Year of construction: 1993, Condition: ready for operation (used), Max. working length: 2600mm, max. pressing force: 700kN, stroke: 8-60mm, connected load: 8kW, weight: 4.5t, with documentation. Dobvccjpcgy Asqmokl

Condition: used, Single column hydraulic press DUNKES type HZT 2,5 Machine No. H94-2558 Year of construction 1994 pressure force 2,5 ton. throat 180 mm table area 420 x 300 mm drop-through opening in table 60 x 185 mm ram surface Ø 40 mm clamping spigot bore Ø 20 mm ram stroke 160 mm Installation height max. 250 mm Rapid traverse downward 65 mm/sec. Rapid traverse upwards 160 mm/sec. Working speed 8,3 mm/sec. Table height above floor 950 mm Hydraulic operating pressure 135 bar Tank capacity hydraulics approx. 100 liters Drive power 1,5 kW Mains connection 400 Volt, 50 Hz - Installation height can be increased by shortening the piston rod by 80 mm - Pressure and travel cut-off Dkjbvccjh Uhqyoqmjl - 2-hand operation at the machine - stroke counter - safe press control with 2 monitored hydraulic valves - UVV 11.064 VGB 7.n.5.2 (for manual insertion work) - 32047 read off operating hours - Electrical circuit diagram and hydraulic diagram available space requirement L x W x H 1100 x 980 x 1950 mm weight 700 kg very good condition

Condition: good (used), Year of construction: 1995, Functionality: fully functional, machine/vehicle number: 0540/98, Manufacturing number: 0540/98. Year of manufacture: 1998 ,. Capacity: 400 tons. Stroke length: 300 mm. Stroke: 10-40 / min. Slide adjustment 300 mm. Installation height: 700 mm. The table measures 1600 x 1300 mm Net weight: 45 tons. Gable opening: 1600 mm. Dkobvceicbbzecqmjl Exterior dimensions 2 x 3 x 6 meters. Control system MEAB. Coil feeder / straightener iRON RNE 50B / 11. Decoiler iRON SA6000 max 700 mm.

Condition: ready for operation (used), Functionality: limited functionality, machine/vehicle number: 088-030 | 159, pressing force: 3 t, table width: 280 mm, table length: 280 mm, operating speed: 100 mm/s, overall weight: 370 kg, reverse speed: 300 mm/s, ram stroke: 280 mm, retraction force: 1 t, input voltage: 380 V, Manufacturer: VEB Wema Zeulenroda Dkobvccqouclhnemol Type: PYTE 3.15 Maximum pressing force: 3.15 tons Lower table: 280 x 280 mm Cylinder stroke: 280 mm Downward speed: 100 mm/sec Upward speed: 300 mm/sec Power requirement: 1.5 kW Weight: 370 kg Hydraulic press with mechanical two-hand operation or switchable to mechanical foot operation. Both operating variants act directly on the hydraulic control valve. The design is very robust and durable. The press is ready for immediate use and in good condition. With mechanical two-hand operation, both levers must be pulled in exactly the same way (see video), otherwise the press will not lower. This is why we mainly worked with the foot operation. The pressure indicator is defective and would have to be replaced if necessary.

Year of construction: 1991, Condition: ready for operation (used), Max. pressing force: 2000kN, max. working length: 2600mm, max. stroke: 265mm, throat depth: 300mm, weight: 16t. Dobvjhkdu Hsccqmjkl

Condition: used, Single-column hydraulic press SCHÖN type FES / C 7 Machine no. No. 4281 Year of construction 1995 Pressure force 7 ton. throat 170 mm Projection round cycle station 60 mm Table size 310 x 200 mm Rotary indexing table Ø 400 mm, with 12 indexing stations Plunger surface approx. Ø 100 mm Plunger plate 315 x 200 x 35 mm Ram stroke 100 mm Installation height rotary table - ram plate max. 130 mm Table height above floor 890 mm Ram speed rapid traverse downwards approx. 300 mm/sec. Ram speed rapid traverse upwards approx. 300 mm/sec. Ram speed Working speed approx. 30 mm/sec. Drive power 1.5 kW Mains connection 380 Volt, 50 Hz Tank capacity approx. 50 liters hydraulic oil - Rotary indexing control via SIEMENS S7- 1200 - GECHTER pneumatic rotary indexing table with 12 indexing stations - Mechanically adjustable fixed stop - Adjustable pressure holding time in the UT - electrical 2- manual operation Space requirement L x W x H 1450 x 850 x 1900 mm weight 700 kg Dkobvccjr I E Itoqmjl good condition

Year of construction: 1974, Condition: ready for operation (used), Working length: 3500mm, the pressure bar of the machine must be realigned. Dkebvsi Acq Rjccqmel

Condition: used, Eccentric punch press HAULICK + ROOS type RVD 125 double column - eccentric press Machine No. 212560 Year of construction 1981 pressure force 125 ton. table size 880 x 800 mm table opening 470 x 140 mm column width 900 mm column width lateral 415 mm ram stroke 45 mm slide adjustment travel 0-80 mm Installation height on the picture 340 mm Stroke rate 50 to 300 strokes/min. Motor power main drive 22 kW Mains connection 380 volt, 50 Hz - Double connecting rod drive with 4-fold eccentric shaft for off-center ram pressure load - adjacent electrical cabinet - NC roll feed EBU, width 250 mm, year 2003 - adjacent control panel for roll feed Djbvehlnzkoccqmekl - strip running direction from left to right space requirement (press) L x W x H 3000 x 2000 x 3020 mm transport height 2950 mm weight of the press approx. 11 ton.

Year of construction: 2016, Condition: ready for operation (used), Max. pressing force: 80kN, stroke: 180mm, power stroke: 12mm, weight: 760kg. Dksbvjifptysccqmel

Condition: used, Single-column eccentric press WEINGARTEN type EV 63 Machine. No. 738 / 61 Year of construction 1962 Pressure capacity 63 ton. throat 260 mm Table surface 630 x 530 mm Table opening Ø 210 mm ram surface 315 x 260 mm Plunger stroke adjustable 8-100 mm Plunger adjustment 63 mm Installation height max 450 mm Stroke rate 115 strokes / min. Compressed air requirement min. 4.5 bar Motor power 4 kW Mains connection 380 Volt, 50 Hz Table height above floor approx. 750 to 900 mm - Electric lift release via foot switch or two-hand operation - Overload protection by breaker plate - Clutch/brake combination with WEINGARTEN friction threaded clutch with TDC overrun protection - Front crankshaft support bearing - Press table height-adjustable via 2 threaded spindles - Manual central grease lubrication - Control cabinet adjacent - UVV for manual insertion work Space requirement L x W x H 1750 x 1600 x 2430 mm Weight 4.5 tons good condition Dsbvccsk S Htxeqmokl

Condition: ready for operation (used), Pressing force: 1600kN, throat depth: 450mm, installation height: 560mm, ram stroke: 8-160mm, controls: SCHMERSAL SEPG 05.3.2.0.22/ 95, weight: 16.2t, including documentation. Dkebvccjhz Ua Seqmjl

Condition: used, Single-column eccentric press WEINGARTEN type ER 63 Machine. No. 52A / 63 Year of construction 1963 Pressure capacity 63 ton. throat 280 mm Table surface 630 x 530 mm ram stroke adjustable 8-100 mm ram adjustment 63 mm Stroke rate 65 strokes / min. Motor power 4 kW Mains connection 380 Volt, 50 Hz - Clutch/brake combination with WEINGARTEN friction threaded clutch - Electric lift release via foot switch - Wheel reduction gear - Overload protection by breaker plate Dkebvccqolb I Dzjmel - Front crankshaft support bearing Space requirement L x W x H 1500 x 1100 x 2500 mm Weight 4.5 tons good condition

Year of construction: 1980, Condition: ready for operation (used), Wire diameter: 16mm, number of stations: 5, length: 6700mm, width: 3800mm, height: 3050mm, including sound-proof cabin, straightener, chain hoist, sorting trough, dosing machine, oil mist separator and additional accessories. Dksbvcceh I N Nkjqmol

Condition: used, Single column eccentric press PELS - RICHTER type PEKR 125 Dkjbvccqsfim Themel Machine. No. 20684 Year of construction 1967 pressure force 125 ton. throat 430 mm table size 1100 x 750 mm ram area 890 x 650 mm table opening Ø 400 mm stroke adjustment 6 to 115 mm ram adjustment 100 mm installation height largest stroke top max. 450 mm Clamping spigot bore Ø 50 mm Stroke rate 60 strokes/min. Table height above floor 900 mm motor power 7,5 kW Mains connection 380 Volt, 50 Hz - Overload protection by crushing plate in ram - Compressed air clutch-brake combination DESCH - ram weight balancing cylinder - manual ram adjustment - two-hand operation - cam gear - Grease central lubrication Vögele - stroke counter Space requirement L x W x H 2300 x 1450 x 3030 mm weight approx. 10 ton. good condition

Year of construction: 2013, Condition: ready for operation (used), Pressing force: 250kN, max. stroke: 160mm, working speed: 30mm, connected load: 4.7kVA, weight: 2.2t. Dkobvok Ea Uqsccqmsl

Condition: used, Single-column eccentric press WEINGARTEN type ARP 100 Machine no. No. 122481 Year of construction 1984 Pressure capacity 100 ton. throat 400 mm Table size 920 x 660 mm ram surface 700 x 450 mm Rear upright width 735 mm Stroke adjustment 20 - 160 mm Plunger adjustment 80 mm Installation height with 160 mm stroke max. 355 mm (without intermediate table top) Installation height with 20 mm stroke max. 425 mm (without intermediate table plate) Stroke rate 60 strokes/min. Table surface intermediate table top 920 x 610 mm Thickness of intermediate table top 90 mm Hole in intermediate table top Ø 210 / 180 mm Through-hole in machine table Ø 210 / 180 mm Table height above floor 800 mm (without intermediate table top) T-slot width in table and ram 22 mm Clamping pin bore 50 mm Motor power 11 kW Mains connection 400 Volt, 50 Hz - Hydraulic overload protection in ram - ORTLINGHAUS pneumatic clutch/brake combination - Electromotive ram adjustment with counter - Clamping pin bore with clamping piece - Front crankshaft support bearing - Gear reduction gears in closed oil bath gearbox - Two pneumatic tappet compensation cylinders - WOERNER automatic central grease lubrication - Lift release via electric foot switch or two-hand control panel - Electrical control cabinet permanently attached to the machine - Operating instructions and circuit diagram - UVV for manual insertion work Space requirement L x W x H 2200 x 1600 x 3250 mm Weight 8.3 tons Dobvccqju Rwa Iemskl Good condition

Year of construction: 1980, Condition: ready for operation (used), Table dimensions: 560x450mm. Dkobvccqjfz Nh Dsmsl

Condition: used, Hydr. differential stroke press, toggle lever hydraulic press, automatic punching press BRUDERER - LEINHAAS type AR 11-100.H Fine blanking press, knuckle-joint press Machine. No. P247 Year of construction 1991 Pressing force 100 ton (1000 kN) Installation height max. 380 mm Table surface 1100 x 700 mm Outlet hole 800 x 220 mm ram surface 690 x 315 mm Frame width 1150 mm Lateral upright width 410 mm Dobvcogp T Euscqmekl Stroke rate 45 and 80 strokes/min. Clamping pin bore Ø 50 mm Compressed air requirement 8-10 bar Hydraulic tank capacity approx. 700 liters Motor power main drive 22 kW Mains connection 400 Volt, 50 Hz, 28 kW - 2 speed settings for the number of strokes (45 and 80 strokes/min.) - electronic cam controller BALLUFF, type Minicontroller BMC4K - electronic tool monitoring EBERLE, type PLS 509S - KISTLER press force monitoring system - table surface with 22 mm T-slots and ram surface with 14 mm T-slots - Electronic stroke counter - motorized height adjustment for the ram - central oil lubrication - Work area shielding through pneumatic opening protective screen - adjacent control cabinet and electrical cabinet - 2 oil coolers with FLUTEC cooling fan (oil-air cooling) - Electrical circuit diagram and printout of PLC program available - Two-hand operation on the machine Space requirement (control cabinet) L x W x H 700 x 700 x 2100 mm ( approx. Space requirement (electrical cabinet) L x W x H 1700 x 650 x 2100 mm Space requirement (press) L x W x H 2350 x 1700 x 3300 mm Weight of the press 8500 kg Very good condition

Year of construction: 1992, Condition: ready for operation (used), Working length: 4300mm, pressing force: 2000kN, connected load: 15kW, weight: 18t, including tools. Dobvei Dx Sbjccqmskl

Condition: used, Single column eccentric press WEINGARTEN type ERV 40 Machine No. 537 / 65 Year of construction 1965 Compressive force 40 ton. throat 230 mm table size 570 x 470 mm ram surface 250 x 200 mm Djbvcjffm Hhocqmjkl clamping spigot bore Ø 40 mm installation height max. approx. 520 mm stroke adjustment 8 - 88 mm slide adjustment travel 63 mm Stroke rate 70 strokes per minute Drive power 3 kW Mains connection 380 Volt, 50 Hz - Table height adjustment - Overload protection by crushing plate - clutch-brake combination by WEINGARTEN friction thread clutch - electric 2-hand operation and foot switch - central lubrication via hand pump space requirement L x W x H 1600 x 1150 x 2300 mm weight approx. 2,6 ton.

Year of construction: 1981, Condition: ready for operation (used), Working length: 4000mm, pressing force: 3000kN, distance between the columns: 3550mm, table width: 500mm, installation height: 460mm, connected load: 30kW, weight: 30t, with accessories and documentation. Dkobokvpgievccqmsl

Condition: used, Single-column hydraulic press HYDRAP type HPSK 25 Djbehrakvovccqmekl No. 6312 Year of construction 1989 Pressure force 25 ton. Ram stroke 500 mm throat depth 300 mm Installation height 700 mm Table surface 1000 x 500 mm Table bore Ø 210 mm Plunger surface 400 x 360 mm Clamping pin bore Ø 40 mm Table height above floor 855 mm Feed speed in rapid traverse 280 mm/sec. Pressing speed 3.5 mm/sec. to 25 mm/sec. Return speed 280 mm/sec. Hydraulic tank capacity 240 liters Drive power 7.5 kW Mains connection 400 Volt, 50 Hz. - Operation and programming via SIEMENS S5 with OP1 control system - Measuring system for stroke adjustment - Pressing speed infinitely variable via potentiometer - Pressure setting infinitely adjustable manually via pressure regulator - Short stroke device - Mechanical tool clamping on ram with T-slots and clamping pin hole - Switch cabinet with electrical control on the machine - Two-hand operation and electrical connection for foot control - Control provided for electrical mold monitoring - Hydraulic diagram and electrical diagram available Space requirement L x W x H 1800 x 1200 x 2930 mm Weight approx. 4 tons good condition

Year of construction: 1992, Condition: ready for operation (used), Max. ram force: 1600kN, length: 3170mm, width: 2500mm, height: 5080mm, weight: 23t, with documentation. Dsbvcelc N Ryecqmekl

Year of construction: 1981, Condition: ready for operation (used), There are two identical eccentric presses available, nominal force: 1000kN, stroke speed: 30-85/min, stroke adjustment: 20-125mm, weight: 8t, year of construction machine 1/ 2: 1978/ 1981, with documentation. Debvslc N Rveccqmokl

Year of construction: 1991, Condition: ready for operation (used), Pressing force: 3200kN, stroke: 700mm, table dimensions: 2500x1300mm, weight: 63t, with documentation. Dkobvccqjlc N R Dsmjl