Year of construction: 1973, condition: like new (used), Used BRONX Heavy Duty Initial Pinch Pyramid bending rolls. Year of manufacture : 1973. MACHINE FORMERLY INSTALLED AT ROLLS ROYCE PLC IN DERBY UK. IMMEDIATELY FOR SALE AND NOW LOCATED IN BELGUIM WHERE IT CAN BE INSPECTED. SPECIFICATION CAPACITY Two sets of dimensions which are shown below as "Prebending & Rolling" and then "Rolling only". Material Mild Steel Mild Steel Tensile strength 28/32 tons/sq.in 28/32 tons/sq.in Maximum width 11’(3350mm) 11’(3350mm) Maximum thickness at this width 2” (50mm) 2½” (63.5mm) Minimum inside diameter of rolled cylinder at maximum capacity 30’ (762mm) 37 ½’ (953mm) Maximum thickness of plate when hot rolling (finished rolling temperature 850° C.) 4” (102mm) 5” (127mm) Minimum inside diameter of rolled cylinder at maximum capacity hot rolling 40” (1016mm) 50” (1270mm) MAIN PARTICULARS Diameter of all rolls - 27” (686mm) Body length of rolls - 11’2”(3403mm) Rolling speed - 12 f.p.m. (3600mm/min) Main drive motor - 150 H.P. Slip Ring Type Two bottom roll adjusting motors, each - 50 H.P. Slip Ring Type Combined operation of swing down bearing and top roll counterbalance - Hydraulically applied Hydraulic power pack motor - 10 H.P. Electrical equipment to be suitable for operation on a supply of - 400/440 volts, 3 phase, 50 cycles CONE ROLLING ATTACHMENT: To facilitate the rolling of taper or conical forms, a skid plate is fitted to the inside of the non-drive end housing. ELECTRICAL EQUIPMENT Motors: Main Drive - 150 H.P. half hour rated – slip ring screen protected – foot mounted type. Bottom Roll Adjustments - 50 H.P. half hour rated – slip ring screen protected – foot mounted type. Hydraulic Power Pack Motor - 10 H.P. continuously rated – Squirrel cage – screen protected – foot mounted type. Control Gear: Kjdpfxeh U Rzgj Ag Njdu Main Drive - Drum type reversing control gear with 5 minute rated wire wound resistances, designed to pass 100% full load on the first notch or operating position in each direction. The controller will be fitted with off position interlock and limit switch rings where necessary. Bottom Roll Adjustments - Drum type reversing control gear with 5 minute rated wire wound resistances designed to pass 100% full load on the first notch or operating position in each direction. The controllers will be fitted with off position interlock and limit switch rings where necessary. Hydraulic Power Pack - Direct-on-line contactor type starter, operated from a maintaining type push button station. Solenoid valves for operating cylinders are push button operated. Note: Full protection to be provided for all the above control gear by a circuit breaker, incorporating overload and no-volt protection. FEATURES AND EQUIPMENT Spare Roll included with the machine. LENGTH TBA MM WIDTH TBA MM HEIGHT TBA MM WEIGHT 95 tonnes NOTE: The information contained herein is provided in good faith, but however due to unforeseen errors or omissions cannot be binding as to accuracy.

Condition: used, OKK HM 40 , 400mm HMC, (8) Pallets, serial number 378 MA74294, 16 i M Fanuc Control, BT 40 Spindle, 20,000 RPM, 120 ATC, B axis, Through Spindle Coolant, Coolant & Chiller, NEW 2001. Kdodpfxjxpxp Ho Ag Nsu

Condition: excellent (used), Year of construction: 2017, Excellent Condition Table Diameter - 320mm Max Workpiece size - 400 x 300mm Table loading capacity - 200kg T-slot size - 12 x 90 Kdsdpsxmhbaefx Ag Nou Travel X/Y/Z - 400/650/485mm Distance from spindle nose to table top - 0-485mm A axis travel (rotate along with X axis) +30 degree C Axis travel (rotate along with Z axis) 360 degree Spindle Spindle speed - Direct drive 12,000rpm Spindle taper - BT40 Spindle motor (cont./30min) - 11/15kW Spindle max. torque (cont./30min) - 70/95Nm Feedrate Linear guideway on X/Y/Z axis - Ball way 35/45/45 mm Rapid Traverse rate on X/Y/Z axis - 36,000 / 24,000 / 10,000mm/min Rapid traverse rate on A/C axis - 20/27rpm Cutting feedrate - 10,000mm/min Tool Magazine Tool Magazine - 24 pocket Max tool diameter / adjacent pocket empty - 80mm Max tool length - 300mm Max tool weight - 8kg Space requirement & weight Machine length x width 2950 x 2350mm Machine height 3140mm Machine weight 7200kg CNC Control - Fanuc 0MP Miscellaneous Pneumatic requirement - 6kg/cm power requirement - 40KVA coolant tank capacity - 400ltr

Condition: used, Year of construction: 2016, functionality: fully functional, travel distance X-axis: 450 mm, travel distance Y-axis: 600 mm, travel distance Z-axis: 330 mm, rapid traverse X-axis: 30 m/min, rapid traverse Y-axis: 30 m/min, rapid traverse Z-axis: 30 m/min, controller manufacturer: Siemens, controller model: 840D, workpiece height (max.): 370 mm, table width: 320 mm, table length: 320 mm, table load: 300 kg, rotational speed (min.): 80 rpm, rotational speed (max.): 80 rpm, overall weight: 9,000 kg, spindle speed (min.): 15,000 rpm, spindle speed (max.): 15,000 rpm, spindle motor power: 31 W, spindle nose: HSK 63A, tool length: 250 mm, tool diameter: 125 mm, tool weight: 8 g, control type: CNC control, Equipment: chip conveyor, Hermle C22U 5 Axis Machining Centre Siemens 840D Control 5 Axis Simultaneous Kdodpfx Agexpil So Nou XYZ: 450 x 600 x 330mm 320mm diameter table Maximum workpiece diameter 320mm maximum workpiece height 265mm Maximum table load 300Kg A axis -/+ 135 degrees spindle speed 15,000rpm 55 station tool changer Swarf Conveyor Coolant Tool Setter Spindle Probe

Condition: used, Year of construction: 1996, MAZAK SUPER QUICK TURN 10 MS CNC LATHE MAKE MAZAK, MADE IN JAPAN MODEL SUPER QUICK TURM 10 MS YEAR 1996 CONTROL MAZATROL T PLUS MAX SWING 435mm SWING OVER CARRIAGE 370mm MAX. MACHINING DIA 230mm MAX. BAR WORK DIA 42mm MAX DISTANCE BETWEEN SPINDLES 705mm SPINDLE MOTOR AC11kw (15HP) SPINDLE SPEED 6000rpm Ksdpsxnpp Iefx Ag Nodu 2ND SPINDLE MOTOR AC5.5kw (7.5HP) 2ND SPINDLE SPEED 6000 rpm ROTARY TOOL MOTOR AC2.2kw (3HP) ROTARY TOOL SPEED 3000 rpm TURRET TOOL CAPACITY 12 TOOLS STATIONS RAPID TRAVERSE RATE X,Z:30m/min (1180IPM),C: 400rpm MACHINE DIMENSION L x W x H, 2705mm x 1465mm x 1835mm MACHINE WEIGHT 3850kg PLUS C-AXIS SUB SPINDLE DRIVEN TOOLS (3 NO.S) PARTS CATCHER SWARF CONVEYOR TOOL SETTING PROBE COLLET CHUCK BUILT IN TRANSFORMER FULL SET OF MANUALS GOOD WORKING ORDER

Condition: good (used), Ecoca MT-312/750 CNC Lathe FANUC 21iTB, 12″ Chuck, 2006 Year: 2006 Control: FANUC 21iTB Chuck Size: 12″ (305 mm) – 3-Jaw Swing Over Bed: 600 mm Swing Over Cross Slide: 330 mm Max Turning Diameter: Over Bed: 450 mm (17.7″) Over Cross Slide: 330 mm (12.99″) Kdsdpfx Agsxpnl Do Nou Z-Axis Travel (Turning Length): 730 mm (28.74″) Spindle Power: 24.8 HP (18.5 kW) Spindle Speed: Up to 3,200 RPM Tool Turret: 12-station Tailstock: Included Tool Arm: Included

Condition: like new (used), Year of construction: 2020, operating hours: 1,500 h, functionality: fully functional, USED Akira Seiki 1600XP Fanuc 0iMF Open Fronted Vertical Machining Centre with Fanuc Ex Stock - Subject to Prior Sale. YOM 2020, Machine with Very Low Hours Usage. Approx 1500 Hours  12,000 RPM Spindle with Refrigeration System  36 Station Arm Type ATC Ksdpfsq Nmm Tox Ag Nsdu  Full Splash Guard  Fully Integrated Detron GXA-255h 4th Axis Nc Rotary Table with SR255H Tailstock Support Unit  Chip Conveyor & Chip Bin (Scraper Type)  Chip Flushing System Including Coolant Wash Gun  Through Spindle Coolant System - 35 Bars with Filter  Fanuc Memory Extension - 2 Mb  Fanuc 10.4 “ Screen with Manual Guide-I  Coolant Tank Capacity - 640 Litres  THK Heavy Duty Linear Guideways  Manual Pulse Generator  3 Colour Signal Lamp  Automatic Lubrication System  Rigid Tapping & Helical Interpolation Function TABLE Working Surface 1,750 X 800 MM Tee Slots 18 x 125 x 6.0 MM Spindle Nose to Table 100 ~ 915 MM Spindle Centre to Column 865 MM Table Load Capacity 2,300 KGS TRAVEL X-Axis Travel 1,630 MM Y-Axis Travel 850 MM Z-Axis Travel 815 MM SPINDLE Spindle Nose Taper BT-40 Spindle Speed - Max 12,000 RPM FEED Rapid Traverse (X & Y-Axis) 33 M / MIN Rapid Traverse (Z-Axis) 25 M / MIN Cutting Feedrates - Max 12 M / MIN ACCURACIES Positioning 0.01 MM Repeatability + - 0.003 MM ATC Tool Storage Capacity ARM TYPE - 36 STATIONS Maximum Tool Weight 7.0 KGS Tool Diameter - Max 75 MM Tool Length - Max 250 MM Tool Shank BT-40 Tool Exchange Time 2.2 SEC MOTOR Spindle Drive Motor (FANUC) 18.5 KW POWER SUPPLY Voltage 415V / 3PH / 50HZ Power Requirement 30.0 KVA MACHINE DIMENSIONS Machine Floor Space Requirement 4,820 x 3,576 MM Machine Weight 12,600 KG

Condition: used, machine/vehicle number: L2SIH0236, turning diameter over cross slide: 700 mm, turning length: 1,500 mm, spindle bore: 80 mm, Leadwell LTC 30 BPL, CNC Turning Centre with Fanuc OT Control, fitted with 300mm dia 3 jaw chuck Made in Japan, approx 700mm swing x 1500mm centre distance, spindle bore 80mm,  operators foot pedal, Serial Number L2SIH0236, swarf conveyor, Kdjdpfx Asw A Rqrjg Nsu

Condition: excellent (used), Year of construction: 1982, Model D.I. + M.I.A Max width of wheel 250mm/10" Min width of wheel 30mm / 1 1/4" Kdodjw Svrrepfx Ag Nju Wheel diameter 508mm Horsepower 30 HP Weight 5900kg Year 1982 Manuals & electrical diagrams included

Condition: used, Year of construction: 2012, machine/vehicle number: MB0001-000031, travel distance X-axis: 2,000 mm, travel distance Y-axis: 1,500 mm, travel distance Z-axis: 1,200 mm, rapid traverse X-axis: 12 m/min, rapid traverse Y-axis: 12 m/min, rapid traverse Z-axis: 12 m/min, feed length Y-axis: 6 mm, feed rate X-axis: 6 m/min, feed rate Y-axis: 6 m/min, feed rate Z-axis: 6 m/min, controller manufacturer: FANUC, controller model: 32i Model A, workpiece diameter (max.): 2,550 mm, workpiece weight (max.): 7,000 kg, total height: 4,200 mm, total length: 5,540 mm, total width: 5,930 mm, table width: 1,400 mm, table length: 1,600 mm, overall weight: 29,000 kg, spindle speed (max.): 3,000 rpm, distance table center to spindle nose: 1,750 mm, spindle motor power: 26 W, spindle nose: BT50, number of slots in tool magazine: 60, tool length: 600 mm, tool diameter: 250 mm, tool weight: 30 g, B Axis: 1 degree Control: FANUC 32i-Model A Distance from Spindle Nose to Table Top: 0 - 1500mm Distance from Spindle Nose to Table Centre: 550 - 1750mm Machine Dimensions: 5540 x 5930 x 4200mm Machine Weight: 29000kg Maximum Cutting Feedrate: 6m/minute Maximum Tool Diameter: 250mm Maximum Tool Length: 600mm Maximum Tool Weight: 30kg Maximum workpiece weight: 7000kg Rapid Feedrates: WXYZ: 6 x 12 x 12 x 12m/minute Spindle Diameter: 110mm Kedpfxexm Sxvs Ag Nodu Spindle Motor Power: 26/22kW Spindle Speed: 3000rpm Swing: 2550mm Table Size: 1400 x 1600mm Tool Change Capacity: 60 Station Tool Size: BT50 Traverses XYZ: 2000 x 1500 x 1200mm W Axis: 500mm Coolant, Low Volt Light, Swarf Conveyor, Long Reach Right Angled Milling Head, Tool Length Measurement Probe, Renishaw Work Probe, Fully Enclosed machine guards.

Condition: used, Year of construction: 2014, 2014 built Hurco VM30i with single MAX screen Hurco Control. Note: Photographed on Site...more pictures to follow when the machines arrive in Bristol. Fitted with Max control, 10,000 RPM BT40 spindle. In super condition given their age! . Kdedowzlupopfx Ag Neu Specification: X Axis stroke mm 1.270 Y Axis travel mm 510 Z Axis stroke mm 510 Spindle nose to table surface mm 100-610 T slot (WxDxN) mm 5x18 Working table area (LxW) mm 1.320x510 Spindle Speed rpm 10.000 Main motor kw 15 Motor torque Nm 102 X/Y/Z Axis cutting feedrate mm/min 24/ 24/ 24 Pull stud SK40 Tool storage capacity pc 20 Max. Tool Diameter mm 89 Max. Tool Length mm 250 Max. Tool Weight Kg 7 Machine weight Kg 4.245 Floor space (LxWxH) mm 4.083x2.743x2.576 Standard configuration Control: WinMax Spindle 10.000 RPM Swing arm type 20 tool ATC Pocket and island milling Rigid tap and tapping Remote Jogbox

Condition: excellent (used), Dugard Mini Mill CNC Vertical Machining Centre Fanuc Oi, 4th Axis, 2011 Year: 2011 Model: MN965005 Control System: Fanuc Oi-MB Kdedpfsxpnlqsx Ag Neu X-Axis Travel: 450 mm Y-Axis Travel: 350 mm Z-Axis Travel: 380 mm Table Size: 700 × 320 mm Max Table Load: 150 kg Spindle Speed: 80–8,000 RPM Spindle Taper: BT‑40 Spindle Motor: Fanuc Version: 5.5 kW Siemens Version: 8.5 kW (specify if applicable) Toolchanger: 12-position Automatic Tool Changer 4th Axis: Included Rapid Feed Rate: 36 m/min Working Feedrate: Up to 10,000 mm/min

Condition: like new (used), Year of construction: 2020, operating hours: 1,500 h, functionality: fully functional, USED Akira Seiki 1600XP Fanuc 0iMF Open Fronted Vertical Machining Centre with Fanuc Ex Stock - Subject to Prior Sale. YOM 2020, Machine with Very Low Hours Usage. Approx 1500 Hours  12,000 RPM Spindle with Refrigeration System  36 Station Arm Type ATC  Full Splash Guard  Fully Integrated Detron GXA-255h 4th Axis Nc Rotary Table with SR255H Tailstock Support Unit  Chip Conveyor & Chip Bin (Scraper Type)  Chip Flushing System Including Coolant Wash Gun  Through Spindle Coolant System - 35 Bars with Filter  Fanuc Memory Extension - 2 Mb  Fanuc 10.4 “ Screen with Manual Guide-I  Coolant Tank Capacity - 640 Litres  THK Heavy Duty Linear Guideways  Manual Pulse Generator  3 Colour Signal Lamp  Automatic Lubrication System  Rigid Tapping & Helical Interpolation Function TABLE Working Surface 1,750 X 800 MM Tee Slots 18 x 125 x 6.0 MM Spindle Nose to Table 100 ~ 915 MM Spindle Centre to Column 865 MM Table Load Capacity 2,300 KGS TRAVEL X-Axis Travel 1,630 MM Y-Axis Travel 850 MM Z-Axis Travel 815 MM SPINDLE Spindle Nose Taper BT-40 Spindle Speed - Max 12,000 RPM FEED Rapid Traverse (X & Y-Axis) 33 M / MIN Rapid Traverse (Z-Axis) 25 M / MIN Cutting Feedrates - Max 12 M / MIN ACCURACIES Positioning 0.01 MM Repeatability + - 0.003 MM ATC Tool Storage Capacity ARM TYPE - 36 STATIONS Maximum Tool Weight 7.0 KGS Tool Diameter - Max 75 MM Tool Length - Max 250 MM Tool Shank BT-40 Ksdou A U Nkjpfx Ag Nodu Tool Exchange Time 2.2 SEC MOTOR Spindle Drive Motor (FANUC) 18.5 KW POWER SUPPLY Voltage 415V / 3PH / 50HZ Power Requirement 30.0 KVA MACHINE DIMENSIONS Machine Floor Space Requirement 4,820 x 3,576 MM Machine Weight 12,600 KG

Condition: excellent (used), Year of construction: 2016, XYZ 1550VS Gap Bed Centre Lathe EX Training College Machine 3 Jaw Chuck 2-axis Digital Readout Toolpost & Chuck Guard Footbrake (Modern Triumph 2000 size machine Manufactured & Installed 2016 Machine Capacity: Swing Over Bed 390mm Swing in Gap 610mm Swing Over Cross Slide 150mm Distance Between Centres 1250mm Cross Slide Travel 230mm Kedsxn Sf Sepfx Ag Nsdu Spindle: Spindle Speeds 20 – 2500rpm Spindle Power 5.75kW Spindle Bore 54mm Spindle Nose D1-6 For sale with Jet Machinery Ltd Jet Machinery Stock No: #79010 Machine Serial Number: 7715 Cost: £9,950.00 + VAT Whilst every effort has been made to ensure that the above information is accurate it is not guaranteed. We advise prospective purchasers to check any vital details. Health and Safety At Work Act 1974: It is not reasonably practical for ourselves as suppliers to ensure that for your application the goods comply with requirements of the Act with respect to guarding etc. Prospective purchasers should ensure that a guarding specialist inspect the goods prior to use.

Condition: used, functionality: fully functional, We currently have a Roundo bending machine available for sale. This machine is capable of bending large-size wide-flange beams — even when cold — into radii or cambered shapes. It is a robust and versatile unit, ideal for companies looking to enhance or expand their steel-forming capabilities. Kdodpexn I Rwefx Ag Nou

Condition: good (used), Year of construction: 2015, Swing over bed 720mm, maximum machining diameter 420mm, maximum machining length 1274mm, bar capacity 77mm, spindle speed 4,000rpm, milling speed 4,000rpm, 12 station turret, Mazatrol smart control, Ksdpfxovgz D Ee Ag Nsdu swarf conveyor, parts catcher, tool setter, and 3 jaw chuck, magazine barfeed unit.

Year of construction: 2024, operating hours: 15 h, condition: like new (used), functionality: fully functional, Imported from china to the uk 2025. Upgraded power, control and control panel wiring to UK/Eu specifications. Brand new and comissioned. fully automated and fully adjustable output to a maximum of 15meters per minute. Saftey pull cord and E stop system installed Kdodpfexl U Scex Ag Neu

Condition: excellent (used), Harrison Alpha 1550 XS Manual / CNC Lathe Year: 2018 Kodoxpnk Tjpfx Ag Nodu Control: FANUC Oi-TF Swing Over Bed: 554mm Swing Over Cross Slide: 370mm Swing in Gap: 830mm Distance Between Centres: 2000mm Spindle Bore: 104mm dia. Spindle Speeds: 1 to 2000 RPM Quick Change Toolpost Boring Bar attachment

Condition: used, Year of construction: 1989, Studer Type S40-4 CNC Cylindrical Grinder with Studer Siemens Control, Centre Height 225mm, Centre Distance 1600mm, Wheel Head Slide Max Travel 275mm, Marpass E39 Gauge, Wheel Size 400mm x 80mm x 127mm, Speeds 2 100rpm, Filter Mist. S/No. 7234.22 (1989). Country of Origin: Switzerland A charge of £750 for dismantling and loading onto suitable transport will be automatically added to your invoice should you be successful in purchasing this item. Blocking and securing will be at the cost of the purchaser. Kdodpfexnlg Nsx Ag Nou Please Note: This lot is located in Birmingham, UK

Condition: excellent (used), Year of construction: 2014, XYZ 1020 Vertical Machining Centre Siemens 828D Control Manufactured & Installed in 2012 24 Station Too Carousel 8k Spindle Kdodoxndrdepfx Ag Nou Machine Capacity: Table Size: 1120 x 500 X Axis Travel 1020mm Y Axis Travel 520mm Z Axis Travel 540mm Rapid Traverses 20,000m/min Spindle: Spindle Speeds – 8,000ppm Tool Shank ISO40 Tool Storage Capacity 24 Tools Spindle Power 20Hp For sale with Jet Machinery Ltd Machine Serial Number: SMU00143 Cost: £27,500.00 + VAT Whilst every effort has been made to ensure that the above information is accurate it is not guaranteed. We advise prospective purchasers to check any vital details. Health and Safety At Work Act 1974: It is not reasonably practical for ourselves as suppliers to ensure that for your application the goods comply with requirements of the Act with respect to guarding etc. Prospective purchasers should ensure that a guarding specialist inspect the goods prior to use.  

Condition: good (used), Year of construction: 2007, Used CNC lathe from Doosan Type: Lynx 220 Turning diameter: 250 mm Turning length: 550 mm Spindle bore: 51 mm X and Y axes 12-position tool turret Fanuc CNC control Kdedpfx Aexpxb Asg Nou LNS bar feeder

Condition: good (used), Year of construction: 2008, Traverses X Y Z: 3000 x 1300 x 2000mm, Table 2000 x 1600mm, table load 13,000 kgs, B axis 360 degrees, Kdsdevz A Rispfx Ag Nou Heidenhain iTNC530, ISO SK50 spindle taper, 5,000rpm Spindle Speed, 60 station toolchanger, coolant, Interlocked guards.

Condition: ready for operation (used), Year of construction: 2017, operating hours: 10,493 h, General Data Machine weight 15000 kg Kdjdpfoxpyn Dox Ag Nju Control Unit Brand MAZATROL Model Smooth Main Drive Number of axis 5 Movement X-Axis Movement 630 mm X-Axis Rapid Traverse 60 m/min Y-Axis Movement 1100 mm Y-Axis Rapid Traverse 60 m/min Z-Axis Movement 600 mm Z-Axis Rapid Traverse 56 m/min A-Axis Movement -120° to +30° A-Axis Rapid Traverse 18000°/min C-Axis Movement ±360º C-Axis Rapid Traverse 18000°/min Tools Number of index 40 Additional Equipment Equipped with Multiple-Surface / Simultaneous 5-axis Machining Center capabilities Features a Knoll 640 S-1 chip conveyor and Knoll KF400 coolant pump This 5-axis Mazak VARIAXIS i-700 was manufactured in 2017. Ideal for complex and precise machining tasks, this vertical machining centre ensures efficient multi-surface processing. Consider the opportunity to buy this Mazak VARIAXIS i-700 vertical machining centre. Contact us for more information about this machine. Application Types Milling

Condition: good (used), Year of construction: 2006, Used CNC lathe from Viktor Type: VTurn II 26 Turning diameter: 520 mm X: 240 mm Z: 1250 mm Spindle: 87 mm Y-axis Kodpfoxpxafsx Ag Njdu C-axis Driven tools Hydraulic steady rest Chip conveyor

Condition: good (used), Year of construction: 2010, Bar capacity 50.8mm, maximum cutting diameter 279mm, maximum cutting length 274mm, Spindle power 11Kw, Spindle speed 6,000rpm, 12 station turret, fitted with collet chuck, tool setter and magazine barfeed unit. Kdjdpsxlch Ssfx Ag Nou