Used Coating Line for sale (11,433)

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 5,600 mm, total length: 11,200 mm, total width: 5,100 mm, type of input current: three-phase, warranty duration: 24 months, inner dimension height: 4,970 mm, inner dimension length: 11,000 mm, temperature: 80 °C, inner dimension width: 5,000 mm, air demand: 52,000 m³/h, input voltage: 380 V, heating capacity: 250 kW (339.91 HP), power: 45 kW (61.18 HP), fuel: liquid petroleum gas (LPG), input frequency: 50 Hz, energy consumption: 45 kWh, insulation thickness: 50 mm, nominal power: 250 kW (339.91 HP), sheet thickness steel (max.): 2 mm, Equipment: lighting, * Air Preparation Unit: The air preparation unit is a recirculation system that supplies the cabin with filtered fresh air and exhausts used air during the painting process. It heats the air to 60 °C, mixes the used air with 10% fresh air via an automatic multi-damper system, and reheats the air before routing it back into the cabin. The air is heated using a burner and a heat exchanger, both made of high-quality 304 stainless steel and housed within the fresh air unit. During painting, the air is filtered twice (via front and ceiling filters) before it enters the cabin. The contaminated air is also filtered twice (through inlet and outlet filters) before it exits via the exhaust unit. Air preparation units are insulated like the side walls to minimize heat loss and are protected against potential vibration and noise thanks to rubber seals on the covers. The exhaust air is regulated by a damper in the outlet duct, which helps control the internal pressure of the cabin. * PRINCIPLES OF CABIN OPERATION: The processes in the cabin are controlled via a control panel that manages the following steps: * PAINTING PROCESS: Fodswzl Hxepfx Aa Esfw During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled by the extraction unit. Floor filters (paint stops) capture paint particles, and the air passes through the final exhaust filters before being discharged. * FLASH-OFF PROCESS: After painting, the cabin operates for approximately 15 more minutes to purge residual solvents and thinners. During this phase, fresh air from outside continues to circulate in the cabin. * DRYING PROCESS: In this phase, 80% of the air passing through the cabin is heated to 60 °C and supplied to the cabin via a distributor. As 20% of the solvent is released during drying, these solvents are expelled with the exhaust air. Industrial coatings are typically dried at 60 °C, but the cabin temperature can be adjusted via the control panel as required. * COOLING PROCESS: After the 30-minute drying process, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the 5-minute cooling phase, fresh air from outside circulates in the cabin, after which the system stops automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT: These control panels manage the functions and operation of all machinery and devices inside the cabin. The control panel is constructed from durable galvanized sheet metal and steel profiles and is fully enclosed to protect against dust and moisture. Electrical devices and control panels: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control lines between the panel and motors or other electrical devices. • Electrical wiring is designed to allow for cabin relocation if necessary. • Operating devices use 380 V 50 Hz, while control devices use 220 V.

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: PEF-2.5 PULVER EINBRENNOFEN ELEKTRISCH, temperature: 230 °C, heating capacity: 30 kW (40.79 HP), inner dimension length: 2,500 mm, inner dimension width: 1,505 mm, ✈️ Plus shipping costs – Shipping available upon request.✈️ Fast delivery: Only 6 weeks after receipt of payment! ✅✅✅Energy Class A+++✅✅✅ ✅ Plug & Play system – Delivered fully assembled, ready to use immediately! ✳️ Maintain your liquidity! We offer a variety of financing options to ensure your investment has the best chance of success. Contact us today to learn more about our hire purchase, warranty, or leasing programs. ☘️Environmentally friendly☘️⚡️Green energy⚡️☘️ ⭐ Powder furnace with electric heating - ✔️ Internal dimensions: 2500 mm L * 1505 mm W * 1800 mm H ✔️ Electric heating output: 30 kW/h ✔️ Fan: 3000 m3/h 80 mm SS ✔️ Circulation fan output: 1.5 kW/h ✔️ Total 35 kW/h +- 10% ✔️ Digital heat control, continuously adjustable temperature up to 220°C ✔️ Sandwich panels inside: 1.5 mm galvanized steel, outside: 1.5 mm powder-coated Steel ✔️ Adjustable curing temperature, curing time, and exhaust fan function ✔️ An audible signal sounds at the end of the curing time ✔️ Insulated door with special locking systems (snap lock) ✔️ Insulation: 150 mm (150 mm rock wool) 🔥 PEF-2.5 Curing Oven: Your versatile industrial oven for drying and curing processes! 🔥 Whether powder coating, wet paint, plastic processing, or other thermal processes – the powder curing oven is your reliable solution for professional curing and drying processes up to 230°C! 🌡️ _____ 🚚 Maximum loading flexibility • Compatible with ceiling rail systems • Optionally with insert shelf system for small batches _____ ⚙️ Intelligent control – just the way you need it ✅ PID control (optional) for precise temperature control ✅ Touchscreen control panel & smartphone control 📱 (optional) ✅ Weekly & monthly reports at the touch of a button (optional) ✅ Timer function: freely programmable from 10 minutes to 24 hours ⏲️ ✅ Automatic shutdown after the end of the process _____ ♨️ Ramp heating mode (optional) Precisely control temperature progression and holding times, e.g. E.g.: • Reach target temperature within a defined time • Maintain desired time • Controlled cooling to target temperature • Automatic notifications of process events _____ 🛡️ Safety is our priority 🟢 Safety sensors to prevent overheating 🟢 Automatic shutdown in the event of a fault 🟢 Acoustic warning signals in the event of errors 🟢 Solvent and fume removal via automatic venting _____ ⚡ Customized energy and heating system 🔥 Also available with an extension up to 400°C for high-temperature processes (optional) _____ 🧠 No repeated settings necessary! The furnace saves your process parameters – batch by batch. This saves you time and avoids errors. _____ 📢 And best of all: If you have special requirements – we also build customized furnaces according to your specifications! Contact our team of experts for a personalized consultation! _____ ☀️ 2-YEAR WARRANTY ☀️ Ffsdpfxowfgbrj Aa Eew Request more information

Condition: excellent (used), ELOPAK SHIKOKU ASEPTIC FILLING LINE Fodpfxoxdbwio Aa Eefw Model S-PS80HA YOM 2008 Working hours - 9,000 hours. Line capacity for 3 streams - 8100 pcs./h, for two 7100 pcs./h for one 6000 pcs./h Carton format: 500ml, 750ml, 1000ml The line includes: - Elopak filler S-PS80HA for Pure Pak classic packaging material - 3 units of PURE-PACK PLA-S30 cap applicators for Pure-Twist 2U cap - WA-Flex-30 packer - Conveyor system. - Conveyor lubrication station. - Spare parts a total of 4,000 dollars.

Condition: new, Year of construction: 2025, We produce pellet-briquette line We are the only manufacturers in Lithuania, the only ones with our own service. We will deliver, install, set up and train the lines. We select a package according to your budget. We not only produce the equipment ourselves, but we also produce pellets ourselves, you can come and see the working equipment. Pellet production lines from 100 kg/h to 30 t/h We produce: Drum dryer Belt dryer pipe dryer Pellet plant Mills crushers Conveyor Coolers Cyclones Bunker Packing machines TSF-Justinas Fedpfx Aaehgbars Esfw

Condition: like new (used), Year of construction: 2014, Complete Bottle Filling Line for non-aseptic milk and other dairy product Capability 250, 500, 1000 ml PET/Plastic bottles with the cap D- 38 mm Ffjdpfx Aaeyiptqe Ejw Made by SELO, Netherlands. Consisting of: 1. 2x Accumulation Tables 150 cm diameter Motorised 2. Rotary Bottle Washer 15 bottle capacity Siemens Logo TD touch screen With Associated Conveyor 3. Selo 6 Head Filling Machine 6 head fully automated filling station With Selo pressure tank Schneider touch screen control Pump and associated pipework 4. Capper Rotary 3 Head fully automated bottle capper with Mobile Cap Hopper/ Swan Neck cap Feeder 5. Albertina/Etipak In Line Labeller 6. Associated conveyors AS NEW CONDITION

Condition: new, Year of construction: 2024, functionality: fully functional, ⚡️ Top Service ⚡️ Fast Delivery ⚡️ Excellent Support! ✈️ Price includes shipping within Germany – No additional transport costs! ✈️ Fast delivery: Only 6 weeks after receipt of payment! PROFESSIONAL POWDER COATING HAS NEVER BEEN THIS EASY! Looking to expand your business and enter the world of professional powder coating? The PEF2.5+ is the perfect solution for beginners! This high-performance system allows efficient, cost-effective, and high-quality coating of car rims and smaller workpieces – with minimal effort! ✨UNBEATABLE PROMOTION – ONLY UNTIL THE END OF MAY!✨ Take advantage of this limited-time offer before it's too late! Fjdpfx Aaowfhu Hj Eofw PONY Luxury Coating – QUALITY THAT CONVINCES! ✅ Plug & Play system – Delivered fully assembled, ready to use immediately! ✅ 100% European manufacturing – No China products, only top quality built to European standards! ✅ Modular & expandable – Additional options for greater performance and flexibility! ✅ All spare parts included – Long-term use with no hidden extra costs! ✳️Maintain your liquidity! We offer a variety of financing options to ensure your investment has the best chance of success. Contact us today. ✳️ ✨✨Buy directly from the manufacturer and secure price and quality advantages!✨✨ ☘️Environmentally friendly☘️⚡️Green Energy⚡️☘️ Powder oven + powder booth + powder gun Complete Starter Package PEF2.5+ ⭐ Powder oven with electric heating ✔️ INTERNAL WIDTH: 1,505mm ✔️ HEIGHT: 1,800mm (from air duct) ✔️ INTERNAL LENGTH: 2,500mm ✔️ Thermoblock unit dimensions: 785x1800x2210mm; heating capacity is 30 kW/h; recirculation fan is 1.5kW/h – 1 pc.; exhaust fan is 0.54kW/h. ✔️ Double-wing door with thermal insulation and silicone seal. ✔️ Guide rails for rack trolleys are manufactured according to the dimensions specified on the base plates. ✔️ Specially designed air duct for homogeneous air distribution inside the curing oven. ✔️ Electrical panel materials by Siemens and Schneider. This curing oven does not include a PLC system. PLC is available as an option. ✔️ Curing temperature, curing time, and heater unit function are adjustable. At the end of the program, an alarm and light signal from the buzzer will indicate completion. ✔️ Additionally, a product transport trolley with cast wheels is located inside the oven. ⭐ Powder coating booth ✔️ Dimensions: 800x1930x2200mm (including fan) ✔️ Teflon filters: 4 pcs. ➢ Filter suction fan: 4kW x 1 pc. (6,000m3/h – 200mmSS) ✔️ 36W LED lighting x 1 pc. ✔️ Bottom drawer x 1 pc. ✔️ Control panel for air intake and powder spray regulation ✔️ DELTA frequency converter ✔️ Heavy-duty rollers under the coating booth ✔️ Additional filter at the fan outlet ⭐ Powder coating gun E-Coat+3 Master with Multicolor (vibration table) Enquire now – Get your business ready for the future! ☀️ 2-YEAR WARRANTY ☀️ ☀️All our machines are CE-certified and necessary machines have ATEX certificates.☀️

Condition: used, Year of construction: 1990, Manufacturer: SALICO S.P.A. Year: 1990 Thicknesses: 3-13.5mm Coil capacity: 25t Coil width:320-1250mm Fedpfxeurlaks Aa Ejfw Direction: Left-Right Sizes of line: 17x13m Maximum external diameter: 2000mm Minimum external diameter: 700mm Minimum internal hole of coil:500mm Maximum internal hole of coils: 600mm Knife diameters: Max 460, Min 410mm Absolute number of cuts 15 Number of cuts with maximum thcikness 13.5mm: 3 cuts for hard material, 5 cuts for mild material.

Condition: like new (used), Range (in depending on the lighting conditions) until: 15 m Range with laser receiver: 30 m, & more 5 m: leveling accuracy +/-1 mm Self leveling range: 4° +-0,5 ° Accuracy of the horizontal line at 5 m: +-1.5 mm Fsdpsd Ecncefx Aa Esfw Accuracy of vertical line at 3 m +-0.75 mm Number of laser lines: 2 Weight: 485 g

Year of construction: 2006, condition: ready for operation (used), functionality: fully functional, Rondo Doge Bread & Pastry Line. Year of production 2006. Total length 16.7m (Machine 11.55m + tables 5.15m) Ffsdpfx Aown Hhqsa Ejw Width 1.80m (working width 0.7m) Height to hopper 3m. Total height 4.05m Efficiency: 600kg per hour - from 2500 pcs to 7500 pcs of products per hour for square, triangular and flat products Ability to produce a very thin continuous line of dough - from 1 mm to 24.5 mm. - Dough portioning hopper - 3 sprinklers - 2-roll dough extruder - calibrator - satellite sheeter - flour sprinkler - cross roller - longitudinal plate assembly - dough folders - pneumatic guillotine Machine connected to the power supply and ready to work.

Condition: used, Year of construction: 1990, Heavy-duty rollforming line 10 stations Ffjdpfx Aeymzzusa Esw Width: 260 mm

Condition: used, Year of construction: 1990, HEAVY DUTY ROLLFORMING LINE Fodpeymzywefx Aa Eefw 11 STATIONS WIDTH: 450 mm

Condition: used, Year of construction: 1990, HEAVY DUTY ROLL FORMING LINE 9 STATIONS WIDTH: 450 mm Ffsdpfx Aoymzxyoa Eew

Condition: used, Year of construction: 2006, functionality: fully functional, NP 690 - COMPLETE GLASS BOTTLING LINE SIDEL 46,000 bph Product: Mineral Water Speed: 46,000 bph Depalletizer Simonazzi Model: SWEEP-OFF-B Year: 2005 Type: with layer separator Interlayer removal system Pallet storage Saturator Simonazzi Model: CARBOGEA Year: 2005 Speed: 9,800 lph Filling Monoblock Simonazzi Model: EUROSTAR 2000 Year: 2005 Rinser: 84 clamps, fixed nozzle, treated product: water Filler: 84 valves, isobaric filling, mechanical valves 2 Cappers: - 24-head crown cap Ø 26 mm - 24-head aluminum screw cap Bottle Inspector Heuft Model: HBBVXTXXX Year: 2011 Fodpfx Aajyc Rw De Esfw Level and cap integrity check Labeller Simonazzi Model: ALFA TOP BRAIN Year: 2005 32 heads, 3 cold glue stations Applicable label types: • Front • Back • Neck/collar Label Inspector ABULL Model: STRATEC - F300 Year: 2005 Shrink Wrapper SMI Model: SK800F Year: 2005 Version: film only Type: film only Double-lane for 3x2 bundles Shrink Wrapper SMI Model: SK600P Year: 2005 Version: film with tray Types: film and tray 20/24 pcs (4x6) Palletizer Simonazzi Model: KOMBI Year: 2005 Type: push-type palletizer Interlayer system Pallet storage Pallet Wrapper ROBOPAC Model: ROTARY Year: 2005 Wrapping type: rotating arm Bottle conveyor belts Bundle conveyor belts

Condition: new, Year of construction: 2025, total height: 982 mm, total length: 4,000 mm, total width: 1,100 mm, volume flow: 18,000 m³/h, warranty duration: 12 months, Extraction wall with 18,000 m3/h Max. power consumption 5 kW/h Electric motor 4 kW Air unit 18,000 m3/h Nicotra ADH 400 Fedpfx Aaswz Ic Nj Ejfw The full description can be found in the attachment to this listing.

Condition: new, Powder Coating Systems Fjdpfjxa Hzxsx Aa Eofw For years, powder coating has been continuously evolving as an alternative to wet painting, and it has recently gained increasing importance due to its lower environmental impact—specifically the absence of solvents and paint sludge. Powder recovery further boosts the efficiency of these systems to a particularly high level. For users, powder coating offers the advantage of creating an extremely durable and corrosion-resistant surface that is significantly more impact-resistant than what traditional painting can achieve. Additionally, post-processing tasks such as grinding or drilling the powder-coated parts present no problems, as the coating will not chip off. Pony Luxury Coating powder coating systems provide you with tangible advantages: they are efficient, environmentally friendly, and—as always—unsurpassed in flexibility. We achieve this through a range of system types. Manual Powder Coating Systems Manual coating systems are the ideal solution for complex and demanding workpieces. Thanks to skilled operators, these systems offer continuous adaptation to changing conditions and varying product sizes. Flexibility is paramount—with the added benefit of an attractive entry price into the world of powder coating. Large-Scale Powder Spray Booths No matter how large or challenging your workpieces, our systems are larger! In the commercial vehicle and utility sector, where components are exposed to significant stress, powder coating has established itself as the ideal solution. To accommodate ever-larger components, we offer our large-scale powder booth, which supports unlimited manual coating, and, when combined with a conveyor system, handles any workpiece size with ease. Automatic Powder Coating Systems If your operation requires high throughput and rapid processing, an automated powder system is the way forward. Coupled with a conveyor, light barriers allow precise detection and, consequently, exact powder dosage to ensure maximum efficiency. The system can also be equipped with lifting stations and robots to handle even the most complex components. Powder Curing Ovens & Flash-Off Dryers These provide the perfect finishing touch to powder coating: the curing oven. Our ovens feature the highest insulation class, ensuring consistent, high efficiency. Detailed temperature control also enables use as a flash-off dryer to dry substrates after pre-treatment. Temperatures up to 250 degrees Celsius are possible, which allows usage as a tempering oven, for instance with hot-dip galvanized materials. Of course, typical use as a powder curing oven is straightforward. Optimal air distribution and a visualized control panel prevent over-baking, and even allow multiple color shades to be cured in a single process. Do you have questions or suggestions? We are happy to assist you!

Condition: new, Equipment: cabin, Stationary small parts spray booth Dixi █████ Achieve perfect and uniform coating of small parts. The extraction system ensures optimal results even in the smallest spaces. Optionally equipped with a turntable or a wheel holder, as well as a compact yet powerful extraction unit, it is perfectly suited for processing small workpieces and wheels. The side panels effectively limit the distribution of overspray, allowing work to be carried out in confined spaces without contaminating surrounding areas. Ffjdpfexa Hx Rsx Aa Ejw Integrated lighting is also available as an option. Additionally, thanks to its low weight and minimal connections, the booth can be relocated to a new site in no time, ensuring your flexibility at all times. The system comes fully pre-assembled and ready for immediate use. Your Benefits Thanks to its compact design, flexible dimensions, and versatile accessories, this booth offers a broad range of applications. The sophisticated modular system requires minimal space and is therefore suitable for use in virtually any premises. Different filter media and stages enable highly efficient operation, while filter changes can be performed in just a few minutes. Application and Safety Processing of both water-based and solvent-based coating materials is enabled by the use of ATEX-certified explosion-proof motors. It can also optionally be used for spraying adhesives. The large filter surface ensures uniform extraction throughout the process.

Condition: new, Year of construction: 2024, functionality: fully functional, total length: 3,400 mm, total height: 2,210 mm, total width: 1,505 mm, type of input current: three-phase, warranty duration: 24 months, temperature: 250 °C, heating capacity: 30 kW (40.79 HP), inner dimension length: 2,500 mm, Equipment: emergency stop, ✈️ Plus shipping costs – Shipping available upon request.✈️ Fast delivery: Only 6 weeks after receipt of payment! ✅✅✅Energy Class A+++✅✅✅ ✅ Plug & Play system – Delivered fully assembled, ready to use immediately! ✳️ Maintain your liquidity! We offer a variety of financing options to ensure your investment has the best chance of success. Contact us today to learn more about our hire purchase, warranty, or leasing programs. ☘️Environmentally friendly☘️⚡️Green energy⚡️☘️ PEF-2.5 ELECTRIC POWDER FIRING OVEN WIDTH (INTERIOR): 1,505 mm HEIGHT: 1,800 mm (from the air duct) LENGTH (INTERIOR): 2,500 mm ➢ The thermoblock unit measures 785 x 1,800 x 2,210 mm. The heating capacity is 30 kW/h. A circulating fan is 1.5 kW/h (1 pc.), and an exhaust fan is 0.54 kW/h. ➢ Double-leaf door with thermal insulation and silicone seal. ➢ Guide rails are manufactured for trolleys in the dimensions indicated on the floor panels. ➢ Specially designed air duct ensures uniform air distribution in the curing oven. ➢ The electrical switchgear is made of Siemens and Schineider. This curing oven does not have a PLC system. PLC is available as an option. ➢ Curing temperature, curing time, and heating unit function are adjustable. At the end of the program, an audible and light signal is emitted by the buzzer. ➢ Fodpewdtfujfx Aa Eofw Additionally, a product transport cart with cast wheels is located inside the oven. 2. PKF-4 POWDER COATING BOOTH ➢ DIMENSIONS: 800x1930x2200mm (dimensions including fan) ➢ Teflon filters: 4 pcs. ➢ Filter suction fans: 4 kW x 1 pc. (6,000 m3/h – 200 mm SS) ➢ 36 W LED lighting x 1 pc. ➢ Bottom drawer x 1 pc. ➢ Control panel for controlling air intake and pressure blasting ➢ DELTA frequency converter ➢ Heavy-duty rollers under the paint booth. ➢ An additional filter is located at the fan outlet. ♨️ Ramp heating mode (optional) Precisely control temperature progression and dwell times, e.g. E.g.: • Reach target temperature within a defined time • Maintain desired time • Controlled cooling to target temperature • Automatic notifications of process events _____ 🛡️ Safety is our priority 🟢 Safety sensors to prevent overheating 🟢 Automatic shutdown in the event of a fault 🟢 Acoustic warning signals in the event of errors 🟢 Solvent and fume removal via automatic venting _____ ⚡ Customized energy and heating system 🔥 Also available with an extension up to 400°C for high-temperature processes (optional) _____ 🧠 No repeated settings necessary! The furnace saves your process parameters – batch by batch. This saves you time and avoids errors. _____ 📢 And best of all: If you have special requirements – we also build customized furnaces according to your specifications! Contact our team of experts for a personalized consultation! _____ ☀️ 2-YEAR WARRANTY ☀️ Request more information

Condition: like new (used), functionality: fully functional, Year of construction: 2014, operating hours: 24 h, I am selling full complete onion peeling processing line with M&P onion peelers, items are listed below: -6x M & P onion peeler machine -all conveyers, elevators for transport peeled, unpeeled and waste product -inspection table Ffsdpfx Aaetzmifj Eow -all working platforms -all hoppers for row (unpeeled materials) Excluded air screw compressors but for serious enquire i could help out with additional equipment. Capacity 2700- 4500 kg /h of peeled onion

Condition: like new (used), functionality: fully functional, Year of construction: 2014, operating hours: 24 h, I am selling full complete onion peeling processing line with M&P onion peelers, items are listed below: -6x M & P onion peeler machine -all conveyers, elevators for transport peeled, unpeeled and waste product -inspection table Ffodsrrglyepfx Aa Eew -all working platforms -all hoppers for row (unpeeled materials) Excluded air screw compressors but for serious enquire i could help out with additional equipment. Capacity 2700- 4500 kg /h of peeled onion

Condition: excellent (used), Year of construction: 2018, Upgraded Stork / Marel AMF Filleting Line – AMF-i Version We are pleased to offer for sale an upgraded Stork/Marel AMF filleting line, rebuilt from AMF PLC to AMF-i version. The line is in very good technical condition, equipped with its original electric cabinet, and ready to operate in a modern poultry processing plant. The line consists of the following modules: Fjdpfxsx Hymdj Aa Eefw -Filleting line with measuring equipment (encoder) -Loading Module -Deskinner Module -WB without rebuild (no size selection) -Halving with auto adjust -Separating Module -Breast Tendon Harvesting Max speed: 60 fillets/min Year of production: 2018 Condition: Very good

Condition: used, Year of construction: 1996, Manufacturer: Bogma Model: M75 Year of manufacture: 1996 Capacity: 2700 - 3600 kg/h Complete briquette line. - Mooving flor - Screw conveyor - Screw conveyor - Screw conveyor - Feeding system for Bogama 2pc - Three Bogma (briquette press) Fedpfxeh A S Ere Aa Ejfw - One Bogma for spereparts - Pipes for ready briquettes - All hydraulic - All electric, control - Walking platforms etc

Condition: used, Year of construction: 2017, NP 683 | USED KHS CAN FILLING LINE 25,000 CPH Capacity: 25,000 cans per hour Products: Beer and carbonated soft drinks Ffodpoxd Ap Hofx Aa Eow Can format: 500 ml; 211/202 Year of manufacture: 2012, 2017 Current condition: Still installed – machine powered. Can be inspected in dry cycle. Available for dismantling: November 2025 Packaging: Cans will be packed in trays with shrink film. Line components: - Bulk can depalletizer: Linker DPG-500, year: 2012 - Can inspector: Transtech Hysek, year: 2012 - Can conveyor: Linker Conveyor RC/KHS, year: 2012 - Rinser: Linker Triplex Rinser TR/KHS, year: 2012 - Flash pasteurizer: KHS Innopro 140/14/85, year: 2012 - Filler: KHS Innofill Can DVD, year: 2017 - Seamer: Ferrum F08, year: 2012 - Lid feeder: NSM Lidserver A30, year: 2017 - Conveyor: KHS Innoline BTR, year: 2012 - Fill height inspector: KHS Innocheck CUB, year: 2012 - Blower: Europool - Tray packer: KHS Kisters SP0502, year: 2012 - Tray pack conveyor: KHS Innoline GTR, year: 2012 - Handle applicator: KHS CSM 050-2, year: 2012 - Packing machine: KHS Innopack 035 B2+FS A-L, year: 2012/2017 - Palletizer: KHS Innopal PBL1N1, year: 2012 - Pallet stretch wrapper: SIAT MFP, year: 2017 - Pallet conveyor: KHS Innoline PTR

Condition: used, Year of construction: 2013, Bottling Filling Line for Oil PET Year: 1995 | 2013 Speed: 6,000 bph on 1 L Cap: 29/21 mm Preform feeder Compressor for chiller moulds MTA Nr.1 Blower Kosme KSB 3000 Nr.2 Blower Kosme KSB 3000 Air conveyors Kosme Fodpfx Ajq Ttuqsa Ejfw Filling/capping monoblock ICS – 6,000 L/h Labeller ICS cold glue Shrink wrapper SMIPACK Shrink pallet wrapper Zlatorog KAESER high-pressure compressor Code: NP 537

Condition: like new (used), Year of construction: 2004, functionality: fully functional, COMPLETE ASEPTIC TETRA PAK TBA LINE Year: 2004 Ffedpfxjv Ay Uuj Aa Eew Output speed: 8,000 packs/hour Filling machine: Tetra Pak model TBA/21 TPA 500 SO Packaging type: Tetra Brik Aseptic (TBA) Format: 500 ml Prisma Speed: up to 8,000 packs/hour Aseptic filling technology: Hydrogen peroxide sterilization Packaging material feed: Roll-fed carton Touchscreen operator panel Cap applicator: Tetra Pak model TETRA PAK APPLICATOR 45 Cap type: TwistCap or LightCap Cap application: Fully automated Hot melt glue system: Nordson Problue 4 Cap elevator: Tecno Vibrazioni Packing unit: Tetra Pak model TETRA CARDBOARD PACKER 70 Secondary packaging: Tray or box packing Hot melt glue system: Nordson Problue 10 Inkjet coder: Videojet Coding type: Expiry dates, lot numbers Conveyor system: Total length approx. 65 meters

Condition: used, Year of construction: 2010, functionality: fully functional, NP 687 | COMPLETE PET BOTTLING LINE SIDEL FOR CARBONATED DRINKS Product: Carbonated water and soft drinks Production speed: 13,500 bottles per hour (BPH) PET Preform Presses – Sameto - Model: EBH 2050 - Year: 2010 PET Blower – Sidel - Model: SBO10 - Year: 2010 - Neck finish: ø28 1881 - Number of cavities: 10 Ffsdpfxjxz Ayts Aa Eew Air Conveyor – Alsim - Year: 1999 Monoblock – Alsim - Model: Asmojet 1T RV-P 48/60/10K - Year: 1999 - Rinser: 48 clamps, 1 water treatment - Filler: 60 isobaric valves - Capper: 10 heads Mixer – Alsim - Year: 1999 - Output: 30 m³/h Bottle Dryer – ACI - Year: 2015 Labeler – Krones Contiroll - Model: Contiroll - Year: 2004 - Type: Rotary labeler - Number of stations: 15 - Label type: PET wrap-around - Label feed: Roll-fed Shrink Wrapper – Acmi - Model: Fenix - Year: 2019 - Configuration: Film launching, film only Handle Applicator – Smipack - Model: HA 35-50-70 - Year: 2002 Palletizer – Alsim - Model: Valiant 1I 1P - Year: 1996 - Fully automatic, push-type system Pallet Wrapper – PM Pragometal - Model: OBS Rotomatic Standard - Year: 2009