side roller diameter: 130 mm Guaranteed installed power: 5.5 kW Guaranteed maximum rotation speed: 5 m/min Guaranteed machine weight: 2,300 kg Length: 2,900mm Width: 900mm Height: 1,000mm Guaranteed capacities: for material with a yield point of 260 N/mm² Rolling capacity (full working width) 4 mm Bending performance (full working width) 3 mm from pipe diameter 725 mm Rolling capacity (full working width) 3 mm Bending performance (full working width) 2 mm from pipe diameter 190 mm Standard equipment: Bjdpfx Ajiinknsl Usdg Linear guide system for rolls movement Extremely wide bearing blocks Needle bearing for the rolls rotation Extra heavy double hinged folding release Hardened rolls for high wear protection Hydraulic parallelism system of the side rolls Digital display for the position of the side rolls and the bottom roll cone bending device Control on the swiveling control panel Safety trip wire with emergency stop and CE certification