Condition: new, capacity 90 degrees: round 350 mm capacity 90 degrees: square 330 mm 500 x 310 band speed 15 - 100 m/min table height 844 mm dimensions of saw-band 4250 x 34 x 1,1 mm total power requirement 2,2 kW weight of the machine ca. 1,2 t dimensions of the machine ca. 1,4 x 2,4 x 1,935 m ACTION PRICE!!! 2-column double miter band saw K-tech DG 50/33 HA-I • 2-column miter saw • Solid, yet easy to use • Material height sensor (automatic cut start detection) • Smooth running thanks to bevel cut, feed controller + cutting pressure controller • Massive material infeed roller • Removable chip tray (disinfection) • Energy-saving and low-vibration thanks to bevel cut • Ergonomic, safe and free-standing control panel • Frequency-controlled saw drive 15 -100 m/min. • Hydraulic cutting pressure control valve • Hydraulic control of saw frame and vice • LEDs for monitoring all safety functions • Large dimensioned wheels (520 mm) a. • Clear miter setting up to 60° Semi-automatic function: 1. Clamp material 2. Saw starts 3. Rapid lowering to the start of the material or the same for series cutting cut 4. Saw band off Fgjdpsfg E Hlefx Ag Rea 5. Raise the frame to just above the material 6. Open the vise

Condition: new, capacity 90 degrees: round 305 mm capacity 90 degrees: square 260 mm 350 x 200 saw band length 3375 x 27 x 0,9 mm band speed 37 + 74 m/min table height 940 mm total power requirement 1,5/1,8 kW weight of the machine ca. 0,61 t dimensions of the machine ca. 1,5 x 1,75 x 1,9 m Double miter metal band saw with AutoCut function - Miter cuts up to 60° left and 45° right - Ball bearing turntable - Vice can be moved sideways Fedpfx Aefd Abaog Rsga - Massive, large material support - Automatic cooling Figure is semi-automatic.

Condition: new, cutting diameter 255 mm saw band length 2765x 0,9 x 27 mm cutting width 300 x 180 mm turning speeds 35 + 70 U/min total power requirement 1,8 kW weight of the machine ca. 450 t dimensions of the machine ca. 1,7 x 1,23 x 1,75 m SPECIAL PRICE!!! Double miter metal band saw, frequency converter hydraulic semi-automatic GBS 250 Super HA-I Easy • miter left 60° + right 45° • Material height sensor (automatic cut start detection) • Frame and gear made from one piece, very quiet cut and very low vibration • Hydraulic vice can be moved sideways a. • Guided, high quality industrial bearings • Solid vice + machine casting • Large machine bed • Machine base with tool compartment and chip drawer • Cut monitoring by ammeter • Cutting pressure feed regulator Fgedpfx Asfn Andeg Rea • Support roller (infeed side) • Ball bearing turntable Semi-automatic function: 1. Clamp material 2. Saw starts 3. Rapid lowering to the start of the material or the same for series cutting cut 4. Saw band off 5. Raise the frame to just above the material 6. Open the vise

Condition: new, capacity 90 degrees: round 680 mm capacity 90 degrees: square 640 mm 820x610 saw band length 5850 x 41 x 1,3 mm band speed 15 - 100 m/min table height 800 mm total power requirement 5,5 kW weight of the machine ca. 4,45 t dimensions of the machine ca. 5,85 x 3,6 x 2,7 m 2-column band saw for quick cutting, K-tech 800H with pusher system P 15. P 30 (option), Fast, quiet and ergonomic cutting Special development for cutting profiles and beams as well as solid material. The material is fixed vertically on and section sides. The machine is from K-tech 800 H standard with an additional horizontal vice equipped. The interaction of the hydraulic Saw frame lowering, material positioning and the Pusher system is CNC controlled. The machines come standard with the environmentally friendly Fgedpfx Asfgyifog Roa “B&S-Clean Cut cutting system” with minimal quantity lubrication equipped. This saves cleaning effort and is gentle Resources. CNC Control A CNC control allows programming of up to up to 90 cutting programs with different cut lengths, Quantities and mitres. The B&S pusher system, feeding and positioning system, is marked “on both sides “Opening gripping tongs” which are hydraulically controlled. This ensures safe gripping and transport of materials and Bundles that deviate slightly from the ideal shape. The pusher system is separate constructed and ground using ball-bearing linear guides Rack and guided by a frequency-driven, robust geared motor.

Condition: new, capacity 90 degrees: round 680 mm capacity 90 degrees: square 640 mm 1250x600 saw band length 8140x54x1,6 mm band speed 15 - 90 m/min table height 855 mm total power requirement 7,5 kW weight of the machine ca. 4,96 t dimensions of the machine ca. 5,7 x 4,0 x 2,75 m 2-column band saw for quick cutting, K-tech 1200H with pusher system P 30. P 60 (option), Fast, quiet and ergonomic cutting Special development for cutting profiles and beams as well as solid material. The material is fixed vertically on and section sides. The machine is from K-tech 800 H standard with an additional horizontal vice equipped. The interaction of the hydraulic Saw frame lowering, material positioning and the Pusher system is CNC controlled. The machines come standard with the environmentally friendly “B&S-Clean Cut cutting system” with minimal quantity lubrication equipped. This saves cleaning effort and is gentle Resources. CNC Control A CNC control allows programming of up to up to 90 cutting programs with different cut lengths, Quantities and mitres. Fjdsfgyigspfx Ag Rsga The B&S pusher system, feeding and positioning system, is marked “on both sides “Opening gripping tongs” which are hydraulically controlled. This ensures safe gripping and transport of materials and Bundles that deviate slightly from the ideal shape. The pusher system is separate constructed and ground using ball-bearing linear guides Rack and guided by a frequency-driven, robust geared motor.

Condition: new, capacity 90 degrees: round 255 mm capacity 90 degrees: square 240 mm 300 x 180 saw band length 2.765 x 27 x 0,9 mm mm table height 870 mm band speed 18 - 110 m/min Control CNC total power requirement 1,5/1,8 kW weight of the machine ca. 0,63 t dimensions of the machine ca. 1,8 x 1,85 x 1,85 m Miter band saw, fully automatic GBS 255 Super VA-I CNC • miter left 45° automatic operation • miter left 60° semi-automatic operation (cuts without programming) • Material height sensor (automatic cut start detection) Fodpfx Agod Iipze Rega • Frame and gearbox made from one piece, very quiet cut and very low vibration • Removable chip tray (disinfection) • Shockproof and ergonomic control panel with oil-resistant EPDM cover • High performance positioning with incremental encoder (CNC) c. • Top access to the saw, material and feed unit • Hinged safety cover • Fine feed adjustment • Semi-auto. Cut! • Optimize work processes with CNC control Possibility to enter various parameters such as quantities and material lengths, automatic calculation of the cutting channel • CNC control for 10 different saw programs with 99 sub-programs for different lengths and quantities, e.g. 1 cutting program with various section lengths • Automatic feed unit (CNC) via ball roller spindle incremental feed with automatic length compensation. Adjustable for section lengths of 2 mm to 9,999 mm, remainder length 170 mm.

Condition: new, capacity 90 degrees: round 680 mm capacity 90 degrees: square 640 mm 820x610 capacity 45 degrees: round 550 mm capacity 45 degrees: square 550 mm capacity 45 degrees: flat 550x600 mm capacity 60 degrees: round 370 mm capacity 60 degrees: square 370 mm capacity 60 degrees: flat 370x600/450 mm saw band length 7260 x 41 x 1,3 mm Fjdjfg E Hmopfx Ag Rsga band speed 15 - 100 m/min table height 800 mm total power requirement 5,5 kW weight of the machine ca. 4,8 t dimensions of the machine ca. 5,85 x 3,7 x 2,7 m 2-column double miter band saw for quick cutting with pusher system P15. Option P30 Hydraulic saw frame lowering • NC controlled • Automatic angular positioning from + 60° to – 60° High quality automatic miter adjustment Special development for cutting profiles and beams. The highest positioning accuracy is achieved via the new “B&S positioning system”. reached. An intelligent NC control ensures smooth interaction of linear encoder and self-braking positioning motor in conjunction with a reliable hydraulic brake using large radial center positioning. The work table is supported by high-quality preloaded bearings, which ensure very smooth rotation. CNC Control A CNC control allows the programming of up to 90 cutting programs with different section lengths, quantities and mitres. Positioning system gripping on both sides The B&S pusher system, feeding and positioning system, is marked “on both sides “Opening gripping tongs” which are hydraulically controlled. This ensures safe gripping and transport of materials and Bundles that deviate slightly from the ideal shape. The pusher system is separate constructed and ground using ball-bearing linear guides Rack and guided by a frequency-driven, robust geared motor.

Condition: new, capacity 90 degrees: round 680 mm capacity 90 degrees: square 640 mm 1250x600 mm capacity 45 degrees: round 680 mm capacity 45 degrees: square 600 mm capacity 45 degrees: flat 870x600 mm capacity 60 degrees: round 580/550 mm capacity 60 degrees: square 530/450 mm capacity 60 degrees: flat 550x450 mm saw band length 8140 x 54 x 1,6 mm band speed 15 - 90 m/min table height 855 mm total power requirement 7,5 kW weight of the machine ca. 5,3 t dimensions of the machine ca. 5,75 x 4,2 x 2,75 m 2-column double miter band saw for quick cutting with pusher system P15. Option P30 Hydraulic saw frame lowering • NC controlled • Automatic angular positioning from + 60° to – 60° High quality automatic miter adjustment Special development for cutting profiles and beams. The highest positioning accuracy is achieved via the new “B&S positioning system”. reached. An intelligent NC control ensures smooth interaction of linear encoder and self-braking positioning motor in conjunction with a reliable hydraulic brake using large radial center positioning. The work table is supported by high-quality preloaded bearings, which ensure very smooth rotation. CNC Control A CNC control allows the programming of up to 90 cutting programs with different section lengths, quantities and mitres. Positioning system gripping on both sides The B&S pusher system, feeding and positioning system, is marked “on both sides “Opening gripping tongs” which are hydraulically controlled. This ensures safe gripping and transport of materials and Bundles that deviate slightly from the ideal shape. The pusher system is separate Fsdpfxjfg E Hnj Ag Rjga constructed and ground using ball-bearing linear guides Rack and guided by a frequency-driven, robust geared motor.

Condition: new, capacity 90 degrees: round 105 mm capacity 90 degrees: square 100 mm 100 x 105 dimensions of saw-band 1335 x 13 x 0,65 mm dimensions 650 x 310 x 300 m band speed 30 - 80 m/min total power requirement 0,95 kW weight of the machine ca. 18 kg Fgodjfv Aq Repfx Ag Rja Action Price!! Berg & Schmid - assembly band saw PBS 90 ESC Powerful and particularly robust metal band saw with Die-cast aluminum saw table and stepless cutting speed for Miter cuts up to 60° Share of freight costs: EUR 25.

Condition: new, capacity 90 degrees: round 310 mm capacity 90 degrees: square 280 mm Fgjdpfxjd Iiprj Ag Rja 400x250 saw band length 4020x34x1,1 mm band speed 18 - 100 m/min table height 890 mm total power requirement 2,2 kW weight of the machine ca. 0,99 t dimensions of the machine ca. 1,85 x 2,2 x 2,0 m Miter band saw, fully automatic, GBS 310/400 VA-I CNC • miter left 45° automatic operation • miter left 60° semi-automatic operation (cuts without programming) • Material height sensor (automatic cut start detection) • Frame and gear made from one piece, very quiet cut and very low vibration • Removable chip tray (disinfection) • Shockproof and ergonomic control panel with oil-resistant EPDM cover • Top access to the saw, material and feed unit • Hinged safety cover • Fine feed adjustment • Semi-auto. Cut! • Optimize work processes with CNC control Possibility to enter various parameters such as quantities and material lengths, automatic calculation of the cutting channel • CNC control for 10 different saw programs with 99 sub-programs for different lengths and quantities, e.g. 1 cutting program with various section lengths • Automatic feed unit (CNC) via ball roller spindle incremental feed with automatic length compensation. Adjustable for section lengths of 2 mm to 9,999 mm, remainder length 170 mm.

Condition: new, 900 mm 900 mm 900x900 mm saw band length 9300 x 67 x 1,1 mm table height 790 mm band speed 14 - 60 m/min total power requirement 11 kW weight of the machine ca. 8,45 t dimensions 4,485 x 1,68 x 3,15 m The semi-automatic, hydraulic saws from the X-tech line offer the best Saw technology and best performance when cutting special steels • The electro-welded machine frame and the steel saw frame meet requirements all cutting needs and eliminate vibration and noise. • The chip conveyor is hydraulically driven and the speed is adjustable • All movements of the machine (saw frame, vice, feed, Saw band guides) are carried out thanks to modern linear guides with high static and dynamic load performance, which also has very low sliding friction to guarantee. • Another characteristic feature is the roles for the Positioning of the material by a hydraulic motor are driven. They move at right angles to the material, and thus allowing optimal clamping of the material. • Thanks to the height control of the saw band position, the operator can place the band in place near the top edge of the material. After the cut is finished, the tape automatically raised back to the previous position. Alternatively you can also “Remain” can be selected in the lower position. During the The software compares the cutting load with the cutting cycle Default. This means that the sawing system can be stopped in the event of irregularities become. • The saw band is cleaned by two adjustable steel brushes. The drive takes place hydraulically. • The hydraulic unit including filter and pressure gauge guarantees one particularly quiet operation at constant pressure. • Finely ground carbide inserts that clamp the saw blade, complete with lateral, hardened and adjustable guide rollers. The adjustable one The tape guide automatically moves as close as possible to the material. • The saw band is tensioned via a hydraulic cylinder, which is carried out by the Machine software is controlled. The voltage is set according to a given Time automatically delimbed when the machine is idle or after a cycle has been carried out. • Automatic version with CNC control in the X-TECH 900 / 1200 models a feed length of 500 mm for the series for high production rates. • The material is carried by a table with seven rollers. These will driven by a hydraulic orbital motor through which the material can be placed precisely even under maximum load. • All guided movements are carried out by four recirculating ball guides with one high capacity for static and dynamic loading; strong reduced feed friction. Tempered and ground prismatic Fgedpfxofg E Hps Ag Rsa Guides. Price on request.

Condition: new, capacity 90 degrees: round 255 mm capacity 90 degrees: square 240 mm 300 x 180 saw band length 2.765 x 27 x 0,9 mm mm table height 870 mm band speed 18 - 110 m/min total power requirement 1,5/1,8 kW weight of the machine ca. 0,63 t dimensions of the machine ca. 1,8 x 1,85 x 1,85 m Miter band saw, fully automatic GBS 250 Super VA-I MPS • Miter left. 45° automatic operation • Miter left. 60° semi-automatic operation (cuts without programming) • Shockproof and ergonomic control panel with oil-proof EPDM cover a. • Material height sensor c. (Automatic cut start detection) • Frame and gearbox made from one piece, very quiet cutting and very low vibration • Chip tray can be removed (disinfection) • Easy access to the saw, material and feed unit • Foldable safety cover Fgjdpjd Iip Aofx Ag Rea • Fine feed adjustment • Semi-automatic. Cut! Saw automatically with microprocessor control Adjustable for 2 program levels Semi-automatic operation Fully automatic operation Start after entering the desired number and length: material cut- Cutting execution and piece counting until the program is fulfilled • MPS control for entering the desired number of feeds • All important machine data is shown on the LED display during the Cutting process displayed (power consumption, cutting time, number of pieces) • The entered data is in RAM memory • The autodiagnostic circuit automatically shows all irregularities as an error message and checks the entire process • Feed unit mounted floating. • Length adjustment via handwheel and vernier with mechanical position indicator. Adjustable for section lengths from 2.5 mm to 420 mm or through Automatic reversing can be repeated 1 - 29 times, remaining piece length 210 mm

Condition: new, capacity 90 degrees: round 305 mm capacity 90 degrees: square 260 mm 350x200 Fedpfeupw R Aex Ag Rega saw band length 3375x27x0,9 mm band speed 18 - 100 m/min table height 880 mm total power requirement 1,5/1,8 kW weight of the machine ca. 0,84 t dimensions of the machine ca. 1,85 x 1,9 x 2,0 m Demonstration system for a SPECIAL PRICE!! Fully automatic miter band saw • miter left 45° automatic operation • miter left 60° semi-automatic operation (cuts without programming) • Material height sensor (automatic cut start recognition) • Frame and gear made from one piece, very quiet cut and very low vibration • Removable chip tray (disinfection) • Shockproof and ergonomic control panel with oil-resistant EPDM cover • Top access to the saw, material and feed unit • Hinged safety cover • Fine feed adjustment • Semi-auto. Cut! • Optimize work processes with CNC control Possibility to enter various parameters such as quantities and material lengths, automatic calculation of the cutting channel • CNC control for 10 different saw programs with 99 sub-programs for different lengths and quantities, e.g. 1 cutting program with various section lengths • Automatic feed unit (CNC) via ball roller spindle incremental feed with automatic length compensation. Adjustable for section lengths of 2 mm to 9,999 mm, remainder length 170 mm. Inclusive: - Micro-spray device - Leveling elements

Condition: new, capacity 90 degrees: round 310 mm capacity 90 degrees: square 280 mm 400x250 saw band length 4020x34x1,1 mm band speed 37 + 74 m/min Fedpfx Ajd Iiptjg Roga table height 940 mm total power requirement 1,8/2,2 kW weight of the machine ca. 0,68 t dimensions of the machine ca. 1,5 x 1,78 x 1,3 m ACTION PRICE !!! Double miter band saw, hydraulic semi-automatic, GBS 310/400 HA-I Easy • miter left 60° + right 45° • Industrial hydraulics, powerful 18 bar • Best access to the material • Ammeter to check a. - Optimization of cutting force - Tape life - cutting course • Vise closes/opens hydraulically • Chip removal brush • Material turntable with ball bearings b. • Adjustable quick-release c. • Material height sensor (automatic cut start detection) Semi-automatic function: 1. Clamp material 2. Saw starts 3. Rapid lowering to the start of the material or the same for series cutting cut 4. Saw band off 5. Raise the frame to just above the material 6. Open the vise

Condition: new, capacity 90 degrees: round 250 mm capacity 90 degrees: square 210 mm 290 x 210 mm saw band length 2.965 x 27 x 0,9 mm mm table height 940 mm band speed 35 / 70 m/min total power requirement 1,1/1,3 kW weight of the machine ca. 0,35 t dimensions of the machine ca. 1,3 x 0,8 x 1,5 m SPECIAL PRICE!!! Double miter metal band saw hydraulic semi-automatic with: - Hydraulic vice - Material height button - Cut monitoring by ammeter - Cutting pressure feed regulator - Belt speed 34 / 74 m/min Fodpfxed Iip Rs Ag Rjga - Miter cuts up to 60° left and 45° right - Patented, ball-bearing turntable for easy miter adjustment - Adjustable quick-release vise - Quick release lever - Automatic cooling Share of freight costs 120 EUR

Condition: good (used), functionality: fully functional, – Length 420 cm Fodoyxx H Tspfx Ag Roga – Emergency stop – Documentation – 230V

Condition: used, Year of construction: 1997, Working Range (Square): 360 x 360 mm Cutting Speed: 16 - 210 m/min Smallest Material Dim.: 10 x 15 mm Min. Cut-off Length: 8 mm Remnant Length (Automatic): approx. 130 mm Remnant Length (Manual): approx. 40 mm Infeed: 3m Infeed roller conveyor Outfeed: 2m Outfeed roller conveyor Fgodsyxh Tpjpfx Ag Rea Chip Conveyor: High-type chip conveyor Saw Drive Power: 3.5 / 5.5 kW

Condition: used, Year of construction: 2008, functionality: fully functional, ATTENTION!: The machine is back on the market due to the buyer’s cancellation. Dismantling of the old machine will begin on November 12, 2025, as the new machine is being delivered. Bandsaw Machine for Processing Large Steel Plates The machine can operate in two different directions: - Across the width of the material: the plates are pushed into the saw frame. - Along the length of the material: the saw blade is rotated 45°, and the saw frame travels along the plate. Sawing Capacities in Manual Operation: - Maximum cutting height with band control: 360 mm (14.2") - Maximum cutting height without band control: 420 mm (16.5") - Cutting height with pressure roller: 280 mm (11.0") - Minimum cutting width: 10 mm (0.4") - Maximum cutting width: 2,000 mm (78.7") - Maximum cutting length: 7,000 mm (275.6") Sawing Capacities in Automatic Operation: - Maximum cutting height (standard): 250 mm (9.8") - Maximum cutting height (option): 350 mm (13.8") - Minimum trimming width: 10 mm (0.4") - Maximum trimming width: 2,000 mm (78.7") - Maximum cutting length: 7,000 mm (275.6") Bandsaw Speed: Infinitely variable - Standard: 13 – 130 m/min (42.6 – 426.5 ft/min) - 14 – 75 m/min (45.9 – 246 ft/min) - Option: 12 – 120 m/min (39.3 – 393.7 ft/min) Feed Rate: Infinitely variable - 0.5 – 250 mm/min (0.02" – 9.8"/min) Bandsaw Blade Dimensions: Fodpfx Agexvqr Tj Rega - 9,754 x 54 x 1.3 mm (384" x 2.1" x 0.05") or - 9,754 x 54 x 1.6 mm (384" x 2.1" x 0.06") Kerf: 2.1 mm (0.08") Bandsaw Guide: Carbide, replaceable and adjustable Back-guide for bandsaw blade: Carbide strips, replaceable Bandsaw cleaning: Via easily replaceable, driven plastic brush Option: Automatic adjustment Machine Dimensions: - Length approx.: 11,500 mm (346.4") - Width (with door open) approx.: 8,800 mm (346.4") - Height (with laser lamp) approx.: 4,080 mm (160.6") - Working table height: 1,825 mm (71.8") - Approx. weight: 25,000 kg (55,116 lbs) Total power consumption: approx. 28.0 kW (37.5 HP) Saw motor output: approx. 7.5 kW (10.0 HP)

Condition: used, Year of construction: 1998, cutting diameter / mm saw band length / mm cutting width / mm KASTO SBA 280 AU-CC band saw Fgsdpfjyvkv Ujx Ag Rsa Cutting capacity: 5 kW Machine weight: 1,750 kg Year of manufacture: 1998 Note: The display is not functioning properly and dims during operation.

Condition: used, capacity 90 degrees: round 260 mm capacity 90 degrees: square 260 mm capacity 90 degrees: flat 300 x 260 mm dimensions of saw-band 4200 x 34 x 1,1 mm sawing motor 4 kW In our opinion, the machine is in good used condition and can be inspected under power by appointment. Fjdpjyukhmofx Ag Rjga Accessories, tools and clamping devices shown are only included in the scope of delivery if this is noted in the additional information. Subject to changes and errors in the technical data and information as well as prior sale!

Condition: used, Year of construction: 2015, saw blade diameter 350 mm Cutting capacity 90° (rectangle) 100 x 90 mm Cutting capacity 90° (square) 90 x 90 mm Fgodpoygx Dyjfx Ag Rea Cutting capacity 90° (round) Ø 95 mm Cutting capacity 45° (rectangle) 75 x 80 mm Cutting capacity 45° (square) 75 x 75 mm Cutting capacity 45° (round) Ø 90 mm spindle turning speed range 38/19 U/min power capacity 1,5 / 0,75 kW In our assessment, the machine is in good used condition and can be inspected under power by appointment. Accessories, tools, and clamping devices shown are only included in the scope of delivery if this is noted in the additional information. Technical data and specifications are subject to change without notice and errors. Prior sale is reserved.

Year of construction: 1999, condition: ready for operation (used), An automatic single-head underfloor saw Emmegi including a chip extraction system is available. Cutting angle: 90°, feed travel: 0mm-1000mm, positioning accuracy: +/-0.5mm, saw blade diameter: 500mm, motor power: 6.6kW, weight: approx. 1000kg. An on-site inspection is possible. Fodpjyz Apqofx Ag Rega

Condition: used, Model: USF-8 SPEZ Serial No: 37531 Capacities: Throat Depth: 810mm Height Under Blade Guide: 550mm Table: 1480 x 1220mm Table Traverse: 1000mm Feeds: Variable Speeds Variable: 12 – 3000 Rpm Blade Size: 6550 x 38mm Complete With: Operators Consul Laser Alignment Coolant Fgjdpfx Ageydv R Ej Rja Hydraulic Blade Tensioning Approximate Dimensions: 2400 x 2400 x 3750mm Approximate Weight: 1500kg

Condition: excellent (used), Year of construction: 2023, functionality: fully functional, machine/vehicle number: 1587 / 1588, saw blade diameter: 500 mm, This model combines precise cutting to length with integrated punching operations, making it ideal for complex manufacturing processes: Saw unit: Equipped with a saw blade diameter of 500 mm. Drive is provided by a 7.5 kW motor (400 V) with stepless speed control. Punching unit: Features a hydraulic punching unit on the cut-off side with a punching force of 250 kN. The punching direction is vertical from above, with punching tool cassettes that can accommodate up to 8 profiles simultaneously. Material feed: The feed is controlled via a ball screw spindle and a servomotor, with a maximum feed length of 400 mm per individual stroke. Control system: Modern variants often use a Siemens S7 control with touch display for intuitive operation and precise programming. The machine is designed for continuous industrial operation and has the following physical characteristics: Weight: approx. 1,000 kg to 1,500 kg (depending on configuration). Dimensions (saw): approx. 2,100 x 2,000 x 1,600 mm (LxWxH). Hydraulic unit: approx. 900 x 600 x 800 mm. 2 machines in stock. ----- Attractive offer – flexible & worry-free We not only offer you a high-quality product, but also tailor-made financing options to suit your needs. Whether down payment, installment plan or individual financing models – together we will find the right solution. Upon request, we will also handle the complete transport logistics. From planning to reliable delivery, we ensure a smooth and punctual process so you don't have to worry about a thing. Fgjdpeyyz Txjfx Ag Rja 📞 Please contact us for more information or a non-binding quote. We provide you with personal and knowledgeable advice. Subject to prior sale, changes and errors excepted!

Condition: used, Working mode: semiautomatic Machine type: Horizontal bandsaw Cut: Mitre cut Fedpfxsydp Udj Ag Rjga Mitre cuts range: -60° – 60° Drive: 4 kW, 3×400 V/50 Hz Saw band speed: 20 – 120 m/min. Saw band dimensions: 6 100×41×1,3 mm Material loading height: 770 mm Shortest remnant length: 40 mm Smallest sawing diameter: Ø 5 mm