Used Ima for sale (134)

Condition: excellent (used), LOADER (BRIDGE-FRAME) WITH DOUBLE PICK-UP STATION Csdpfx Afefi Tg Hjlsaa Vacuum system (with its pump) No. 2 Vertical supporting columns of the top supporting beam No. 1 Horizontal top supporting beam (where the carriage slide on) No. 1 Motorized sliding carriage with horizontal metal arms No. 2 Out-side rollers way (on gound) to in-feed pile of panels to the Loader Out-side motorized rollers table (which receives panels from the Loader) Separate electric and command panel Perimetral safety metal grids Working capacity (cycles/min) 16 (ca.) Min/Max panels thickness mm 10 / 50 (ca.) Min dimensions of the panels mm 250 x 320 (ca.) Max dimensions of the panels mm 1300 x 3000 (ca.) Total installed motor power Kw 30

Condition: excellent (used), Year of construction: 2009, functionality: fully functional, Single-Sided Narrow Edge Bander IMA NOVIMAT / CONTOUR / I / G80 / 790 / L20 with Servo Unit for Corner Copying MFA Year of Production: 2009 Condition: Very good Features: * Stable machine frame with mounted processing units * Electronically adjustable feed speed: 6–30 m/min (feed rate of processing units is not synchronized with full feed adjustment) * Feed chain guided in sliding rails with plastic pads and 80 mm wide rubber lining * Automatic lubrication of feed chain controlled by the machine program * Upper pressure roller: double V-belt, 70 mm wide, on ball-bearing rollers; electronically adjustable * CE-compliant machine safety * Noise-reducing and protective covers * Edge banding unit with drive enclosed in sealed oil bath and glue pot (1 main pressure roller + 5 auxiliary rollers); Quick-Lock pneumatic glue pot system for fast replacement * Touchscreen display * End trimming saw unit for cutting excess edge at front and rear corners, including: pneumatic saw adjustment 0–25°, straight cuts, corner chamfering, automatic saw positioning for two edge thicknesses (e.g., 0.4 and 1.2 mm), and excess edge adjustment for corner copying * All processing units equipped with chip extraction * Novimat Contour series maintains high processing quality due to powerful corner copying unit and minimal spacing between workpieces (\~300 mm) Basic Technical Data: * Roll edge thickness: 0.3–3 mm * Paper, PVC, and ABS edges: 0.3–3.0 mm * Veneer: 0.5–3.0 mm * Wooden strips: 0.8–20 mm * Edge height: 14–65 mm * Maximum top edge overhang: * Up to 8 mm thickness: 5 mm * Over 8 mm thickness: 2 mm Workpiece Dimensions: * Minimum length (feed direction): 150 mm * Minimum width (for thickness ≤25 mm): 65 mm * Minimum thickness: 8 mm (without flat planer) / 12 mm (with flat planer) * Maximum thickness: * Without corner copying: 60 mm * With corner copying: 40 mm * Smallest workpiece: 150 × 150 mm or 65 × 300 mm (\*65 mm width for max thickness 25 mm) Machine Parameters: * Electronically controlled feed: 6–30 m/min (may be limited by individual units) Codpfxew R S Slj Afljaa * Workpiece protrusion beyond feed chain: * 38 mm (edge thickness 0.3–8 mm) * 30 mm (edge thickness 8.1–20 mm) Power Supply: * Voltage: 400/230 V, ±5/–10% with neutral * Frequency: 50 Hz * Control voltage: 230 V AC / 24 V * Compressed air: 8 bar * Extraction air speed: 28 m/s

Condition: excellent (used), To apply bands on edges of straight, round and shaped workpieces - Manual feeding of the workpieces Codpfxohgbfae Afleaa - With glue tank and glue spreading roller - With coil/reel holding table - Min/Max thickness of the workpieces mm 16 / 40 - Edge tickness range mm 0.4 to 3 - Tiltable table 0°-45° - Total installed power KW 4 (ca.)

Condition: excellent (used), C.N.C. WORKING CENTER (POINT TO POINT) 5 axis (ROBOT head) Goose-neck type Numerical Control ICOS CNC - Software IMAWOP / (OPTION IMAwinCAD) Safety cabin (enclosure) of the working head Working table with pods and rails- No. 8 Support rails LED system on X-axe for the rails positioning and on Y-axe for the vacuum pods positioning Casdpfx Afjfin Saelsa Automatic Tools Changing System No. 2 Tools storage plates (No. 8 folds) + (No. 18 folds) Max. useful working area (X - Y - Z) mm 4300 x mm 1300 (mm 1410) x mm 350 No. 2 Working areas - Vacuum pump (capacity m3/h) 140 Separate electric and command cabinet. Total installed power (Kw) 23 WORKING GROUPS (TOP): No. 21 Independent vertical boring spindles No. 4 Independent horizontal boring spindles Drilling head motor-power (Kw) Kw 1,2 x 4 Circular Grooving Saw (tiltable 0°- 90°) diam. (mm) 125 No. 1 Vertical electro-spindles ROBOT (HSK F63), motor power KW 9 Independent Z-axis with a stroke of 650 mm Axis A arranged / assembled at an angle of 90° to the C axis. Rotating range of the C-axis 420°, rotating range of the A-axis 140°

Condition: excellent (used), SINGLE-SIDE EDGE BANDER (LEFT-side) Edges (band in rolls) thickness (Min/Max) mm 0,3 - 3 Edges thickness in stips / lippings (min/max) mm 3 - 12 Panels thickness (min/max) mm 8 - 60 Numerical Control ICOS open TS Feeding speed (adjustable) m/min 4 - 20 Top pressure system with rubber belt Spraying unit (Anti-sticking liquid) Pre-milling Unit (vertical joint trimmers) 08.376 (2 x Kw 3) Glueing Unit (Hot Melt Glue) 283.1513 Band Pressure zone Cedoflc Uhepfx Afloaa Edge coils supporting unit (reels N°) 1 Snipping (end-cutting) unit 08.415 (2 x Kw 0,66) Fine Trimming unit 08.055 (2 x Kw 1) 0°-30° Multi Function Unit (Profile contour Trimming unit) 08.342 (2 x Kw 0,66) Profile edge scraping unit 08.519 Glue scraping unit 08.50 Buffing unit 08.612 (2 x Kw 0,25) Free space

Condition: as good as new (ex-display), SINGLE-SIDE EDGE BANDER (LEFT-side) Edges (band in rolls) thickness (Min/Max) mm 0,3 / 3 - in stips / lippings mm max 1 Panels thickness (min/max) mm 8 / 60 (Laser - max 44) Numerical Control ICOS Open Feeding speed (adjustable) m/min 16 - 30 Top pressure system with rubber belt Spraying unit (Anti-sticking liquid) In-feed fence, adjustable by N.C. Panels in-feed system 700.101 (mm 500 x 500) Pre-milling Unit (vertical joint trimmers) 08.379 (2 x Kw 4,0) adjustable by N.C. Glueing Unit (P.U.R. Glue + Quick Melt system) 04.0836 + 283.1518 (SERVO-MOTOR band feed) adjustable by CN Glueing Unit (Thermofusion with Laser) Laser System IMALUX Spraying Unit (for anti-release liquid) Band Pressure zone + Edge coils supporting unit (No. 6 reels) Snipping (end-cutting) Linear 08.428 LKA V30/2(Kw 0,2 x 2) work speed up to 30 m/min (0°-25°) Csdpfx Afsgbug Njleaa Fine Trimming unit (Multi-profile, by N.C.) 08.0587 (Kw 1.0 x 2) 4 profiles Multi-Profile Copying unit by N.C (fine and contour trimming) KFA 20 (Kw 0,5 x 1) max 25 m/min Profile edge scraping unit DUO (4 profiles) Glue scraping unit 08.521 Spraying Unit (for polishing liquid) Buffing unit 08.617-4 (Kw 0.18 x 4) Milling grooving unit 2 x 08.190 (Kw 4,5 x 2) swivelling 90°/180°/270° (adjustable by CN)

Condition: excellent (used), C.N.C. WORKING CENTER with 4 axes (X-Y-Z-C) for routering, boring, cutting and edge banding Numerical Control IMATRONIC 231 (IMAWOP) Max useful working area (without edge banding process) mm 5000 x 1630 x 100 Max useful working area (edge banding process) mm 3900 x 1450 x 60 (panel thickness) No. 8 movable rails (supports) length mm 1200 LED displaying both the axe X and axe Y position Vacuum cups (with No. 1 vacuum pump, capacity 140 m3/h) Safety side metal grids and front emergency carpets Motorized belt to evacuate the wastes from the working process No. 2 Vertical Electro-spindles HSK F63 (1 x Kw 11 + 1 x Kw 7,5) Automatic Tools Changing System, with 18 folds (places) No. 21 Independent vertical boring spindles (4 x Kw 1,2) Casdpfofbmqtox Aflea No. 6 Independent horizontal boring spindles (1 x Kw 3) Banding group on board - Glueing Unit (Hot Melt Glue) VT 50 Edge coils supporting unit (No. 6 reels) OPTIONALS: No. 1 Circular Saw to cut and for grooving - max diam mm 200 (90°) No. 1 Aggregate Flush-Trimming/Scraping Unit No. 1 Cross aggregate with No. 4 horizontal boring spindles

Condition: excellent (used), LOADER (BRIDGE-FRAME) WITH DOUBLE PICK-UP STATION Vacuum system (with its pump) No. 2 Vertical supporting columns of the top supporting beam No. 1 Horizontal top supporting beam (where the carriage slide on) No. 1 Motorized sliding carriage with horizontal metal arms N. 2 Out-side rollers ways (on gound) to in-feed pile of panels to the Loader N. 1 Out-side motorized rollers table (which out-feed the panels from the Loader) Separate electric and command panel Perimetral safety metal grids Casdpfowbp Nwsx Aflja Working capacity (cycles/min) 16 (ca.) Min/Max panels thickness mm 10 / 50 (ca.) Min dimensions of the panels mm 250 x 320 (ca.) Max dimensions of the panels mm 1300 x 3000 (ca.) Total installed motor power Kw 80

Condition: excellent (used), SINGLE-SIDE EDGE BANDER (LEFT-side) Edges (band in rolls) thickness (Min/Max) mm 0,3 - 3 Edges thickness in stips / lippings (min/max) mm 3 - 12 Panels thickness (min/max) mm 8 - 60 Numerical Control ICOS open TS Feeding speed (adjustable) m/min 4 - 20 Top pressure system with rubber belt Spraying unit (Anti-sticking liquid) Pre-milling Unit (vertical joint trimmers) 08.376 (2 x Kw 3) Glueing Unit (Hot Melt Glue) 283.1513 Band Pressure zone Edge coils supporting unit (reels N°) 1 Snipping (end-cutting) unit 08.415 (2 x Kw 0,66) Fine Trimming unit 08.055 (2 x Kw 1) 0°-30° Multi Function Unit (Profile contour Trimming unit) 08.342 (2 x Kw 0,66) servo Profile edge scraping unit 08.519 Glue scraping unit 08.50 Buffing unit 08.612 (2 x Kw 0,25) Free space Cedpfx Afsd Nuu Heljaa

Condition: excellent (used), C.N.C. WORKING CENTER 4 axes (X-Y-Z-C) Goose-neck type, with Numerical Control ICOS-Open. Software IMAWOP / IMATRONIC - BIMA Fast Cut Working table with pods and rails. No. 8 Supports (rails) of length mm 1400 Automatic deplacement by CNC (X axis) of the Supports/rails Automatic deplacement by CNC (Y axis) of the vacuum pods/cups Automatic Tools Changing System. Tools storage plate (No. 18 folds- positions) Max. useful working area (X - Y - Z) mm 4200 x 1600 x 60 Min. workpieces dimensions (X - Y - Z) mm 295 x 115 x 14 Max. workpieces dimensions (X - Y - Z) mm 4250 x 2200 x 60 Motorized carpet to evacuate chips and wastes Separate electric and command cabinet. Total installed power (Kw) 28 WORKING GROUPS (TOP): Caodpfx Aovxhnusflja Vertical electro-spindle 1 x HSK F63 - electro-spindle motor power Kw 14,5 (S6) / Kw 7,5 (S1) N° 3 Clamps to fix the panel and move it on to the machine (on top of the vacuum pods) N° 5 Air cushion tables (for the panel parking before being processed) Vacuum system with suction cups (controlled by CN) to lift panel onto outfeed belts Workpieces Outfeed system (from Bima Cut) with system with motorized belts

Condition: excellent (used), FULL LINE OF 4 SIDE SIZING-MILLING & EDGE BANDING Cedpfx Afeun N Dlolsaa Composed of the following machines: A) W06027 1st Double Side Sizing & Edgebander "IMA" Mod. Combima II / 440 /A / R3 B) Turning Station 90° C) W06028 2nd Double Side Sizing & Edgebander "IMA" Combima II / 190 / B / R3

Condition: excellent (used), SINGLE-SIDE EDGE BANDER (LEFT-side) Edges (band in rolls) thickness (Min/Max) mm 0,3 / 3 Edges thickness in strips / lippings (min/max) mm 0,8 / 20 Panels thickness (min/max) mm 8 / 60 Numerical Control ICOS Open Compact Feeding speed (adjustable) m/min 6 - 30 Top pressure system with rubber belt In-feed fence, adjustable by N.C. Pre-milling Unit (vertical joint trimmers) by N.C. 08.376 (Kw 4,5 x 2) Lamps to heat the workpieces side Glueing Unit (Hot Melt Glue + Quick Melt system) 283.1513 + 283.201 Band Pressure zone Caodjidqphepfx Afloa Edge coils supporting unit (reels N°) 1 Snipping (end-cutting) unit 08.42 (Kw 0,66 x 2) 0°-25° - max 30 m/min, Fine Trimming unit 08.055 (Kw 1,85 x 2) 0°-30° Spraying Unit (for sliding liquid) Multi-Profile Copying unit by N.C (fine and contour trimming) 08.348 (KW 0,66 x 2) 4 profiles Profile edge scraping unit 08.516 (4 profiles) Glue scraping unit 08.50 Spraying Unit (for polishing liquid) Buffing unit 08.612- 2 (Kw 0,25 x 2) Milling grooving unit 08.183 (Kw 3 x 1)

Condition: excellent (used), C.N.C. WORKING CENTER with 4 axes (X-Y-Z-C) for routering, boring, cutting and edge banding Goose-neck type, with Numerical Control ICOS-Open. Software IMAWOP + IMAwinCAD Working table with pods and rails. No. 6 Supports (rails) of lenght mm 1450 - DYNAPOINT Casdpfxjtixpus Aflea Automatic deplacement by CNC (X axis) of the Supports/rails Automatic deplacement by CNC (Y axis) of the vacuum pods/cups Automatic Tools Changing System. Tools storage plate (No. 18 folds- positions) Max. useful working area (X - Y - Z) mm 6300 x 1450 x 100 Min. workpieces dimensions (X - Y - Z) mm 320 x 115 x 14 Max. workpieces dimensions (X - Y - Z) mm 5600 x 2100 x 38 Motorized carpet to evacuate chips and wastes Separate electric and command cabinet. Total installed power (Kw) 34 WORKING GROUPS (TOP): Vertical electro-spindle 1 x HSK F63 - electro-spindle motor power Kw 18 (S6) Circular Grooving Saw (90°) diam. (mm) 200 Edge Banding unit (always ready on board) - VT 100 Edge coils supporting unit (No. 2 reels) Combined aggregate (Flush-Trimming/Scraping) Workpieces Infeed system (to the Bima Cut) with Brush Table N° 6 Clamps to fix the panel and move it on to the machine (on top of the vacuum pods) Workpieces Outfeed (from Bima Cut) With motorized Rollers + Angular Transfer System

Condition: excellent (used), SINGLE-SIDE EDGE BANDER (LEFT-side) Edges (tape) thickness in rolls (min/max) mm 0,3 / 3 Veneer edges limited possible up to max. 1.0 mm Panels thickness (min/max) 8 mm. 40 mm (with MFA) / 60 mm (without MFA) Numerical Control / Software ICOS Open Adjustable feeding speed (m/min ) 6 - 30 Top pressure system with driven rubber belt Spraying unit (Anti-sticking liquid) In-feed fence Pre-milling Unit (vertical joint trimmers) 08.378 (2 x Kw 4,5) Glueing Unit (Hot Melt glue) 04.1570 Pressure zone Edge coils supporting unit (No. of reels) 2 Csdpor Ttflofx Afleaa Snipping (end-cutting) unit 08.42/30/B (2 x Kw 0,66) 0°-25° (max 30 m/min) Fine Trimming unit 08.055 (2 x Kw 1) 0°-30° Multi Function Unit (Profile contour Trimming unit) by N.C. 08.342 (2 x Kw 0,66) servo Profile Scraping unit 08.519 Glue scraping unit 08.50 Buffing unit 08.617 (2 x Kw 0,25) Milling grooving unit 08.190 (1 x Kw 4,5)

Condition: excellent (used), FLEXIBLE SYSTEM OF SINGLE-SIDE SIZING-EDGEBANDING (BATCH SIZE ONE) Composed of the following machines: M.01) PANELS HANDLING and RETURN SYSTEM "SIRIO" BATCH SIZE ONE M.02) SINGLE-SIDE RIGHT-HAND SIZE-EDGE BANDER "IMA" Novimat /I/R75/690/R3 Panels thickness (min/max) mm 8 / 60 - Working width (min/max) mm 200 / 1300 Edges (tape) thickness in rolls (min/max) mm 0,3 / 3 Numerical Control / Software ICOS Open (Batch Size One) Adjustable feeding speed (m/min ) 6 - 30 Panels in-feed system A1 / 15 N° 2 Pre-milling Unit (vertical joint trimmers) adjustable by N.C. 08.378 (4 motors x Kw 4,5) Glueing Unit (Hot Melt + Quick Melt Unit) VTG + 283.205 Cjdpekt Uuaofx Afleaa Edge coils supporting unit (No. 24 reels) Snipping (end-cutting) unit 08.42 / 30 / B / LS1 (2 x Kw 0,2) 0°-25° Rough Trimming unit 08.055.0.1680 (1 x Kw 0,85) Fine Trimming unit (Multi-profile, adjustable by N.C.) 08.0587 HS/LS1 (2 x Kw 1) Multi-Profile Copying unit by N.C. (fine and contour trimming) KFA x20 (1 x Kw 0,5) 20 m/min Profile Scraping unit (Multi-profile, adjustable by N.C.) 08.516 HS/LS1 Glue scraping unit 08.521 Buffing unit 08.617-2 (2 x Kw 0,18) N° 3 Milling grooving unit 08.190 (3 x Kw 4,5) Controlled by N.C. - (90°/180°/270°) M.03 ) PORTAL BRIDGE (UNLOADING/LOADING) "SIRIO"

Condition: excellent (used), C.N.C. WORKING CENTER with 4 axes (X-Y-Z-C) for routering, boring, cutting and edge banding Numerical Control ICOS CNC (IMAWOP) Max useful working area (without edge banding process) mm 3100 x 2000 x 100 Max useful working area (edge banding process) mm 3100 x 1925 x 60 (panel thickness) No. 6 movable rails (supports) length mm 1400 LED displaying both the axe X and axe Y position Vacuum cups (with No. 1 vacuum pump, capacity 250 m3/h) Safety side metal grids and front emergency carpets Cedpjq Nmutjfx Afljaa No. 1 Vertical Electro-spindle HSK F63 ( Kw 18) Automatic Tools Changing System, with 18 folds (places) No. 14 Independent vertical boring spindles (2 x Kw 1,2) Aggregate Boring Unit, "cross" shape, with 4 horizontal spindles + Circular saw (diam. mm 125) Banding group on board - Glueing Unit (Hot Melt Glue) VT 100 Edge coils supporting unit (No. 2 reels) OPTIONALS: No. 1 Aggregate "FLEX 5" Mod. VARIO NC No. 1 Aggregate Flush Milling / Trimming No. 1 Aggregate Flush-Trimming / Profile Scraping Unit No. 1 Bar Code Reader

Condition: excellent (used), SINGLE-SIDE EDGE BANDER (LEFT-side) Edges (band in rolls) thickness (Min/Max) mm 0,3 / 3 - in stips / lippings mm max 1 Panels thickness (min/max) mm 14 / 60 (LASER - Max 50) Numerical Control ICOS Open Feeding speed (adjustable) m/min 6 - 30 Top pressure system with rubber belt Spraying unit (Anti-sticking liquid) In-feed fence, adjustable by N.C. Panels in-feed (servo) system A1 / 15 Pre-milling Unit (vertical joint trimmers) 08.378 (2 x Kw 4,5) adjustable by N.C. Glueing Unit (P.U.R. Glue + Quick Melt unit) 283.201 + 283.203 Glueing Unit (Thermofusion with Laser) Laser System LASERLINE Spraying Unit (for anti-release liquid) Band Pressure zone + Edge coils supporting unit (No. 36 + 12 reels) Snipping (end-cutting) 08.42 (Kw 0,2 x 2) work speed up to 30 m/min (0°-25°) Rough Trimming unit 08.0555 HS/LS1 (Kw 1 x 2) Fine Trimming unit (Multi-profile, by N.C. adjustment, for 4 profiles) 08.0587 (Kw 0,66 x 1) Multi-Profile Copying unit by N.C (fine + contour trimming) KFA 30 (Kw 0,5 x 1) max 30 m/min Profile Scraping unit (Multi-profile, by N.C. adjustment, for 4 profiles) 08.0516 Glue scraping unit 08.521 Csdpfx Asi Hn Srsfljaa Spraying Unit (for polishing liquid) Buffing unit 08.614 (Kw 0.25 x 4) No. 2 Milling grooving units 08.190 (Kw 4,5 x 2) swivelling 90°/180°/270° (adjustable by CN)

Condition: excellent (used), Double side - Independent Machine (or 1st and/or 2nd in a line) Edges (band in rolls) thickness (Min/Max) mm 0,3 / 3 Edges thickness in strips/lippings (Min/max) mm 3 / 10 Panels thickness (min/max) mm 8 / 60 Working width (min/max) mm 236 / 3300 Numerical Control /Software ICOS Open Adjustable feeding speed (m/min ) 10 - 50 - Without Transmission bar (Master & Slave system) Distance (center-axes) of the Disappearing Dogs (mm) 1080 SIZING PART (for each side): Anti-chipping Milling Unit 75.186 (1 x Kw 4,4) Hogging Units (2 x kW 8) Free Space (for Milling unit) Codpfx Afjd Nt Rqelsaa EDGE-BANDING PART (for each side): Glueing Unit (Hot Melt Glue) 04.1570 + 283.205 Band Pressure zone - Edge coils supporting unit (No. 6 reels) Snipping (end-cutting) unit 08.42 (2 x Kw 0,66) speed 30 m/min (0° - 25) Fine Trimming unit 08.055 (2 x Kw 1) / 0° - 30° Multi Function Unit (Profile contour Trimming unit) 08.342 (2 x Kw 0,66) with servo-motors Profile edge scraping unit 08.519 Glue scraping unit 08.521 Spraying Unit (for polishing liquid) Buffing unit 08.617-4 (4 x Kw 0,18) Milling grooving unit 08.190 (1 x Kw 4,5) 90°-180°-270°

Condition: refurbished (used), SINGLE SIDE EDGE BANDER (Left) Edges (band in rolls) thickness (Min/Max) mm 0,3 - 3 Edges thickness in stips / lippings (min/max) mm 3,0 - 12,0 Panels thickness (min/max) mm 8 - 60 Numerical Control ICOS Feeding speed (fixed) m/min 16 Top pressure system with rubber belt Spraying unit (Anti-sticking liquid) Pre-milling Unit (vertical joint trimmers) 08.376 (2 x kW 3,0) Lamps to heat the workpieces side Glueing Unit (Hot Melt Glue) 283.1513 Band Pressure zone Edge coils supporting unit (reels N°) 1 Cjdsdfgfpspfx Aflsaa Snipping (end-cutting) unit 08.415 (2 x kW 0,66) Fine Trimming unit 08.055 (2 x kW 1) - 30° Multi Function Unit (Profile contour Trimming unit) 08.346 (2 x kW 0,66) Profile edge scraping unit 08.519 Glue scraping unit 08.50 Spraying Unit (for polishing liquid) Buffing unit 08.612 (2 x kW 0,25) Free space

Condition: reconditioned (used), Double-side Sizing-Milling & Edge Banding - First (1st) machine in a line Edges (band in rolls) thickness (Min/Max) mm 0,3 / 3 Panels thickness (min/max) mm 8 / 45 Working width (min/max) mm 236 / 1300 Numerical Control /Software ICOS Open Adjustable feeding speed (m/min ) 10 / 50 Without Transmission bar (Master & Slave system) Safety and sound-proof enclosures/cabins Caodpfodh Tfgox Afloa SIZING PART (for each side): Spraying unit (Anti-sticking liquid) Milling Unit (vertical Joint Trimmers) 08. 0555 max. 3° (2 x 1 kW) Free space EDGE-BANDING PART (for each side): Glueing Unit (Hot Melt Glue + Quick Melt system) 04.1570 Band Pressure zone Edge coils supporting unit (reels N°) 6 Rough Trimming unit 08. 0555 (2 x 1 kW) max. 3° Fine Trimming unit 08. 055 (2 x 0,66 kW) 30° + 30 m/min Glue scraping unit 08.517 Spraying Unit (for polishing liquid) Buffing unit 08.617-2 (2 x 0,18 kW) Free space

Condition: excellent (used), Double side - Stand-alone Machine (or 1st and/or 2nd in a line) Edges (band in rolls) thickness (Min/Max) mm 0.3 / 3 Edges thickness in stips / lippings mm 1,3 Panels thickness (min/max) mm 8 / 40 Working width (min/max) mm 266 / 2400 (option 3000) Distance (center-axes) of the Disappearing Dogs (mm) 540 (prepared for 270 mm) Numerical Control ICOS OPEN Feeding speed (adjustable) max. 60 m/min Without Transmission bar (Master & Slave system) SIZING PART (for each side): Spraying unit (Anti-sticking liquid) Pre-milling Unit (vertical joint trimmers) 08.376 (KW 4.5 x2) Free space EDGE-BANDING PART (for each side): Glueing Unit (Hot Melt Glue) 283.205 Band Pressure zone. Caedpsu Ekbnsfx Aflea Edge coils supporting unit (No. 2 reels) Servo-drive Snipping (end-cutting) unit 08.42 (KW 0.2 x 2) 0°-25° (max. working speed 50 m/min) Fine Trimming unit 08.055 (KW 0,66 x 2) 0°-30° Multi Function Unit (Profile contour Trimming unit) 08.342 (KW 0.66 x 2) Spraying Unit (for polishing liquid) Free space (for possible addition of a scraper) Buffing unit 08.617 (Kw 0.18 x 2)

Condition: refurbished (used), SINGLE-SIDE SIZING & EDGE BANDING MACHINE (Left side machine) Edges (tape) thickness in rolls (min/max) mm 0,3 - 3 Edges thickness in stips / lippings (min/max) mm 1 ALU Panels thickness (min/max) mm 6 - 55 Numerical Control /Software IMATRONIC 121 /01 Adjustable feeding speed (m/min ) 6 - 30 SIZING PART : Cjdpfscr T N Dsx Aflsaa Pre-milling Unit (vertical joint trimmers) adjustable by N.C. (2 x Kw 4,5) 08.376 Spraying unit (Anti-sticking liquid) EDGE-BANDING PART : Lamps to heat the workpieces side + Glueing Unit (P.U.R. Glue + Quick Melt unit) 04.1569 Band Pressure zone mm 1000 + Edge coils supporting unit (N. 6 reels) Snipping (end-cutting) unit 08.42 (2 x Kw 0,66) working speed 25 m/min (swivelling 0-25°) Rough Trimming unit 08.0555 (2 x Kw 1) Fine Trimming unit 08.055 (2 x Kw 1) 30° + Spraying Unit (for sliding liquid) Multi-Profile Copying unit 08.348 (fine and contour trimming) adjustment by N.C (2 x Kw 0,66) Profile edge scraping unit (Multi-profile, adjustable by N.C.) 08.516 Glue scraping unit 08.517 (Pneumatic) Spraying Unit (for polishing liquid) Buffing unit 08.614 (2 x Kw 0,25) Milling grooving unit 08.183 (1 x Kw 3) Smoothing unit with spheres 08.53 Chamfer Sanding Unit for straight edges WI (4 x Kw 0,75)

Condition: excellent (used), Double side - Independent Machine (or 1st and/or 2nd in a line) Edges (tape) thickness in rolls (min/max) mm 0,3 / 3 Panels thickness (min/max) mm 8 / 45 (60) Working width (min/max) mm 236 / 1300 Numerical Control / Software ICOS Open (Windows base) Without Transmission bar (Master & Slave system) Adjustable feeding speed (m/min ) 10 - 50 Safety and sound-proof enclosures/cabins "Hopper Feeder" (panels fall directly onto the feeding chains) Distance (center-axes) of the Disappearing Dogs (mm) 270 SIZING PART (for each side): Cajdpeum Untsfx Afloa Spraying unit (Anti-sticking liquid) Anti-chipping Milling Unit 75.186 (1 x Kw 4,4) Hogging Units (2 x Kw 6,6) Free space EDGE-BANDING PART (for each side): Glueing Unit (Hot Melt + Quick Melt Unit) 04.1570 + 283.201 Pressure zone Edge coils supporting unit (No. of reels) 6 Snipping (end-cutting) unit 08.42 (2 x Kw 0,66) 30 m/min (0°-25°) Fine Trimming unit 08.055 (2 x Kw 0,66) 30 m/min Glue scraping unit 08.521 Spraying Unit (for polishing liquid) Buffing unit 08.617-2 (2 x Kw 0,18) Free space

Condition: excellent (used), C.N.C. WORKING CENTER with 5 axes (X-Y-Z-C-5) routering, boring, cutting and edge banding Goose-neck machine - Front emergency carpets Safety cabin (enclosure) of the working head Numerical Control Type ICOS CNC - Software IMAWOP Working table with pods and rails (No. 8 rails x mm 1400) LED system (on the rails) for the vacuum pods positioning Automatic Tools Changing System (Store with No. 18 positions) Useful working area (X - Y - Z) mm 4000 x 2100 x 300 Useful working area (X -Y - Z) in edge banding mm 4000 x 1800 x 60 Nr. 2 Working areas - Vacuum pump / capacity (m3/h) 140 Cjdpfshu U Nxsx Aflsaa Motorized carpet to evacuate the wastes from the working process Separate electric and command cabinet - Total power installed Kw 32 Working group (top head) Nr. 21 Independent vertical boring spindles (4 X Kw 1,2) Nr. 1 Vertical Electro-spindle HSK F63 ROBOT (Kw 16) Edge Banding group (ready on board) with Glueing Unit (Hot Melt) VT 100 Edges (tape) thickness in rolls (min/max) mm 0,4 / 3 Edge coils supporting unit (Nr. 2 reels) OPTIONALS: Circular saw aggregate (diam. mm 200) Combined aggregate (Flush-Trimming/Scraping) Drilling Aggregate (with 4 horizontal boring spindles)

Condition: excellent (used), Double-side Sizing-Milling & Edge Banding - First (1st) machine in a line Edges (tape) thickness in rolls (min/max) mm 0,3 / 3 Panels thickness (min/max) mm 8 / 45 (60) Working width (min/max) mm 236 / 1300 Numerical Control / Software ICOS Open (Windows base) Adjustable feeding speed (m/min ) 10 - 50 Safety and sound-proof enclosures/cabins SIZING PART (for each side): Hogging Units 75.30 (2 x Kw 6,6) Free space EDGE-BANDING PART (for each side): Cedpfx Aounrwnjfljaa Glueing Unit (Hot Melt + Quick Melt Unit) 04.1570 + 283.201 Pressure zone Edge coils supporting unit (No. of reels) 6 Rough Trimming unit 08.055 (2 x Kw 1) 0°-30° Fine Trimming unit 08.055 (2 x Kw 0,66) 0°-30° Profile Scraping unit 08.515 Free space Buffing unit 08.617-2 (2 x Kw 0,18) Nr. 2 Milling grooving units RIGHT: 75.30 (2 x Kw 4,4) 90°-180°